Search Documents

By C. M. Campbell

In his report on the Coal Resources of Southern Vancouver Island, Mr. J. D. MacKenzie stated that: "For various reasons it has been imagined that the coal deposits of Vancouver Island are extremely large and readily available." "Unfortunately," he added, "neither of these assumptions is correct." The chief disability under which the Island mines now labor does not concern the extent of the deposits. There is ample coal for the present demand. It does, however, concern the availability of the coal. If it were readily available the fuel-oil competition would not be serious and there would be no competition with Alberta, American, Welsh, or Australian coal along the Pacific Coast, for Vancouver Island coal could be produced at a price that would cut out all competition. The outstanding operating difficulty common to all Island mines is the extreme irregularity of the coal seams. To most people a coal seam is synonymous with uniformity, and in most coal seams a condition found at one point will be repeated at other points in the same seam throughout the basin. The accompanying drawings show how very far this is from being true in the Cassidy mine, which, in many respects, is typical of Vancouver Island mines. Figure I is a plan covering about 160 acres of the Douglas seam, the only workable seam in this part of the district. The area shown represents what has been the best producing part of the mine and indicates the very large percentage of the seam where the coal is either entirely lacking or so small in amount that it cannot be profitably recovered.

Jan 1, 1924

In-Situ Leaching (ISL) process plants are low cost producers for uranium deposits where the geology is suitable. In the 1970s, a three-year pilot ISL program occurred on gold ore from the Ajax Mine, Cripple Creek District, Colorado, using a chloride and iodide solution [1]. The test was halted due to poor results. With gold and silver the international ISL progress has been slow; however the potential for low capital expenditure (CAPEX) and operating expenditure (OPEX) with large low grade deposits is real. Unless the metallurgy has been demonstrated there are significant risks which could be fatal flaws to an ISL gold or silver project. The metallurgy of gold ISL projects is far from simple and it is early days with project development.

Jan 1, 2011

By Yufeng Yao, Robert P. Lowell

Abstract - Conductive heat flow anomalies associated with hydrothermal sulfide mounds on the seafloor have been studied. Sulfide mounds tend to focus conductive heat flow because sulfide minerals have a greater thermal conductivity than country rock. The topography of the mound above the seafloor, however, leads to a reduction of heat flow, particularly near the center of the mound. Because the focusing effect is constant, whereas the topographic effect decreases with distance away from the center, the focusing effect dominates toward the edges of the mound. The magnitude of these effects depends upon the conductivity contrast and the height/radius aspect ratio of the mound. Conductive heat flow anomalies at sulfide mounds also result from fluid circulation within the edifice. For the active and relict mounds at the TAG hydrothermal field, which have an aspect ratio of approximately 0.3 and a conductivity contrast of 3, the heat flux through the center of the mound should be roughly 70% of the background heat flux. The maximum effect of heat flow focusing is to increase the heat flux by about 30% above background. By comparing these effects with conductive heat flow data at TAG, we find that advective processes dominate conductive heat flow at both the active and relict mounds. Advective circulation can also give rise to much larger lateral and vertical temperature gradients than would result from conduction alone.

Jan 1, 1999

By Li Xibing

The In order to mine safely with reasonable cost, it is necessary to research the fracture characters of backfill and its matches with rock mass. Four kinds backfill with cement-tailing ratio of 0.250, 0.125, 0.100 and 0.083 respectively were tested, and basing on stress-strain curves tested, the deformation characters and fracture laws as well as the damage constitutive equations investigated with damage mechanics whose calculating results are coincided with experiment results well were proposed. The results of damage analysis show that there have different damage characters in different backfill, e. g. the lower the ratio of cement to tailings the lower the damage values when stresses reach to peak value; the lower the content of cement the more rapid in damage and the more abrupt in breakage process. In addition, using catastrophe theory, an energy model was proposed for backfill and rock mass acted each other in mechanics, and the unstable condition of the system was obtained. Research results show that the higher is the stiffness of rock mass the more stable the system, and the lower is the ratio of cement to tailings, the more unstable the system will be. Further more, according to the catastrophe model proposed, the reasonable matches between backfill and rock mass were researched, and a calculation formula that designs reasonable strength of backfill during mining was put forward. It has been proved by practice that the model and theory researched in this paper can guide filling design in mining. Keywords: Cemented tailings backfill, constitutive equation, catastrophe theory, match of backfill and rock mass

