Search Documents

By Jogeshwar P. Singh, Aser I. Abbas, Mohamed Ashour

The presented methodology predicts the pile head response (i.e. pile head load - displacement curve) and develops the load transfer (t-z) curve of piles in sandy soils under tension forces based on soil/pile properties and soil-pile interaction. The proposed approach improves the prediction of the t-z curve in sandy soils compared to current practice. The method employs a nonlinear soil constitutive model to calculate the mobilized shear stress/strain in soil at the soil-pile interface induced by pile upward displacement. The approach accounts for the influence of the pile slenderness ratio on the predicted t-z curve and is validated through comparisons with measured pile head response and t-z curves from full-scale pile load tests. INTRODUCTION Piles may be subjected to axial uplift forces due to either static loading or cyclic loading. The majority of methods are only concerned with the pile ultimate tensile capacity. However, the mobilized pile stiffness (i.e., pile-head load-displacement relationship) is essential to determine the interaction between the foundation and the superstructure and consequently the performance of the whole structure. Methods that assess the pile ultimate tensile capacity usually assume the failure surface at the soil-pile interface and estimate the local side shear resistance using a lateral earth pressure approach. The Naval Facilities Engineering Command (NAVFAC 1986) and the US Army Corps of Engineers (USACE 1991) employed Eq. 1 to assess the ultimate shear stress (τ) developed at the soil-pile interface.

Jan 1, 2018

By Sastry Putcha, Vamshi Vemula, Aneesh Goly, Kumar Allady

Current dynamic testing practice to obtain pile total capacity will not yield optimum capacity due to the strain incompatibility between the side and tip resistances during driving. Superposition of end of initial drive- static tip capacity and the peak static skin capacity during beginning of restrike and adding them is the preferred method. The FDOT method determines independent pile static tip and skin capacities in real time analyzing appropriate blows from the embedded tip and top data of the Embedded Data Collectors (EDC). This data is collected through a wireless radio transmitter, receiver, and laptop software. The approach utilizes EDC tip and top data and nonlinear single degree of freedom system to satisfy force and energy equilibrium with a global genetic inversion analysis. Top impacted energy equals at pile tip as sum of Static, Damping and Inertial energy providing independent tip resistance. With EDC sensors as boundary conditions, pile is divided into desired segments and using global inversion techniques one dimensional equation is solved for independent skin friction for every blow. EDC data compared close static load test results. The EDC - FDOT method has enabled cost effective 100% testing of driven piles cost effective. INTRODUCTION Historical documentation has shown that not only driven piles have a long history of usage but also continues to advance unceasingly till today. Historians placed the first pile driving using timber piles in the 4th century BC. While modern pile driving systematically started around nineteenth century, the credit for conceiving the idea of the applicability of wave equation to driven piles goes to David Victor Isaccs of Australia. His 1931publication “Concrete Pile Driving Formulae” provides the basis for modern pile driving using stress wave theory. He felt that the dynamic formulae then in use lacked the capability of detecting integrity and hence developed stress wave theory. This work was further developed starting in 1938 by W.H. Glanville and colleagues of British Building Research Board as they developed the first solution to the wave equation. But these early efforts have really taken off only with the advent of computers. E.A.L. Smith (1960) published ‘Pile Driving Analysis with the Wave Equation’ and provided first numerical solution to the wave equation. Within few years, the FHWA funded research and in due course this effort ushered the era of externally instrumented pile driving.

Jan 1, 2018

By David R. Beadman

This paper discusses how modern techniques of design and construction were used to create the deep stations for the Copenhagen Metro. The deep stations are located in small squares within the city adjacent to many old and sensitive buildings. The architectural design provides a large open atrium to allow natural light to reach the column free platforms to give the citizens of Copenhagen a feeling of safety and security and encourage them to use the Metro. The design and construction contract was undertaken using the relatively new and untried Eurocodes. The resulting stations set new standards of design for underground metros and have pushed forward the frontiers of what is appropriate construction practice to protect the existing and enhance the future environment.

