Search Documents

By N Berkowitz

Slurry pipelining, as now under-stood and practised, can only command marginal interest in Canada, as long-distance railway freight charges in this country are generally lower than slurry pipeline tariffs. Several alternatives to conventional slurry transmission are, however, now emerging, and two such alternatives are briefly discussed with reference to coal pipelining. In one, coal is transported as a suspension in oil; the other contemplates the movement of paste "slugs." Preliminary economic estimates indicate that the resulant process simplification and adoption of common carrier principles could lead to cost reductions that might make Western coal competitive with imported fuel in the power generating stations of eastern Canada. R ECENT appraisals of slurry pipelining techniques, some-what incongruously 'based upon the performance of successful installations (1,2), are making it increasingly apparent that current solids pipelining methods can only command marginal interest as methods of bulk commodity transportation (3). Although some uncertainties remain in matters of detail, it is now generally conceded that long-distance slurry pipelining cannot compete against rationalized railway transportation unless movement of

Jan 1, 1963

By R. J. R. Schaller

NO. 3 winze, the sixth shaft to be sunk on the San Antonio property, is practically a duplicate of No. 3 shaft, which was the main shaft prior to the installation of the larger hoisting equipment in 1939. It is collared on the tenth, or 1,500-ft., level, and goes down vertically to the sixteenth, or 2,500-ft., level, with a loading pocket, spill pocket, and sump below this. It is 1,000 feet east of No. 3 shaft. All ore, men, and materials are handled through the latter. The winze location with reference to the rock formation is shown in Figure 1. (In plan, this section strikes N.30°E. and cuts most of the main orebodies of the mine normal to their strike.) It is collared eighty feet inside the footwall contact of the basalt and cuts through it before reaching the eleventh level. In this location there will be no ore tied up in shaft pillars, as the closest ore to the shaft is on the tenth level, and here it is eighty feet northeast of the collar. The winze headframe and hoist-room straddle the main haulage to the No. 3 shaft, on the tenth level (see Figure 2). At no time during the excavation for the headframe and hoist-room was the general routine work of this haulage held up.

Jan 1, 1941

By Yujing Jiang, Xuezhen Wu, Bo Li, Tomomi Iura, Gang Wang

"Yielding bolt has been widely used for rock reinforcement in mining and civil engineering in high stress conditions. However, the interaction mechanism of yielding bolt and matrix mass is still not clear at present, and no analytical model is available to predict its reinforcement effect quantitatively. In this paper, the mainstream yielding rock bolts were reviewed firstly. After that, a coupling model is proposed to account for the interaction between yielding bolt and matrix mass. Based on the plane strain axial symmetry assumption and the incremental theory of plasticity, equilibrium equations and compatibility equations of matrix mass, and also the response of yielding rock bolt are deduced theoretically. The proposed method was programmed in Visual Basic development environment, and a semi-analytical solution for the coupling model is achieved. The reinforcement mechanism of yielding bolt in conventional tunnelling is clearly demonstrated through an illustrative case study. The reinforcement effect of yielding bolt is estimated quantitatively, and the distribution of axial force along the bolt is presented. In addition, the validity of proposed method is verified by numerical simulations. INTRODUCTIONHigh stress in surrounding rock mass can cause serious stability problems such as massive squeezing in soft rock and rock burst in hard rock. It is observed that many conventional rock bolts failed when experiencing large displacement, which implies that they are too stiff to sustain large deformation and dynamic conditions (Stillborg, 1994; Hoek et al., 1995). Yielding bolt, which can also be called energy-absorbing bolt, has been widely used for rock reinforcement in mining and civil engineering for these conditions (Neugebauer, E., 2008). This paper focuses on the static reinforcement effects of the yielding bolts with analytical method and numerical simulations."

Jan 1, 2015

By C. Kunze

ABSTRACT Although closure sureties cover works that are carried out during the existence of a mining company, certain liabilities are not known when the surety is established and become apparent only in a late stage of the closure phase, or even after the site has been relinquished. This paper supports the concept that these financial risks lend themselves to insurance solutions. Making insurance for unknown liabilities mandatory while defining unambiguous legal conditions could create a viable market for insurance products, provide a sufficient statistical basis for the calculation of premiums, and reduce costs.

