Search Documents

By Melvin A. Sannes

The Pinson Mine has several different rock formations, running throughout the pits. The main types of material found are Alluvium, Shale and Limestone. In some instances, all three can be found within one blast pattern. Several areas have broken material, which makes it very hard to drill and to shoot. If not timed and loaded correctly a lot of the explosive energy is lost through the broken material.

Jan 1, 1998

By Erica Lorenzo García, Benjamín Cebrian Romo, Antonio Morato Medina

This paper presents the results of a preliminary study on blast-induced vibrations conducted at a Radioactive Waste Storage Facility, located in Spain. The study was undertaken as a preparatory step prior to the blasting operations required for the construction of a new platform located near critical infrastructure housing very-low, low and intermediate-level radioactive waste. The primary goal was to establish a site-specific vibration attenuation curve to safely determine allowable explosive charges based on their distance to sensitive structures. The study followed the criteria defined in the UNE 22.381-93 standard, which regulates permissible vibration levels for different structural typologies. In this case, the existing facilities were classified as Type III structures, given their heightened sensitivity to vibrations. Two experimental campaigns were conducted. Test 1 consisted of a series of 10 individual blasts with increasing charges, monitored by five strategically placed seismographs to record seismic wave propagation and determine the attenuation parameters via regression analysis. Test 2 simulated a production blast using operational charges of 41.7 kg (91.93 lb), applying different delay sequences (42 ms and 25 ms) between holes to assess wave interference, resonance, and constructive effects. Data analysis showed that the longitudinal component dominated vibration transmission, and the predominant frequencies in the most critical zone ranged between 18 and 20 Hz. Based on these values, a conservative peak particle velocity (PPV) limit of 4.75 mm/s (0.19 in/s) was established for blast design. The recorded vibration levels during the tests remained within regulatory limits, with maximum values of 2.35 mm/s (0.09 in/s) and 2.86 mm/s (0.11 in/s) for the sequenced blasts, and peak acceleration of 0.0464g.

Jan 26, 2026

By Rolf R. Schillinger

Subject of the paper are blasting vibrations as sources of environmental molestations including acceptance level,complaint level and damage level as well. Besides, the subject shows a comparison of international regulations and their problematical aspects. In consideration of blast induced immissions the subject shows that human annoyance has become an important place in blasting works. It provides a solution proposal how to minimize environmental effects of blasting works.

Jan 1, 1996

By Norman Paley

A blasting project was undertaken at the Teck Alaska Red Dog Mine to determine the extent that Semi-Autogenous Grinding (SAG) mill throughput could be increased by using electronic detonators. The Julius Kruttschnitt Mineral Research Centre (JKMRC) blast fragmentation, jaw crusher, and SAG mill breakage models were used to relate changes in the blast fragmentation measured with the SPLIT image analysis system to the SAG mill performance. For optimum performance a SAG mill requires a particular size distribution; a number of large rocks to facilitate breakage by impact, as few as possible middle size rocks that become critical size, and the maximum fines which will pass quickly through an open-circuit mill. Physical constraints of drill and charging equipment size limit the extent that pattern geometry can be changed, and the powder factor increased, to maximize fines. However, a growing number of studies have shown that the use of electronic detonators can lead to increased fragmentation and greater muckpile uniformity, providing an alternate means of increasing primary breakage by blasting. Unfortunately results in the literature rarely quantified the changes to the fragmentation distribution. The measured gyratory crusher fragmentation of 2,750,000t of ore was used to compare stockpiles constructed from shots using pyrotechnic detonators to those using Orica i-kon electronic detonators. In the first stage of the study, stockpiles shot using 25 ms inter-hole timing with pyrotechnic detonators were compared to stockpiles shot using the same inter-hole timing with electronic detonators. In the second stage of the study, stockpiles shot using 17 ms inter-hole timing with pyrotechnic detonators were compared to stockpiles shot using 8 ms inter-hole timing with electronic detonators. When electronic detonators were used with the inter-hole timing kept constant, fragmentation uniformity was slightly increased, but mean fragment size increased by 20%. When electronic detonators were used with faster inter-hole timing, fragmentation uniformity was slightly reduced, but mean fragment size decreased by 30%. Modeling was used to determine the SAG mill throughput which could be expected from this change in fragmentation to determine the pairs of pyrotechnic and electronic blast pattern geometries that would provide similar throughput. The economic benefit from the electronic detonator shots was calculated to assist in determining the optimum blast designs for their use.

