Search Documents

By Edwin C. Barringer

IRON and steel scrap has again become page one news, as it was during the war. To many this is anomalous because the common concept is that the theaters of war are literally paved with scrap as the by-product of war damage and abandoned materiel. To an extent this is true, the bottleneck being the ferreting out and transportation of this scrap. While you as consumers of the electric-furnace grades of scrap-the premium grades-are concerned primarily in only one segment of the scrap market, I believe you ill be interested in a general discussion of the market with subsequent funneling down to your specialty.

Jan 1, 1947

By Pradeep K. Rohatgi, Clyde M. Adams

Dendritic aggregate of ice formed on freezing of aqueous soluitions has been studied. Chlorides of sodium, potassiutn, lithiunz , and hydroget1 were used as solutes. The spacing between ice platelets or den-drites was experimenlally found proportzonal to the square root of freezing time when the freezing rate was constant from beginrting to end of solidification; the constant freezing rates were obtained during freezing of small droplets of aqueous soliitions surrounded by relatively large heat sinks. The transverse growth velocity of the ice platelets is proportional to the square root of the freezing rate. During unidirectional freezing from a constant temperuture chill, the solution at each location is subjected to a spectrum of freezirtg rates. The freezing rate is ini- FREEZING of solutions has been a subject of investigation in many disciplines. Aqueous solutions offer the advantage of transparenty; their study is of special significance due to the increasing interest in freezing processes for desalination. In addition dendritic solidification of aqueous solutions is in many ways analogous to freezing of metallic solutions. Aqueous solutions of most ionic salts freeze with tially low, passes through a maximum, and then decreases until solidificatimz is complete. The den-drite spacing increases linearly with the distance from the chill surface; it is inversely profiortional to the square root of the maximum freezing rate. The dendrite spacings in the two systems (the constanl freezing rate and the varying freezing rate) are equal, when the maximum freezing rate of the varying freezing rate system equals the average freezing vale of the constant freezing rate system. Mass transport in interdendritic liquid duriug solidificatiotz is analyzed; the experimental observations indicate that maximum concentration difference (AC) and supercooling (AT) in the interdendritic liquid are indepexdent of freezing rate. the separation of practically pure ice crystals from the liquid phase; with very few exceptions there is no solid solubility of ionic salts in ice. As an ice crystal grows there is rejection of solute from the moving interface into the liquid. Since the rejected solute moves primarily by diffusion, concentration gradients are established in the liquid. The highest solute concentrations are found in liquid immediately adjacent to liquid-solid interfaces and lowest concentrations farthest from the interface. Two-phase equilibrium obtains only at the solid-liquid interface; at other locations the liquid becomes supercooled because temperature gradients are negligible compared to concentration gradients. This is an immediate consequence of the fact that thermal diffusivities are considerably higher than mass diffusivities.

Jan 1, 1968

By Paul T. Allsman

1.1-1. Current Status. The history of surface mining is essentially that of mining coal, copper, and iron ores, and the nonmetallic minerals--clays, gypsum, phosphate rock, sand, gravel, and stone. Table 1.1-1 is a comparison of the estimated world production of crude metallic and nonmetallic ores and coal with that of the United States for 1964, in short tons. It includes an estimate of the quantity produced by surface mining methods. Two-thirds of the 8.8 billion tons are mined from surface, ranging from a third of the coal, half the metallic ores, and nearly all clays, stone, sand, and gravel. In the United States, production by surface methods parallels that of the world with two major exceptions: 74% of copper ore and 90% of usable iron ore are mined from the surface, whereas outside the country less than 40% of copper ore and only 50% of usable iron ore are mined from the surface. In surface mining of both metallic ores and coal, much waste is stripped, but in mining nonmetallics the ratio between waste and ore is small. Assuming that the stripping ratio for surface mining in the United States will apply equally to world production, it is estimated on a weighted basis that over 21 billion tons of waste, or a total of nearly 27 billion short tons of material, are mined annually in the world by surface methods. Data are not available to confirm the assumption for waste stripping outside the U.S., but the estimate expresses an order of magnitude that is worth noting. Table 1.1-2 shows the materials-crude ore, coal, and waste-mined by surface methods and the relation to total mined by both surface and under- ground methods in the United States during 1964. Eighty-two percent of all crude metallic and nonmetallic ores and coal was mined from the sur- face, including 82% of metallic, 96% of nonmetallic ores, and 35% of coal. Copper and iron ore comprise 83% of the metallic ores mined from the surface, and clays, gypsum, phosphate rock, sand, gravel, and stone