Jan 1, 2000

By J. Matos e Silva

"Abstract The paper refers five examples of executed diaphragm walls with one to five levels of anchorages. For each example a comparison is made between the results of the design using the traditional criteria and the ones obtained by using the Eurocode 7 and the Portuguese Norm related to the EC7 (NP EN 1997-1 2010), as the Eurocodes consider the possibility of each European country to adopt their own geotechnical parameters as these may vary from one country to another. A comparison is also made with the behaviour of these diaphragm walls during its construction phase; so the values from the design that were adopted in the construction are listed in tables 2 to 6 in the “Construction Options” columns. From the referred examples the author presents his conclusions.1 - INTRODUCTIONIn the so-called “traditional criteria” the soil parameters (dry unit weight, angle of internal friction and cohesion) have values obtained through tests or empirically. It is assumed that the characteristic values of the soil parameters adopted in Eurocode 7 are equal to the soil parameters adopted in the calculations by the “traditional criteria”. In the present paper the design according to the EC7 was made considering only the ultimate limit states and the respective Cases A1 and A2.The partial coefficients used for the actions in the present paper were those on Table 1:2 - CONSIDERED EXAMPLESThe five examples correspond to the situations of figures 1 to 5, and the respective results are summarized in tables 2 to 6.For all the considered examples, that are case histories, a simplified method published by Matos e Silva (March 2000) was adopted. This method attains good performances when compared with other more sophisticated ones as the finite elements and the elasto-plastic methods as described in a paper published by Matos e Silva (2000). All the obtained values were compared between them and with the so-called “Construction Options” that were the values adopted by the designers of the considered examples. For the wall bottom length calculation two possible situations were envisaged:"

Jan 1, 2014

By Gregory A. Stephan

A case history of design, prediction, probe pile driving, and construction of a pile foundation for Building 3 of Waterside at Bay Beach Condominiums located in Fort Myers Beach, southwest Florida, is presented. Site geometry constraints, the presence of a 12.0 ft (3.6 m) deep lake occupying the southern one-third portion of the proposed building footprint, and marginal subsoils provided specific challenges for design and construction of the foundation. The subsoil conditions were explored by performing Standard Penetration Test (SPT) borings and a Piezocone Penetration Test (PCPT) Sounding to depths of 100 ft (30.5 m) within the building footprint. Additionally, borings were performed to envelope the building. Deep foundation alternatives included driven concrete, monotube, and steel pipe pile as well as drilled shaft. Following an evaluation of high structural loads, site-specific constraints, foundation test data from buildings 1 and 2, and preference expressed by the project owner, a pre-cast prestressed concrete (PPC) pile-supported foundation system was selected as an economical and effective foundation approach. Use of an augered cast-in-place (ACIP) pile foundation system was precluded by the project structural engineer. This paper deals with the design aspects and methodologies utilized in choosing and economizing the foundation system. The building foundation was designed for an allowable pile capacity of 40 tons (353 kN) in compression, 1.5 tons (12 kN) in lateral capacity for a deflection of 0.25-in (0.64 cm) and 15 tons (133 kN) in uplift capacity. For the single story extended garage structure, a pile capacity of 27 tons (238 kN) was indicated in compression. As part of the design process, an extensive probe pile driving program was carried out in order to evaluate the pile driving equipment, determine and verify pile capacities, and optimize the production pile lengths. A total of 33, 14-in (356 mm) square, PPC concrete piles were driven within the entire building limits, and dynamically load tested utilizing Pile Driving Analyzer (PDA) as part of the probe pile driving program. Utilization of PDA during probe pile driving helped in predicting pile set-up (i.e., increase in pile resistance with time) as well as reducing the pile lengths by as much as 20 percent. It resulted in variable pile lengths during the production phase. This information was effectively utilized as part of the overall quality control program to install a total of 559 PPC piles (including 33 probe piles) within the Building 3 footprint, including the reclaimed lake area, to depths ranging from 45 to 58 ft (14 to 18 m) below existing ground elevation as part of the foundation support system. Prior to installation of probe or production piles, a termination criterion was established using 1-dimensional wave equation analyses in addition to the design pile embedment requirement. The predicted pile capacities compared reasonably well with the capacities from the CAPWAP analyses for probe piles. This engineered, monitored and tested foundation solution provided a cost effective and satisfactory basis for completion and approval of the foundation work for the building resulted in cost savings over other foundation alternatives for the owner. The building has since been occupied and a recent reconnaissance has indicated that the building foundations are performing satisfactorily.