Jan 1, 2010

By August Ferraz Ribeiro, Guilherme Dias Mendona, Paula Henrique Lisboa, José Silvio Corsini

Correct slope adhesion is related to the conformity of the slope’s real geometry to slope planning. It is very important in mining because slope design has economic and safety implications. Slope design conditions can interfere with mining waste and ore proportion. Without a correct wall, the development of the mine can be hindered, which can reduce the amount of ore available. Furthermore, correct slope design reduces the possibility of melting and allows traffic with equipment and people in the mine. However, defining the wall is a more complex work as the characteristics of the rock require the use of blasting techniques. Therefore, Enaex Mining Technical Solutions (EMTS), in partnership with the engineering team at the Chapada Mine, at Lundin Mining, has developed this study in order to increase slope adhesion. The basis of this study is a near-field vibration test, which enables the creation of vibration attenuation law, and a seed wave damage model has allowed the characterization of the rock present at the Chapada Mine. Then, we could compare the model result to the real slope adhesion achieved with the buffer technique used in the mine. Therefore, it was possible to relate the real result to the model result.

Feb 6, 2023

By Harry Thompson

In using explosives to blast stumps from the ground in order to prepare it for farming, it is comparatively easy to place the charge under a stump having a semitaproot or a lateral system of rooting by boring or digging a hole in the earth to a point under the center of resistance and deep enough to give the desired effect.1

Jan 1, 2015

By R W. Thomas

This paper explores the possibilities of generating radical improvements in the drilling costs and productivity of blastholes through the efforts of integrated teams as opposed to traditional customer/vendor relationships.

Jan 1, 1996

By Mark Fritzen

Drilling and blasting near residential or business inhabited areas may expose people to blast induced vibration. Many of these people have never been exposed to blast vibration and airblast which can cause a variety of reactions ranging from indifference to anger. Blasting contractors seeking to minimize the impact of blasting to neighbors of the project will plan for a public relation plan which begins at bid time. The public relations plan cost will be included in their proposal and a variety of methods may be included including, door to door contact, letters, pamphlets, telephone calls, and the use of an independent consultant to conduct a pre-blast survey. By raising the awareness of neighbors to a blasting project the blasting contractor may reduce the anxiety and stress of unannounced blasting vibration and airblast. This helps everyone associated with the project from the project owner(s) to the blasting contractor.

Jan 1, 2000

By Miguel Humpire Huamani, Gustavo Huerta Valer, Jorge C. Cárdenas Miranda

As part of the continuous improvement and increase productivity to achieve the mining and extraction plan of a low-grade open pit copper operation, alternatives are required to expand the blast pattern to maximize drills and steels resources along to ensure the fragmentation results for the process plant with volumes from 500k tons of broken material per day. Therefore, the application of aluminum based ultra-high energy explosives was an alternative to achieve the objective of expanding the production pattern by 34% while maintaining energy factors levels along with the distribution of explosive and the application of the pocket charge in the stemming level, reducing the load factor, maintaining the fragmentation results in P80 and increasing the percentage of fines less than 1.0 in (2.54 cm). An important development to ensure the supply and perform successfully blasthole loading was the implementation of a supply system with pre-blending (aluminized emulsion) which is stored in silos and load through factory trucks. In the field we ensured optimal initial and final density levels with chemical sensitizer to perform the most fracturing work in the rock, complementary evaluations were performed to predict flyrock and define safe equipment evacuation radiuses along with advanced vibration monitoring for the sustainability of the mine.