Jan 1, 2013

By C. A. Campbell

"There has been a significant reduction in maintenance hours and improved performance by maintenance crews at the MacLeod mine since the introduction of a Maintenance Control system which includes the use of maintenance standards. This paper deals with the steps taken to develop and implement the program. The objectives of the program and the organization and training of the control group are outlined. The work-order system, standards application, classification of work and the preventive maintenance procedures will be discussed.All maintenance information is processed on a Model 360-20 IBM computer, which turns out maintenance records and control reports for management action. Information in these reports, and reasons for reporting, will be discussed and the benefits resulting from the program reviewed."

Jan 1, 1973

By Wei Wang

The SMCO copper plant is located in DR Congo, and was designed by China NERIN Engineering Co., Ltd. The process is a typical hydrometallurgical plant with Leach-SX-EW, with the project treating the oxide minerals with agitation leaching, followed with three stage of solvent extraction and two stages of stripping, and using permanent SS cathodes to produce LME grade copper. Because of the special characteristic of the ore, what contains 2 different type of oxides (one high carbonate oxide and the other low carbonate), there are several new technical measures that have been developed and adopted for the plant. For example, different grinding, leaching, and filtering are used to treat different oxides. This paper, presents the project process, engineering design, construction and commissioning. The paper also describes some of the problems encountered during plant commissioning, such as the agitation leaching tank issues, and corrosion in the settler-mixer. This paper discusses some NERIN solutions to these problems, and explains the use of the CN filter, which is used to filter PLS to treat high level suspend solids, instead of the traditional sand filter. Finally, this paper also proposes steps / measures for further improvement for future plant operation.

Jan 1, 2014

By W. B. Coker

A helicopter-mounted lake-sediment and lake-water survey was carried out over Grenville rooks in the Renfrew area (parts of Renfrew and Lanark counties) during four days of October, 1975. In the course of this survey. 1150 square kilometers were covered, with 246 lake-sediment and 276 lake -water samples collected from every body of water on which the helicopter could land. Sample sites, which averaged one per 4.6 square kilometers, included lakes, ponds, beaver ponds, swamps and marshes. Lake-sediment samples were taken using a G.S.C. sampler. Waters were collected directly into polyethylene bottles. At each sample site , surface and bottom-water pH, dissolved oxygen content, conductivity and temperature were measured using a Martel. Water Quality Analyzer. The lake sediments were air dried and then ball milled to pass a minus 80-mesh sieve. Lake sediments were analyzed for U by delayed neutron activation and for Mo, Cu, Zn, Pb, Fe, Mn, Ni and Co by atomic absorption techniques. The organic content of the sediments was determined by loss on ignition at 450 °C. Lake waters were acidified with nitric acid on the day of collection. The U content of the water s was determined by fluorometry; the Cu, Zn, Pb, Fe, Mn , Ni and Co contents of the waters were determined by solvent extraction - atomic absorption techniques. A close relationship was found between bodies of granitic, syenitic and pegmatitic bedrock and elevated U levels in the lake sediments. The Hurd Lake and White Lake granitic intrusive were encompassed by an annulus of higher U activity. Field inspection revealed that the U concentrations occur within a zone which may represent a contact metamorphic aureole. Within these complexes, anomalous concentrations of U appear to be associated with Mo. Information derived from the lake-water data reinforces the geochemical distributions outlined by the lake-sediment survey . This survey was carried out in order to develop optimum sampling and analytical procedures for geochemical reconnaissance of the Grenville Province that may be carried out under the auspices of the Uranium Reconnaissance Program.