Jan 1, 2003

By Mohammad Nasim

Vertical expansion of existing structures frequently requires foundation retrofitting to enhance the capacity of existing foundations for supporting additional loads. Owing to their small diameter, a variety of suitable drilling methods available for installation, and smaller installation equipment capable of operating under limited headroom conditions, micropiles are often preferred for foundation retrofitting. This paper presents a case history demonstrating application of micropiles to underpin the existing foundation of the Washington D.C. Children?s National Medical Center (CNMC) for its future expansion. Located at 111 Michigan Avenue in northwest Washington, DC, portions of the hospital currently extend five stories above grade and three levels below-grade as parking garages. The hospital intends to expand the surgical wing up to the current build out (five stories) above the remaining portion of the existing parking garage. The original foundations consist of 80-ton Raymond Step-Tapered piles. New loading on the foundations required each Raymond pile to be capable of supporting 150 tons. Results from quick load tests on existing piles indicated that two entire column lines (Column Line A and B) would experience loads beyond their capacity, requiring enhancement of the existing foundation at these locations. The design and construction of the foundation upgrading work was particularly challenging due to various project constraints related to a high groundwater table, micropile installation under limited head room, and ensuring that the parking garage remained fully operational for the entire duration of construction. The paper presents the challenges faced during testing of existing foundations amid a high groundwater table, design developments of underpinning options to support the additional column loads, difficulties and challenges encountered during installation of the micropiles and construction of the micropile pilecaps, and value engineering options developed during various phases of the project. Understanding that micropiles are often a preferred option for foundation retrofitting, the case history is expected to provide a baseline design approach and innovative solutions to typical challenges faced during construction, thereby reducing potential cost overruns during design development and construction of similar future projects.

Jan 1, 2008

By S. H. Miller

Biodegradable hydraulic fluids can save tens or hundreds of thousands of dollars in fines and clean up costs in the event of a hydraulic fluid leak or spill. When properly selected, applied, maintained and monitored, a biodegradable fluid will have a long useful life and will protect equipment as well as or better than conventional petroleum based hydraulic fluids.

Jan 1, 2000

By Adriaan van Seters

"Abstract The content of Eurocode 7 – Part 1 and Part 2 – with respect to piled foundations is outlined. The important role of pile testing is presented and the derivation of the characteristic value of pile bearing resistance is explained. Recommendations for the use of correlation factors are given. The ongoing work of the Evolution Groups on piling is to prepare a revision of Eurocode 7 after 2019. Future topics and changes are highlighted.General outline of pile design by Eurocode 7In his paper for this conference Frank (2014) outlined the various aspects of standardisation for pile foundations, which involves Eurocode 7 as leading for pile construction in Europe. Standards for pile testing and execution of piling works were established in the last 15 years.This paper focuses on the design of piled foundations according to the design code Eurocode 7, which consists of 2 parts:EN 1997-1 Geotechnical design - Part 1: General Rules (CEN, 2004);EN 1997-2 Geotechnical design – Part 2: Ground investigation and testing (CEN, 2007) In Eurocode 7-1, Section 7 – Pile Foundations - deals with the design of piles. The safety concept for pile design is given in Section 2 – Basis of Geotechnical Design - for the three Design Approaches.In Section 7 presents the design of piles according to four methods:1. Results of static load tests2. Empirical or analytical calculation methods3. Results of dynamic load tests4. Observed performance of a comparable pile foundation.Guidelines for the ground investigation for piles is provided in Eurocode 7-2, Annex B.3. In the Annexes of Eurocode 7-2 examples of analytical methods to determine the bearing resistance of a single pile based on the results of various ground investigation techniques are given. Thus calculation models are presented based on design using the results of Cone Penetration Tests (D.6 and D.7) and Pressuremeter Tests (E.3). The Annexes of Eurocode 7-2 are informative.For the interpretation of Eurocode 7, reference is made to Frank et al (2004) and Bond and Harris(2008)."

