Search Documents

"Standing 92 stories high and just over 1,362 ft tall, Chicago’s Trump International Hotel and Tower is perfectly positioned at the center of one of the world’s most impressive skylines.The Tower serves as a link between its famous predecessors, Willis Tower (formerly, the Sears Tower) to the south and the John Hancock Building to the north. Originally planned to be the world’s tallest building, the project was scaled back when the developers started questioning the need for super-tall buildings after the September 11, 2001 terrorist attacks. In its River North neighborhood, Trump Tower dominates the skyline as a symbol of Chicago’s last great building boom, standing triumphantly over other high-profile projects that have been postponed due to current economic realities.It is often said that the three most important factors in real estate are location, location and location. This maxim was not forgotten by The Trump Organization when the site was selected for the International Hotel and Tower. Located two blocks west of Michigan Avenue and Chicago’s famed Magnificent Mile, the site is bound by the historic Wrigley Building to the east, Wabash Avenue to the north and west, and the Chicago River to the south. The building’s position along a bend in the Chicago River allows visitors and residents unobstructed views to the mouth of the Chicago River and Lake Michigan. Site ChallengesUnderneath the site there are approximately 10 to 20 ft of sand and urban fill underlain by soft Chicago blue clay. At 75 ft in depth, the soft clay transitions into Chicago hardpan, a very hard till that was consolidated by the glaciers over 10,000 years ago. Below the hardpan, the till turns granular with cobbles, boulders and water under pressure. Bedrock is about 100 ft below existing grade and has a weathered surface with fractures and clay seams. Unweathered limestone bedrock is sound and hard with unconfined compressive strengths of 10,000 to 20,000 psi."

Jan 1, 2009

By Guo Qian, Du Guangyin, Deng Yongfeng, Liu Songyu, Wang Ningping

"Metakaolin (MK) can efficiently enhance the strength and the impermeability of concretes and mortars. However, it has rarely been attempted in admixtures of cement-stabilized soils until presently. As deep mixing method is wildly used in ground improvement, the strength of cemented soils (soilcrete) and the applicability of the MK should be considered. This paper focuses on the macro-strength development of cement-stabilised silty soil mixed with MK. The result shows that the addition of MK can enhance the unconfined compressive strength of the soilcrete, which attributes to a combination of the rates of OPC hydration and the MK-CH reaction. Note that the strength of soilcrete was influenced by the properties of soil, water-to-binder mass ratio (W/B) in admixtures, which needs to be reconsidered since the binder mass composes that of cement and MK totally.INTRODUCTIONCement was used in ground modification techniques, such as the jet grouting, deep mixing method (DMM) which was put into practices in Japan and Nordic countries in the middle of the 1970s, and then spread to China, South East Asia[1]. For last decades, fly ash, slag or silica fume was mixed with cement to form the new cement base stabilizing agent in the view of economy and performance improvement. The mechanical behavior of these soil-binder admixtures (nominated as “soilcrete”), was investigated. But the soilcrete modified with the metakaolin (MK) was still not investigated much and lots of further work needs to be conducted.Some laboratory experiments of the soilcretes modified with MK have been taken[2~4]. Kolovos et al. (2013) indicates that the unconfined compressive strength has a more significant improvement when W/B equals 0.4 than that when W/B equals 1.20 concerning the water-to-binder mass ratio (W/B). Sonebi et al. (2013) investigates the mechanical behaviors of cement grouting containing MK with W/B equals 0.4, and also found the effectiveness of the addition of MK. Zhang et al. (2014) performed the studies on Lianyungang marine clay improvement showed that MK obviously enhanced the quality of cemented soils.In this paper, the strength of soilcrete modified with MK is further investigated, where the unconfined compressive strength at different curing time, the content of MK and cement (w/w) in lab conditions was discussed."

Jan 1, 2015

By Seth Robertson, Daniel Belardo, Travis Coleman

Thermal Integrity Profiling (TIP) is a non-destructive method used to evaluate drilled deep foundation integrity. This integrity testing method is specified more frequently, and is becoming an industry standard in the transportation and private construction sectors. This testing method utilizes heat generated during the concrete/grout curing process to assess deep foundation integrity over the evaluated length. With compilation of the measured temperature versus time and installation records, a model of the Effective Average Radius versus measurement depth is generated. The generated effective shaft model is highly dependent on specific construction details, subjective modeling parameters, and proper interpretation of concrete/soil heat dissipation characteristics. Key components of the TIP analysis include both qualitative and quantitative assessments. Qualitatively, variations or sharp reductions in temperature profiles may indicate potential anomalous regions. Quantitatively, a correlation is established between measured temperatures and estimated Effective Radii for subsequent integrity evaluation. Best practices in processing the TIP measurements are presented, including selecting the optimal time for analysis, normalizing the thermal profile, and proper interpretation of potential anomalous regions. Recommendations for implementing mitigation efforts and interpretation of the TIP results are presented.

