Search Documents

By Rashkovski GB

Until recently amalgamation has been the main process forextracting large gold particles from gravity concentrates obtainedduring the dressing of ores and placer gold deposits.Development of new technology for treating the gravityconcentrates was necessary because of the harmful effect ofmercury on subsequent production processes and theenvironment. The harmful effect of mercury is particularlyevident in the resin-in-pulp process that is widely applied inRussia.

Jan 1, 1993

By Saghafi A, Kelly M, Williams R. J

A two year program of research into the feasibility of long-hole drilling for improved gas emission control has been undertaken at Appin Colliery. State of the art equipment was employed involving cableless electronic surveying and down-hole motor drilling. The project involved the drilling of 1000 m long, in-seam boreholes in the Bulli seam and boreholes of similar length drilled cross measure and then in-seam along the underlying Balgownie seam. A new concept for gas drainage was defined, employing long-holes for both predrainage and post drainage.

Jan 1, 1988

By R Farana

The future challenges in mining instrumentation, mainly on future intelligent mines, are to continue providing instruments with the highest level of reliability at the lowest possible cost, and also to take advantage of technology existing in other industries and to adapt it to the mining context. New wireless instruments (smart sensors, smart actuators, smart controllers) would also be very useful, as well as instruments fully adapted to the monitoring of large movements that are observed, in both underground and open pit mines. Mining instrumentation is found to various degrees in most mines, both open pit and underground. Smart mining instruments present a certain number of aspects specific to the environment in which the instruments are installed. Namely, the instruments can be installed either for short-term or long-term purposes. The mining industry is always looking for useful instruments that can provide relevant information on ground behaviour adjacent to mining stopes or permanent infrastructure. The instruments must meet the various criteria, and must also evolve with the new mining technologies that are continuously being implemented. A strong collaboration between the mining industry, research organisations, and instrument manufacturers is the key to meeting these objectives. This contribution describes the current trends on smart sensors and smart instrumentation with Wireless LAN support.

Jan 1, 2003

By F Anthes, U Barow

Two tunnels are being bored using a æHydroshieldÆ in section 3.1 of the extension of the Underground railway line 5. At the end of the two tunnels, directly in front of the Hotel Adlon, the shields cannot be retrieved. The steel shell of the shield will be left in place within a sealed concrete block and the reusable components taken out through the completed tunnel. For the first time in Germany, an Underground tunnel is being lined solely by means of UNI rings. BerlinÆs Underground network is 165 km long and has 167 stations. Some 450 million passengers are transported annually. On account of the urban planning modifications that followed reunification, the network has to be adjusted, particularly in the city centre. The most significant project is the extension of the U5 from Alexanderplatz to the Lehrter Bahnhof. After completion, the U5 will be a continuous east-west traffic artery. It will provide a direct link with the new parliamentary and government district, open up new business districts and the cultural centre of the city.

Jan 1, 1999

Introduction The mine winder is an essential element in the mining of ore in deep level mines and therefore requires a high degree of reliability to avoid interruption of production. Failure of any component on a winder may also be dangerous and expensive to repair. The larger the failure the larger the stoppage. The failure of a winder drum is the ultimate catastrophe, not only because of the cost of replacement, but also because of the lead time in procuring a new drum. Today these types of failure are not as common but many failures have occurred in the past and even today many an old winder is con- sidered for a new and often more arduous duty. As far back as the turn of the century a lot of information had been gathered to try and clear up the complexities of the multi- layering effect of coiling rope under tension onto a drum. Before comparing results obtained by various researchers the nature of the pressure distribution between rope and drum due to multi-layering will be discussed briefly.