Jan 1, 1968

By M. E. Wadsworth, I. B. Cutler, R. W. Bartlett

The oxidation kinetics of ZrC was studied between 450" and 580°C in oxygen pressures from 6.5 x 10-to 1 atm using a ther mogravimetric apparatus and sized powder samples. Two parallel rate controlling processes were observed. A surface reaction occurring at the ZrC-ZrO2 phase boundary accounted for most of the oxidation and had an activation enthalpy of 46 kcal per mole. The other process, believed to be diffusion of oxygen into the ZrC lattice partially replacing carbon, had an activation enthalpy of 53 kcal per mole. The enthalpy for chemisorption of O2 on ZrC was determined to be —13 kcal per mole. Water vapor in the presence of oxygen accelerated the surface reaction rate. THERE has been little reporting of formal rate studies or attempts to ascertain the mechanism of oxidation of carbides. MacDonald and Ransley1 studied the oxidation of titanium carbide which has the same structure as zirconium carbide, fcc. They observed an initial increase in rate with increasing temperature followed by a rapid decrease through a rate minimum and a subsequent second increase at higher temperatures. The discontinuity in the rate rise was attributed to a phase change in the oxide which changed the rate determining step from the surface reaction at the carbide-oxide interface to diffusion through the oxide layer. Samsonov and Golybera 2 studied titanium carbide and reported that during the initial period of oxidation a dense film of Tic-TiO was formed followed by the formation of less adhering layers of higher oxides. The purpose of this investigation was to study the kinetics of oxidation of zirconium carbide and to attempt to gain some knowledge of the mechanism by which oxidation occurs. EXPERIMENTAL PROCEDURE Measurement of the weight gain associated with the oxidation of ZrC was used to determine oxidation rates. The principal experimental parameters were surface area, temperature, and oxygen pressure. Although moderately sized crystals of ZrC can be grown by the Van Arkel method, the only commercially available ZrC is a powder. In using powders, the surface area must be controlled either by fabricating the powder into a sintered pellet with a measurable surface area, relatively fixed during oxidation, or by using sized unconsolidated powder and applying appropriate geometric considerations to the shape of the grains to correct for their diminishing surface areas as they oxidize. Both techniques involve some difficulties. pellets of binder-free zirconium carbide can be made by hot pressing, but it is difficult to obtain densities greater than 90 pct of

Jan 1, 1963

PRESIDENT. CHARLES F. RAND,1 NEW YORK, N. Y. PAST PRESIDENTS. CHARLES KIRCHHOFF,1 NEW YORK, N. Y. JAMES F. KEMP,2 NEW YORK, N. Y. FIRST VICE-PRESIDENT. BENJAMIN B. THAY ER,1 NEW YORK, N. Y. TREASURER. GEORGE C. STONE,1 NEW YORK, N. Y.