Sep 8, 2021

By Nozomu Kotake, Rakshya Shrestha, Ralph Griffin, Stefanos Papadopulos, Jeff Fippin, Sushil Kafle

Direct Power Compaction (DPC) is a deep Vibro-compaction method used for liquefaction mitigation. In DPC, H-beams are used as vibrating rods penetrating deep into the ground, and a vibrating force is applied directly to the tip of these H-beams to densify the loose ground. A characteristic feature of DPC is the use of a flapping plate installed at the base of the H-beam to enhance the compaction efficiency during penetration. In addition, 2-rod and 4-rod type equipment have been developed to improve productivity and enable rapid construction. DPC was selected as the most suitable and cost-effective technique to mitigate liquefaction hazards in two projects in the San Francisco Bay Area, one on Alameda Island and another on Treasure Island. Both sites were capped with hydraulically placed sand fills. Liquefaction analyses indicated excessive liquefaction-induced settlements and large lateral spread without ground improvement. Densification using DPC was performed up to depths of 42 ft to reduce the liquefaction potential of the sand fill to acceptable levels and to allow planned improvements. Cone penetration tests were conducted before and after DPC to evaluate its performance. This paper describes the equipment and process involved in DPC and discusses its application in terms of subsurface conditions and geotechnical design considerations.

Sep 8, 2021

By Johannes Labenski, Christian Moormann, Johannes Aschrafi

"Open steel pipe piles are used for various applications in costal engineering, port structures and increasingly important for offshore structures. During the installation of open steel pipe piles the formation of a plug has an influence on the installation process of the pile and also on the final bearing capacity. The formation of the plug depends on different factors, e.g. the pile diameter and the installation method. This paper starts with a structured overview about analytical methods (API, EAP-EAU, UWA-05, HKU-12, Modified API) to calculate the axial bearing capacity of open steel pipe piles. The numerical simulation of the installation process of open steel pipe piles has to fulfill high demands, i.e. to accurately represent the penetration of the pile inside the soil, the formation of the plug and also the stresses and strains during the installation. A numerical back analysis of a comprehensive field test, using the Coupled Eulerian-Lagrangian (CEL) method and a hypoplastic constitutive model for sand, reveals the stresses and displacements of the soil and of the piles. The analysis provides a comprehensive understanding of soilpile interaction.INTRODRUCTIONThe particular difficulty in the numerical simulation of plug formation, is that the effect of plugging inside open ended steel pipe piles has not been fully investigated. In scientific papers different approaches are documented to explain this phenomenon. Some are based on in-situ tests and others are based on numerical simulations. One of the challenges is to determine the end bearing capacity and shaft friction of the steel pipe pile. Different approaches have been developed over the years to determine them e.g. from Randolph et. al. (1991, 1994) and Paik et. al. (2003). Recent approaches are the ICP-05 Method (Jardine 2005), the UWA-05 Method (Lehane 2005) and the HKU-12 Method (Yu & Yang 2012a). A comparison of some methods can be found in Schneider et al. (2010). A plug inside an open steel pipe pile can be visualized as a spatial bracing of soil between the inner surfaces of the pile, cf. Lüking (2010).. However according to Lüking & Kempfert (2012) this bracing only exists for the height in the end of the pile equal to twice its diameter.To identify a plug inside a pile, there are different measurable parameters. One parameter is the development of stresses around the pile during and after its installation. Henke (2013) measured the inand outside horizontal stresses at the pile tip during the installation. The results showed higher stresses on the inside compared to the outside. To validate his measurements he performed a numerical back-analysis of the measured installation process and got matching results."

