Search Documents

Innovation ? In economics a change must increase overall value, customer value, or producer value. ? Innovations are intended to make someone better off, and the succession of many innovations adds growth to the whole economy. ? Innovation may refer to both radical and incremental changes to either products, processes or services.

Feb 1, 2008

By J. H. Canterford

The nickel industry in Australia has followed the general pattern apparent in many other regions - lots of ups and downs, successes and failures, but always plenty of challenges. Some of these can be attributed to local geographical and infrastructure factors, others to a healthy mix of corporate good luck and management countered by decisions that, in retrospect, were less than optimum. The roles of several entrepreneurs have certainly added plenty of spice! In terms of processing technologies, there was an initial heavy reliance on the use of "off the shelf' commercially proven processes such as ammonia leaching of concentrates and mattes, and flash smelting. Over the past decade there has been an increasing dominance of plant modifications and process technologies that have been developed "in house" in order to enhance project economics and exploit lower grade and more complex resources. This presentation provides an overview of the past 40 years of the major developments in the Australian nickel industry and concludes with some guesses as to where we will be in another decade or so.

Jan 1, 2005

By Karl J. C. Harries

"The following is an outline or check sheet of some things that might be looked at when considering the concept of a royalty or royalty provisions. It is not intended as a guide to what is right or wrong (that is for the parties to decide). It does not replace the discussions in this work and is not intended to be a complete or exhaustive compilation of matters to be considered. It presumes that you are familiar with the basic concepts of royalties and has been included as an aide memoire only. Use it as such, with caution and common sense, and amend it to suit your needs. Remember also that brevity can result in inaccuracy or imprecision. This is a danger in many points below.The section references are for the sections where the matter is the main subject of the section – see the index for other sections.Royalty TypesNet Proceeds [§§ 5.8.; 11.4.]• No accepted or understood meaning within industry.• Literal meaning, if not defined, would imply “net operating profit”.• Often defined as net profit with revenue base of proceeds from sale of product.• Should not be used without detailed and clear definition. Net Operating Profit [§§ 5.8.; 11.4. – referred to only]• Net profit without recoupment of pre-production expenditures.• Revenue base: usually proceeds from sale of product.• Operating costs deductible.• Some reserves may be permitted.• Recoupment of some post-production capital expenditures may be permitted.• Not often seen as basis for royalties in Canada."

Jan 1, 2003

By A. Yousefpour, M. Hojjati, G. Chouinard

In recent years, high performance thermoplastic composites such as PEEK and PEKK have been developed for aerospace applications. These materials offer, among the other properties, high toughness and damage tolerances. These are semi-crystalline materials and their processing can lead to different crystallinity that in turn have some impact on the final properties. The effect of cooling rate on degree of crystallinity of PEEK is studied to identify the processing window for manufacturing. Samples were heated at the constant heating rate of 20°C/min up to 375°C (above melting point) and held for 10 minute. The enthalpy of the crystallization was measured at different constant cooling rates of 0.5, 1, 2, 5, 10, 20, 30, and 40°C/min. After cooling, the samples were heated at constant heating rate of 2°C/min using modulated DSC. At temperature between 90°C to 375°C, two endotherm peaks were observed. Results suggest that endotherm peaks are related to a melting and recrystallization phenomenon of one crystal morphology. However, the second endotherm peak could be associated with another crystal structure or morphology.

Jan 1, 2006

By Richardson A. H.

"IntroductionSafety and training in the mineral industry will always be issues that are hotly debated and discussed.The nature of the mining industry, where people and equipment work in close quarters deep below the earth's surface, attracts a great deal of public attention and concern, especially in the areas of safety and related training activities. This concern has been carried over into the mineral processingsector which is, of course, a vital part of the mining industry.It is therefore imperative that mining people closely examine the policies, procedures and programs presently in place to determine if they meet the needs of the industry and its employees. Everyone stands to benefit: the companies, employees and the mineral industry as an important segment of the Canadian economy.Phrases such as ""Safety First"", ""Safety is Number One"", have a role to play in industrial safety programs but in reality are a shallow approach to the magnitude of the challenge. An industry must produce its products in a cost-effective way, with good employee relations. None of these objectives can be successfully achieved unless accompanied by good safety performance. Accidents both on and off the job result in very poor efficiency, high costs and poor employee relations.This chapter, Safety and Training, outlines those major areas that the author believes are necessary components for an industrial safety, health and training program, but are not all inclusive. More will surely be added as additional problem areas requiring attention are identified. The major sections discussed are: Development and Implementation of a Safety Program; Occupational Health; Training; and Audit Procedures.The author has drawn on his experience as both a mill superintendent, mine manager and superintendent of safety, health and training. The approach developed at loco Metals Manitoba Division is frequently used in this paper with examples and excerpts to better illustrate the subject, but does not represent the full scope of programs in place in the Division."