May 1, 2007

By S. Zakaria

"Inco's Automated Haulage Truck System (AHT) is a revolutionary automatic guided vehicle that performs all load, haul and dump operations without human intervention. The high level of sophistication and the short period it has been in operation has only allowed a select few Inco personnel to become familiar with the ART operation and maintenance. As an aid to operations an expert system using the knowledge gained from the experienced specialists was implemented in the field.The AHT operating and maintenance assistance expert system will reason through the information given, arrive at conclusions and give advice to operations, technical and management personnel. It will provide comprehensive real-time troubleshooting assistance for the hydraulic, electrical and mechanical subsystems of the ART. The ART expert system has many benefits to Inco which include increased skill levels of ART operations and maintenance personnel, reduction in ART downtime, standardization of troubleshooting procedures and reduction in ART operating and maintenance costs. In the future, the expert system application will be linked to SCADA (Supervisory Control and Data Acquisition), maintenance and statistical software to display current and historical trends of variables from a centralized historical database. As well, a wide variety of features will be integrated into the system including AutoCad drawings, graphics, photographs, voice and video capabilities."

Jan 1, 1994

By C. Cano

One of the main concerns within the mining industry is to minimize the impact of tailing facilities to the environment and nearby communities. Since the implementation of the first thickened tailings disposal (TTD) methodology at Kidd Creek in 1964, the thickened tailing disposal has been growing alternative disposal technology to mitigate the environmental impacts. Technical investigations on the TTD technology have been studied in detail to counteract the increasing shortage of water resources. One of the benefits observed with TTD is its resistance to potential earthquakes, particularly in zones with high seismic activity (Los Andes). TTD technology optimizes the maximum possible density for the material and generates a negative internal pore pressure in the material due to the surface and sub-surface water evaporation. This internal pore pressure should be enough to resist the pores pressure to which tailings are subject due to an earthquake action. The objective of this study is to verify the Shrinking Limit (SL) of thickened tailings during initial deposition and in the long term and the ability of tailings deposited by TTD would resist liquefaction. Fresh tailings coming from a flotation process of a copper plant concentrator were used. The samples put under cyclical three-dimensional tests associated with maximum credible earthquake magnitude range of 7.0 8.0 to develop a curve for the safety factor v/s depth for dry densities related to the maximum density obtained at the SL. At a dry density of 1.65 t/m3 liquefaction did not occur at any depth. At 90 % of dry density of 1.51 t/m3, liquefaction did not occur at earthquake magnitudes of 7.0 or 7.5 nor at any depth but liquefaction occurred at magnitude 8.0 between 0 m and 14.5 m; below 14.5 m, liquefaction does not occur.

Jan 1, 2007

By Jun Shan

The preparation of poly(N-isopropylacrylamide)-monolayer-protected clusters (PNIPAM-MPC) of gold nanoparticles was carried out in a homogeneous phase using three ways, in which three types of PNIPAM ligands were employed. The first type comprised of PNIPAMs with narrow molar mass distributions, synthesized by reversible addition-fragmentation chain transfer (RAFT) polymerization and thus, bearing a dithiobenzoate at the chain end. These polymers were used directly to passivate the gold nanoparticles upon the Schiffrin reaction in a one-pot synthesis. The second type of ligands was derived from the first one through hydrazinolysis, and they therefore contained a thiol end group. The third type of ligands was PNIPAMs obtained through conventional radical polymerization, post-modified to contain thiol end groups. The PNIPAM-MPCs were characterized by high-resolution transmission electron microscopy, and by dynamic light scattering. The one-pot synthesis utilizing the ligands of the first type turned out to be a simple and facile method, compared with the other two ways, with which the size of the gold nanoparticles can be easily manipulated mainly by adjusting the molar ratios of PNIPAM / HAuCl4. PNIPAM is a more efficient ligand to stabilize the gold nanoparticles in water and in organic solvents than alkanethiols. The surface density of PNIPAM chains ranged from 1.8 to 3.6 chain/nm2, which is much lower than that typical for alkanethiols. The thickness of a PNIPAM monolayer bound to the gold core is somewhat larger than the size of the random coil of corresponding free PNIPAM in aqueous solution, which suggests that the conformation of a PNIPAM chain bound to the gold core is to extended.