Jan 1, 1987

By Martins V, Dunne R

A re-evaluation of the Hampton Boulder prospect in the early eighties resulted in a decision to proceed with mine development in December 1985. A 500 000 tpa gold treatment plant was commissioned in December 1986. The treatment facility was expanded to 1 600 000 tpa in July 1988. A tailings treatment plant to improve recoveries from harder gold bearing sulphide ores was built in December 1990. The development of an underground mine in 1991 meant that a source of sand for backfill was required. A sands plant to fulfil this requirement was commissioned during November 1991.As of June 1992 a total of 7 710 487 tonnes of ore have been treated through the New Celebration gold plant. Total gold production from inception of the new mine until June 1992 is 545 470 ounces obtained at an average recovery of 90.1 per cent from an average gold head grade of 2.4 g/t. The combined quoted ore reserves at the end of December 1991 was 14Mt grading 1.8 g/t gold

Jan 1, 1992

Detailed cash flow forecasts have always been almost essential as a basis for judging the viability of proposed new mining projects. In recent years attempts have been made explicitly to take account, in such forecasts, of the uncertainties surrounding the assumptions upon which they are based. With the risk analysis approach, Monte Carlo simulation of the cash flows indicates in probability terms the combined effect of these uncertain basic assumptions. While the use of risk analysis has been widely discussed, few specific applications to real projects have been reported. The application of such an analysis in the feasibility study of the large new Deelkraal gold mine presently being established on the Far West Witwatersrand gold fields by the Gold Fields Group in South Africa is described in the paper. The paper also indicates how one of the major sources of uncertainty, namely the gold content of the ore, can be`quantified in objective probability terms. This feature distinguishes the application fran other published accounts in which only subjective probability assessments have been utilised.

Jan 1, 1977

By M Dixon, T OÆShannessy

Melbourne Water (MW) is responsible for a section of existing gravity trunk sewer servicing the Melbourne central business district, Docklands, Port Melbourne and other adjacent areas, known as the Melbourne Main Sewer (MMS). MW has determined that the 2.2 km long 110 year old sewer will not adequately service these areas into the future or provide the level of reliability needed. The Melbourne Main Sewer Replacement project (MMSR) involves the replacement of the MMS with a new gravity sewer main and six key manhole shafts, known as the Melbourne Main Reliever (MMR).The majority of the MMR sewer tunnel is situated south of the Yarra River and will be constructed using an earth pressure balance (EPB) tunnel boring machine (TBM) and will be lined with precast concrete segments. The tunnel will be 2.4 m internal diameter and will have a 1.8 m diameter glass fibre reinforced plastic (GRP) sewer pipe positioned within it. This project represents the first large-scale, modern, mechanised tunnel project in MelbourneÆs Yarra Delta Quaternary sediments. There is little precedence known to the authors of similar scale tunnelling projects in these particular geological units. During the recent detailed investigation and design stages of the project, significant effort has been spent on characterising the geotechnical conditions along the alignment and predicting the effects of the new tunnel on the existing environment. Some of the key design issues that have been identified and managed through the design process include short-term surface settlement due to tunnel excavation and the predicted effects on surface infrastructure, potential spalling of the steel fibre reinforced concrete segments under full TBM ram loads and tunnel lining design in geological units with highly variable stiffness.Construction of the new MMR sewer tunnel is expected to commence in mid-2008 with a capital cost of approximately $160 million. Sewer system commissioning is scheduled for completion by early 2012.

Jan 1, 2008

The Golden Cross is the first large precious metals mine to be both commissioned and closed in the æmodernÆ era in New Zealand. This paper discusses the life cycle of the Golden Cross mine, with emphasis on the closure process and post closure management.   The closure process has generally been very well managed, and successful, but in spite of that some on-going issues remain unresolved. Nearly nine years after the end of mining the mine owners are still actively managing the site, with no immediate end to that in sight.   The site has been described as atypical, due to the identification of a deep seated landslide below the tailings and waste rock storage facilities. However that should not be given too much emphasis when addressing the overall closure and post-closure management issues, which could well apply to other existing and future mine sites in New Zealand.   The Golden Cross can provide valuable lessons for other miners, and the issues arising at this site should be watched closely by the industry as a whole.