Jan 1, 1977

By M. Tanaka, T. Oishi, K. Koyama, S. Alam

"A novel hydrometallurgical process for copper recovery from waste printed circuit boards has been proposed, which consists of selective leaching of copper metal as Cu(I) by Cu(II) in ammoniacal alkaline solution, purification, and electrowinning. The distinct feature of this process is much lower power consumption during the electrowinning than that during the conventional one from acidic copper sulfate media, because the deposition of copper metal from Cu(I) at the cathode and the oxidation of Cu(I) to Cu(II) at the anode take place in the present method. In the laboratory-scale tests using waste printed circuit boards, high purity copper which contains 1.1ppm of impurities was obtained in a chloride system. INTRODUCTIONThe recovery of various metals from waste materials is an important issue in order to conserve the environment and metal resources. Copper is used for cables, electric appliances, etc., and is currently a very important material for industries and will continue to be in the future. Among the wastes that contain copper, one of the most complex recycling materials is electronic scrap like printed circuit boards (PCB), which generally contain 10-30% copper as well as plastics, fibreglass and other metals. There are two ways to recover copper, either pyrometallurgical or hydrometallurgical. Hydrometallurgical treatments generally have more flexibilities in the process scale and control. The separation processes tend to become complicated because of the poor selectivity during the leaching in the sulphuric and hydrochloric acid media. On the other hand, the use of ammonia as a complexing agent, gave a higher selectivity for copper leaching (Nigo, Majima, Hirato, Awakura, & Iwai, 1993; Majima, Nigo, Hirato, Awakura, & Iwai, 1993; Zhou, Shinme, & Anezaki, 1995; Koyama, Tanaka, & Lee, 2006) .In this study, recycling process containing leaching, copper deposition at a cathode and oxidation of copper(I) at an anode from ammoniacal alkaline solutions containing Cu(I) or Cu(II) is introduced. Furthermore, copper recovery from a waste printed circuit boards and impurity behaviour was examined in ammonia-ammonium sulfate (sulfate system) and ammonia-ammonium chloride (chloride system) systems."

Jan 1, 2012

By A. Zorkovská, S. Castro, P. Baláž, Z. Bujnáková

Enargite (Cu3AsS4) belongs among refractory copper minerals with very low hydrometallurgical extractability of copper. An application of enargite leaching in acid solutions leads to simultaneous dissolution of copper and arsenic and the final leach solutions have to be treated for the separation of both elements. However, the alkaline leaching of enargite is selective. Arsenic passes into leach while produced copper sulphide represents the raw material suitable for pyrometallurgy. The hydrometallurgical processing of mineral can be influenced positively by mechanochemical route. We have shown that more than 80 % of arsenic can be extracted from enargite concentrate by atmospheric alkaline leaching at 95 °C when mechanical activation in an attritor is applied. The produced Cu2S can be further treated with elemental iron where mechanochemical intervention is applied in the second stage of enargite processing. The final product forms Cu/FeS nanocomposite from which copper nanoparticles can be easily separated. The illustrated concept of copper obtaining from copper sulphide is an example of so-called “dry” processing, as reactions in gas and liquid phases are excluded. This concept of environmentally friendly metallurgical processing can be classified as an impetus for novel technology to produce copper from enargite concentrates.

Jan 1, 2012

By Zhiqiang Wang

This paper mainly focuses on the method of ?three-zone? definition (a caving zone, a fissure zone and a curve subsidence zone) for full height cutting in a thick seam. Based on criteria of a caving zone and a water conducting zone, as well as existing research achievements, it is believed that there exists great error for calculation of height of the ?three-zone? area using cutting height and the coefficient of bulk increase. Dynamic factors should be considered, so, based on the theory of key rock strata and combining this with several other factors, such as mining area, this paper presents a new method to determine the overburden ?three-zone? definition. The results are as follows: (1) geometric models of a working face and key stratum are established through the rock displacement angle, with consideration of the influence of mining on the key stratum (the range of key stratum influenced by mining is enlarged as the mining area increases); (2) because there is always a cavity below the key stratum of the thick coal seam with full seam cutting, and the key stratum gradually fracture with face advancing, based on the geometric dimension of strata, the maximum fracturing interval expression has been presented, including the working face advancing range. This can theoretically lead to the location of the key stratum influenced by mining, and its stability before mining, helps to confirm which zone the key stratum and following-up strata belong to, using the criteria of sliding instability or deformation instability; (3) the new method of ?three-zone? definition which is based on the theory of key rock strata is first proposed for full height cutting in thick seam. Finally, combined with practical engineering, and comparing with field data, it is believed that the proposed method is more objective than existing methods.