Jan 4, 1913

By Robert L. Hoss

The application of Muskat's differential equations for predicting the performance of a solution gas-drive reservoir to the Fullerton field indicates that a recovery may be expected of 14,030 bbl per acre under primary depletion, and 15,910 and I7,190 bbl per acre, respectively, under the two pressure-maintenance programs analyzed. In this analysis it is assumed that fluid properties are the same throughout the reservoir, that the core data used are typical of the Clear Fork limestone in the locality, and that injected gas is completely diffused through the pay zones. The economic study of the three recovery programs considered indicates that the one in which 60 pct of the produced gas is returned to the formation is the most profitable. Introduction The purpose of this paper is to consider the effect of pressure maintenance by gas injection on the ultimate recovery of oil from a solution gas-drive reservoir. This prediction of reservoir behavior is the result of calculations based on the equations presented by M. Muskat in the Journal of Applied Physics, March 1945. Reservoir The reservoir analyzed is the Fullerton field in Andrews County, West Texas. It is situated on a broad anticlinal structure with approximately 330 ft of closure, and extends approximately eight miles north and south and five miles east and west. The areal extent is taken as 16,642 acres. The producing horizon is the Lower Clear Fork limestone of Permian age, occurring at depths from 6650 to 7350 ft. It is divided into four zones. For the purposes of this study, the fluid characteristics in all zones are assumed to be the same. Therefore an equivalent zone is assumed of thickness equal to the sum of the thicknesses of the four zones, or an average of 216 ft. The reservoir contains 3,586,991 acre feet of producing limestone, with an initial volume of stock tank oil in place of 918,-403,100 bbl. The average connate water saturation is 24.0 pct. The permeability ranges from 6.7 md. to 12.6 md., and the porosity ranges from 7.7 pct to 11.4 pct, except for occasional cavernous streaks. Based on these values, the limestone may be considered intergranu1ar.l Production histories and material-balance studies have indicated that the driving mechanism is solution gas. Water levels have been established. Theory It is possible to express mathematically the change in residual oil saturation with pressure decline in a solution gas-drive reservoir as being equal to the change in the physical properties of the fluids present in the reservoir as this pressure decline occurs. Essentially these equations, in differential form as presented by M. Muskat,2 express quantitatively the instantaneous net effect

Jan 1, 1948

By Robert L. Hoss

The application of Muskat's differential equations for predicting the performance of a solution gas-drive reservoir to the Fullerton field indicates that a recovery may be expected of 14,030 bbl per acre under primary depletion, and 15,910 and I7,190 bbl per acre, respectively, under the two pressure-maintenance programs analyzed. In this analysis it is assumed that fluid properties are the same throughout the reservoir, that the core data used are typical of the Clear Fork limestone in the locality, and that injected gas is completely diffused through the pay zones. The economic study of the three recovery programs considered indicates that the one in which 60 pct of the produced gas is returned to the formation is the most profitable. Introduction The purpose of this paper is to consider the effect of pressure maintenance by gas injection on the ultimate recovery of oil from a solution gas-drive reservoir. This prediction of reservoir behavior is the result of calculations based on the equations presented by M. Muskat in the Journal of Applied Physics, March 1945. Reservoir The reservoir analyzed is the Fullerton field in Andrews County, West Texas. It is situated on a broad anticlinal structure with approximately 330 ft of closure, and extends approximately eight miles north and south and five miles east and west. The areal extent is taken as 16,642 acres. The producing horizon is the Lower Clear Fork limestone of Permian age, occurring at depths from 6650 to 7350 ft. It is divided into four zones. For the purposes of this study, the fluid characteristics in all zones are assumed to be the same. Therefore an equivalent zone is assumed of thickness equal to the sum of the thicknesses of the four zones, or an average of 216 ft. The reservoir contains 3,586,991 acre feet of producing limestone, with an initial volume of stock tank oil in place of 918,-403,100 bbl. The average connate water saturation is 24.0 pct. The permeability ranges from 6.7 md. to 12.6 md., and the porosity ranges from 7.7 pct to 11.4 pct, except for occasional cavernous streaks. Based on these values, the limestone may be considered intergranu1ar.l Production histories and material-balance studies have indicated that the driving mechanism is solution gas. Water levels have been established. Theory It is possible to express mathematically the change in residual oil saturation with pressure decline in a solution gas-drive reservoir as being equal to the change in the physical properties of the fluids present in the reservoir as this pressure decline occurs. Essentially these equations, in differential form as presented by M. Muskat,2 express quantitatively the instantaneous net effect

