Search Documents

By R. Farhat

Coating systems that yield a thermally grown oxide (TGO) protective layer have been proposed as a potential method for extending the lifecycle of components exposed to high temperature corrosion. This is particularly relevant to the petrochemical industry, where any reduction in corrosion rates can yield substantial cost reductions. The primary goal of this project is to develop a coating repair procedure and to investigate the oxidation performance of the repaired location. Electrospark deposition (ESD) was used to repair spalled segments of TGO grown on MCrA1Y substrates using various electrodes possessing mixed crystal structures. Specifically, electrodes of NiCoCrA1Y (BCC-FCC mixtures) and CoNiCrA1Y (FCCBCC mixtures), were deposited and oxidized to develop the TGO using a heat treatment of 24 hours at 1000°C in air. This presentation will focus on the microstructural evolution of the base metal and ESD repair on damaged area, in both as- deposited and oxidized forms. Results of SEM and XRD analysis will be presented.

Jan 1, 2011

By Robert S. G. Chapman, Kieran M. J. Downes

The Sulphide-Preview Lakes area is located 45 km northeast of La Ronge in northern Saskatchewan. It lies within the southern portion of the Proterozoic La Ronge Volcanic-Sedimentary Belt. Two styles of gold mineralization are present in the Sulphide Lake area , stratabound gold mineralization is intimately associated with a pyrite-pyrrhotite-arsenopyrite-bearing graphitic argillite unit within a sequence of intermediate to felsic volcaniclastics. Past operators established three mineralized zones along this horizon with combined reserves for two of the zones, of about 175,000 tons at 0.22 oz/ton Au. In the Preview Lake area , gold mineralization occurs in variably sheared gabbro/quartz diorite sills within a mixed sedimentary-felsic volcaniclastic sequence. Gold occurs with arsenopyrite, pyrite and minor chalcopyrite associated with quartz veins and stringers. A sulphidebearing graphitic argillite unit occurs in close proximity to the mineralized shears. Past operators delineated seven mineralized shear zones, two of which were drilltested. Average gold grades reported are in the 0.1 to 0.2 oz/ton range with erratic values up to 5.0 oz/ton.

Jan 1, 1986

By M. Boussuge

Ceramics and refractories have many common constituents and consecutively exhibit several analogous properties. For example, concerning the thermomechanical properties this paper will focus on, the type of creep that can be observed in both materials is often the same (kinematic hardening). Changes in microstructure (phase transformation, dehydration, sintering, crystallisation,...), induced by heating and/or cooling, can also drastically modify the mechanical behaviour of ceramics and refractories. But the coarse granulates, the porosity and the impurities contained in industrial refractories may lead to specific responses of this material to thermal and/or mechanical loadings. In particular, some differences can be observed with technical ceramics in the main type of damage observed in service : diffuse damage in refractories (microcracking) and localised damage in ceramics (macrocracking). In this paper, the possibilities of transferring a part of knowledge from ceramics to refractories will be discussed, in the field of thermomechanical properties : experimental characterization techniques, mechanical behaviour models. Finally, some problems caused by scale effects and by the integration of thermomechanical properties of refractories in the numerical simulation of industrial structures will be evoked.

Jan 1, 2004

In recent years, China and India have emerged as major players in the copper sector. Over the last decade, around 50% of additional global refined copper usage growth can be attributed to them. The paper provides an overview of the current and future copper supply and demand situation in both countries. Results from two market studies commissioned by the International Copper Study Group (ICSG) are complemented with recent copper statistics on North-East and South-East Asia, as well as further sectoral analysis. Developments and trends in copper mining and metal production, semis production, and major end use areas are highlighted. While providing insights into sectoral patterns and growth trends, the paper provides the basis for comparing structure and output of the copper sectors in some of the major copper-using countries in Asia. Afterwards, the current copper reservoir in use associated with infrastructure, buildings, industrial equipment, transportation systems and households is assessed using the ICSG Copper Flow Model. Finally, the identified copper flows are analyzed regarding the potential impact on the future world supply and demand situation.