Jan 1, 1989

By E. L. Horner

"Srnoky River Coal is capable ofprocessing 3 million tonnes per year ofrun-of-mine coal at the Smoky River Coal preparation facilities to produce 2.1 million tonnes of high quality, low volatile coking coal for export markets. Multi-seam surface and underground mining operations are scheduled to maintain raw coal feed to the plant. Two beneficiating circuits wash the coal. A heavy medium cyclone circuit cleans the plus 0.5 mm coal and a froth flotation circuit cleans the minus 0.5 mm coal. Clean coal is thermally dried, loaded into unit trains, treated for dust suppression, and transported to west coast port facilitiesf or export. Plant by-products are used as thermal fuel Jn an adjacent power station. Quality control procedures ensure efficient resource recovery for a yield of uniform specification product, at a 7% ash level. Introduction Smoky River Coal operates surface and underground mines in the Smoky River coalfield. Approximately 3 million tonnes per year (mt/ a) of run-of-mine (ROM) coal can be processed at the coal preparation plant to provide 2.1 mt/ a of clean, high quality, low volatile bituminous coking coal. Coal is processed by heavy media and froth flotation cleaning circuits and is thermally dried.Raw Coal Characteristics The characteristics of the ROM coal, both in terms of quality and size consistency, vary with intrinsic seam qualities and mining methods employed. The two seams mined (No. 4 and No. 10) show distinctly different washability characteristics. Seam No. 4 contains relatively few middlings and can be readily cleaned by dense-medium cyclones and froth flotation to give a clean coal at specification ash content. Seam No. JO is more difficult to wash, and the ash content of the clean coal is higher than No. 4 seam at the same operating conditions. However, when the upper I m is excluded from the plant feed, the remaining lower section has washability characteristics similar to No. 4 seam. Coal mined by underground means sometimes contains caprock and consequently tends to be dirtier than similar coal mined by surface means."

Jan 1, 1985

By D. McFadgen

"THE Dominion Steel & Coal Corporation, through its subsidiaries, the Old Sydney Collieries and the Dominion Coal Company Limited, produces 4% million tons of coal annually from eight submarine collieries situated on the eastern coast of Cape Breton Island. The present workings have a frontage of 20 miles and extend 31/2 miles under the Atlantic ocean on gradients varying from 4 deg. to 24 deg. To date, some of the workings have reached .a depth of cover up to 2,800 feet.The pitching seams, the annual seaward advance, the resulting depth of cover and the rdatively soft roof and floor have necessitated the adoption of extensive longwall mining, with room-and-pillar mining con-fined to areas above the 1,000 foot cover line, where 60 per cent of the -coal is left standing in pillars to support the ocean floor. Longwall mining accounts for 87 per cent of the total production with the remaining outputs obtained from room-and-pillar work and the narrow work development. Seventy-four per cent of the longwall production and 41 per -cent of the room and development production is completely mechanized.Although 2 tons of water is pumped from the collieries for each ton of coal mined, the working sections are relatively dry as the heavy make of water is essentially surface drain-age from the land crop areas. The dry workings and the long haulage distances, which in many cases exceed 4 miles, have resulted in a continuing programme to combat the dust hazard, both at the working face and along the mine roadways."

Jan 1, 1960

By H. M. Roscoe

Fifty per cent. increased lump coal production and at the same time a reduction of from 20 to 40 per cent. in explosive consumption. These results were achieved by the use of the rock-dust cartridge method of stemming shots in the Ruhr coal mines, as announced by Dr. Alfred Stettbacher in the September 1923 number of the Explosive Engineer. Immediately, the explosive and the coal-mining industries on this continent became intensely interested. Considerable experimental work has been carried on in a number of American and Canadian mines during the past year, by which our engineers have become assured that the use of rock-dust cart-ridges for stemming shots increases the efficiency of explosives and promotes safety in coal mines.