Jan 1, 1948

By Robert T. Walker

Robert T. Walker and Woodville J. Walker (Walker Engineering Corp., Salt Lake City)-Mr. Kinkel's article embodies, in condensed form, the results of the first detailed and complete geological survey that has ever been made of the long neglected but potentially very important West Shasta Copper-Zinc district, in Shasta County, California. In view of the difficulties of the terrain and the complexity of the geological structure, this represents a notable achievement, and it is with regret, therefore, that the writers find it necessary to differ from Mr. Kinkel's conclusions on two important points. The first has to do with the interpretation of two members of the stratigraphic column of formations in the district; for purposes of comparison, the description of these two members according to Mr. Kinkel is shown parallel to the description of these members according to the writers, see Fig. 14, Mr. Kinkel's nomenclature being used

Mar 1, 1956

By AIME AIME

FOR constructive research in copper and brass and other non-ferrous metals and their alloys, and his contributions to the establishment of the present accepted high standards of quality William H. Bassett, technical superintendent and metallurgist of the American Brass Co., has been awarded the James Douglas Gold Medal for 1925. Mr. Bassett was born in New Bedford, Mass., on March 7, 1868, and was graduated in chemistry at the - Massachusetts Institute of Technology in 1891. In the same year he went to Pope's Island Manufacturing Co., at New Bedford, as chemist where he remained until 1895, where he became a teacher in chemistry at the Swain Free School, which position he retained until 1900. He then became chemist for the New Jersey Zinc Co., at Newark N. J., and in 1902 went to the Coe Brass branch at Torrington, Conn., as Chemist. In 1903 he became chief chemist and metallurgist and since 1912 has been technical superintendent and metallurgist of the American Brass Co., with head- quarters at Waterbury, Conn.

Jan 1, 1924

By B. L. Thane

Within the past few years, the mining industry has taken a new impetus in all its branches. New mines are being opened every day, while old ones, which have been either working at a loss, or have been compelled to shut down, are now gradually being reopened and placed on a paying basis. This growth and new life is due, in a measure, to the discovery of new mining districts, but the most important cause of the progress is the wonderful advance that has been made in all branches of mine-engineering. By means of the important inventions and discoveries that have been made in mechanics, chemistry, and electricity, we are now able to work ores which, only a short time ago, would have been regarded as worthless. We find, for instance, the electrician eliminating two of our greatest difficulties, those of distance and superior elevation, while the mechanic has brought to the highest degree of perfection, not only ore-crushing and hoisting machinery, but all such devices as pertain to the mechanical handling of ores, and, at the same time, the metallurgist, with his combined chemical and mechanical skill, has helped us to extract the precious metals from the most refractory of ores. But when we turn to examine methods in actual use for

Jan 1, 1900

A SERIES of papers on strategic and otherwise important mineral products was prepared some ten years ago under the joint auspices of the Committee on Foreign and Domestic Mining Policy of the Mining and Metallurgical Society of America and the Committee on Industrial Preparedness of the American Institute of Mining and Metallurgical. Engineers. These papers were later published in a joint volume entitled International Control of Minerals (1925). Amongst them was one on manganese. The Subcommittee on Manganese prepared its paper in two forms. One was intended for inclusion with the series above referred to and approached its subject more particularly as an international problem. The other dealt more definitely with manganese as an element in the problem of national defense. This last was first written under date of January 24, 1924 as a confidential report, for and at the request of the War Department. It was later released and published, in slightly modified form, as a separate pamphlet by the Industrial Preparedness Committee of the American Institute of Mining and Metallurgical Engineers. After the lapse of eight years, in view of the vital position of manga-nese in the problem of industrial preparedness against a war emergency, the War Department made a request to have the conclusions of 1924 reviewed and brought up to date. To comply with this request the manganese subcommittee was reconvened (with a somewhat changed personnel) and exhaustive studies were once more made of the entire subject of manganese. A new report, with specific recommendations, was submitted to the War Department in February, 1932. This second report is now herewith released for publication. Certain specific conclusions and recommendations as expressed to the War Department are omitted. Otherwise the report stands as prepared and submitted by the manganese subcommittee of 1931. The members of this committee were: C. Minot Weld, Chairman, R. C. Allen, Arthur S. Dwight, J. W. Furness, D. F. Hewett, Reno H. Sales, Theodore Swann and Scott Turner. ARTHUR S. DWIGHT, Chairman, Committee on Industrial Preparedness.