Aug 1, 2013

By Jianwen Yang, Yucai Zhou, Yanhong Dong, Daixiong Chen

"The study of combined depressants for flotation separation of lead from copper has been carried out to solve the copper-lead separation problem. Test results show that the depressant of CMC (Carboxyl Methyl Cellulose) or sodium sulfite plays an important role on the selective depression of galena flotation. When the two reagents above are combined, the selective depression effect on galena is further enhanced. When the mass ratio of CMC to sodium sulfite is 1:4, galena was best depressed, with the lowest lead content in the copper concentrateClosed-circuit tests indicate that under a certain pH value of the slurry, with the best ratio of CMC to sodium sulfite as depressants, the copper concentrate with the grade of 28.23% copper and 4.12% lead is obtained, and the copper recovery is 84.87%; the lead concentrate with 68.12% lead and 0.86% copper is obtained, and the lead recovery reaches to 92.20%. An efficient separation of copper and lead is achieved with the combined depressants. INTRODUCTIONComplex copper-lead-zinc sulfide ore is abundant in China. With the rapid increase of mineral consumption, it has become one of the important sources to produce copper-lead-zinc metals. However, it is difficult to achieve effective separation of copper and lead, due to the complicated ore properties, such as fine dissemination, low copper grade, complex symbiotic relationship and similar floatability of copper and lead.Poisonous reagents of bichromate and cyanide are often used as depressants for copper lead separation. They have good separation efficiency, but pose serious pollution issues. As the environmental protection is becoming more and more important, it is a trend to replace traditional toxic reagents with new nontoxic efficient chemicals. Organic depressant FCLS studied by Liu has strong selectivity against galena, and does not depress chalcopyrite. A new type of galena depressant of CLS-01 discovered by Jin-lin Yang shows good results in the separation a mixed copper and lead concentrate. In addition, dextrin, chitosan and some other natural organic compounds (Drzymala, 2003; Huang, 2012; Qin, 2013) have also been studied to separate copper and lead."

Jan 1, 2016

The process of gold recovery by gravity concentration is incorporated in the metal recovery flowsheet at seven Newmont Mining Corporation owned mining operations in Australia, North America and Africa. In 2009 gold recovered by gravity processing was equivalent to nine percent of Newmont's total gold sales of 5.3 million ounces. This paper will discuss these applications in detail including a review of plant flowsheets and presentation of recent operating results. Operating performance will be discussed with reference to ore characterisation procedures, interpretation of results, design considerations and optimisation practices as they relate to the recovery of gold by gravity concentration.

Jan 1, 2011

By N. C. Karmakar, Y. V. Rao, M. Aruna

No one can properly work without sufficient light and this is especially so in mines where conditions are difficult. Artificial lighting is very important for the night shift to provide a safe and efficient working environment, which must be evenly illuminated with no obvious dark spaces and a minimum amount of glare. During an illumination survey of a large mechanized surface mine, it was found that the illumination level varied and was not uniform throughout the length of the road; it was high at one side of the road instead of at the centre. There were also different combinations of lamps, with angles of light arm varying from 35º to 70º. In this respect, an experimental study was carried out with a fabricated telescopic light pole to uncover the optimum design parameters of lighting installations. The analysis was done by plotting isolux contours for fixed installations and drawing graphs for various combinations of luminaries, reflectors, light arm angles, and height of lanterns by plotting the horizontal angle of the light arm along the abscissa, and the contour area along the ordinate. The study revealed that the design parameters of the lantern are mainly dependent on the type of luminaires. It was revealed that the pot reflector with a combination of tubular bulbs produces a wide distribution of light, and contributes towards a reduction of luminaries when installed in longer roads.