Jan 1, 2017

By Chu E. Ho, Alfredas Daugiala, Nicola Ebanks

"The construction of an ancillary structure for the new Second Avenue Subway Line in Manhattan, New York City involved a deep excavation in highly variable rock conditions adjacent to a fragile masonry building. The maximum difference between the lowest and highest rock elevations was about 30 feet, which posed a problem for the installation of secant piles that formed the supporting retaining wall for the excavation. At certain areas, the rock levels were higher than the top of the invert slab of the ancillary structure. To avoid disturbance to the adjacent fragile building, the secant piles were fully cased for drilling through the overburden soils and the rock sockets were formed using non-vibratory technique. This paper discusses the design and installation details of the secant pile wall and the contingency measures that were considered to mitigate the highly variable rock conditions. Monitoring of the adjacent fragile building showed that impact of pile installation were controlled within tolerable limits and safety of the building was not compromised.INTRODUCTIONThe 96th Street Station forms part of the newly constructed Second Avenue Subway Line on the East side of Manhattan Island, New York City (Figure 1). During construction of this station, several deep excavations were carried out adjacent to existing fragile buildings (Arksman et al. 2012, Grigson et al. 2016). These fragile buildings were typically four to five stories high, with a single rubble wall basement supported on timber piles or seated directly on the fill. The timber piles were often found to be in a poor condition and connections to the footings were compromised due to rotting of the timber within the zone of water table fluctuation. Several of these fragile buildings had to be strengthened and underpinned to improve the stability of the structures prior to commencement of excavation for the new subway station box (Trabold et al. 2012, Ho and Pena-Iguaran, 2013). The situation was most challenging at Ancillary Buildings 1 and 2 located at 93rd and 97th Street respectively, where secant pile walls were located merely 2 feet away from the adjacent property line, due to architectural space constraints. While mitigation of excavation induced ground movements can be controlled by the adoption of a stiff excavation support system, a more concerning factor was the uncertainty associated with the impact of the secant pile wall installation on the stability of the existing fragile buildings. This was particularly difficult at Ancillary 1 where the secant piles encountered highly variable rock levels that intruded into the excavation space. The following sections discuss the design and installation of the secant pile wall and contingency measures that were considered at Ancillary 1."

Jan 1, 2016

By Patrick Granitzki, Alicia Plinio, Janitha Batagoda, Peter Howell

The City of Newark is making a comeback with new mixed-use multi-storied Residential Development projects. The majority of developers tend to use driven H-pile deep foundation systems to support their super-structures. A different approach was recommended for one particular new development near the Passaic River. The surficial geology included glacial deposits consisting of loose to dense sand overlaying relatively soft silt and clay and a lower stratum of medium-dense sand. During a preliminary site investigation for the project, bedrock was encountered at depths ranging between approximately 168 feet to 182 feet below the ground surface. Design capacity required a single pile of 200 tons. Two different pile foundation systems were evaluated in conjunction to the typical driven H-pile system in order to review potential costs and construction schedule impacts. The two alternative pile systems evaluated were tapered tube piles and drilled displacement piles. Theoretical calculations were followed by in-situ load testing. The field testing results indicated the use of drilled displacement piles as the best option for a portion of the proposed building. This paper discusses the different piles systems considered, installation and using drilled displacement piles to minimize cost and optimize construction.

Sep 8, 2021

By Babak Mamaqani, Pirooz Barar

Regional Connector Transit Corridor (RCC) is part of the Los Angeles metro expansion project under construction which adds three new stations into the system. PB&A was responsible for the design of the support of excavation (SOE) systems for two stations, 2nd/Broadway and 2nd/Hope, in RCC. In this paper, challenges and lesson learned from SOE design of 2nd/Broadway station with a main focus on underpinning design are discussed. 2nd/Broadway station required to cut and cover excavation of 500 ft long by almost 100 ft deep, underneath 2nd Street. SOE systems consisting of drilled soldier beams with tiebacks and/or struts. The main challenge in 2nd/Broadway station was to underpin the LA Times building which was partially protruded into the station. A chellenging underpinning system consisted of concrete panels and ground anchors was designed to support the building surcharge and prevent settlement. The underpinning system was designed based on METRO design criteria and the deflection was evaluated by Finite Element Analysis (FEA) program, PLAXIS 2D. A maximum deflection of 0.4 inches was calculated to occur at the top of the underpinning system. Data from settlement and tilt sensors showed minimal movements which aligned with PLAXIS outputs. PROJECT DESCRIPTION The Regional Connector Transit Corridor (RCC) is Los Angeles Metro’s ambitious Light Rail Project. It runs under the City’s main thoroughfares, Flower and 2nd Streets, and when complete will alleviate traffic and parking congestion in downtown Los Angeles. The Regional Connector will connect thousands of residents living in the bedroom communities of the Inland Empire and Long Beach to their jobs Downtown. The rail line will serve 1.9 miles, using the $1.756 Billion budget to construct the underground rail line, including 3 new stations, at 2nd & Hope Street, 2nd & Broadway, and 1st St. & Central Ave (Fig. 1).