Jan 1, 1933

FOREWORD A SERIES of papers on strategic and otherwise important mineral products was prepared some ten years ago under the joint auspices of the Committee on Foreign and Domestic Mining Policy of the Mining and Metallurgical Society of America and the Committee on Industrial Preparedness of the American Institute of Mining and Metallurgical Engineers. These papers were later published in a joint volume entitled International Control of Minerals (1925). Amongst them was one on manganese. The Subcommittee on Manganese prepared its paper in two forms. One was intended for inclusion with the series above referred to and approached its subject more particularly as an international problem. The other dealt more definitely with manganese as an element in the problem of national defense. This last was first written under date of January 24, 1924 as a confidential report, for and at the request of the War Department. It was later released and published, in slightly modified form, as a separate pamphlet by the Industrial Preparedness Committee of the American Institute of Mining and Metallurgical Engineers. After the lapse of eight years, in view of the vital position of manga-nese in the problem of industrial preparedness against a war emergency, the War Department made a request to have the conclusions of 1924 reviewed and brought up to date. To comply with this request the manganese subcommittee was reconvened (with a somewhat changed personnel) and exhaustive studies were once more made of the entire subject of manganese. A new report, with specific recommendations, was submitted to the War Department in February, 1932. This second report is now herewith released for publication. Certain specific conclusions and recommendations as expressed to the War Department are omitted. Otherwise the report stands as prepared and submitted by the manganese subcommittee of 1931. The members of this committee were: C. Minot Weld, Chairman, R. C. Allen, Arthur S. Dwight, J. W. Furness, D. F. Hewett, Reno H. Sales, Theodore Swann and Scott Turner. ARTHUR S. DWIGHT, Chairman, Committee on Industrial Preparedness.

Jan 1, 1933

By Amos P. Brown

PYRITE, the bisulphide of iron, FeS2, is found more or less in all coal-beds: but, as a rule, in certain definite forms. More than any other impurity, it detracts from the commercial value of a coal-deposit, and yet its presence is so universal that it might almost be said that there is no coal entirely free from pyrite. My observation has been confined to the Pennsylvania bituminous and semi-bituminous coals, and to them, therefore, my remarks will be confined. Certain generalizations which I may make, however, will be found of universsl application. The lowest members of the coal-formation, No. XIII. of the Pennsylvania bituminous region, are nearly always pyritiferous, and in many cases highly so. In Cambria county, for instance, coalbed A, the Brookville, is locally known as the " Sulphur seam." The Lower Kittanning, in parts of Clearfield county, is so sulphury as to be almost unmarketable, though otherwise it is a strong locomohive coal. In Mercer county the Pardoe bed, so extensively mined there, carries great quantities of sulphur in the form of pyrite, though usually this can be separated in such a way as to detract little from the market-value of the coal. The other coal-beds of the Lower