Jan 1, 1924

By W. R. Dodge

THE growth and development of the assay department of the Hollinger Consolidated Gold Mines, Limited, is a similar story to that of the mine itself. As the mine developed and enlarged, so also increased the demands upon this department, necessitating an increase of capacity for fire assaying and a widening of the scope of work to include chemical analysis, metallurgical tests, research, and screen analysis. The yearly total of determinations, taking an average for the past six years, is approximately 350,000. The major portion of this figure represents fire assaying for gold and silver, being approximately 950 fire assays per day. The assay department occupies the ground floor of the administration building and covers approximately 4,000 square feet of floor space. Ready access is had by motor truck and electric railway for the delivery of samples and the removal of crushed rock and rubbish. The combined weight of all sample rejects amounts to about 5,000 lb. per day, which is sent to the mill bins. There are six departments, each occupying a separate room-grinder room, fluxing room, furnace room, parting room, weighing room, and flux-mixing and storage room.

Jan 1, 1931

Overview of Presentation ?About MiHR ?Human Resources Challenges in the Minerals and Metals Industry ?Getting the Facts -Sector Study Project ?Key Findings ?Recommendations ?Conclusions ?MiHR?srole

May 1, 2006

"Since World War II, urban communities have expanded at an unprecedented rate. The industrial mineral industry supplies the sand, grave], limestone, crushed rock, cement, gyp-sum, etc. for urbanization. Most de-posits in use are close to or within communities. Pollution of water and air has become a matter of public concern. Waste disposal and the effects of noise and vibration are subjects of public debate. Need for the reclamation of land after operations such as strip mining is discussed in magazine articles and on TV pro-grams; i.e., the general public is educated in the unattractive features of mining.Legislation is on the books and being drafted to regulate mining operations and their side effects. To avoid over-regulation and restrictive legislation, it is necessary that the public be educated and legislators informed of problems peculiar to the mining industry. Our side of the story needs publicity."

Jan 1, 1968

By Donald J. MacNeil

The commercial carbonate industry of Cape Breton Island, Nova Scotia, began about eighty years ago with the opening of the Sydney steel plant. Significant carbonate deposits are confined to the Precambrian George River Grav" and the Mississippian Windsor Group. George River Group carbonates are thought to have formed as part of a stable platformal sequence. They are crystalline and lie within a dominantly quartzitic sequence. Of the four major sites for George River carbonates on the island, the most commercially promising are the dolomite at Kelly Cove and the limestone and dolomite at Glencoe. Kelly Cove dolomite has good potential for metallurgical, agricultural and fettling purposes; reserves approach 13.6 million tonnes. Windsor Group carbonates were deposited as marine sediments in basins formed by pre-Carboniferous fault blocks. Windsor dolomite reserves at Stoney Creek are only fractionally retrievable and hence are of little economic value. The Windsor Group's Irish Cove limestone has been quarried on a large scale since 1964; no undeveloped commercial deposits, however, remain in the group.

Jan 1, 1984

By S. Kodama, G. Sasaki, K. Matsugi, K. Sugio, Y. B. Choi

"Pure aluminum (Al) matrix composites with changing the volume fraction of TiB2 particle content from 10 to 30% was fabricated by spark plasma sintering (SPS) process. Then the microstructure, density, dispersibility and thermal conductivity of the composites was estimated. As increasing TiB2 content, the dispersibility of particles and the density of the composites degraded slightly. And, the effect of the dispersibility of TiB2 particles on the thermal conductivity was quite little. The thermal conductivity of the composites was less than the theoretical value calculated by Maxwell-Eucken equation considering the effect of the density. It is due the influence of the interface heat transfer rate, because these composites have many small sized particles and have high interface density.INTRODUCTION Recently, metal matrix composites (MMCs) have been used widely in electric / electronic components, architectural materials, transportation equipment, aerospace and a precision instruments, because it’s superior properties have been greatly watched. Demand of MMC for industrial use has been increasing gradually. Furthermore, multifunction properties are required for the composites strongly. By integrating the dissimilar materials, the composites have various properties that we cannot get from monolithic materials. On the other hand, the response to the thermal management is required for materials, recently, and the need for the structural material controlling the thermal conductivity has been increasing. Especially, superior thermal conductivity and good mechanical properties from room temperature to high temperature are required for heat sink and heat exchanger at the same time. In late years, a study on the composites combining carbon materials and aluminum and copper has been developing, and actually the composites with high thermal conductivity which is not provided in the conventional materials is developed. On the other hand, non-oxide ceramics particles such as SiC and AlN, TiB2 have good thermal conductivity. Particularly, as TiB2 has good electrical conductivity, TiB2 containing MMCs is expected as innovative materials used as electric/ electronic components. Furthermore, as TiB2 has low density, high melting point, low thermal expansion and good deformation resistance, the development of high performance composites with multi-functional properties is expected. As thermal conductivity of pure Al and TiB2 are 225 and 66.4 W/mK, respectively, it is expected that the degradation of thermal conductivity by adding dispersant in Al matrix is suppressed. The authors have carried out a thermal conductivity, electrical conductivity, mechanical properties of 20 vol.% TiB2 dispersed Al composites (Sugio, 2016, Sasaki, 2016). In this study, the influence of quantity of addition of TiB2 on microstructure, thermal conductivity was studied minutely."