Jan 1, 2019

By R. Lee Wooten, David R. Shields, Darren D. Clark

"Borehole permeability tests that measure flow or head changes in boreholes located within seepage barrier walls are commonly used to estimate the in situ permeabilities of those walls for quality control and assurance. The current state of practice for estimating permeabilities from these barrier wall borehole tests is to use equations published by M. J. Hvorslev in 1951. Hvorslev’s borehole test equations model an infinite stratum of uniform permeability, which is not the actual condition for a test performed in a low permeability barrier wall located within a high permeability stratum. We examine and develop alternative equations based on line source analytical models, which more closely match barrier wall test conditions. We describe how these alternate equations can be used to estimate barrier wall permeabilities from borehole tests and compare the results to those obtained from the Hvorslev models. We also provide recommendations that consider differing upstream and downstream water levels.Barrier Wall Permeability Tests - State Of PracticeThe installation of seepage barrier walls has become more common in a variety of applications ranging from dams and levees to contaminated sites requiring retardation of groundwater flow. The types of seepage barrier walls and installation methods include soil-bentonite, soil-cement-bentonite, concrete, self-hardening slurry, geomembranes, and sheet piles, installed with various soil mixing, slurry-supported trench, and driving methods.Owners and contractors have used a variety of methods to evaluate the permeability of these seepage barriers. The following table lists commonly used quality control/assurance tests for evaluating the permeability of a seepage barrier."

Jan 1, 2016

By Hamed Layssi, Farid Moradi, Thomas Tingson

This paper describes the feasibility and pilot study of of using existing non-destructive testing solutions for evaluating structural integrity and mechanical performance of mass concrete foundations. This paper includes two pilot studies using well-known NDT methods (i.e., Crosshole Sonic Logging and seismic tomography) for new applications (i.e., NDT inspection of mass concrete foundations). In the first case, we will examine an existing mass concrete foundation block with internal cracking, which has negatively impacted the strength and stiffness of the foundation block. A combination of pulse velocity and 2D tomography was used to evaluate the structural integrity in the foundation block. In the second case, the quality and integrity of newly built mass foundations were evaluated using Crosshole Sonic Logging (CSL). The methods are combined to locate potential sub-surface defects such as large voids and discontinuities. This paper aims to study the effectiveness of the NDT methods of Deep Foundations to assess the quality and structural integrity of new and existing mass foundations and explore the opportunity to extend the capabilities of these tests beyond their conventional use.

Sep 8, 2021

By Jeffrey M. Taylor, Arturo Ressi di Cervia

"Construction of the drilled shafts for the Brightman Street Bridge Replacement Project were not only challenging due to working over the water but were also challenged by changed soil conditions, concurrent work being performed by an adjacent contractor on the same project, environmental restrictions and severe winter conditions. A total of 36 x 8 foot (2.44m) diameter drilled shafts with 7.5 foot (2.31m) rock sockets were installed for the East and West bascule piers. This project also included Osterberg Cell load testing on two production drilled shafts at both the East and West bascule piers. The results from the load test program were used to fine tune the design of the drilled shaft rock sockets. From a constructability standpoint the reverse circulation drilling method with a pile top drill rig proved to be an excellent choice for drilling the overburden and rock sockets of the large diameter deep drilled shafts. INTRODUCTIONThe replacement Brightman Street Bridge spans the Taunton River between Fall River and Somerset in Massachusetts.The new crossing is located approximately 1500 feet (450m) upstream from the existing Brightman Street Bridge, which was built in 1908. The new mainline bridge includes nine spans totaling 1725 feet (525m). A bascule type moveable span will be located in the middle of the Taunton River and provide a 200 foot (61m) open channel centered about the 400 foot (122m) navigational channel. The bascule span, which has a span length of 409 feet (124.7m), will be a trunnion-type four leaf structure with a solid deck. A site plan is shown in Figure 1 Contract 3, which includes construction of the foundations for the East and West bascule piers, was bid on December 19, 2000 and was awarded to Modern Continental Construction Company (MCC) on January 24, 2001. MCC in turn awarded the subcontract for the installation of the drilled shafts to TREVIICOS Corporation, which started mobilizing in June of 2001.The scope of work for the drilled shafts of Contract 3 consisted in installing 18 drilled shafts in three rows on each side of the river to support the bascule piers located in the middle of the Taunton River.The foundation plan for the bascule span is shown in Figure 2."

