Search Documents

By Stanislaw Prusek

In this paper, results of underground measurements conducted in gateroad 3, seam 615, at the Bobrek-Centrum Colliery are presented. The Bobrek-Centrum Colliery is owned by Kompania Weglowa, the largest hard coal producer in the European Union. Yearly production at the colliery, including the longwall system, is about 2 million tonnes. Gateroad 3 was used simultaneously for two retreating longwall faces, No. 1 and No. 2. This working was also employed for the conveyor belt for longwall No. 1 and served as a transport road for longwall No. 2. Approximately 100 meters of gateroad 3 was maintained behind the face of longwall No.1 and then, with the progress of longwall No. 2, it was liquidated. In this paper, we present the results of underground measurements of vertical and horizontal convergence in gateroad 3. We also present the results of numerical modeling for deformation of the working. Finally, we analyse the accuracy of the numerical calculations by comparing them to the actual deformation of gateroad 3.

Jan 1, 2014

By Stephen C. Tadolini, Peter A. Gray, Robert Hawker, Andrew Sykes

"Self-drilling rock bolts (SDRBs) that use pumpable cement grout to anchor bolts have been used successfully in the tunnelling and civil engineering industries for many years. Pumpable cement grout offers a considerable advantage in that the SDRB can be fully encapsulated right down to the bearing plate, including filling cracks and cavities in the borehole. However, cement grout cannot provide the immediate rock support required for the coal industry. This paper describes a new SDRB system that uses pumpable resin to anchor the SDRB in a borehole, which not only provides all the advantages of a pumpable grout anchoring system, but also provides immediate roof and rib support as required in the coal industry. This paper further outlines the latest developments in SDRB technology including (1) extendable self-drilling rock bolts, which can almost double in length during the installation process and are particularly suited to low seam heights and rib support and (2) pre-tensioned SDRBs, where a pre-tensioned load can be applied during the installation process. These new SDRB systems offer both considerable advantages in rock support and improvements in mining productivity.INTRODUCTIONThe mining industry is continually striving to develop more efficient methods to support the roof and walls of roadways and tunnels, and rock bolting has proven to be one of the most significant improvements in ground support over the last 50 years. Rock bolting is now almost universally used in the underground mining industry worldwide, and there are many different rock bolts available.Rock bolts are traditionally made from steel or fiberglass and are anchored into a borehole with a friction-anchoring device, such as an expansion shell mechanism; cement grout; or chemical resin. Friction-anchored bolts are widely used in the Australian metal mining industry, predominantly as short-term support. They are used in conjunction with resin-anchored bolts where there is a requirement for longer life. Resin-anchored bolts are used in the coal mining industry.Friction-anchored bolts provide immediate rock support, but their load transfer capacity is poor compared to resin or cement anchored bolts. In addition, friction-anchored bolts are more susceptible to corrosion than resin or cement anchored bolts."

Jan 1, 2010

By Ismet Canbulat, John Naylor, Jason Emery, Peter Craig, Andy Sykes

"Longwall mining is by far the most common method of underground coal extraction in Australia. The industry trends and expectations are placing increasing emphasis on the reliability and productivity of these operations. The longwalls are becoming wider and longer while retreat rates are continuously increasing due to significant improvements achieved in longwall equipment reliability and automation. This increased longwall productivity is placing significant emphasis on the reliability of longwall panel development.Although there have been significant improvements in the reliability of continuous miners and hydraulic drill rigs, the traditional resin encapsulated bolt installation is still the principal method used in all major coal-producing countries around the world. Anglo American realised an opportunity existed to introduce an alternative roof bolt installation technique called “spin to stall” in Australia. Spin to stall was first introduced in Anglo American Coal in South Africa where it has been successfully used for over a decade, though implementation of South African spin to stall resin in Australia has proven to be near impossible due to a significant difference in geotechnical conditions, mining method, and, subsequently, roof bolting equipment. Therefore, a new spin to stall development project was initiated between Anglo American Coal and Jennmar Australia (SPIN2STALL®). This paper summarises the journey of this project, the results, and the successful implementation of spin to stall achieved at Grasstree Mine.INTRODUCTIONThe Anglo American Coal business unit operates Grasstree and Moranbah North underground longwall mines in the Bowen Basin of Central Queensland, with a third longwall mine, Grosvenor, currently being developed, and two more (Aquila and Moranbah South) in the project pipeline. The vision for Anglo American is to achieve “Zero Harm” through the effective management of safety at all operations, while for the coal business unit, at the same time to achieve industry-leading operational performance. Currently, both Grasstree and Moranbah North longwalls are operating at industry best practice rates. This is placing increased pressure on the development process to allow such high productivity levels to be sustainable."