Feb 6, 2023

By Lon Santis

In 1923, Ralph Assheton compiled a report for the Institute of Makers of Explosives (IME) on accidental explosions in manufacturing plants. The report chronicles the type and amount of explosive involved in the event and the effects and distances to nearby buildings and workers for over 100 events from 1880 to 1916. Apparently, this report was never published but served as the origin of the IME’s first intra-plant distance table published in Pamphlet No. 3 in 1926. The effort was a parallel effort to the IME’s development of the American Table of Distances. The intra-plant distance table has never been changed by the IME and follows the US Department of Defense (DoD) standard very closely. This paper freshly compiles the data from the 1923 report and analyzes it with modern methods not generally available in 1923. Interestingly, the analysis indicates that the original intra-plant distance tables were established primarily to protect workers from serious injury and that preventing propagation was a side benefit. The data shows that a strong relationship exists between the probability of injury and the traditional K-factor. The data indicate that people in the open are better protected than those inside structures and that barricades reduce risk close to an event. Individuals at the intra-plant distance had a 95 percent chance of receiving no worse than a minor injury. A comparison of the data to explosive event consequence models indicate the models are overly conservative in regards to risk inside inhabited building distances.

Jan 1, 2010

By Shadrack Nuamah, Erik Westman, Bright Afum, Jesse Addy

Rock fragmentation is the most critical aspect of hard rock production blasting due to its significant impact on drilling and blasting costs and the economics of subsequent loading, hauling, and crushing operations. This study analyzes current cost trends in the drill and blast operations of an anonymous open pit gold mine and proposes cost-effective drill and blast geometric parameters. The investigation focused on one operational pit with provided design parameters for two shots, shot 1 and shot 2. Existing blast parameters and two additional proposed sets of geometric parameters were evaluated using the Kuz-Ram and Chung and Katsabanis fragmentation models to estimate mean fragment sizes. The results indicated that the proposed blast parameters produced estimated mean fragment sizes within the mine’s desired range (not exceeding 45 cm). Additionally, the explosive energy was utilized efficiently per in-situ material blasted. The proposed parameters increased the estimated total volume of in-situ material fragmented by approximately 14% for both Shot 1 and Shot 2 compared to the current parameters. Furthermore, adopting the proposed blast parameters could lead to significant cost savings. The evaluated total drill and blast cost savings were approximately 11% for Shot 1 and 12% for Shot 2. These savings stem from the increased efficiency and effectiveness of the blast operations, highlighting the potential for substantial economic benefits. This study demonstrates that optimizing blast geometric parameters will allow open-pit mines to achieve desired fragmentation, utilize explosive energy more effectively, and realize considerable cost savings in drill and blast operations.

Jan 21, 2025

By Robert Hopler

Although electrical instruments were being widely introduced into the study of seismic tremors, attempts to understand and quantify shocks from blasting continued to use rather primitive methods well into the 19th century.

Jan 1, 2007

By James T. Ludwiczak

Drilling and blasting in a Karst (sinkholes and mud seams) environment has long been a problem for blasters, miners, quarry operators, contractors, and developers. While one cannot change the geological conditions, one can take some measures during the bidding process and the initial preparation of the blasting program to help reduce some of the problems. During the geotechnical investigation and developing the test/core drilling grid, the owner/developer needs to take some additional measures that will provide important data to the blaster to help reduce the problems associated with blasting this type of geology. The owner/developer must also understand that, due to the geologic conditions, the results of the blasting will not be ideal and there may be additional blast-related costs. If provided the proper geologic data, the blaster can develop drilling patterns and blast designs that will help reduce some of the more problematic areas.

Jan 1, 2005

By Paul McAnuff, Alastair Grogan

In Canada, the only vibration regulations which apply across the entire country are intended to protect fish spawning areas. The Provinces and Territories regulate mines and quarries, and are responsible for setting vibration and airblast regulations. Some Provinces have set specific regulations, while others leave these restrictions to the mines inspectors who can set limits on a case by case basis. For the most part, it is left to individual municipalities to regulate blast vibrations and airblast from other blasting activities, which differ from jurisdiction to jurisdiction, and in some cases are not enforced. Blasters working in different jurisdictions have to be aware of the applicable regulations for the area they are working.