Jan 1, 2004

By Dipl. -Ing. (FH) Thomas Schmitt, Dr. Melvin England

Foundations in Geneva are difficult and expensive due a large overlayer of clay and silt above competent bearing material in the moraine. Common foundation schemes use deep barrettes or bored piles, first passing large, weak layers of soil before finally reaching acceptable, solid moraine with reasonable values of skin friction and end bearing resistance, thus requiring further deep penetration for the necessary length for load transfer in the moraine. Depths of more than 60 m (200 ft) in Geneva are common in this region. At the Onyx-Project Geneva Implenia Foundation Company also encountered these circumstances. Despite usual solutions Implenia referred to an old and well known, but still intelligent and in today’s words smart, efficient and economical solution. Using small shafts, passing the large layers of clay and silt, ending with the pile toe in the underlaying moraine with a belled or underreamed base was the technic adopted to save drilling time, reduce spoil and concrete, so finally reducing the CO2 footprint. Piles with enlarged base (“belled” or “underreamed”) are reported at the beginning of the 20th century, for example at Chicago, which has a quite similar geotechnical structure as Geneva with the need of deep foundations. The first pile base enlargements were built in hand-dug caissons with wood lagging and steel ring bracing. In the 50s and 60s piling works were more and more mechanized, driven by the development of more powerful cranes and specialized drill rigs. Additionally the first tools for mechanized base enlargement were invented around that period. This report describes the project situation at Geneva, the drilling and enlargement technique of the pile base, the verification of the design values with an in-situ bi-directional load test and the smart execution by reduction of CO2 and costs.

May 1, 2022

By Bosco Poon, Kim Chan, Luis Raúl Castañeda, Geoff McKay

"Driven steel tubular piles of up to 2 m diameter have been used to support abutments and piers of a bridge over Nambucca River and floodplain. The bridge was designed by Arup-Aurecon Design Joint Venture (Lead Designers) with GHD leading the geotechnical design assessment in conjunction with Acciona Ferrovial Joint Venture (AFJV – Principal Contractor). Piles were to be driven through alluvium and founded on foliated Phyllite bedrock. The large diameter piles posed significant challenges on bearing capacity assessment and pile acceptance criteria, especially for anisotropic rock strength. Prior to pile driving, boreholes were drilled at each pile location, accompanied with a suite of rock index and UCS testing. AFJV and GHD oversaw geotechnical construction verification. All production piles were monitored with a Pile-Driving-Analyser to manage driving stresses and pile termination. Wave matching CAPWAP analyses were performed on 40% of the piles at the end-ofdrive, or restrike, to satisfy specification requirements and limit over-driving. This paper presents discussions on the design and construction of the driven piles with findings from the extensive dynamic pile data obtained. Based on the shaft resistance distribution and toe resistance obtained from CAPWAP analysis, the mobilised pile shaft frictions fs of the soil / rock materials, as well as the end bearing fb of the founding Phyllite bedrock, are examined. The impact of the rock fabric foliation angle on the m obilised fb, and the relationship between rock strength and the mobilised fs are outlined.INTRODUCTIONThe Bridge over Nambucca River consists of a single bridge structure, comprising single substructures and separate superstructures. The 850 m long bridge facilitates the crossing of the Northbound and Southbound carriageways of the Pacific Highway Upgrade over Nambucca River, with central median barriers, separated by a horizontal clearance of 50 mm. The bridge is required to span over the Nambucca River, which is a navigational channel, and over the adjacent floodplains, including two local access roads and the existing Pacific Highway. The bridge superstructure consists of 21 simply supported spans, each comprises four 2.25 m deep precast post-tensioned U-Girders, with two girders across the width of each carriageway. The spans of girders vary from eleven spans of 39.5m and ten spans of 41.5 m. The floodplain section of the bridge was founded on up to 2m diameter steel tubular piles, designed to be driven through alluvial sediments and weak rock to nominal refusal on sound rock. Dynamic load testing using wave matching CAPWAP (CAse Pile Wave Analysis Program) analyses in conjunction with PDA (Pile Driving Analyser) were used to verify the pile integrity and mobilised capacity. This paper discusses geotechnical aspects associated with design and construction of driven piles. The methodology developed for construction to verify pile capacity and to meet acceptance criteria is outlined. Based on the shaft resistance distribution and toe resistance obtained from CAPWAP analysis, the mobilised pile shaft friction, fs of the soil / rock materials, as well as the end bearing, fb of the founding Phyllite bedrock, are examined. The impact of the rock fabric foliation angle on the mobilised fb, and the relationship between rock strength and the mobilised fs are outlined."