Jan 1, 2006

By S Walters

The emerging discipline of ‘geometallurgy’ is not new but is becoming increasingly recognised as a discrete and high-value activity. Geometallurgy involves a quantified and spatially constrained approach to ore characterisation in terms of relationships to critical processing performance behaviours. A key outcome is enhanced economic optimisation of mining and improved risk management tools.Industry recognition of the need for large-scale, integrated research to support this emerging area resulted in commencement of a major ongoing initiative in mid-2005. The AMIRA International P843 ‘GeMIII’ project (Geometallurgical Mapping and Mine Modelling) is a cross-discipline collaboration involving a number of world-class research organisations supported by over 20 industry sponsors.The project is delivering integrated tools and methods which link intrinsic rock characteristics to prediction of mineral processing performance. These indices must be capable of spatial distribution in 3D resource models and incorporation into mine planning and optimisation. A key aspect is provision of new cost-effective tools and methods which can provide the large numbers of measured and estimated data points required to undertake effective modelling and spatial distribution. The integrated methodology and enabling technologies being developed through the ongoing AMIRA GeMIII project are outlined, together with implications for supporting industry best practice.

Sep 5, 2011

In November 1992, the Internal Revenue Commission (IRC) was formed from the rperggr of the Papua New Guinea Taxation Of- fice (PNGTO) and the Bureau of Customs, and now has the re- sponsibility for the administration of direct and indirect taxes on a national basis in Papua New Guinea (PNG). Since that date we have undertaken many initiatives to make the new organisation more efficient and responsive to clients' needs. Income Tax The mining industry is catered for, in respect of income tax, un- der a separate taxation regime within the Income Tax Act (ITA), Division 10, as well as some general provisions within that Act as may be applicable. Division 10 is itself broken up into subdi- visions to cover the different types of mining leases, namely Spe- cial Mining Leases (SMLs) and Mining Leases (MLs), and peri- ods of time during which those sub-divisions apply. Ring Fencing Income tax assessed on the mining industry, with the exception of Mining Leases (these will be explained later), has a project basis of assessment, that is, each project is assessed separately as if the taxable income of the taxpayer from operations attributable to the project was the only assessable income derived by that taxpayer. This is often referred to as "ring fencing". This is an important point to consider because losses from unsuccessful projects cannot be set off against income from those that are suc- cessful, except in very limited specific circumstances, such as where an unsuccessful exploration licence is cancelled or surren- dered. The project basis of assessment applies to both resident and non-resident companies. A relaxation in the 'ring fence' provisions was applied from 1st January 1995, where ten percent of exploration expenditure, in- curred in areas outside of Special Mining Leases and Petroleum Development Licences in a particular year of income, can be claimed as an outright deduction which is limited to ten percent of the tax otherwise payable in that year. This was introduced to encourage exploration in PNG.

Jan 1, 1997

By S Grimsey, E Janetzki, J Emery

Floor failure on the longwall face is a complex problem due to the dynamic interaction between the surrounding strata and powered roof supports involving multiple variables. It can also be highly problematic and costly when not well understood as there are significantly less remedies available post event. This was the early experience at the case study mine where significant lost time was incurred due to unplanned delays in the first two panels. To detect and prevent such occurrences is clearly the best approach, hence a tool to predict both floor failure occurrence and magnitude prior to mining was developed. Several parameters were determined as the key drivers for the failure events that had been experienced at this site. These parameters were, in list of influence from highest to lowest, material strength, retreat rate and the presence of water. The parameters were evaluated using a semi quantitative risk rating system ‘Heave Risk’ and given a weighting per their apparent influence. This ‘expert system’ methodology was selected as the use of risk rating systems in underground coal mining is well established. The heave risk model was first applied to previously mined panels. It accurately identified all areas of known major floor heave, with clearly defined areas of low and high risk apparent. The heave risk model was then used prior to mining and evaluated post mining based on observed conditions. It was found to also be highly accurate for prediction. The variability of each parameter and its influence on the overall risk rating is illustrated and discussed.