Jan 1, 2005

"Projections of demand for Alberta coal indicate a quadrupling of current production rates to some 70 million tonnes/year by the end of the century. About half of this output-comprised of subbituminous coal-will be required within the province, primarily for generation of electric energy. The remainder-roughly 70 per cent high-volatile bituminous (hvb) steam coal and 30 per cent medium- or low-volatile bituminous (mvb/lvb) metallurgical coal-will be exported, principally to Pacific Rim and Western European countries. Direct employment in mining and coal processing is projected to increase from the present ca. 3000 to at least 12,000 persons.This paper presents separate forecasts for subbituminous, hvb and mvb/lvb coal production in the period 1982-2000; notes a number of possible developments that could substantially modify these forecasts; and briefly discusses attendant infrastructure requirements. Attention is drawn to potential shortages of qualified manpower and to threatening inadequacies of transportation facilities.IntroductionDespite the dislocations triggered by the 1973 'oil crisis', energy budgets of Western industrial countries are mostly still in the very early stages of the anticipated transition to greater reliance on coal. Shift s to coal are still more often only talked about than being implemented; and the public policies which are essential for timely development of facilities for producing, transporting and using coal are in many instances not yet even broadly formulated, let alone enunciated.In these circumstances, long-range projections of coal demand and supply-even if restricted to internal requirements- are subject to greater uncertainties than usually afflict such forecasts.On the demand side of the equation, these uncertainties arise ultimately from linkages between a need for coal and the availability and pricing of OPEC oil. The current surplus of oil on world markets, which has recently forced substantial reductions of posted prices, is undoubtedly a transient phenomenon that is unlikely to have any long-term impact."

Jan 1, 1982

By I. Kirman, B. Waters

World wide applications for nickel use will be summarized and examples of those uses given. Nickel products are critical to many important aspects of modern society. These products are just as important for modern China as they are in other parts of the world. It is argued that future pattern of nickel use in China should be expected to be very similar to that in the rest of the developed world. Total use of nickel in products in China is already very large. In 2004, it was the largest market for stainless steel (nickel containing) in the world. A survey of Chinese stainless steel applications will be presented. Current high nickel prices have revived speculation about substitution, particularly for nickel containing stainless steels. The presentation will discuss some of the complicating factors that need to be taken into account when considering substitution. These factors are as valid in modern China as they are in other developed economies. Recent substitution efforts and the reaction to them will be examined. The Nickel Institute position regarding appropriate application of the various grades of stainless steel will be discussed. Price-motivated substitution in China, and elsewhere, will occur but it is argued that the extent will probably be limited.

Jan 1, 2005

By H. W. Wevers

Fatigue failure and accompanying brittle failure occurs frequently in heavy mining equipment. This paper discusses how fracture mechanics can be applied as a tool for crack control and crack management. Information is provided to determine if particular components are prone to brittle failure. By using existing fracture mechanics formulae, an estimation of the critical crack size can then be made. It is explained that for a successful application of fracture mechanics, both the actual engineering stress in the component and the mechanical properties of the applied material must be known. The importance of toughness at low temperatures is quantitatively illustrated by calculating critical crack sizes at room temperature and at below-zero temperatures. Understanding the possibilities of fracture mechanics will also produce a climate in which the purchaser of equipment can more precisely analyze the relative quality of components with respect to crack tolerance and failure prevention. In this manner, communication between the user and manufacturer of equipment may also become more precise and effective, leading to improved design.

Jan 1, 1977

By J. A. Finch

In this paper, the author offers a personal view of what the next 30 years holds for mineral processing. Restating that mineral processing will remain a vibrant industry in raw material production, growth opportunities in waste management are identified. The processing sequence familiar now (mining ?mineral processing ?extraction) will become more interwoven. In situ processing (i.e., milling underground) will evolve from concept to demonstration. Opportunities to exploit physical properties altered in chemical (pyro- and hydro-) processing will present themselves. In primary grinding, the path to AG/SAG milling will progress with little deviation but opportunities in regrinding are wide open. Flotation will see the trend to designing bubble/particle reactors accelerate simultaneously with a vigorous response from mechanical cell suppliers. Gravity separation remains a bastion of the lone inventor but this author anticipates that the new lines will come from the waste management business. The paper concludes with the examination of the “research cycle” and identification of growth in small “high tech” companies and university research centres