Jan 1, 1900

By Mark D. Fuhriman, Parham Khoshkbari, Robert Fosse

Drilled displacement piles are becoming an increasingly common deep foundation choice for their relatively simple installation methods, applicability to a wide range of subsurface conditions, and versatility. The installation method includes drilling and displacement of the soil followed by delivery of fluid cement grout under pressure, and placement of steel reinforcing to complete the pile. Because the installation method uses blind processes that do not permit direct observation of the pile, it is desirable to employ redundant testing tools to complement good construction techniques and inspection practices to ensure integrity of the piles. This paper examines the use of a range of integrity testing tools used for pile installations at a major office campus development. Because the integrity of a drilled displacement pile and its performance depend to a large extent on the skill and experience of the installation crew, the paper explores how use of multiple practical tools, including automated monitoring tools on the pile installation equipment, thermal integrity profiling, and high-strain dynamic testing, ensure structural integrity of the completed piles and how redundant integrity testing methods complement good construction and inspection practices add confidence in the quality of the foundation system.

Sep 8, 2021

By Aaron Evans, Chu E. Ho, Tom Richards

"This paper describes an innovative case history of using jet grouting to form a groundwater cutoff wall at the interface of a cut-and-cover construction and an existing tunnel. The design of the jet grouting layout was complicated by the presence of a left-in-place bulkhead of unknown dimensions abandoned by previous construction of the existing tunnel. Jet grouting was performed through predrilled holes within the narrow space between the existing bulkhead sheeting and tunnel structure. A systematic sequence of primary and secondary jet grout elements of varying diameters and panel lengths was executed to achieve an effective groundwater barrier. A key challenge in the jet grout design was the impact of potential deviations due to shadowing effects of the left-in-place bulkhead sheeting and pre-formed jet grout columns, as well as overbreak concrete in adjacent secant pile walls. The flexibility of the jet grouting methodology enabled a wide range of operational parameter combinations to be performed, allowing column diameters to be adjusted based on actual field installation measurements. Special precaution was exercised when grouting at critical locations to avoid over-pressurization and damage to the existing tunnel structure.IntroductionThe 96th Street Station box for the new Second Avenue Subway Line in Manhattan, New York included a transition tunnel, which connected the station to an existing tunnel built in the early 1970s (Figure 1). The new station and transition tunnel were both constructed using the cut-and-cover technique with bottom-up sequence (Aksman et al. 2012, Grigson et al. 2016). The main station structure incorporated permanent diaphragm walls for most of its length, except for the southern segment where high rock levels were encountered and the station box was constructed within temporary secant pile walls socketed into the rock. The permanent diaphragm walls were also utilized for temporary excavation support (Ho and Hu 2014). At the northern end of the site, the new transition tunnel was constructed within temporary secant pile walls that extended from the station diaphragm walls to the existing tunnel at the tie-in location. A temporary traffic deck spanning 60ft across the secant pile and diaphragm walls along the full excavated length of the site allowed traffic to continue operating at street level while construction of the station and transition tunnel progressed below grade."

