Search Documents

By Matthew K. Coy, Paul N. Worsey

The work described in this paper comprised the master’s thesis work of the primary author and was conducted at the Missouri S&T experimental mine. The objective was to determine if rubber tractor treads could be used as an alternative material for blasting mats. These treads are made from steel cable and vulcanized rubber and are very tough. However, once they reach the end of their life on mobile equipment, they are destined for a landfill, or dump site, because they are too tough to recycle. A potential alternative use for them is as blasting mats. Several discarded treads were obtained from Kolb Grading in St. Louis.

Jan 1, 2015

By Terry Matts, Bruce Ripley, Clark Fletcher, Paul Rapp, Stan Holtby, Jim Dent

The Stave Falls Project of BC Hydro, situated 65km east of Vancouver, BC, Canada, involved the construction of a new two-unit 9OMW hydro-electric facility to replace an existing powerhouse. The final phase of the intake excavation consisted of a plug blast to break the channel through into Stave Lake. The plug consisted of a rock and till wall topped with a fill cofferdam, about 51m wide and between 8 and 12m high. Total rock volume was approximately 2600m3, overlaid with about 4600m3 of till/fill. This paper describes the methodology and practical techniques used in planning and loading the blast, and the precautions taken to protect the new and existing structures and equipment. Blasting of the plug by the normal method using downholes would have required the placing of extra fill and much drilling through casing, so the contractor made the decision to drill horizontal holes from the dry, downstream side. Because of poor rock conditions, all 183 holes had to be drilled oversize at 3.5” dia. and fitted with 2.5” id. plastic pipes to keep them open. Hole lengths ranged from 2.5 to 18rn, with a pattern of 1.5m spacing and l.Om burden (with the holes slightly fanned vertically). Because of significant water exposure, a film-packaged emulsion explosive was used, placed using a pneumatic cartridge loader for maximum borehole compaction. The powder factor averaged 1.3kg/m3 (2.21bs/yd3, rock only). An initiation system of combination surface/downhole delay shocktube units was employed, with double and triple redundancy. The maximum number of holes firing in any 8ms window was limited to three (to minimize vibration), while the whole sequence was fully activated before the first hole fired. All shocktube connections were secured and covered over at the foot of the rockface before flooding the excavation downstream of the plug prior to the shot, To protect the powerhouse gates from hydraulic shock, all hole collars were grouted and an air curtain was provided. The blast was completely successful. A maximum vertical displacement of 6m was recorded, but no flyrock was evident. Readings for peak over-pressure and vibration were well below the allowed limits. Mucking proved to be easy, with fine fragmentation, full pull, and no tights.

Jan 1, 2000

By Andrea Francioso, Roberto Folchi

In order to comply with the latest European Highway Standards, the highway Salerno - Reggio Calabria, in southern Italy, had do be widened and upgraded to reduce its vulnerability to earthquakes. Reinforced concrete viaducts, no longer needed for the new road, had to be demolished. Many bridges still to be used for the highway required refurbishment due to 50 years of wind, frost and salt corrosion. This re-furbishment and new construction had to be carried out simultaneously. To keep the highway open dur-ing the renewal process, all traffic was directed to one side of the road. Demolition was conducted ex-tremely close to operational roadways and viaducts, as close as only 2 cm (0.8 in). Care had to be taken to ensure that the stresses (vibration levels), resulting from the demolished pylons and decks hitting the ground, were below the no-damage thresholds for the nearby acceptors (structures receiving the vibra-tion stresses). These structures included bridges, houses and buried pipelines (water, oil and gas). In some cases, care also had to be taken to preserve the existing pylons supporting decks that were being demolished; since the same pylons were going to be used for the new viaducts (bridges). New continu-ous decks in weathering steel replaced the old reinforced concrete decks.