Jan 1, 1888

By F. E. Pawlek, J. K. Gerlach

The chloridizing roasting of ores is applied when metal sulfides and oxides are to be converted into soluble or volatile compounds. The chlorine required is either obtained from the admixed chlorides of sodium or calcium or added in the gaseous state. In the first part of the investigations the reaction rate of the chlorides of sodium or calcium with gas mixtures of SO,-0, or SO ,-O2 ,-SO , was measured. The rate for reactions with gas mixtures SO2-O2 is ThE chloridizing roasting of ores is applied when metal sulfides and oxides are to be converted into soluble or volatile compounds. At present the process is mainly applied to produce nonferrous metals which occur in pyrite cinders in small concentrations. Thereby the nonferrous metals are converted into water-soluble, acid-soluble, or volatile compounds whereas all the iron remains as insoluble oxide. The chlorine required is either obtained from the admixed chlorides of sodium or calcium or added in the gaseous state. The reactions occurring during the roasting process can be divided into two groups: solid-solid reaction and gas-solid reaction. The reactions between solids proceed by means of solid-state diffusion and are therefore of low velocity. The heterogeneous reactions between solids and gases of the roasting atmosphere5 are high-velocity processes and determine the velocity of the chloridizing roasting. These gas-solid reactions shall be the subject of the paper presented. In order to investigate the still little-known processes which occur during the chloridizing roasting 6-' the complex reaction is split into several partial steps. First the reactions of NaCl and CaCl, with gas mixtures of SO2 and 0, have been investigated at temperatures between 500" and 600°C by measuring the weight increase of the samples. The gas mixtures used in this series of experiments had first variable compositions, then the amount of SO 2 had been increased. Furthermore the influence of Fe 2 O3 admixtures upon these reactions, the behavior of pure Fe 2 O3 with the gaseous reactants, and the chlorination of the sulfides of lead, copper, nickel, and zinc have been investigated. FORMATION OF GASEOUS CHLORINE Pyrite cinders are never completely roasted and therefore contain still a small amount of sulfide sulfur. When heated again in air, this sulfur is converted into SO,. Accordingly the formation of chlorine can first be described by the reactions: dependent on the composition of the gas phase. If more than 1 pct SO 3 is added to the roasting gas, the reaction rate is determined only by the concentrations of the SO,. In the second part the reactions between chlorine and metal sulfides are discussed. The rate of formation of gaseous chlorine is higher by me order of magnitude than is the reaction rate between ZnS and chlorine. The reaction rate of NiS and PbS lies considerably below that of ZnS. The conversion rate of both pure Fe 2 O 3 and Fe 2 O 3 containing NaCl or CaCl2 when reacting with SO2-O2, mixtures with and without SO3 portions was measured at temperatures of 500", 550°, and 600°C. The weight increase of pressings was determined by means of a spiral balanceg and the reaction rate calculated therefrom according to Eqs. [ll to [31 and [5] to [7]. The prepared samples were suspended on a platinum filament in a vertically mounted tube of mullite (ID 4 cm, length 110 cm) which could be heated by a resistance tube furnace. The platinum filament was tied to the lower end of the spiral balance. A supremax glass tube (length 70 cm) was mounted gas-tight on top of the reaction tube. The unit was sealed up at its top by a ground-in stopper which was holding the spiral balance with the sample. The spiral balance therefore hung outside the high-temperature region of the furnace. Fig. 2 shows the experimental arrangement schematically. While lowering the sample into the reaction tube pure nitrogen was flowing through the reaction zone providing a protective atmosphere. After the sample had reached the reaction temperature within approximately 1 min, the protective gas was replaced by the sulfur dioxide-oxygen reaction mixture. It took about 30 sec until the mixture filled the tube homogeneously. A Ni/NiCr thermocouple placed in the center of the furnace where the sample hung during the measure-

Jan 1, 1968

By W. J. Sharwood

(San Francisco Meeting, September. 1915) THE assay or estimation of the total gold content of an ore presents little difficulty, when circumstances permit of securing a thoroughly representative sample. The general practice has been fairly standardized, and such errors as occur in the results obtained are for the most part attributable to the methods of sampling rather than to those of assaying, while duplicate assays made by skilled workers usually agree closely. When it is a question of estimating the "free" or amalgamable gold of an ore, as opposed to the total gold, there is but little uniformity in the methods employed by different workers, and often equally little in the results obtained when duplicate determinations are attempted, no satisfactory standard method having been generally adopted. The methods in use are of two general types-"panning" and "amalgamation."