Jan 1, 2016

By Srijit Bandyopadhyay, Aniruddha Sengupta, G. R. Reddy, Raj Banerjee

The objective of the present endeavor is to compare the performance of a pile raft system in foundation sand subjected to lateral loads. To study the behavior of pile raft system in sand a laboratory test was conducted on small scale model foundation system. The raft and pile was modeled by square concrete foundation of 250 mm x 250 mm x 15 mm in length, breadth and thickness and 25mm diameter and 250mm long circular pile located at the center of the raft. The system was tested under static lateral loads of 6.25N, 12.5N, 18.75N and 25 N respectively resting on dry Kasai River sand. A vertical surcharge pressure of 1.5kPa (10 kg) was applied on top of the model raft for each case. The results of the model tests have been simulated by a general purpose 3-D finite element software and the model has been validated with experimental results. The moments of the pile obtained from the model tests and those predicted by the numerical analyses for all the lateral loads matches reasonably well. For matching the trend of bending moments obtained from experiments, validation with theoretical results have been done with the help of Matlock and Reese (1960) approach for a single value of lateral loading. Moreover, a parametric study has been conducted with 5mX5mX0.3m raft size with 0.5m diameter and 5 meter long pile with increasing number of piles namely 2, 5 and 9 respectively to study the response in terms of moment and lateral deformation under available earthquake loadings, like Loma Prieta (1989) and Darfield Christchurch (2010). Bending moments of piles and load deformation curves for lateral loading have been studied for each case in which it is observed that the bending moments of pile significantly reduces (around 4 times) as the number of pile is increased to two, but it decreases to a nearly constant value (it saturates) as the number of pile is increased to five and nine. Moreover, the lateral deformation of piled raft system drastically reduces (around 2.4 times) for two pile system, and it saturates to a constant value with five and nine pile system. All these results indicate the constancy of stiffness irrespective of the number of piles in the piled raft.

Jan 1, 2015

By David W. Martel, Tom George

"As part of the regional water authority review and upgrade of local dams a 35m x 5m x 3m wet soil mixed block was required for stabilisation of a dam wall toe in remote Victoria, Australia. Remote access, extremely poor roads and high mobilisation costs made more traditional CSM and deep mixing methods cost prohibitive. The dam required a redesign to raise the wall by 2.0m to increase water storage. Additionally, the dam required additional stabilisation to reduce the risk of liquefaction during an earthquake event. Soil testing indicated loose, cohesionless, high permeability soils to a depth of 3.0 to 3.5m across the toe of the wall. This resulted in high dam seepage through the toe of dam wall potentially causing the factor of safety during a seismic event to decrease to a dangerous level. A number of laboratory trials were completed to determine the mix ratio of cement required to improve the strength of the saturated, liquefiable soil.Wagstaff Piling was responsible for achieving the required soil/cement strength and mix depth on site. As the ground conditions were too soft for conventional soil mixing equipment, an excavator mounted Mitsui road header was modified to fit a 20 tonne excavator. A purpose built remote batching plant was set up on more stable ground approximately 200m from the wall and utilised for preparation of cement and water slurry for supply to the machine. As the ground was too soft to support the excavator, the progressively improved ground was used as the working platform. Both wet grab sampling and in situ testing was undertaken to determine the UCS of the improved soil. These results indicated several variations in the results due to size effects.1 INTRODUCTIONA small town in remote Victoria relies totally on its water supply from a small dam. The dam wall required stabilisation works by ground improvement as studies completed on the dam classified it as a high risk of failure under an earthquake event. In addition, the earth fill dam had high levels of seepage and poor control measures, requiring the dam to be upgraded to comply with all regulations.The relevant water authority engaged a contractor under a design and construct contract to complete the works. Wagstaff Piling was engaged as the Subcontractor to provide design and construction advice including the contract for the ground improvement works. Initial discussions involved CSM walls, cut-off walls and mass soil mixing solutions. However, due to the access restrictions for piling equipment, mass soiling mixing was the chosen method of ground improvement."