Jan 1, 2013

By G. Walsh, M. T. Wild

In this paper the performance effects of linear shaped charges will be discussed. Different sized charges were tested and reviewed based on their performance used with a typical detonation method vs. detonation with a line wave generator. The goal of the project was to determine if the linear shaped charge had better performance with an ideally linear wave moving through it, verses a swept wave that is currently used. A line wave generator is a flexible sheet explosive formed into a triangular shape with holes placed in strategic places to cause a detonation wave to become linear across the width of the triangle. A standard linear shape charge with a detonator in the side of the charge was be detonated against a witness plate to get a standard depth of penetration. A second standard linear shape charge with a detonator connected to the top of a line wave generator, the line wave generator placed on top of the linear shape charge, was be detonated against a witness plate to get a comparison depth of penetration. All charges had a standoff 1.5 times the width of the cavity, allowing the data to be compared to the control charge. Computer modeling was intended to be used to predict the results from testing these designs in the field. The actual results were compared among themselves.

Jan 1, 2011

By Josh Calnan, Zach Agioutantis, Daykin Schnell

Damage complaints are a common occurrence related to blasting activities, specifically when blasting operations occur near residential areas. These complaints are often associated with ground vibrations from blasting. It is important for blasters and engineers to understand the potential for ground vibrations to damage residential structures to properly design blasts and appropriately address any damage complaints that arise. A review of the most recent studies of blast vibration damage thresholds for residential structures is conducted to provide a baseline understanding of blast damage potential and mechanisms. Gaps in research and understanding blast vibration damage potential are identified. Research in further understanding damage potential is presented and focuses on studying the impact of high-range ground vibrations generated from full-scale, nearfield ground vibrations from blasting on a residential structure. Specific impacts of the high-range ground vibrations reviewed as part of this research include damage to the block wall basement, global strain, rotational forces, crack generation, and crack extension in a residential structure. Planning and methodology for intentional full-scale, nearfield blasting at a limestone quarry within close proximity to a residential structure owned by the quarry are presented. Conclusions discuss the objectives and optimized layout of the ongoing data collection for the proposed research and analysis. Future potential work related to further understanding blast damage mechanisms and thresholds are also discussed.

Jan 26, 2026

By Tyler Acorn

In December of 2009 an estimated one million ton slope failure activated a 10 million ton mass impacting use of the main ramp system in the Newmont Gold Quarry pit. The failure left behind a 400 foot (122 meters), vertical to sub vertical scarp feature and shut down production in the lower benches of the pit.

Jan 1, 2011

Currently there exist several explosive quantity-distance (Q-D) rules variously exercised by most countries to protect personnel and property against the effects of accidental explosions. These regulations apply to manufacture, transport and storage of explosive products. This paper reviews the technical basis behind these regulations, as they apply to commercial and military explosives. The characteristics of a blast wave and missiles issuing out of an explosion site and their role in determining the level of damage to a target are discussed. The need for further research on the effect of detonation of charges of non-standard geometry, and under confined conditions such as tunnels is discussed. The challenge in estimating the net quantity of explosives involved and calculation of its TNT-equivalency is also highlighted.

Jan 1, 2011

By Travis A. Davidsavor, Charles Dowding, David A. Provost, Yonggang Gou

This paper compares measured blast induced strains on operating, full scale, buried pipelines with three similar past studies. The recently performed study represents realistic and modern pipeline blasting techniques combined with modern data acquisition. The evaluation compares measured PPV and strain, as well as calculated stress, at equivalent scaled distances.

Feb 1, 2020

By J. A. Sanchidrián, P. Segarra, S. Gómez

Blasting is a common activity in mining that can cause significant damage in the remaining rock mass. The most commonly used method for predicting vibrations is the Swedish or Holmberg-Persson approach. It is a simple and fast method that uses empirical formulation to estimate the vibration levels based on the explosive charge weight, distance to the source, and other parameters. However, it has limited accuracy and does not consider the effect of free surfaces or other boundary conditions. On the other hand, recently developed methods as the full-field solution (FFS) can provide more accurate predictions of vibrations due to excitations provoked by cylindrical columns of explosive, but the inclusion of free surfaces in analytical methods is a challenging problem. This paper presents a new approach that includes free surfaces in the FFS to predict vibrations analytically in the near-field. The main obstacle to including free surfaces in the FFS was the belief that the solution was non-decoupleable in P- and SV-waves separately. The Heelan's approach was previously used to decouple them, but it only provides valid radiation patterns in the far-field and does not account for intrinsic attenuation. In this paper, we address this problem successfully, allowing for the inclusion of free surfaces in the FFS.