Jan 8, 1915

By Henry P. Ehrlinger, James C. Bradbury

Tripoli is a naturally occurring, very finely divided form of silica found chiefly in some midwestern and southeastern states and used commercially as fillers and abrasives. Definitions Tripoli is a microcrystalline, finely particulate, more or less friable form of silica that appears to be the product of leaching of siliceous limestone or calcareous chert. The term was originally applied to a deposit near Seneca, Mo., that resembled material of that name found near Tripoli in North Africa (Hovey, 1894). The two deposits were subsequently found to have different physical characteristics -the North African tripoli, now called tripolite, is a diatomite, composed of the siliceous skeletons of microscopic marine plants called diatoms, and the Missouri tripoli contains no diatom remains; the term tripoli, however, continued to be used for the Missouri material and is now applied in a general way to most silica deposits similar to it in characteristics and geologic origin. In commercial trade tripoli is commonly understood to designate material from the Missouri-Oklahoma field; silica from southern Illinois, the other major producing area, is referred to commercially as amorphous silica. Each term, however, may be used commercially for material, regardless of place of origin, that has the characteristics or uses commonly ascribed to the material from one or the other major producing area. For example, in the commodity price listings, Engineering and Mining Journal routinely lists under Tripoli, prices "f.0.b. Elco, III." and "f.0.b. Seneca, Mo., and Rogers, Ark.," and under Silica, amorphous, prices "f .o.b. Ill.," and "f .o.b. Dierks, Ark." Amorphous silica, the commercial designation given to southern Illinois tripoli, is, like the term tripoli, a misnomer. Mineralogically, the southern Illinois deposits are composed of microcrystalline quartz, and no amorphous material has been detected during X-ray and scanning electron microscope investigations (Leamnson, Thomas, and Ehrlinger, 1969; Thomas et al., 1970). Soft silica is another term that has been applied to Illinois and Tennessee tripoli, presumably to distinguish it from the more compact Missouri material. It has also been used in the ceramic trade to distinguish tripoli from "hard" silica, or silica flour, produced by pulverizing silica sand (Heinz, 1937). Rottenstone, produced commercially in Pennsylvania, is similar to tripoli in that a major constituent is finely particulate silica, and its uses are much the same as those of tripoli- as abrasives and fillers. The origin of rottenstone also is similar to that of tripoli-decomposition of a siliceous sedimentary rock. The parent rock is defined as a siliceous limestone (Gary, McAfee, and Wolf, 1972; Thrush, 1968) or as shale (personal communication). Heinz (1937) quotes a brief statement describ-

Jan 1, 1975

By J. C. M. Li

This exploratory survey was undertaken to repeat some experiments- in which anomalous results were reported1 for bismuth and to measure the thermoelectric power of some bismuth alloys and inter-metallic compounds. sato1 reported that the thermoelectric power of bismuth depends on the temperature gradient. This seems rather unreasonable especially when the Benedicks effect' has not been detected. Even if the material is not homogeneous, the observed thermoelectric power can be represented by

Jan 1, 1959

By Frank Riddle

THE life of thermocouples is governed, to a large extent, by the protection they receive when in use; particularly when the temperatures being measured are high and the products of combustion are reducing in character. Several types of protection tubes are being used for this work; they are made of ordinary and aluminous porcelain, fused quartz, carborundum, fused alumina, fireclay, and some kinds of metal. All of them may render good service under certain conditions but they must be used for the purpose for which they are intended. For example, fused-quartz tubes are very good when excessive changes in temperature occur, but under certain conditions they will crystallize and lose their strength. Porcelain is used in several ways in connection with the use of thermocouples: for insulating the two wires of the couple and to. prevent short circuits; for protecting the entire couple in a refractory gas-tight tube, which is ordinarily fastened to and is considered part of a properly equipped thermocouple; and for protecting the complete thermocouple from the possibility of physical injury and to support it. This tube is made porous and strong and is ordinarily built right into the wall or crown of the furnace, as the case may be. The insulating tubes must be small and sufficiently refractory to withstand the temperatures at which they are to be used. The length of the tubes, porosity of the material from which they are made, etc. does not particularly matter. The tubes are sometimes made with two or even four holes, the latter being used where it is desirable to have two couples as close together as possible for calibration work. The thermocouple protection tube must be of proper size to permit the thermoelements and insulating tubes to be inserted or taken out easily. It must be porous enough to withstand sudden changes in temperature and yet gas-tight, as well as refractory enough to withstand the furnace temperature, even if the tube protrudes into the furnace in a horizontal position without support for a reasonable distance. If the