Jan 1, 2007

By N. Schmitt, E. Blond, F. Hild

Working linings of steel ladles progressively damage during the steel manufacturing process due to both severe thermomechanical and chemical stresses. In the framework of the coupling scheme proposed by Blond et al. (1), this study examines the effects of the thermomechanical loading on the onset of microcracking by considering that the complex microstructure of the slag-impregnated brick is fixed during the steelmaking process. The behaviour of the refractory is identified by using thermoelastic-(asymmetric)viscoplastic constitutive equations. Numerical simulations of a simplified geometry of the lining subjected to cyclic thermal loadings at the inner side are shown. Two cases are analysed, namely, i) the material is a homogeneous continuum with a thermoelastic-(asymmetric)viscoplastic behaviour, ii) the material is porous and saturated by liquid slag, and the skeleton has the previous non-linear behaviour. The stress and strain fields are shown, and for the porous medium the interstitial pressure of slag as well. Comparisons between these assumptions are made to assess the role of slag on the degradation of the working lining.

Jan 1, 2004

By K. G. Eriksson

"The first tentative test made to try rubber lining in grinding mills was made in the early twenties. However, because of poor rubber compounds and design the results did not prove to be promising.In the early sixties successful trials of rubber linings were carried out as a result of a cooperation between boliden AB and Skega AB.One of the reasons rubber was not used earlier for linings was the difference in wear characteristics between rubber and steel. The ability to successfully develop rubber mill liners depends on three factors:l. Design2. Material (rubber compounding)3. Experience (knowledge)DESIGNThe main difference between steel and rubber, in material aspect, is the elasticity and the low tensile and shearing strength of rubber. It is necessary to take maximum advantage of the elasticity and to reduce tensile and shearing forces by minimizing the sliding of the mill charge. This is accomplished by using the Lorrain type of liners, i.e., lifter bars and plates. It is, however, necessary to keep a certain balance between lifter bars to optimize liner life and grinding performance."

Jan 1, 1983

By K. L. Eastwood

The ISA PROCESSTM cathode plate is characterised by its copper coated suspension bar, coupled with a blade employing austenitic stainless steel alloy 316L. The blade material has become the mainstay of the technology and has been closely copied by competing cathode designs. Improvement to the cathode plate design remains a key area for research, and ongoing developments by Xstrata Technology's ISA PROCESSTM have recently been commercialised. Two such developments are the ISA Cathode BRTM and ISA 2000 AB Cathode. The ISA BR cathode is a lower resistance cathode that has proven to enhance operating efficiencies. The AB cathode was designed to improve stripping inefficiencies in the ISA 2000 technology. These developments have now had time to mature and their long term performance will be discussed. Rising material costs and the desire to extend the operating boundaries of the standard 316L cathode plate has triggered a number of significant advances. These involve the use of different stainless steels as alternatives in some operational situations. The technical aspects and results of commercial trials on this development will also be discussed in this paper.

Jan 1, 2007

By J. Lu

The impact of acid treatment in agglomeration/acid curing on copper extraction and acid consumption was investigated with respect to acid dosage and moisture. Without the addition of water, no agglomeration occurred. At an acid dosage above 15 kg/t, the acid was not completely consumed during acid curing. With the addition of 6.2% water, the particles agglomerated together. Copper, iron, magnesium and manganese were dissolved as sulfates and enriched in the fine fraction of the ore. The copper extraction and net acid consumption increased with increasing acid dosage. The copper extraction for acid curing with the addition of 6.2% water was higher than that without the addition of water due to the improved permeability and the increase in the contact with acid-soluble copper. During acid curing, the reaction of sulfuric acid with muscovite, abite and nacrite mainly took place on the surface of the particles while the reaction of sulfuric acid with clinochlore occurred not only on the surface but also inside the particles.

Jan 1, 2007

By P. V. Barr, Y. -H. Li, A. P. Watkinson

Subsequent to a campaign of pilot-kiln trials of firing bio-oil and natural gas, scale-up to commercial lime kilns was made using an in-house mathematical kiln model. Both dry limestone and lime mud kilns of 3.5 m OD. by 100 m length were used for bio¬oil firing simulations. Comparisons were made against natural gas firing on the basis of specific firing rate, off-gas volume, energy consumption and overall lime quality. Model simulation results indicate that conversion from natural gas to bio-oil with no productivity loss will increase energy comsumption by about 7.5% and total off-gas volume by about 8%. Alternatively, a 6% decrease in productivity would be expected if off-gas volume is maintained constant. The calculations are sensitive to deviations in the lower heating value (LHV) used in the simulations. A 5% increase in the LHV of the bio-oil, which could result from a 3% decrease in the moisture content, reduces the energy penalty to 2% coupled with a slight reduction in off-gas volume.