Jan 1, 2018

By I. Spector, A. J. Smith

In 1967, BACM Industries Limited started producing walboard at Saskatchewan's first gypsum products plant, located in Saskatoon, using, as a basic raw material, gyp-sum rock supplied from the company's mine near Amaranth, Manitoba. This paper describes the geology of the Amaranth gypsum deposit, the method of mining the rock and the manufacturing facilities used to produce wall-board.

Jan 1, 1970

By J. Ipinza, J. P. Ibáñez, Casas J., S. Cortés

Copper powder generated during the treatment of electro-metallurgical bleeds by reactive electro- dialysis (RED) had totally reduced the content of ferric ions in acidic synthetic electrolytes (Cu (II)- Fe (III) – H2SO4). In batch and columnar experiments 100% of the ferric ions were reduced to ferrous ions with an extremely high kinetics. A preliminary conceptual design for reducing ferric ions based on an integrate RED- Column for treatment of electro-winning bleed system is discussed. This system is able to recover simultaneously sulfuric acid and copper powder, which will reduce ferric ions. INTRODUCTION It is well known the negative effect of ferric ions in the copper electro-winning process. The increase of ferric content in the electrolyte reduces the current efficiency, i.e., there is an increase in the energy consumption, and changes the surface morphology of the copper deposit (Das, Gopala & Krishna, 1996; Vargas & Parra, 2013). The increase of the specific energy consumption due to the loss of current efficiency occurs by the reduction reaction of ferric to ferrous ions in the cathode, at the anode the ferrous ions are slowly oxidized to ferric ions (Shaw, Dreisinger, Lancaster, Richmond & Tomlinson, 2004). To control the level of iron in the electrolyte, bleeds are needed; this bleed electrolyte containing copper, sulfuric acid, cobalt, iron and other impurities normally is waster, which increased the production cost of the plant (Milbourne, 2002; Mckevitt & Dreisinger, 2009). Then, permanent efforts oriented to treat those bleeds to avoid losses of valuables components are made; among them are use ion exchange resins (Shaw et al., 2004; Mackevitt et al., 2009), chemical precipitation (Izadi, Mohebbi, Amiri & Izadi, 2017) and electrodialysis (Cortés, Ipinza & Ibáñez, 2013). The last one allows to the simultaneous recovery of sulfuric acid and copper powder. If one of the valuables obtained by treating the bleed can be used to reduce ferric ion concentration in the electrolyte could be an important asset. This issue at laboratory scale is reported in this work, the use of copper powder, generated by reactive electro-dialysis when treating synthetic acidic electro-metallurgical bleeds, for reducing ferric ions in acidic electrolytes.

Jan 1, 2019

By R. E. Bou Serhal

Many miners are exposed to dangerously high levels of noise on a daily basis. Over the past 15 years, a continually increasing number of occupational hearing loss has been reported from the mining community in the United States, of which, more than 95% is attributed to prolonged noise exposure. Although the noise exposure levels may differ between coal miners and metal and non-metal miners, in the absence of noise control at the source, the solution is the same: use of personal hearing protection devices (HPD). While protecting the miners? hearing it is also essential to no longer hinder their ability to communicate. With access to an advanced HPD that is customized to the miners? ears we are able to combine these two requirements. Using an intra-aural instantly custom molded HPD miners are protected from high levels of noise. The HPD is equipped with wireless capabilities, and contains both a speaker and an In-Ear Microphone (IEM). Therefore, the miners? speech may be captured from inside the ear and transmitted to the remote listener. This IEM signal is relatively noise-free since it is isolated from the background noise. The IEM speech signal, however, is ?boomy? and is missing some high frequency content, making fricative consonants hard to understand. Nonetheless, the IEM speech signal is correlated with the natural speech signal and may be manipulated through statistical techniques to more closely resemble natural speech. By improving the intelligibility and quality of the IEM signal, numerous applications may be enabled. One use of the enhanced IEM signal will be for radio communication. Using wireless radio communication in a noisy mining environment is sometimes the only practical and affordable solution to allow communication between miners equipped with personal hearing protection devices. Traditionally, one of the weaknesses of such wireless radio communication lies in the lack of designating receivers: whether they are the intended receiver or not, all those carrying a radio receiver are subjected to the broadcasted signal. The current work will detail a new concept of a "radio-acoustical virtual environment" where the radio signal will only be received by miners within a given spatial range, such range depending on the user?s vocal effort as well as the ambient and perceived background noise levels.