Oct 1, 2003

By J. L. Chakravarty, S. K. Dutta, S. Banerjee, D. Putatunda

"General purpose uniprocessor systems used in control applications, however fast they may be, at a certain stage attain saturation, forcing the user or designer to consider other avenues for solving the problem. This paper gives a broad overview of multiprocessing with special reference to transputers. Virtually all aspects, from parallel systems real-time control to artificial intelligence (AI) and expert systems, have been highlighted. The application of transpurters in unilayer and multilayer control are discussed in detail, with specific attention to sensor integration. Two case studies describe at length the utilization of transputers. IntroductionIn conformance with the high level taxonomy of parallel computer architectures as given by Ralph Duncan(l) (an improvement to Flynn's classification, which maintains the essential elements of useful taxonomy based on instructions and data streams), the MlMD architectures are categorized into two groups: (I) shared memory, and (2) distributed memory type. While the shared memory multiprocessors are more popular than the message-passing multiprocessors because they can be programmed in a conventional sequential fashion, their aspect of the architecture creates a perfonnance bottleneck. In contrast, message-passing multiprocessors (MPM) suffer from no such limitation and can attain linear speed increases that are directly proportional to the number of processors put into use. The MPM implementation also has its own advantages and disadvantages. Because the performance of the system is heavily dependent on it, the interconnection strategy in a distributed memory MIMD machine is of paramount importance. The transputer(2.J), a multiprocessor node of the distributed memory type, is becoming very popular. The advantages offered by the transputer make its application in the mining and processing industries very promising."

Jan 1, 1994

By W. Almdal

"To compete in the ever expanding global market, companies must continuously improve. Benchmarking, a tool that can help determine where the best areas for improvement are, is more than comparing measures, it is comparing how business is carried out and how decisions are made. The key to success is in integrating benchmarking results into the organization, so that those most affected by the results own them and are empowered to use them as a positive change agent. This is a necessary step to achieving substantive change to practices and achieving optimum performance improvement. IntroductionBenchmarking is a powerful tool that can assist in the continuous goal of improvement. Benchmarking is more than comparing productivity rates or unit costs, it is seeking out best practices and assimilating them into a business to provide a positive change agent.Benchmarking is a continuous process - is time consuming, labour intensive, and requires a lot of discipline. There are no easy answers and no easy solutions, just a lot of work. The results, however, are nothing short of spectacular. More and more companies are adopting benchmarking practices because it is a key tool of the learning organization and will become part of the way business is done, part of the way it is managed. Business must change to stay ahead or to get ahead and benchmarking can accelerate the process of business change. Improvements in an organization can happen faster and more effectively with a benchmarking approach."

Jan 1, 1994

By G. A. Gillett, C. F. Bonney

"The Davy McKee combined mixer-settler (CMS), is a liquid-liquid contactor, which has been commercially applied to the recovery of uranium from dilute sulphuric acid-bearing leach liquors. CMS differs from most other solvent extraction systems in that the mixing and separation of the phases is carried out in the same vessel.IntroductionTypical solvent extraction plants for the recovery of uranium operate at organic to aqueous feed flow ratios of 1 : 2 to 1 : 30. Because it is beneficial to mix the organic and aqueous phases at an organic/aqueous (O / A) ratio of between I : 2 and 2 : I there is incompatibility between the over-all and operating O /A ratios.Conventional mixer-settler designs require an external recycle of the minority flow which results in the possibility of over-mixing, increased settling requirements and entrainment losses. Other workers have approached this problem in terms o f enhanced sett ling and this has been partly successful.Davy McKee's approach involved a radical rethink of the principles of liquid-liquid contact and separation.Description of CMSThe CMS has the important advance that the required mixing O/A ratio can be achieved without external recycle and is not affected by the O /A ratio of the feeds. Three zones co-exist within the CMS unit-a central mixing zone and upper and lower separation zones. A pump impeller on a draught tube is installed within the mixing zone and baffles are installed above and below the mixing zone. Conventional mixer- settlers have several undesirable features which ca n largely be eliminated using the CMS system:"