Jan 1, 2015

By Ross W. Seedsman

The logical framework recognises that a coal mine roof can be intrinsically stable or may collapse in one of four ways. Suspension of the immediate roof is one of fundamental ground control strategies available to a coal mine engineer and is recommended for three of the four collapse modes. Correctly implemented suspension offers the greatest improvement in roof stability and greatest reduction in longwall risk. For the control of maingates ahead of retreating longwall faces the ideal suspension support (if required) consists of angled, partially debonded, medium-length tendons installed as far behind the development face as practical. For situations where the roof may be subjected to tensile horizontal stress, immediate support by equally spaced short vertical tendons is required. The step away from fully-grouted tendons improves their survivability during the onset of compressive failure in the roof, minimises the risk of isolated loading, and allows a more robust TARP for roof movement. All suspension systems require a strap, sling or truss between the suspension elements.

Jan 1, 2014

By Denise Mueller, Axel Preusse

"In 2010, the fracking discussion in Germany caused a number of changes in German law, which came into force in 2016. Especially the production of gas had to be regulated. With the legislation amendment, the “Subsidence-Area Mining Regulation” (in German: Einwirkungsbereichs-Bergverordnung) has been revised, too. The changes expand the compensation of mining damages, especially to the extraction with drilling from the surface and underground storage. Although the “Subsidence-Area Mining Regulation” has been revised, the area of main influence (subsidence of 10 cm) remains to determine a relevant boundary for mining damages. The determination and prediction of this boundary above caverns are presented in this paper. In addition, further elements of ground movements and their relevance to mine damages are analyzed. The usage of the area of main influence to fix a relevant boundary for mining damages does not correspond to the relevant elements of ground movements. A limit for differences in subsidence (tilt) or horizontal changes in length should be preferred to describe the relevance of mining damages on buildings. Furthermore, this paper outlines the the meaning of using the area of main influence to fix a relevant boundary for mining damages. INTRODUCTION The “Federal Mining Act” (in German: Bundesberggesetz, short: BBergG) forms the central legal standard to cover subsidence in Germany. The mining authority refers to the following regulations (Preuße et al., 2015): the “Subsidence-Area Mining Regulation” (in German: Einwirkungsbergverordnung, short: EinwirkungsBergV; since 1982) the “Mine-Surveyor Mining Regulation” (in German: Markscheider-Bergverordnung; short: MarkschBergV) the “Deep-Drilling Regulation”"