Jan 1, 1998

By P. J. Routledge

THE purpose of this paper is to discuss the practical aspects of locating gravel deposits and of establishing efficient, portable concrete aggregate beneficiation plants for use on construction projects where limited amounts of high-quality gravel and sand are required. Certain projects are listed, in order to demonstrate the wide variety of problems encountered. Routledge Gravel Contractors Limited, North Vancouver, have supplied concrete aggregate for construction projects in British Colum-bia since 1957. In tl1at year, in sup-plying aggregate for a small project at a site on the northern coast of British Columbia, our quote was as follows: Concrete aggregate to specifications, f.o.b. scow, North Vancouver$ 1.75 per cu. yd. Scowing charges to site. $16.00 per cu. yd. At that time, our company realized that more attractive quotations could be submitted if local gravel was utilized where available. Port-able equipment was then acquired and a simple screening plant (Figures 1 and 1a) was at first used. This was later replaced by heavier, more versatile equipment. The use of suitable equipment, the keeping of cartage to a mini-

Jan 1, 1962

By N. A. Beier, R. Amos, Smith. L., C. Atherton, D. R. Barsi, D. Blowes, D. C. Sego

"Waste rock is one of the most abundant materials at mine sites and must be properly characterized and managed to limit acid rock drainage and other harmful byproducts. An experimental waste rock pile—part of the test piles research program—located at the Diavik diamond mine (Northwest Territories, Canada) was deconstructed and sampled to study the spatial variability of material properties. Bulk samples were classified based on the amount of material finer than 4.75 mm. Hydraulic properties of each sample were estimated and particle size distribution analysis was completed. These datasets and classification methods might be used to improve the understanding of hydraulic and geochemical behaviour of the material and to study waste rock at other sites. ¦ KEYWORDS Acid rock drainage (ARD), Material classification, Particle size distribution (PSD), Waste rock RÉSUMÉ Les stériles font partie des matériaux les plus abondants sur les sites miniers et, en tant que tels, doivent être correctement caractérisés et gérés afin de limiter le drainage rocheux acide (DRA) et la pré¬sence d’autres sous-produits nocifs. Dans le cadre du programme Test Piles Research Program, un amas de roches stériles expérimental situé à la mine de diamant Diavik (Territoires du Nord-Ouest, Canada) a été décomposé et mis à l’essai afin d’étudier la variabilité spatiale des propriétés des matériaux. Les échan¬tillons en vrac ont été classés en fonction de la quantité de matériaux plus fins que 4,75 mm. Les propriétés hydrauliques de chaque échantillon ont été estimées et l’analyse de la composition granulométrique effectuée. Ces ensembles de données et méthodes de classement serviront à mieux comprendre le com¬portement hydraulique et géochimique du matériau et à étudier les stériles sur d’autres sites. ¦ MOTS CLÉS classement des matériaux, composition granulométrique, drainage rocheux acide (DRA), stérilesINTRODUCTION Statement of problem The characterization of mine waste rock remains a challenge in active mining sites. The large volume of material and the large size of particles make it difficult to collect representative samples. Sampling techniques are often dis-ruptive to mining operations because they alter the structure of the waste rock pile or interfere with mine traffic. The convention at most mine sites to collect little to no information on waste rock material means that models and predictions of how waste material will behave and interact with the surrounding environment are based on general information that might not be site specific. This could lead to environmental damage or higher costs if environmental effects are underestimated during the construction of waste rock structures."

Jan 1, 2019

By K. M. Murphy, M. B. Wittrup

ABSTRACT The Saskatchewan Ministry of Environment recognizes the importance of environmental protection as an important contributor to Saskatchewan’s economy, with the environmental performance of industry closely monitored. Unfortunately, environmental regulation is often accompanied by significant process that does not always add value to environmental protection activities. The Saskatchewan Ministry of Environment has embarked on a visionary restructuring of its regulatory framework from conventional command and control regulation to a results-based regulatory framework. This new regulatory framework will provide for establishing clear environmental protection and resource management objectives; streamlining the environmental acts and regulations; developing an environmental code of practice; relying on qualified persons; enhancing compliance and enforcement tools; eliminating of many permits; and developing greater certainty in environmental assessment decisions. Results-based regulation promises to deliver enhanced environmental protection with less process. The uranium industry in Saskatchewan will be used as an example of the potential effects of results-based regulation.

Jan 1, 2012