Jan 1, 2024

By Kirk Yeager

All explosive formulations display some sensitivity to heat. A common technique utilized to measure an explosive’s response to thermal stimulation is differential scanning calorimetry (DSC). As DSC analysis is run on quantities of material easily handled in a laboratory setting, and is relatively inexpensive, it tends to be one of the more predominant tools utilized to determine potential thermal hazards of energetic materials. The analysis of energetic materials via DSC provides unique challenges, as both large energy outputs and significant production of gaseous products result from their decompositions. In addition, the unique thermal decomposition characteristics of ammonium nitrate (AN) based materials have also created difficulties in DSC analyses. A wide variety of techniques have been developed to study the decomposition of explosives. Traditionally, sealed glass capillaries were utilized to house samples. Recently, the introduction of specialty cells designed to withstand high pressures has enabled new sampling techniques to be developed. Analyses of explosives with both traditional and “high-pressure” cells will be compared and contrasted. Lessons learned about the application of both techniques towards analyzing thermal hazards such as incompatibilities will be presented. Inconsistencies in the results displayed during analyses of AN-based explosives will be highlighted. Recommendations on the best approach for analyzing the more problematic AN formulations will be given.

Jan 1, 2000

By Mario Dobrilovic, Zvonimir Ester, Vinko Skrlec, Vjecislav Bohanek

The first public garage in the city of Dubrovnik has been built in highly urbanized area, on location Ilina Glavica. The excavation of the building pit has been done partly by construction machinery, i.e. by hydraulic hammer for excavations and partly by drilling and blasting. In the vicinity of the building pit there are houses, buildings and two schools. Drilling operations and blasting have been performed during the working hours while regular school classes have been held and activities in other buildings took place. The nearest structures are some 5 to 10 meters (16.4 to 32.8 ft) away from the building pit, which makes it even more difficult to perform blasting operations in the urban environment. For the purpose of determining safe and permissible oscillation velocity limits, i.e. the proportion of seismic effects of blasting, a trial blasting has been conducted. The permissible mass of explosive charge has been determined by original method respecting the requirements of existing standards (ISO 4866, DIN 4150, US BM 8507), which determine the permissible oscillation velocities in relation to their frequencies. According to measuring results of the oscillation velocity during the test blasting the design parameters of blasting field have been corrected and zones have been established within the excavation area considering the possible effect of blasting to the building pit environment. Further blasting operations have been performed in stages, in smaller blasting fields with deck charge within a blast hole while respecting the requirements of the transport possibilities for the blasted rock mass within the building pit and performance of control measurements of oscillation velocity for each blasting. Through application of all the protection measures, design solutions and systematic control of performance of activities the complete excavation by blasting has been completed without any damage on neighboring structures/buildings. This article presents these solutions and methods for reduction of seismic impact of blasting to the environment.

Jan 1, 2009

By H. S. Venkatesh, G. Gopinath, R. Balachander, G. C. Naveen

Punatsangchu Hydroelectric Project Authority is constructing 1020 MW underground hydroelectric project in Bhutan. The project envisages construction of concrete dam, Desilting Chamber, Head Race Tunnel, Power House Complex and Tail Race Tunnel. Tunneling is one of the major activity in any underground projects as they are driven for multiple activities. By and large the tunnels are a major part of connecting networks from surface to caverns/underground working sites. Many tunnels in hydropower project are part of water conducting systems and one such important tunnel is the Tail Race Tunnel in this project and had to be excavated in thinly foliated rockmass conditions by D&B method.