Jan 1, 2017

By Bob J. MacDonald

The Cape Breton Development Corporation is a federally owned Crown corporation in Canada that operates two coal mines the Prince and Phalen Colliery in the Province of Nova Scotia. Retreat longwall mining was first introduced to the shallower workings (I 80m) of Prince Colliery in the early 1980's. Phalen Colliery started longwall retreating in 1987 and since that time has extracted twelve panels. In 1993 there had been a total of eight longwalls varying in widths from 140-230m mined in Phalen Colliery that is on the Phalen Seam. Up to this point there were only minor ground control problems on the faces except for one of the earlier longwalls that was mining a split seam. There is some interaction on Phalen workings from remnant structures in the overlying Lingan and No. 26 Collieries which worked the Harbour Seam. Induced abutments loads along pillar edges have been observed and resulted in poor face conditions when mining the Phalen Seam. The ninth panel, 6 East was the first panel to suffer a major roof fall from the First Major Weighting. This was also the first panel to undermine a paleo sandstone river channel named the Lower Sandstone Unit (LSU). For the first time in Phalen's history subsequent longwalls began to experience periodic weighting events. The 6 East panel suffered a number of periodic weightings and on two occasions had to use foam cement to fill the cavities that resulted. On the next east side panel, 7 East, there were numerous periodic weighting events, but interestingly there was no significant First Major Weighting. 7 East was the first 260m wide panel and all others were 230m or less. This longwall was 3,400m long and began producing in December of 1994 and was still cutting coal in May of 1997. There were five significant roof fall events on this panel, three of which required foam cement to fill the cavities. Of these three the interruption to production varied from four days to seven months. There were definite precursors to each of the weightings including: 1) an increase in audible noise (termed bumping) on the face, 2) supports went rapidly into yield, 3) roof convergence increased, 4) water percolated from the face roof strata, and 5) severe spalling of the coal occurred resulting in increased tip to face distance. Longwall face weightings are a result of geomechanical factors and cannot be avoided However, the loss of roof control is a different matter and highly subjective to operational procedures. The causes of weightings, their magnitude and impact on the mining at Phalen have been investigated. The following factors have been identified as relevant to these occurrences. 1. The influence of pillars in the overlying Harbour Seam workings. 2. Location of the LSU relative to the Phalen Seam. 3. Thickness of the LSU. 4. Pressure arch effect from the adjacent gobs. 5. Poor operational practices on the longwall including: a) slow rate of retreat; b) inadequate supply of pump pressure to the hydraulic supports; c) premature yielding of the yield valves; and d) poor face alignment practices. This paper will review the events that took place on the 7 East longwall and show that the Lower Sandstone Unit is the primary cause of the weightings. However, other factors contributed to the loss of roof control and the formation of the roof cavities.

Jan 1, 1997

By Morgan M. Sears, Mark Van Dyke, Gamal Rashed, John Rusnak, Khaled Mohamed

"In 2016, room-and-pillar mining provided nearly 40% of underground coal production in the United States. Over the past decade, rib falls have resulted in 12 fatalities, representing 28% of the ground-fall fatalities in U.S. underground coal mines. Nine of these 12 fatalities (75%) have occurred in room-and-pillar mines. The objective of this research is to study the geomechanics of bench room-and-pillar mining and the associated response of high pillar ribs at overburden depths greater than 1,000 ft. This paper provides a definition of the bench technique, the pillar response due to loading, observational data for a case history, a calibrated numerical model of the observed rib response, and application of this calibrated model to a second site. INTRODUCTION Bench mining is a an underground mining technique typically applied to room-and-pillar mines where full seam extraction on development presents an unacceptably high risk of injury from high pillar ribs or where the mining equipment is not designed to extract the full seam thickness. To mitigate the increased risk associated with high ribs and slender pillars, a more modest thickness is extracted from the top of the seam on development. This is followed by grading the floor and recovering the bottom of the seam with or without extraction of the pillars during retreat mining. A mine located in Eastern Kentucky extracts two seams at depths ranging from outcrop to 2,000 ft. In some areas of the mine, Seam A and Seam B are close enough together to be mined simultaneously. Seam A (top) is mined on development 7 to 9 ft. high for the entire length of the panel. On retreat, as each pillar is extracted, the continuous miner is ramped down into the floor (Seam B), two pairs of Mobile Roof Support (MRS) units are set, and the pillars are extracted at the full mining height of 14+ ft. During the pillar recovery process, the floor is extracted in each entry, from a ramp initiated outby the retreat line, sequentially just prior to extracting the lifts from the pillars (see Figure 1)."