Jan 1, 1983

By S. Shokri

The increasing size and complexity of mega construction projects result in having several geographically distributed stakeholders, collaborating with each other to successfully deliver the project. Electronic Product and Process Management Systems (EPPMS) are recently emerging to facilitate the collaboration between stakeholders, reduce the surprises and issues, and improve the project productivity. These are commercially successful but evolving systems. An important component of EPPMS is the Interface Management System, which aims at formalizing and automating the communication channels between stakeholders. An interface is generally considered the link between construction elements, phases, or stakeholders. An interface Management System (IMS) involves five iterative steps: (1) Interface Identification, (2) Interface Documentation, (3) Interface Transferring, (4) Interface Communication, and (5) Interface Closing. A fundamental part of step 2 is recognizing different roles in dealing with interfaces. Each stakeholder is assigned a different role, such as responsible, accountable, consulted, and informed. In a mega project, several thousands of interfaces exist with complex relationships between stakeholders. Therefore, identifying stakeholders with higher responsible roles has been requested as useful information to the project owner in dealing with some of the project risks. After the interfaces are determined, and the responsibilities are allocated, the critical stakeholders are identified using the centrality concept in Social Network Analysis. The critical stakeholders can be determined at the highest level, considering all types of interfaces, as well as for each specific type or discipline-related interfaces. The proposed methodology is applied on a hypothetical offshore project with over 500 interfaces. In fact, this project is a simplified representation of a real scale Liquid Natural Gas project. In order to reduce the complexity of calculations and clarity of explanations, the simplified case study is used. By implementing IMS in mega projects, different parties not only formalize the communication between each other, but also gain better visibility concerning their roles and responsibilities. In addition, the owner benefits from analysing the complex relationships between stakeholders to further identify critical ones, along with other criteria like package cost, stakeholders? experiences, etc.

Aug 1, 2013

By Jean-Luc Collins

"The paper deals with the impact of fleet imbalance on a deterministic evaluation of shovel fleet productive capacity. It shows that if the fleet imbalance is overlooked, then estimated fleet productive capacity will be overrated.The paper shows that fleet imbalance inflates utilization, and care must be taken when using such statistics which are derived from reported field-equipment-hours. It shows that the utilization must be deflated by a factor called 'balancing efficiency"" in order to estimate shovel productive capacity correctly. The paper also shows how fleet imbalance can be controlled by managing idle time or downtime in an actual operation.The technique used for measuring the balancing efficiency factor is based on statistical analysis of equipment utilization."

Jan 1, 1980

By Leopoldo Gutierrez, Sergio Castro, Lina M. Uribe, Janusz S. Laskowski

"The effect of sulfite and metabisulfite ions on the amyl xanthate flotation of copper-activated pyrite, in distilled water and seawater, has been studied by micro-flotation tests and redox potential measurements. The activation of pyrite was carried out varying copper ions concentration. It was found that in the presence of copper ions in solution, sulfite and metabisulfite are able to depress copper-activated pyrite at neutral or slightly acid pH. After the addition of sulfite or metabisulfite ions the resulting pH is more acidic with metabisulfite ions. A significant increase of the redox potential of the solution was observed as copper ions concentration increased. Then, the initial reducing conditions brought about by sulfite and metabisulfite ions, change abruptly to oxidizing conditions in the presence of copper ions. Under these oxidizing conditions, the metabisulfite showed to be an effective depressant for pyrite mainly in seawater. However, sulfite was a pyrite depressant in both distilled water and seawater. Based on these results, the pyrite depression by sulfoxy-depressants during the flotation of Cu/Mo ores in distilled water and seawater is discussed.INTRODUCTIONDepression of pyrite by sulfoxy-depressants (sulfite and metabisulfite) in the presence of copper ions is an important issue. This is particularly true when pyrite depression in the flotation of Cu/Mo sulfide ores is carried out in seawater. The use of lime in seawater must be avoided because the formation of magnesium hydroxy-complexes and precipitating magnesium hydroxide strongly depresses molybdenite flotation (Castro et al., 2014). In order to solve this problem, one large plant in Chile uses sodium metabisulfite (MBS) instead of lime to depress pyrite in seawater. In plant practice, this also improves molybdenite flotation since with the use of MBS the pyrite depression is carried out at pH 6-7, instead the pH 11-12 usually employed with lime.From a general point of view, pyrite exhibits some natural floatability over acidic pH ranges and may be partially floated without thiol collectors (a coating of sulfur/polysulfides has been claimed). Therefore, pyrite flotation with xanthates is usually high in the acidic pH region, but decreases greatly at alkaline pH (Leppinen, 1990; Fornasiero and Ralston, 1992; Zhang et al., 1997)."