Jan 1, 2004

By Emilie Williams

The Mouska Mine uses primarily shrinkage mining to extract the narrow veins that contain its mineralization. Mining is currently occurring on levels 12 to 14, reaching depths of 800 m below surface. Although the mine is not considered ?deep?, no backfill is available to fill empty stopes and certain areas remain open for over 500 m in height. As only narrow sill pillars remain to separate the levels, a highstress environment is created. Seismic activity was first observed when mining reached Level 11 (600 m deep) and has steadily increased since then. Seismic activity is associated with the highly-stressed sill and rib pillars; no geological structures have demonstrated significant seismic potential to date. In response to this increase in activity, pillar dimensions have been increased with depth and dynamic ground support has been installed. Seismic and pressure monitoring have been implemented, among other types of instrumentation. The following paper further describes the challenges associated with using conventional methods in the high-stress environment typical of the Canadian Shield, as well as several solutions implemented to mitigate these risks.

Feb 1, 2008

By D. Seke, E. Katsande, R. Khumalo, K. Seerane

Palabora Mining Company (PMC) processes a multi-component ore body using a circuit consisting of two AG mills in parallel, closed with vibrating double deck screens and hydrocyclones. The bottom screen undersize feeds the hydrocyclones, but the screen oversize products can be treated in a variety of ways. The top deck screen pebbles can be crushed and then combined with the bottom deck oversize and recycled to the AG mill. Alternatively both the top and bottom deck screen oversize can by-pass the recycle crusher and be recycled directly to the mill. A full tap-off is a configuration when both the top and bottom deck screen oversize streams are stockpiled. The other configuration is when the bottom deck screen oversize is recycled to the mill while the top deck screen oversize is stockpiled - termed partial tap-off. This article reports the findings from the surveys performed to evaluate the performance of the PMC auto mill circuit when operated under the four different configurations discussed. Ore characterisation tests were performed to assess the deportment of the key ore components for the different configuration.

Jan 1, 2012

By J .. R. Dalton

"Blasting in high sulphide content ores presents at least two major safety considerations: (1) compatibility of the explosives with the ore while resident in the borehole; and (2) introduction of a flame and shock producing explosive into this environment, while minimizing the risk of reactive ignition in the chemical reaction products/sulphide dust cloud resulting from the detonation. This paper will discuss only the second consideration, i.e. post detonation reactivity.The ETI (Explosives Technologies International) Technical organization, in consultation with the U.S. Bureau of Mines, reasoned that the most relevant considerations in the development of an explosive for this application are:• minimization of reactive gaseous detonation reaction products;• flame duration reduction;• flame temperature reduction;• increased explosive sensitivity;• reduced probability of ""low order"" detonation; and• maintenance of energy level as high as possible.Obviously, not all of these are totally independent properties, i.e. increased sensitivity will reduce the probability oj low order detonation as will higher energy levels. However, these considerations were examined separately as if they were independent."

Jan 1, 1994

By Peter D. Cunningham

At Vale Inco in Sudbury, underground mobile equipment production and maintenance data is presently collected manually from paper slips. This paper reviews a pilot project that developed a system to electronically collect that data. The benefits and improvements in data accuracy, timeliness and reduction in collection effort, will be discussed. Technological issues that arose from the use of WiFi, RFID (Radio Frequency Identification) and the IREDES mine data equipment standard are also discussed.

Oct 1, 2009

By Paul Stothart

Agenda 1)Key Political and Policy Issues 2)Relevance to the Mining Sector ?All parties vying to be the greenest ?Regulation, indoor air, health issues combined into Clean Air Act ?International carbon markets ?Kyoto Protocol ?legal force ?Spawning clean energy technologies? ?Effectiveness of present approaches?