Jan 1, 2017

By Guy Reed, Russell Frith, Kent Mctyer

"Coal pillar design has historically been based on assigning a design factor of safety (FoS) or stability factor (SF) to coal pillars according to their estimated strength and the assumed overburden load acting on them. Acceptable FoS VALUES (have been assigned based on past mining experience, and at least one methodology includes the determination of a statistical link between FoS and probability of failure (PoF).The role of the pillar width-to-height (w/h) ratio has long been established as having a material influence on both the strength of a coal pillar and its potential mode of failure. However, there has been significant professional disagreement on using both FoS and w/h ratio as part of a combined pillar system stability criterion, as compared to using FoS in isolation. The argument is that, as w/h ratio is intrinsic to pillar strength, which, in tum, is intrinsic to FoS, it makes no sense to include w/h ratio twice in the stability assessment. At face value, this logic is sound.However, this paper will argue that there is a valid technical reason to bring w/h ratio into system stability criteria (other than its influence on pillar strength), as it is related to the post-failure stiffness of the pillar, as measured in situ, and its interaction with overburden stiffness.When overburden stiffness is bought into pillar system stability considerations, two issues emerge. The first is the width-to-depth (W/H) ratio of the panel, in particular whether it is sub-critical or super-critical from a surface subsidence perspective. As a minimum, this directly relates to the accuracy of the pillar loading assumption of full tributary area loading. The second relates to a reevaluation of pillar FoS based on whether the pillar is in an elastic or non-elastic (i.e., post-yield) state in its as-designed condition, as relevant to maintaining overburden stiffness at the highest possible level.The significance of the model presented is the potential to maximise both reserve recovery and mining efficiencies without any discernible increase in geotechnical risk, particularly in thick seams and higher depth of cover mining situations. At a time when mining economics are, at best, marginal, removing potentially unnecessary design conservatism without negatively affecting safety is of interest to all mine operators and is an important topic for discussion amongst the geotechnical community."

Jan 1, 2016

By William Kendall

"A tremendous amount of research, analysis, and engineering time is used to design a proper roof support system including the type, length, and location of the roof bolts. Unfortunately, since the roof bolts are being installed under unsupported roof, the exact location for the bolt holes cannot easily be determined and then marked onto the roof. The actual location where the roof bolts are installed is typically left to visual estimates by the operator. This frequently results in either (1) the operator overestimating the space between roof bolts and installing more bolts than required, thereby increasing cost and reducing efficiency; or (2) the operator underestimating the space between roof bolts and installing fewer bolts than required, thereby reducing safety, leading to potential roof failure or possible violations.A patented laser light grid system has been developed by J .H. Fletcher and Monitech, a South African Company, to aid in proper machine positioning in the heading and proper bolt spacing. The system can also show when an entry is over width, requiring additional roof support. The system is relatively simple and inexpensive. The concept is applicable across the full range of roof bolters from low to high seams and from single boom to multiple boom bolters. The system can be configured to meet most bolting patterns.The system consists of several very small 1 milliwatt, class 2, line type lasers that project a line onto the roof. The actual laser is 27mm in diameter x 47mm long (1"" x 1.8""). In South Africa it is approved as intrinsically safe and is mounted inside a 50mm diameter x 64mm long (2""x 2.5"") protective housing. In the USA, we are seeking an X/P approval and the laser will be mounted in a headlight enclosure 110mm diameter x 125mm long (4.3"" x 5""). Fifteen of the systems have been installed in South African coal mines with good results.The system has aided the mines in meeting the bolt spacing tolerance used in the Republic of South Africa, which is typically 15% of the nominal bolt spacing or 7 in for 4-ft bolt spacing. Fletcher has submitted the system to MSHA for approval in the US."

Jan 1, 2016

By Behdeen Oraee, Amirhossein Bangian, Kazem Oraee

"Determination of the optimum design of chain pillars has a significant effect on the economics and safety of longwall operations. Most pillar design formulae are based on empirical methods and supplemented by local experience. They therefore lack versatility of application under different geotechnical conditions.In this paper, in order to illustrate the shortcomings of the above, a typical real coal pillar in Tabas coal mine has first been studied and the conventional formulae have been used to determine the optimum dimensions. The results show that a wide difference exists between the predicted and the real field data. The Oraee-Hosseini formula has then been applied to this mine in order to determine the optimum design. The results from this formula demonstrate a close fit between the theoretical VALUES (and those produced by laboratory tests and in practice. It is further demonstrated that the wide discrepancy between the results obtained from the two formulae is attributed to the dissimilarities between geotechnical conditions of Tabas and the original regions whose data were used to devise the empirical formulae.It is finally concluded that the application of numerical simulation methods and experimental equations together with engineering judgment used by the mining design engineer, will provide the most accurate design characteristics.INTRODUCTIONLongwall is an underground mining method which has a high rate of production capacity and mechanization ability. This mining method, which is appropriately applied for soft rock fiatlying bedded ore bodies, gradually became a widespread mining method amongst European coal mines at the beginning of the 19'h century. It was then applied in some of the U.S. coal mines with the development of self advancing support mechanisms in early 1960's (Oraee, 2001).Underground coal production around the world using Longwall mining method doubled during 1990s. The main reasons for this improvement were: the high level of mechanization, increased 10 safety, adequate design of panels, and well designed ventilation systems (Peng, 2006)."