Jan 1, 2015

By Aditya Ayithi, William G. Ryan, Dean Herbst

"For rock socketed drilled shafts, it is a common practice not to include the frictional resistance of overburden soils into the nominal capacity estimation. The primary reason often being cited is “overburden soils resistance is negligible compared to that of rock socket resistance.” However, in certain geological conditions, where the rock layer is located at greater depths, friction resistance from overburden layers can be significant. In addition, at such great depths, shaft drilling becomes very complicated and expensive. In these situations, considering the resistance of the overburden layers can be an economic alternative.This paper presents a case study of an Osterberg cell (O-cell) load test conducted on a 161.8 feet long and 78-inch diameter instrumented test shaft. Based on initial designs, a 72-inch diameter rock socket of lengths 23 and 26 feet was required to provide a LRFD factored friction resistance of 3,200 kips. The load test results revealed that the material in the 72-inch diameter socket does not represent a true rock. However, the test results also proved that the factored friction resistance of overburden layers is greater than the required design resistance. Based on the load test results, it was decided to allow the overburden soils frictional resistance to be considered in the shaft design, resulting in significant economic savings.INTRODUCTIONRock socketed drill shaft design guidelines of various State Department of Transportation (DOTs) agencies allow friction and/or end bearing resistance of only the rock socket portion into the design capacity estimation. It is typical to neglect the frictional resistance of overburden soils. However, in certain geological conditions where the rock layer is at greater depths, friction resistance of the overburden soils can be significant. In this case the friction resistance of overburden soils was verified via the specified instrumented O-cell test program and then used as part of the design capacity.PROJECT DESCRIPTIONAs part of I-29 improvement project, Iowa Department of Transportation (Iowa DOT) planned to replace the dual four lane bridges that cross the Floyd River in Sioux City, Iowa with dual six lane bridges (Fig. 1). Expected benefits from this improvement include improved safety, traffic operations and roadway infrastructure conditions.BRIDGE SUBSTRUCTUREThe project consists of two individual bridges; a new south bound bridge and a new north bound bridge. The south bound bridge is 646-ft long and the north bound bridge is 644-ft long. Both are six-span, pretensioned and pre-stressed concrete beam bridges of varying width. Bridge foundations were designed such that the abutments of both bridges will be supported on driven steel piles and the bridge piers will be on drilled shaft foundations."

Jan 1, 2016

By Thomas Hyatt, Brandon Phetteplace, Camilo Alvarez

A test pile program was undertaken at a project site in Ain Sukhna, Egypt for an import/export oil jetty. Two 1219 mm diameter open ended steel pipe piles were evaluated at two separate test locations. Each test pile was dynamically tested during initial drive utilizing a Pile Driving Analyzer (PDA). Restrike testing was also performed to evaluate the time dependent soil setup. One static compression test and one static tension test was performed at each test location. A correlation of the static and dynamic load test results was established to develop a driving criteria for the piling across the two kilometer project. The constructability benefits of shorter piles will be discussed in more detail, given that the pile lengths were shortened by 9 to 10 meters on average. Lastly, the use of a four pile linear layout to perform both compression and tension tests will be covered. INTRODUCTION With the increased number of Very Large Crude Carriers (VLCC) & Ultra Large Crude Carriers (ULCC) being used to transport oil products around the world, companies and/or nations are presented with the challenge of transferring these products to and from the carriers in deep water scenarios, typically 15 to 20 meter depths, to accommodate the vessels draft. One option for loading/unloading the oil products from a VLCC or ULCC would be to transfer to/from smaller vessels several miles offshore, whereas the most economical option is to unload directly to a pipeline via a berth/jetty platform near shore. These berth platforms must be designed to withstand multiple loading scenarios while these carriers are moored and transferring their products. The use of Large Diameter Open Ended Pipes (LDOEP) piles are a common foundation choice for this offshore application. One of the drawbacks of LDOEP piles, especially across a large project site, is that there can be extreme variability in the pile driving behavior. This can be caused by either a change in soil conditions or the performance of the soil plug. Due to this variability, it is important to verify throughout the duration of the project that the piling is being installed to the correct criteria as established during the load test program. A well designed driven pile load test program, preferably with the combination of Static Load Testing (SLT) and Pile Driving Analysis (PDA), should develop a driving criteria that can allow the contractor and owner to monitor any change in driving behavior.

Jan 1, 2019

By Musbah A. Hasan, Ahmed M. Nasr, Fauzi Jarushi

Many transmission towers, high-rise buildings and bridges are supported by piles. These structures may be subjected to large lateral loads. Therefore, experimental investigations on model piles under lateral loads were conducted in uniform dry sand. Small-scale model tests were carried out considering the influence of pile length, pile diameter, sand density, roughness of pile surface and vertical load on the lateral resistance of a pile. Furthermore, the effect of pile load eccentricity (e/L) on the ultimate lateral resistance was studied. Investigations, of the influence of various parameters on the magnitude of the coefficient of subgrade reaction (nh), were also performed. It was found that the lateral load capacity of piles increases with increase in pile length, pile diameter, pile surface roughness and increase in the sand density. The results also showed that the coefficient of horizontal modulus of subgrade reaction, (nh), decreases with deflection increase. From the results, the coefficient of subgrade reaction for a smooth pile embedded in medium dense sand would decrease by (134%) when the lateral pile head deflection (yg) changes from (2% to 5%) of pile diameter.

Jan 1, 2017