Feb 1, 2020

By Dipankar Gorain, A K. Vishwakarma, Vivek K. Himanshu, Murari P. Roy, Shubham Singh, R S. Yadav

The industrial establishments of a power plant consist of many important structures viz. cooling tower, wagon tippler, track hopper, plants and offices. The leveled foundation is the utmost need for erecting these structures. The leveling of the foundation is done by rock excavation, when the establishments have to be setup in hilly/rocky areas. Drilling and blasting is the cheapest and most dominant method of rock excavation. However, this method has associated hazards in terms of blast induced ground vibration, air overpressure, flyrocks etc. The foundation work and erection of the industrial buildings are done in parallel to achieve the faster construction of the establishment. The challenges to reduce the induced hazards in such cases are more. This paper presents a case study on the controlled blasting method devised for the rock excavation for construction of 2 × 660 MW Obra-C thermal power plant. The foundation work for this power plant was made by excavation of Dolomitic rock. The excavation work was performed in the proximity of the existing residence of the local people and Obra market. With the advancement of project, the excavation was also performed in the proximity to the ongoing construction work of various industrial buildings. Accordingly, the controlled blasting pattern was devised suitable to the specific sites. The pattern consisted of variations in blasthole diameter, burden-spacing, maximum explosive charge per delay, total explosive in a blasting round, initiation system and direction of initiation. The suitable muffling arrangements were also used, when the blast was conducted in the close proximity to the structures. The initial blasting pattern was established by analysis of blast vibration wave propagation characteristics. Thereafter, the final pattern was adopted for the safe excavation at the site. The safe excavation for the foundation work of this power plant has been completed successfully based on the devised controlled blasting pattern.

Feb 6, 2023

By Reinhold Daykin, Piers Wendlandt, Nathan Rouse

Drilling and blasting are key components of every hard-rock (i.e., metal/nonmetal/coal) mining operation. Well-executed and maintained drilling and blasting can have a major positive impact on the overall success of such operations. This case study presents the implementation of a new drill and blast engineer position and systematic improvement of the drill and blast operations at a surface metal mine.

Feb 1, 2020

By Michael Weaver, Dale L. Ramsey

The Pinkerton Tunnel open cut project is part of the National Gateway Clearance Initiative improvement project to achieve a minimum of 21 feet of vertical clearance along CSX Transportation rail corridor so that double-stacked intermodal railcars can be transported between mid-Atlantic states and their ports to midwest markets in the U.S. This project involved drilling and blasting of 1.2 million bank cubic yards of rock over a 14 month period while maintaining rail traffic of two passenger and 38 freight trains daily. See story and photos, page 6.

Jan 1, 2015

By Michael Weaver, Dale Ramsey

Description of Project: The National Gateway Clearance Initiative is an improvement program to achieve a minimum of 21 feet of vertical clearance along CSX Transportation Inc’s (CSX) rail corridor so that double-stacked intermodal railcars can be transported between mid-Atlantic states and their ports to midwest markets.

Jan 1, 2014

By Roger L. Keller, John Dean Smith

The Amax Coal Company's Ayrshire Mine in Southern Indiana is faced with one of the toughest blasting applications concerning vibration in the nation. As a means of maintaining regulatory compliance the operation elected to exercise the option of frequency analysis. A site-specific computer processing program which suggests ideal delay interval ranges for the lowest vibration was utilized.

Jan 1, 1987

By Regina Rocha, Miguel Humpire

One of the challenges within unitary mining operations is blasting, which has a significant downstream impact on the following processes, which is why mining companies ensure the results of the blasting process through joint work with explosives specialists’ companies.

Feb 6, 2023

By John C. Brulia

The IME member companies, the ISEE along with its chapter organizations, the Federal, state and municipal regulatory agencies, and the industry consultants and suppliers have developed safety equipment, provided safety guidelines, promulgated safety-oriented regulations, and conducted safety training for blasting personnel in an effort to reduce explosives-related accidents.

Jan 1, 1994

By Greg Quinn

After a long week of work in Colorado Springs this past July, I was looking forward to flying home to start a long anticipated family vacation. As I grabbed my seat on the plane, a man sitting next to me innocently inquired, to the row as a whole and not to me in particular, “I wonder what the weather will be like in Phoenix”? To most people, this is a common (maybe the most common) topic of casual conversation. To a meteorologist that just dealt with six thunderstorm delays at a major golf event over 4 days, well, lets just say the smirk on my face said it all. After giving my flight mate a detailed forecast and a short explanation on why I would know such information, I sensed, correctly, the inevitable follow up question was coming. “Why would you need a meteorologist at a golf tournament?”

Jan 1, 2012