Jan 1, 2010

By Jessica M. Wempen

Differential Interferometric Synthetic Aperture Radar (DInSAR), a satellite-based remote sensing technique, has been demonstrated as a potentially practical method for measuring mining induced surface subsidence. Unlike traditional methods of subsidence monitoring, DInSAR has the capacity to generate subsidence data on a regional mining scale with a relatively high data density. Using DInSAR to evaluate subsidence over large regions with relatively long time scales has the potential to help quantify the impact of subsidence in the mining region, and provide a means for validating whole-mine geotechnical models. In this study, nine pairs of interferometric data from the Japanese Advance Land Observing Satellite (ALOS) were processed using DInSAR to generate displacement maps for a group of trona mines in southwest Wyoming. The data cover a time span from December 2007 to March 2011. The maximum subsidence for one of the mines totaled 1.3 meters for this period. Cumulative DInSAR displacement maps show the development of subsidence over time. In this mining region, surface subsidence is generated primarily by extraction of trona using retreating longwalls. Additionally, trona is extracted by solution mining, which also generates measurable surface subsidence.

Jan 1, 2014

By Andre Zingano

The coal seam strength and the failure criteria that represent the behavior of the coal seam are very important for mine section and pillar design. Additionally, mine section and pillar design take into account roof and floor layers, which form the roof-pillar-floor system. Therefore, underground ground control design begins, most importantly, with rock mass characterization. Another issue is the distribution or behavior of the coal seam strength for the whole mine area. Sometimes, the coal seam strength is assumed to be the same for an entire area, but this is not true because the coal seam is heterogenic and anisotropic, and also the coal strength is affected by faults and spacing between fractures. The objective of this paper is to demonstrate the use of the methodology for geomechanics characterization to determine the strength for the Bonito coal seam, and discuss the coal seam strength distribution around the entire mine area. The intact coal strength was determined by laboratory tests that were completed during the last 17 years, including triaxial and uniaxial strength tests. It was noted that there is a strong correlation between all laboratory strength tests with 90% confidence interval. The explanation for this coal seam strength variation is the presence of the discontinuities and their variation in quantity and quality at each location in the mine area, because the coal seam rock classification and its behavior will be affected by the quantity and quality of fractures.