Nov 29, 2022

By Moore A. J

Blasting in mines in an urban environment can be conducted safely and within regulatory vibration limits by careful attention to detail and the application of correct techniques. Factors affecting blast vibration are described using surface and underground mining examples. An understanding of these factors provides an essential base for effective planning and operational control. Techniques are described for assessing and predicting vibration levels and the presentation of data for planning purposes such as environmental impact statements for new projects and the protection of buffer zones around existing operations.

Jan 1, 1997

By E Topal

Risk and uncertainty are attached to mining projects, and making decisions, hedging, future investment and evaluation of mining projects depend on forecasting the future price. The future technologic developments in mining will be primarily influenced by the future commodity prices. A few approaches, with different confidences are proposed to predict price movement in the future. This research introduces a new comprehensive version of the mean reverting jump diffusion model for natural-resource commodity prices. The novel model proposes that the historical data of mineral commodities have three terms to demonstrate fluctuation of prices: mean reversion component, diffusion component and jump component. The model calculates each term individually to compute the future prices of mineral commodities. Subsequently, in the second section of the paper, the model is implemented for monthly historical data of gold price from January 1968 to May 2008. This research is investigating the relationship between the historical oil price and inflation with the gold price. This is followed by a future estimation of gold price fluctuations up to 2018. The results from the application of this new method are discussed in the context of how they accurately replicate the historical gold price and how they can predict the future gold price.

Jan 1, 2008

New Zealand Steel Limited is nearing completion of the environmental reporting and planning procedures for its proposed fivefold expansion to steelmaking at Glenbrook, and supporting mining operations at Waikato North Head. A report on the proposal to transport concentrate from the mining operations to Glenbrook has also been prepared and is awaiting release. This paper draws from these events, and by discussing some of the problems encountered, gives some guidelines for the preparation of an Environmental Impact Report.

Jan 1, 1981

Edie Creek is located in the Morobe Goldfield about 17km by road from Wau in the Morobe Province of Papua New Guinea (PNG). Four distinct periods of mining development have occurred since discovery of rich alluvials in 1926. During the two years following discovery, individual expat-riate miners with gangs of native labourers mining rich alluvial gravels dominated the field. After the discov-ery of hardrock mineralisation in 1927, companies accumulated leases and devel-oped extensive underground mines and mechanical processing plants at Day Dawn Mine and Edie Creek/Karuka Mine between 1929 and 1942. After the Second World War, the underground operations were not re-opened, and mining activ-ities mostly concentrated on working alluvial and eluvial deposits. From 1962 onwards, Papua New Guinean miners became increasing producers as company activities declined. In 1990, Edie Creek Mining Company Pty Limited, a joint venture company involving Wau landowner groups commenced operations on New Guinea Goldfield's leases. It currently mines by open pit methods, rich quartz stringers and is invest-igating the open pitting of the Edie Creek/Karuka underground workings.This paper describes the mining and processing techniques employed during the various phases of develop-ment at Edie Creek in the past 70 years. The problems and hardships of operating on a new and remote goldfield are outlined.Abstract

Jan 1, 1994

Universities have had a long history in the education of geology graduates, Analysis of this history reveals a record of success, as judged on a world basis. However there have been significant changes in the last 20 years that have impacted on the ability of universities to continue to provide their traditional style of geology education. These changes have increased in the last 10 years. In the teaching side, there has been a change in expectations. Additionally the increasing workload decreases the value of each academic to perform the tasks needed by the new education. In the area of research, the funds provided have continued to decline, in both real and absolute terms, and it is now necessary for universities to seek out funds to pay for their postgraduate research. Additionally, the universities have slipped into the error of what cahn only be termed "academic incest", and research student mobility has decreased to an undesirable level, stifling initiative and new ideas in a number of cases, The only solution is for Government monies to be "directed" - ie that the postgraduate student must leave his or her original university in order to receifve the research stipend/scholarship. On the government front, the government and its agencies have not adequately analysed and recognised the need for the redirection of education and research funds into the needy areas of science and technology, especially those that related to the minerals area.