Aug 1, 2013

By J. P. Messervey

As a result of my field examinations in this Province, I have been struck by the evidence of widespread mineralization in rocks, particularly the limestones of Carboniferous age. Six prospects of lead and zinc or lead alone scattered through the eastern part of the mainland, one copper prospect and three veins of siderite, all point to a period of mineralization subsequent to the forming of the Carboniferous rocks in which they occur. While none of the present prospects are of proved economic importance, still it is possible, and indeed probable, that further prospecting will find concentrations sufficiently large to make mines. It may possibly aid the prospecting for these base metals if the present scraps of information are assembled from various sources, and I will further briefly recount the information as a result of my observations. Gay?s River At Gay's river, midway between Halifax and Truro, and four miles east of the railway, numerous pits and natural exposures show galena and sphalerite in limestone of Carboniferous age, near where it lies unconformably upon slate and quartzite of the gold series. These exposures extend for a length of over one thousand feet along a curving contact. The pits show that on the contact there is a fossiliferous and somewhat porous layer of limestone, which is so impregnated with galena and small amounts of sphalerite as to be of ore grade. Wherever observed, the thickness of this layer is less than two feet.

Jan 1, 1929

By J. W. Reynolds

This paper describes the function of the research and development department of a large mining organization and the benefits which can be derived over the years. Examples are given of work done in rock drilling, ventilation, noise control and the development of backfill stowing machinery.

Jan 1, 1970

By C. Lapointe

"IntroductionTen years ago, when nuclear fission became practical, the element uranium, until then a not very desirable by-.product of the radium industry, became overnight the strategic material par excellence. One of the several important problems that had to be solved at that time was the rapid and precise determination of uranium in ores and concentrates.GeneralThe chemical analysis of uranium ores is a long and difficult business and is complicated by the presence in most ores of a large number of interfering elements. True, much progress has been made, during the past few years, toward simplification of the analytical methods, but the chemical determination still remains the job of a skilled operator. For this reason, the chemical method has been replaced, whenever possible, by a physical determination based on the measurement of the radiations emitted by the elements of the uranium family. There are several types of instruments suitable for these measurements, but of all the radiation detectors known to the physicist, such as ionization chambers, crystal detectors, scintillation, proportional counters, and the like, the Geiger-Mueller counters have proved to be the most satisfactory for routine determinations, because of their simplicity.The Geiger-Mueller counter is a very versatile instrument; it can be constructed to detect any type of radiation, corpuscular -0r electromagnetic. Here, however, we are interested in these counters because of their ability to detect the beta and the gamma radiations, both emitted by some members of the uranium family. The beta radiation is corpuscular, and is composed of fast electrons, while the gamma radiation is electromagnetic."

Jan 1, 1950

By W. R. Bacon

"MAGNETITE HAS BEEN found in many .parts of the coastal area of British Columbia, but the more important deposits are on Vancouver Island and Texada Island. The locations of these deposits are shown on Figure 1.Interest in the magnetite deposits dates back to the 1870s, when land was acquired on the southwest coast of Texada Island by the Puget Sound Iron Company. This ground included the Prescott, Paxton, and Lake deposits. During the years 1885 to 1903, and 1908, 28,898 tons of magnetite ore was shipped to the company's blast-furnace plant at Irondale, Washington, U.S.A. This production was almost entirely from the Prescott open-pits.In the years following the Texada Island discoveries, other magnetite deposits were found in the coastal area, and various plans were proposed to utilize the local ores in the establishment of a steel industry in the Pacific Northwest. None was carried to fruition but, in 1951, open-pit mining was begun at Iron Hill, Vancouver Island, to furnish iron concentrates for steel mills in Japan. In 1952 mining of the Texada deposits was resumed to supply the same market. Production figures for these recent operations are as follows:"

Jan 1, 1949