Jan 1, 2014

By Muhammad Zaka Emad, Rangzeb Goraya, Muhammad Usman Khan

"Numerical modeling has been used extensively to assess the stability of surface and underground mines. Tabular, steeply dipping ore bodies are generally mined out by open stoping methods with delayed backfill. Cemented rockfill (CRF) is employed as a backfill material for narrow vein deposits with low production rates. Sublevel stoping methods with delayed backfill are employed to mine out steeply dipping ore bodies. Backfill is exposed to blast-induced vibrations and dynamic loading due to loss of confinement, which could lead to backfill failures. Backfill failures could influence the operating cost of a mining stope and the productivity of the entire mining project. This work shows a detailed overview of the factors contributing to backfill failure. A detailed literature review is presented along with case studies of longhole stoping operations from the Canadian Shield region for this work. The backfilled stopes are analyzed with the finite difference code FLAC3D. The literature review shows that the factors primarily responsible for fill failure are the strength of backfill, stope geometry, mining sequence, and blast-induced vibrations. INTRODUCTION Sublevel stoping methods with delayed backfill are popular in Canadian hardrock and metal mines. Backfill facilitates ground control and greater recovery of ore with pillar mining. It reduces wall slough, thus decreasing ore dilution from adjacent walls. The production of cemented rockfill (CRF) is simple; rock aggregates are mixed together with cement slurry and then placed in a mined-out stope. CRF has a low water content, thus it requires no additional drainage unlike some other backfill. Low water-to-cement ratio enables faster curing rate, hence a faster mining cycle can be achieved (Annor, 1999; Hassani and Archibald, 1998; McKay and Duke, 1989). CRF is generally placed in stopes from the upper sill drift using a truck or a load haul dump machine. Some of the problems associated with CRF are the moderate to high operational cost, the difficulty to get a tight filling, and segregation. Backfill failure is a product of many factors, such as cementation, particle size distribution, placement method employed, water quality, segregation, and blast-induced vibrations. The problem of segregation in aggregates has been observed when aggregate is dumped from a backfill raise (Meech, 2012; Indiana DOT, 2013). Segregation becomes unavoidable when the aggregates are not properly sized (Yu and Counter, 1983; Stone, 2007; Yu, 1989). The exposed backfill zones will contribute to ore dilution due to backfill when subjected to dynamic loading due to fill failures. This paper presents a detailed literature review and numerical modeling results of a mine backfill, along with case studies from longhole stoping operations. The backfilled stopes are analyzed with the finite difference code FLAC3D (Itasca, 2017). The literature review shows that the primary factors responsible for fill failure are the strength of backfill, geometry of stope, sequence of mining, and the vibrations induced by blasting operations."

Jan 1, 2017

By S. Paul Singh

"The long-term viability of seismically active and/or deep mining operations hinges upon the industry's ability to maintain profitability in a climate of increasingly difficult conditions, escalating operating costs and fluctuating metal prices. Within this context, it is prudent to explore mining techniques that could provide means for safer and more profitable extraction of seismically active and/or deep seated deposits that are vital to the long term survival of the industry.The first step was to examine Penetrating Cone Fracture (PCF) and other relevant concepts with the objective of semi-continuous mining in deep underground hard rock mines. This was followed by an assessment of the current conventional drilling and blasting practice. Thirteen blasts were monitored in five different seismically active workings of an operating deep mine. The main concerns during the current drill and blast practice were identified.On the basis of the literature review, three short round blasting techniques were short listed for further review. These techniques were evaluated based upon the available literature and discussions with the persons associated with their applications. Justification, requirements and major challenges for the application of short round blasting have been discussed in this paper. Suggestions for improving the current drilling and blasting practice have also been outlined.INTRODUCTIONRock fragmentation is the key to mineral excavation and production. Increasing working depths, environmental concerns and trends towards continuous mining necessitate the development of new and improved rock breakage methods.The excavation of hard rocks is still dominated by the sequential routine of face preparation, drilling, charging explosives, blasting, ventilating for fume and dust removal, mucking and roof support. Worse still, drilling and mucking require specialized equipment that fills the end of the heading so that no other operation can be performed and the equipment must be removed from the face to protect it from fly rock."

Jan 1, 2010

By Liang Yin-Huai

In Fuxin Coal Mines, there are more than 20 million tons of coal buried under seasonal streams. The coal seams are mostly shallow. We have mined more then 50 mining blocks distributed in 5 coal mines. Their natural conditions are different, and the consequences are also more or less different. However, no stream-water-inrush accidents under regular mining conditions are the same. There were 3 exceptions. They were caused by unexpected roof caving which made valleys or alluvia subside as funnel-like cavities and let in inrush of stream flow. The key to our success in mining shallow under-stream coal seams, according to our analysis, is that valleys or alluvia subside gently and basically evenly with contractible tension fissures and that fissures both in valleys or alluvia and in rock seams are blocked up or sealed by cohesive deposits either from alluvia or rock. This paper treats: (1) some typical illustrations of mining shallow coal seams of different occurrences under streams of different sizes, flowing capacities and valley structures, (2) observations of the height of caved and fissured zones and subsidence of valleys or alluvia, (3) observations of underground water flow before, during, and after mining and the fluctuation with respect to stream flow, (4) observations and analyses of blocking up of fissures caused by mining, and (5) feasibility of mining shallow under-river coal seams.