Jan 1, 1986

Transport technology has produced social changes since the invention of the wheel five millenna ago when man was freed from the need to expend large amounts of energy to move goods and people. Further impetus came with the Industrial Revolution when mechanical power producing devices were applied to land and-water transport. This leap, together with the application to air transport has caused enormous social changes in our way of life. The state of technological advancement of transport modes has dictated to a large degree the develop- ment of Australia and Papua New Guinea. It is suggested that we should not make advances for technology's sake but examine the real needs of the users of transport and ensure that the un- necessary costs are not incurred. The transporting techniques for the ore, waste and slurries used by Bougainville Copper in Papua New Guinea are, in general, quite conven- tional but the scale of operations and the location has modified some modes. in particular the soft' overburden and concentrates were slurried for trans- port and the lack of experience in humid climates restricted the choice of the mine haulage truck. The near future of the transport. industry is seen as an expansion in equipment sizes but the suggestion is made that we need to examine more than the economic and technical aspects; it is necessary for the social con- sequences of our actions to bear examination by outside opinion

Jan 1, 1973

By J Rutter, J du Plessis, er, M Scott, D Alex

It is generally acknowledged that bulk ore sorting is an attractive prospect for the mining industry. However, uncertainties relating to the operational performance of sensor technologies, the grade heterogeneity present in analysed material and the physical separation performance of the coupled system complicate the evaluation and deployment of bulk ore sorting strategies at operations. To assist in the quantification of these uncertainties, the Cooperative Research Centre for Optimising Resource Extraction (CRC ORE) and Anglo American have implemented a systematic methodology to evaluate the deployment of sensor technologies for bulk ore sorting. This methodology was implemented at a bulk ore sorting demonstration plant using penetrative prompt gamma neutron activation analysis (PGNAA) and surface x-ray fluorescence (XRF) measurements of base metals, as a proxy for precious metals, at Mogalakwena PGE Mine. The methodology comprises of three phases. The initial phase involves the preliminary investigation of sensor technologies and analysis to reduce identified risks prior to commissioning of the bulk ore sorting plant. The second phase executes a series of experiments to prove the sensing technologies in the operational environment and provide confidence the sensors can drive separation. The final phase demonstrates the production scale bulk ore sorting performance of the plant and validates its performance by campaign of the sorted products at the processing plant. Throughout the operational deployment and evaluation of bulk ore sorting at Mogalakwena, several key lessons were learned. These learnings relate to the calibration requirements of the sensor technologies, the application of surface vs penetrative sensor techniques and the preservation of grade heterogeneity delivered to the sensors. This paper presents the methodology used, and lessons learned, in the operational deployment and evaluation of PGNAA and XRF sensors for bulk ore sorting at Mogalakwena PGE Mine.

Nov 10, 2020

By S Garnes, W Austerberry, S Fraser

Despite significant investment in safety in the mining industry (mostly focused on processes and systems), many companies are unable to sustain and further improve their performance resulting in continued workplace incidents. The problem persists despite the best efforts of companies and allocation of resources to achieve Zero Harm. A DSS survey in 2019 found that two out of five companies that cannot manage risks and face disaster, leave the market within five years. All safety/risk management systems have the common steps of risk identification, prioritisation, design of controls consistent with risk tolerance, and verification of implementation/operability of controls. This is then complimented with improvement to one or more of the above elements through learnings obtained from incident investigations. In principle, the above process should work to reduce risks to, and keeping them at, a risk level consistent with risk tolerance in the organisation.

May 5, 2022