May 1, 2007

By Paul Stothart

Context ? Industry is active in urban, rural, and remote regions ? Faces a range of environmental challenges and ?social license? issues ? There are also Aboriginal and northern issues ? Also very active internationally, with associated challenges ? Environmental/social groups often target the industry ? The important contribution of the industry should not be overlooked Useful Minerals and Metals Minerals are intrinsic to the residential, municipal, communications, and transportation infrastructure of modern life. Examples: Hybrid motors - nickel hydride batteries Water purification systems ? nickel, rare earth elements Catalytic converters - cerium Screens and monitors - several rare earth elements Clean electricity - uranium Circuitry - gold, copper, aluminium, lithium, titanium, silver, cobalt, zinc Instruments - copper, silver, nickel, cobalt, copper, brass Protective products ? zinc, calcium carbonate, sulphur

May 1, 2008

IBI Alliances ? Government ? People ? Academic ? Associations ? Media ? Customers ? Agencies ? Shareholders ? Industry consultants ? Investment Authority ? Geological Survey ? Department of Mines ? People ? Local Residents ? Mineworkers ? Academic ? University of Guelph ? Uganda Vermiculite Institute ? Associations ? TVA ? Organic Certification ? Media ? Canada ? International ? Customers ? Advocacy role ? Agencies ? Regional International

May 1, 2006

"The Kidd Creek concentrator is situated adjacent to Highway 101, twenty-four kilometres east of the center of the city of Timmins, Ontario. Sulphide ore, received by train from the minesite twenty-nine kilometres away, is processed at a rate of twelve thousand metric tonnes per day. Saleable concentrates of copper, zinc, lead and tin are produced.The concentrator contains secondary crushing, grinding, flotation, gravity separation and concentrate handling facilities. The total concentrator manpower complement is one hundred and sixty-four which includes supervision and operating personnel. Twenty-one shift personnel are required to operate the processes involved and they occupy fifteen different operating positions in addition to that of the supervisor. These positions include:1 Central Control Operatorl Metallurgical Leader1 Dryer Control Operatorl Crusher Leader3 Copper-Lead-Zinc Flotation Circuit Operators1 Pyrite Flotation Circuit Operator1 Tin Plant Operator2 Grinding Operators1 Concentrate Operator2 Crusher Operators1 Spare Operator1 Tailings Area Operator1 Automatic Sample System Operator1 Dryer Area Helper1 Crusher Helper1 Tin Plant Helper"

Jan 1, 1981

By Tom Shumka

All mineral processing facilities that use girth gear driven mills need to inspect the gear teeth on a routine basis, whether it is every six months or every three years. The inspection frequency depends upon gear tooth condition, and the objective is to ensure operational integrity of the gear teeth. Conventional methods such as magnetic particle testing, visual inspection, or dye penetrant examinations rely heavily on interpretation. At best, these techniques can determine whether a defect exists, but are unable to provide information on defect severity. This paper describes the use of combined Eddy Current Array (ECA) and Alternating Current Field Measurement (ACFM) to provide a complete survey of all surface breaking indications on the whole gear tooth depth. This method accurately determines the size, length and depth of any cracks found on the surface.

Jan 1, 2012

By Michael Fuller

Roadmap ? Examples of Partnership from UBC ?? Event Sponsorship ?? Recruitment & Connections ?? Opportunities ? National Recruitment Survey Results ? Conclusion with Key Points Event Sponsorship ? Annual Canadian Mining Games competition ?? 160 senior mining engineering students, from 10 universities ? Field Trips ?? 2nd year: Open pit ? Highland Valley Copper ?? 3rd year: Underground ? Myra Falls, Quinsam Coal ?? 4th year: Self-organized ? Chile, China, Poland, Brazil

May 1, 2008

By Qidong Xu

Abstract - The metavolcanic rocks of the Dahongshan area have been subjected to both widespread hydrothermal alteration from circulating seawater and to regional metamorphism, such that their mineralogic and chemical compositions have been changed significantly. Studies of immobile elements show that these rocks were originally tholeiitic basalts with geochemical characteristics of T-type MORB formed in a mid-ocean ridge environment. The accompanying Cu-Fe-rich VMS mineralization is in keeping with the original petrology and tectonic setting of these metavolcanic rocks. Regional alteration evident in K-Mg enrichment is related to sericitization and chloritization. Local alteration associated with Cu-Fe mineralization appears to have been accompanied by Si enrichment and Na depletion. P enrichment identifies metasomatism related to Cu-Fe reconcentration in the mineralized zone.

Jan 1, 1999