Jan 1, 1990

By E. Hosca

Alternative tailgate loading conditions due to conventional and conventional/yield pillar combinations were evaluated to define roof loading. In order to isolate different loading situations, the tailgate entry was considered as part of the roof-pillar-floor system, which is controlled largely by the structural integrity of each member. A data bank of case studies was compiled, which contains details of roof and floor lithology, structure, support, and mining data, including any failure modes. The range of loading conditions that any tailgate can be subjected to was identified to form the basis of numerical modeling. Numerical modeling was then conducted on tailgate openings to determine roof, floor, and rib responses, including failure modes to a variety of loading conditions. Trends developed from the numerical modeling were modified using field data to form the basis for support evaluation and application. The effects of support were modeled numerically to determine optimum load capacity and points of application for reducing the potential for entry failure.

Jan 1, 1994

By John D. VandeKraats

Yielding rock bolt systems have been developed to provide ground support while accommodating shifting, creeping, or swelling ground movements. The Dywidag Systems, Inc. (DSI) Slip Nut System is one such system. It has been tested in the laboratory and installed and monitored in the interbedded halite and anhydrite at the Waste Isolation Pilot Plant (WIPP) since 1994. The Slip Nut System is installed on a point anchored threaded bar or on a threaded bar coupled to a cable bolt. At a pre-engineered load the nut acts as a die and cuts through the thread on which it rests, thereby reducing the load and coming to rest on the next thread where the process repeats. Two types of laboratory tests were performed using slip nuts on DSI's threaded bars and their Tensionable Cable bolts. Straight pull tests exceeding 0.3m (1 ft.) of displacement were performed on the systems. Also, offset tests were performed on these bolt systems in a test frame designed to simulate WIPP geologic conditions. A room scale test area consisting of 186 threaded bars began in 1994. Select bolts were instrumented to track bolt load. All bolts were tracked through time for operation. Through three complete years since installation over twelve slips, corresponding to approximately 0.15m (6 in.) of ground movement, have been observed in some areas. Since installation strata offset has exceeded 0.08m (3 in.) at a supported clay layer in the roof. No bolt failures have been observed. Slip loads observed underground generally approximate those observed in the lab. To date, the slip nut systems tested and installed have performed as expected.

Jan 1, 1998

By Winton J. Gale

The subsidence over a longwall panel at Tahmoor Mine in the Southern Coalfield of NSW, Australia, was found to be approximately twice the size it had been in previous measurements. An investigation into the potential causes was conducted using computer modeling together with hydrological characterization and detailed geotechnical characterization of the strata. The abnormal subsidence was found to be consistent with localized weathering of joint and bedding planes above a depressed water table adjacent to an incised gorge. The study showed that other factors such as variation in stress field, joint zones, variation in rock strength and topographic factors did have sufficient impact to induce the abnormal subsidence. The results have significant implications to subsidence prediction in areas that may be prone to the phenomenon found at Tahmoor. Key indicators of the potential for this form of abnormal subsidence are presented.