Jan 1, 2016

By J. E. Dutrizac, J. B. Sunstrum

"Lead was among the first metals known to man, and there are indications that lead was produced by the reductive smelting of galena in the mountains surrounding the Black Sea as early as 3000 B. C .(1). The early metallurgists soon discovered that silver could be recovered from lead bullion by cupellation techniques, and that the litharge product of the cupellation process could be reduced to give silver-free lead metal. By the Graeco-Roman era, lead-silver ores were being extensively exploited for both their silver and lead contents. Although silver was always of prime concern, a number of industrial uses existed for lead that included piping and sheeting. Subsequently, lead metallurgical practice developed steadily in different parts of the world, and was a relatively mature technology by the time of the European colonization of North America. In the United States, lead was produced on a small scale as early as 1720, and by 1800, the extensive Pb-Zn deposits of Missouri-Kansas and the upper Mississippi Valley were being developed(2). Many of the early American lead ores were low in silver, and seemed to have been worked primarily for their lead contents. Major uses of lead at the time included bullets, pipe and sheeting. During the period 1860-1890, the silver-rich galena ores of the western United States were exploited, and a number of lead smelters were operated. Although all the smelters produced lead metal, the recuperation of the associated silver and gold values was generally of prime concern. In Canada, lead deposits are abundant, and galenarich outcrops frequently attracted the attention of the early explorers and prospectors. In fact, the first record of a Canadian ore deposit seems to have been the observation of an argentiferous galena vein near Lake Temiscamingue in 17 41(3). The presence of silver-bearing lead deposits naturally attracted the attention of the mining community, and many outcrops were worked throughout the country. Because of the problems associated with transporting lead concentrates to existing American or overseas smelters, attention soon shifted to the establishment of local lead smelting facilities. The purpose of this article is to examine those early smelting efforts and to try to identify the first ""successful"" Canadian lead smelter."

Jan 1, 1999

By Rolf Andreas Lauten, Guy Kluck

"Formation of scales may have important detrimental effects in many mineral processing applications. A well-known problem is the need for frequent maintenance to remove scale from processing equipment. Another challenge may relate to encapsulation of valuable minerals in precipitating scale. In this work, we explore the ability of some crystal growth inhibitors to prevent or lower the degree of scale precipitation. In many situations pregnant leach solutions contains substantial concentrations of calcium, magnesium, sulfate and carbonate in addition to dissolved valuable elements, e.g. gold, copper, zinc. Together with non-dissolved gangue minerals, some slurries may also contain particulate gold, copper etc. During normal processing of the pregnant leach solution it may be exposed to temperature gradients or similar promoting precipitation of various scales. Valuable minerals may become entrapped in precipitates and thus become inaccessible to the lixiviant. Use of a crystal growth inhibitor may lower the degree of encapsulation of valuable elements.Using a simple model system, supersaturated with respect to gypsum, the effect of some crystal growth inhibitors on the prevention of scale is evaluated in terms of amount precipitated gypsum, the particle size of the precipitated gypsum and the carbon gold loading capacity.INTRODUCTIONGold bearing sulfide ores are often roasted or pressure oxidised prior to leaching. The purpose of this unit operation is to prevent loading the leaching circuit with sulfides that consume cyanide. Pressure oxidation or roasting chemically converts the sulfides into sulfates and at the same time, the pH of the slurry ends up in the acidic range. Typically, lime addition is the preferred means to raise the pH to around 10 where gold leaching takes place. Combination of large amounts of calcium ions from the lime with sulfate ions from the ore induces precipitation of gypsum. Compounds like calcium carbonate may also precipitate if carbonate ions are present in the slurry. Depending upon the composition of the ore, compounds like calcium carbonate and other types of scale may also precipitate on gold surfaces on the slurry particles. A layer of scale on top of exposed gold surfaces will prevent dissolution in the cyanidation that takes place during leaching. Naturally, such a precipitation may lower the gold recovery."

Jan 1, 2016

By R. H. McCorkell

Radon emanation rates. J. and compositions of materials from the Canadian Certified Reference Materials Project (CCRMP) indicate that the fraction of the Rn produced that escapes, E, is usually 1% to 8% and the 238U decay chain is nearly in secular equilibrium. For some Chinese ore standards, E values are higher than f or the CCRMP materials. Standard ore tailings have 2/oPb concentrations higher than expected from their 226Ra concentrations and Rn escape rates (12 - 34%) . Biological materials have E ˜100%, their ash E ˜0%. Pelletizing ore powders at 20 000 lb/in2 reduces J by only 20 - 40% but only 2% of Rn escapes from pressed Li2B4O7 pellets and 0.01 - 0.04% from fused Na2B4O7 or Li2B4O7 discs. Large, difficult-to-explain random variations in J are observed in some situations but several highly reproducible ways of measuring emanation rates have been found.