Jan 1, 2005

By Sandra Penttinen

There are several ways to get a positive reaction from abutters to blasting projects. When you need to enter structures to conduct a blast-blast inspection, the impression you make on the structure owner must be positive from the very start. Your public relations with neighbors is the key. The purpose of all communications with persons residing near planned blasting operations is to educate structure owners as to what will take place during the blasting operations, to explain that safe blasting practices will be followed and vibration and airblast limits will be imposed to protect surrounding structures from damage. Once access into structure is obtained, the structure owner can be shown, by careful documentation, all existing cracks and defects in the structure prior to blasting and construction. The objective of your visit and all communications is get your foot into the door and win the confidence of the structure owner so that he or she understands blasting will not compromise the structure.

Jan 1, 2005

By Nikolaos Petropoulos, Ulf Nyberg, Daniel Johansson

A series of signature boreholes were blasted to observe any difference between confined and free face blasts. Four geophones were used to capture the compressive wave. The conventional approach, i.e. the calculation of vectorized peak particle velocity (vPPV) did not show any difference. Also a wavelet transform was tested.

Feb 1, 2020

By Y Nagendra, A. Ravi Kumar

A breakwater is a construction for protecting the marine structures like port, harbor, or anchorage-basin and berthed marine vessels from the destructive influence of the sea waves. The breakwater is constructed by using geologically competent, heavy, massive rock like granite, basalt etc having physical and mechanical properties within the limits specified by the designers. The construction requires boulders in varying sizes ranging from 0.5 kg to 20,000 kg. The stones from 0.5 to 1000 kg are called as core fill and boulders greater than 1000 kg are termed as armor blocks. These armor blocks cover and protect the core fill and prevent it from escaping. The requirement of armor blocks ranges between 25 to 35 %. The rest is core fill. However, the actual requirement depends on the breakwater design. In this context, the task of the mining engineer is to economically produce armor blocks and core from the designated quarry in right proportion with minimal losses. The whole bunch of engineering ingenuities should be put forth for obtaining the required armor blocks. The armor block production from any blast depends chiefly on geological conditions, bench dimensions and blast design. This paper is an attempt to bring out the various parameters affecting the performance of the blasting for armor block production using a case study.

Jan 1, 2005

Explosive manufacture, handling and transportation is hazardous and special precautions should be taken while manufacture, handling and transportation. Various regulations and rules defined in explosive act and factories act of India are discussed in this communication. General process control measures during the manufacturing of different types of explosives are also dealt in detail. Various processes hazardous in manufacture of various explosives like slurry explosives, PETN, detonators, styphnic acid, lead azide and lead styphnate and special precautions to be taken during the manufacture of the above explosives are also discussed.

Jan 1, 2007

By W B. Gregg

"A review, update, and expansion of Thiokol’s presentation at BAl’s Fiih High Tech Seminar titled ‘ADetonator - An Era of Precision in All-Electronic Detonators” is provided herein (and should be considered as a supplement to that publication). Thiokol is currently in the development and field evaluation phase of activities for our ACCUBLASTTM all-electronic detonator. The ACCUBLASTTM detonator uses a semiconductor bridge (an electronic match) in place of a conventional hot wire to initiate a safer, less sensitive material, titanium subhydride potassium perchlorate. The device is programmable to provide blast delays in one millisecond increments ranging from 1 to 500 milliseconds. The ACCUBLASTTM detonator combines an all-electronic programmable timer coupled with a semiconductor bridge to ensure detonation timing accuracy with +I00 microsecond precision. Initial development and field testing have been completed. These tests have verified ACCUBLASTTM detonators’ precision."

Jan 1, 1995

By Lynn Long

We have seen many new developments in the explosive and blasting accessory category, but one of the most useful items is the blast control plug. Blast control plugs are cone shaped units that are placed in the stemming just above the explosive load. They are placed about 8 to 12 inches up into the stemming material.

Jan 1, 1996