Jan 9, 1919

By R. S. Busk, E. G. Bobalek

THE relation between gases and metals has been a subject of increasingly active investigation during the past years, principally devoted to the study of metal-hydrogen systems. It has been found that hydrogen is soluble in most molten metals to an appreciable extent and somewhat soluble in most solid metals.1,2 In every known case there is a sudden decrease in solubility at the melting point. Thus a freezing mass of metal containing hydrogen in excess of the solid solubility must in some way expel that excess during the freezing process. This leads to internal blowholes, and such effects as pinhole porosity. Gas trapped in metal that is to be fabricated by a working process such as extrusion or rolling may be the cause of blisters. For some cases, notably in copper and iron alloys, the presence of hydrogen can lead to extreme embrittlement of the metal. The aluminum-casting industry has long recognized the importance of hydrogen in its techniques. Excess gas in molten aluminum alloys often leads to the formation of "pinhole porosity" in the solid casting.3 To prevent this hydrogen pickup it is necessary to avoid overheating the melt and to protect it from such sources of hydrogen as water. In spite of all precautions, it is sometimes necessary to extract hydrogen from the melt just before pouring by bubbling with a gas such as chlorine or nitrogen. Recently it has been found that somewhat similar effects are possible with magnesium alloys, in that the presence of hydrogen can induce or aggravate microporosity.4-6 This paper is primarily concerned with a presentation of some facts concerning the solubility of hydrogen in magnesium and its alloys, with some discussion of the significance of these facts in a practical sense. In any study of gas-metal systems it is important to bear in mind a clear distinction between adsorption on surfaces and absorption within the lattice.1 Considerable attention has been directed toward determining whether hydrogen is truly soluble in any solid metal, or whether the gas extracted from a sample was present at surfaces (external and internal) only.7 Most present day evidence supports the idea of true solution in addition to adsorption. A second important factor when dealing with gas solubility is the dependence of such solubility on external pressure. For diatomic gases such as H2, solubility in both liquid and solid metals apparently is proportional to the square root of the pressure, indicating a breakdown to a monatomic gas before diffusion into the lattice .2 For true equilibrium values of solubility, therefore, the pressure at the metal surface must be constant and, preferably, known. Very little has been published concerning the hydrogen-magnesium system. Winterhager has presented the most

Jan 1, 1946

THE 143d* meeting of the American Institute of Mining and Metallurgical Engineers was held in New York, Feb. 19-22, 1934. It consisted of the annual business meeting, 45 technical sessions at which 217 papers were presented (more than ever before), two sessions of the Board of Directors, two meetings of Section delegates, three formal lectures, luncheon Monday, Tuesday and Wednesday for members and guests, three group dinners and five group luncheons, eight committee meetings, the annual reception and dinner dance, an informal dance, a smoke-dinner and the annual meeting of the Woman's Auxiliary. Attendance showed an improvement over the previous year, as follows: Total, 1534 in 1934, and 1475 in 1933; dinner dance, 543 and 426; smoker-dinner, 425 and 394; informal dance, 295 and 250; women's registration, 160 and 133; luncheons, 1034 and 734. The Coal Division held a general session and three sessions on Coal classification. It also met jointly with the Committee on Ground Movement and Subsidence. At the general session, John B. Dilworth presented a report of the Committtee on Methods of Valuing Coal Proper- ties and R. H. Sweetser a report of the Committee on Evaluation of Coal for Blast-furnace Coke. C. B Huntress, Executive Secretary of the National Coal Association, was the principal speaker at a luncheon on Monday, at which Eli T. Conner, Chairman of the Division, presided H. N. Eavenson, newly elected President of the Institute, and Edward W Parker, Secretary-Treasurer, of the Anthracite Institute, also spoke. The Executive Committee of the Division met Tuesday afternoon. The Sectional Committee on Classification of Coal met on Thursday morning and the Technical Committees on Scientific and Use Classification of Coal on Thursday afternoon. The Committee on Mining Methods held two general sessions, one for presentation of a half-dozen interesting papers on strictly mining subjects, the other on Aerial Transportation. It also participated jointly in a session on ground movement and subsidence with the committee of that name and the Coal Division The Institute's Standing Committee on Aviation had its inception at the session on Aerial Transportation

Jan 1, 1935