Jan 1, 1986

By G. J. Kipouros, N. Dadvand

"In recent years coatings of alloys have been produced for a wide range of applications including many for wire bonding application. The main characteristic of the baths of electroless plating is the presence of sodium hypophosphite as a reducing agent and also as the supplier of phosphorus. In the electroplating of alloys the Watts bath is predominantly used. This presentation compares the two techniques, electroless plating and electroplating, and discusses the possibilities of cross utilization of sodium hypophosphite in an attempt to formulate baths that eliminate the waste disposal issue related to some components.INTRODUCTIONThe importance of surface characteristics and the linkage of surface coating process to surface characterization has given rise to the evolution of surface engineering. Not only the surface preparation and morphology has become very important to the coating technology but also the knowledge of surface area exposed to the process of coating or corrosion is absolutely essential in ascertaining the behaviour of coatings and their adherence to the substrate. The above concepts are not unknown to researchers involved in the protection of surfaces, particularly metallic, from corrosion and/or erosion corrosion. However, the complexity of the surface defects, roughness, porosity, interconnected porosity and other related factors have contributed to the uncertainty of the true surface area versus the nominal surface area. Therefore critical parameters such as current density and chemical surface intensity although have been studied extensively at the atomistic level by carefully prepared surfaces are very difficult to be determined at the practical scale required during the coating processes.The most pronounced case calling for an understanding the relationship between the surface area and the effective protection is the coating of surfaces of items produced by compression or consolidation of powdery materials. With the advent of nanomaterials and the additive manufacturing through 3D metal printing this issue is becoming more important. Certain experience in this field come from the accumulated knowledge resulted from the attempts to characterize the electrochemical behaviour of powder metallurgy metals and alloys. Powder metallurgy has been a well-established process for half a century on basic metals such as iron, copper and their alloys. Recently the development of powder metallurgy process for aluminum, titanium and attempts to develop powder metallurgy processes for magnesium and its alloys has brought to light another important issue that of the development of coatings on difficult to plate reactive metals such as aluminum and magnesium. Despite of many successes in the development of powder metallurgy alloys the exact characterization of the corrosion behaviour of the coatings and the substrates is difficult to determine because of the unknown morphology of the exposed area i.e. the exact morphology and area of the exposed surface (Samal, 2007)."

Jan 1, 2016

By A. Burduk

The traditional approach to managing information flow between a mine underground and overground, applied in copper mines of KGHM Polska Miedz S.A., is mostly based on exchanging spoken information using the mine telephone network and printed documentation. This way of information flow significantly influences effective use of time of a shift foreman employed at a mining division. In order to minimise multiplication of significant information generated as paper documentation, a concept of an IT system module to input basic data concerning operation of the mining division was developed. The idea is based on computer software that permits inputting data in the underground and their immediate sending to the overground. The above-mentioned solution will permit significant reduction of administrative work time that each foreman has to do on each shift. The time saved on filling forms and communication will permit the foreman and the other workers involved in information flow to spend more time for execution of their basic duties. In the case of the supervision employees working in the overground, the IT system will allow all the interested persons to be informed directly, with no necessity to transfer the information on the situation in the given mining division by turns from one to another. On the other hand, saving time on administrative works will permit the foreman employed in the underground executing more detailed inspection of workplaces in his subordinate mine division. Thus, availability of the foreman for the mining division operation will be improved. KEYWORDS