Jan 1, 2011

By Jessica M. Wempen, Michael K. McCarter

"Differential Interferometric Synthetic Aperture Radar (DlnSAR), a satellite-based remote sensing technique, has potential application for measuring mine subsidence on a regional scale with high spatial and temporal resolutions. However, the characteristics of Synthetic Aperture Radar (SAR) data and the effectiveness of DlnSAR for subsidence monitoring depend on the radar band (wavelength). This study evaluates the effectiveness of DinSAR for monitoring subsidence due to longwall mining in central Utah using L-band (24 cm wavelength) SAR data from the Advanced Land Observing Satellite (ALOS) and X-band (3 cm wavelength) SAR data from the TerraSAR-X mission.In the Wasatch Plateau region of central Utah, which is characterized by steep terrain and variable ground cover conditions, areas affected by longwall mine subsidence are identifiable using both L-band and X-band DlnSAR. Generally, using L-band data, subsidence magnitudes are measurable. Compared to X-band, L-band data are less affected by signal saturation due to large deformation gradients and by temporal decorrelation due to changes in the surface conditions over time. The L-band data tend to be stable over relatively long periods (months). Short wavelength X-band data are strongly affected by signal saturation and temporal decorrelation, but regions of subsidence are typically identifiable over short periods (days). Additionally, though subsidence magnitudes are difficult to precisely measure in the central Utah region using X-band data, they can often be reasonably estimated.INTRODUCTIONDifferential Interferometric Synthetic Aperture Radar (DlnSAR) is a satellite-based remote technique that can be used to measure surface displacement over large regions with high spatial resolution. Under good conditions, displacements can be measured with centimeter to subcentimeter accuracy (Buckley, 2000; Massonnet and Feig!, 1998). DlnSAR also has high temporal resolution, and imaging periods typically range from 10 to 50 days (Rosenqvist, Shimada, and Watanabe, 2004; Roth, 2004). In the last two decades, the application of DlnSAR for mine subsidence monitoring has been demonstrated in coal basins in Europe, Australia, China, and the United States (Camec and Delacourt, 2000; Ge, Chang, and Rizos, 2007; Ge et al., 2008; Ismaya and Donovan, 2012; Ng et al., 2010; Perski, 2000; Perski and Jura, 2003; Popiolek and Krawczyk, 2006; Wegmuller et al., 2005; Wright and Stow, 1999; Zhao et al., 2014; Xinglin et al., 2014). Overall, these studies have demonstrated good data resolution, strong relationships between mine development and subsidence, and reasonable agreement between displacements measured by DinSAR and displacements measured by conventional surveys."

Jan 1, 2016

By Douglas Tesarik, Mark K. Larson, Habte Abraham, Heather E. Lawson

Dynamic failures, or "bumps", remain an imperative safety concern in underground coal mining, despite significant advancements in engineering controls. While many factors have been empirically linked to the occurrence of dynamic failure events, identifying a consistent, repeatable set of criteria within a field setting has proven elusive; conditions generally associated with dynamic failure might produce an event at one site, but not another. Conversely and more troubling, dynamic failure could occur where relatively few of these factors exist. The presence of spatially discrete, stiff roof units, such as paleo channels, are one such feature that has been linked to the occurrence of dynamic failure events. However, an empirical stratigraphic review investigating the relative frequency of discrete units in bumping versus non-bumping deposits indicates that no significant difference exists based on this criterion alone, and that instead an apparent relationship exists between reportable bump history and the overall character of the host rock with respect to stiffness. Due to the complexity of the bump problem, however, these results are not conclusive, as they do not take into account any variable other than the presence or absence of stiff members in the roof lithology; To weight the relative impact of changes in a single variable, such as the thickness or location of sandstone members, it must be examined in isolation-i.e. in a setting where all other variables are held constant. Numerical modelling provides this setting, and the effects of variability in a stiff discrete member in a hypothetical longwall mining scenario are investigated within the context of three stratigraphic "types'', as determined by the ratio of stiff to compliant stratigraphic members; Compliant, Intermediate and Stiff A modelling experiment examines changes in rupture potential in stiff roof units for each stratigraphic type as discrete unit thickness and location are manipulated through a range of values. Results suggest that the stiff-to-compliant ratio of the host rock has an impact on the relative stress-inducing effects of discrete stiff members. In other words, it is necessary to consider both the thickness and the distance to the seam, within the context of the host rock, to accurately anticipate areas of elevated rupture induced hazard; acknowledging the presence of a discrete unit within the overburden in general terms is an insufficient indicator of risk. Through modelling of anticipated changes in the placement and dimensions of discrete units within their stratigraphic setting, elevated rupture-induced bump hazard can be anticipated on a case by case basis. Were similar modelling studies conducted at mine sites in tandem with tracking of problematic discrete stiff units, areas of elevated rupture risk could be anticipated in advance of mining. Developing this predictive capability beyond identifying rupture potential in discrete roof members is essential to the eventual elimination of dynamic failure related worker injuries and fatalities. As stress is a necessary component in the occurrence of dynamic failure events, this finding helps to refine our understanding of the role of individual stiff, strong roof members in bumping phenomena, and suggests that a more holistic view of overburden lithology, combined with site-specific numerical modelling, may be necessary to achieve greater miner safety.

Jan 1, 2016