Aug 1, 2013

By Xuanxue Mo, Zengqian Hou

"Yidun Island Arc in Sanjiang Region is one of the important Kuroko-type volcanogenic massive sulfide deposits (VMS) districts in southwestern China. Tectonically, the region is situated in the eastern portion of the Tethys orogenic belt, and is a late Triassic extensional island-arc. The island-arc underwent earlier arc construction, intra-arc rifting, later arc construction and backarc spreading during its evolution and formed a complete trench-are-basin system, i.e., the Ganzilitang suture zone, forearc basin, outer are, intra-arc rifting zone, inner arc and back-arc basin from east to west across the island-arc.Kuroko-type VMS deposits and occurrences discovered so far are limited to within the intra-arc rifting zone of the Yidun Island Arc and tend to occur in groups or clusters distributed in separate faultbound basins; e.g., Zengke, Gacun and Xiangcheng basins, in which submarine volcanic rocks, especially bimodal volcanic suites, were extensively developed. The VMS deposits formed in the waning stages of volcanic eruption in the late Triassic and are hosted in the uppermost section of acidic volcanic rocks (rhyolitic-dacitic) within a bimodal suite. The orebodies are associated with these host rocks: rhyolitic-dacitic pyroclastic rocks and exhalites and chemical sedimentary rocks.All VMS deposits in Sanjiang are of the Zn-Pb-Cu type. The architecture of the deposits is twofold, consisting of concordant lenses and layers of massive sulfides and an underlying discordant stockwork. All deposits show metal zoning. The hydrothermal alteration related to mineralization is strong and asymmetrical, and is found dominantly within the stockwork zone and host rocks surrounding the ores. There are two alteration patterns: (1) chloritization - sericitization - silicification from outer sides to core of the alteration pipe; and (2) silicification + sericitization - silicification + carbonate from the lower to upper part of the alteration pipe.The mineralization temperatures of ore-forming fluids vary in the range 200°C to 335°C. Thermal evolution of the fluids displays temperature profiles that first increase and then decrease with progression of mineralization processes. The majority of black-ore minerals (Groups I and informed during intensifying stages of hydrothermal activity, and the majority of semi-yellow-ore minerals (Group III) formed during a thermal maximum. There followed the formation of fine-grained black-ore minerals (Group IV), which interacted with barite layers during decreasing temperature phases.Oxygen and hydrogen isotope studies show that the sources of ore-forming fluids for the Kurokotype VMS deposits are two-fold: seawater and magmatic hydrothermal solutions, represented by the Kuroko deposits in Japan and Kuroko-type VMS deposits in Sanjiang, respectively. In the latter case the hydrothermal solutions reacted with host rocks and mixed with cold seawater percolating downward, and circulated through volcanic rocks resulting in development of alteration zones and formation of ore minerals in Kuroko-type VMS deposits."

Jan 1, 1993

By I. Ueda, S. Ishikawa, T. Nagata

“O-SR process” in which the S-Furnace of the Mitsubishi process is followed by existing reverberatory furnaces (RFs) and Peirce Smith (PS) converters has been operated since December 2007. The S-Furnace smelts copper concentrates to produce molten matte containing 58-62%Cu which is then settled in the RFs and converted to blister copper in the PS converters. The SO2 gas generated from the S-Furnace and PS converters is converted to sulfuric acid in the acid plants. In addition to the smelting copper concentrates, the O-SR process has advantages in terms of recycling various waste/secondary materials. Automotive Shredder Residue (ASR) has been treated in the RF to reduce fossil-fuel consumption in RFs, and to recover various metals included in ASR as well, since 1993. Electronic circuit boards (E-scrap) has also been processed in order to recover not only copper but also rare resources such as gold, silver and PGMs since 2013. Strategic modifications have enabled expansion of the processing volume of E-scrap. Enhancing recycling of wastes and scraps from urban mines while reducing the consumption of natural resources in the “O-SR” process will be demonstrated and discussed in the present paper. INTRODUCTION Onahama smelter and refinery has been operating as a custom smelter since 1965. Smelting facilities were subsequently expanded to two green-charged RF furnaces and five PS converters in 1973. Since RF is a conventional old-fashioned smelting furnace that necessarily consumes a huge amount of fuel to smelt copper concentrates, saving fuel cost has been an important objective. In early 1980’s the fuel was changed from bunker oil to pulverized coal, while utilizing the combustion heat of waste tires. Furthermore, treatment of combustible waste such as shredder residue (SR) was initiated in order to save fossil fuel for smelting concentrates in the RFs. Since enhancing of the treatment of SR requires a reduction in concentrate smelted in the RFs, most concentrates were dried and injected through tuyeres into the PS.converters. These modifications enabled to reduce the amount of the pulverized coal combustion and to increase SR treatment in the RFs. SR treatment capacity has increased to 12,000mt/month because the SR market has grown after the enforcement of the Vehicles Recycling Law. Such business environment has been attributed to establish the thermal-materials recycling system of SR in which the RFs have changed their role from copper concentrates smelting furnaces to waste materials combustion furnaces.

Jan 1, 2019