Jan 1, 2014

By Richard J. Finno

Detailed measurements made at a test section adjacent to a deep braced cut and other published data are combined to illustrate the limitations of the common methods of predicting movements associated with excavations in soft to medium clay. While past performance data can be used to estimate expected responses before construction in many cases, actual wall and soil deformations throughout construction can only be estimated using finite element procedures. Success of such analyses depends equally upon considering all aspects of construction that induce strains in adjacent soil, such as wall installation, excavation and bracing sequence, and time, and adequately modeling soil stress-strain behavior. Even when these two criteria are met, soil deformations can not be predicted adequately when strain levels exceed those that produce peak shear stress.

Jan 1, 1991

By Shamsher Prakash

Equivalent spring constants for analysis of footings is a function of Young's modulus of pile material (Ep), shear modulus of soil (Gs), and geometry of the footing and/or piles. Shear modulus is strongly strain dependent in soils. Therefore, the spring constants are strain dependent, which is acceptable to the Geotechnical engineers. However, structural engineers prefer to use spring constants as a function of displacement, rather than strain. In order to develop these relationships, appropriate relationships between strain and displacement are needed. Also, modulus degradation with strain needs be built into these relationships. Description of spring constants kx , ky, and kz in x, y, and z direction and k?, k?, k?, about x, y, and z directions are relatively simple. However, description of kxø and ky?, the cross-coupling spring constants depend on 2 - components of displacement and rotation. Thus, there are 8 spring constants and likewise there are 8 damping constants. Approximate strain-displacement relationships on which displacement dependant k's and c's are based are presented with appropriate equations, and a numerical example is included illustrating k's and c's as functions of displacement.

Jan 1, 2002

By Thomas Lardner

Excavation for The Bow, EnCana, in downtown Calgary, occurred between May 2007 and September 2008. A monitoring programme was used to determine the behaviour of the shoring wall, soil and bedrock during the excavation for the 21 metre (69 ft) deep excavation with a footprint of approximately 17,000 m2 (183,000 sq ft). Results from the inclinometer readings indicated that significant horizontal movement due to a weak rock layer and shear band effect. These modes of movement account for up to 100 mm (4.0 in) and 45 mm (1.8 in) of lateral deflection, respectively. Based upon the results of the monitoring programme, rock samples were collected from the weak mudstone bedrock, with great difficulty, to determine the strength and deformation parameters. Results from the uniaxial compression tests indicate a UCS around 830 kPa (120 psi) and elastic modulus between 80 and 180 MPa (11 and 26 ksi). Mohr-Columb parameters were determined to be c' = 340 kPa (49 psi) and f' = 24°. Residual strengths were determined to be c'r = 0 and f'r = 15°. Using the results of the laboratory tests and field investigation records, an initial finite element analysis was conducted. Results of the analysis show good correlation when compared with the observed monitoring deformation, indicating accurate portrayal of rock parameters. Additional analysis and investigation is required to determine the principal horizontal stresses in magnitude and direction.

Jan 1, 2010

By Allan Sylvester

Construction of the Shot Tower Metro Station in Baltimore, Maryland was performed in two phases. In the first phase, a contractor was retained to excavate the station in order to construct twin tunnels from the Shot Tower Station to the John Hopkins Station. The retention system for this 70' deep excavation consisted of a Soldier Pile in Tremie Concrete (SPTC) wall supported by cross-lot bracing. In phase two, The Clark Construction Group, Inc. was retained to construct the station interior structure, two entrances, two station ancillary shaft structures and the track work for the station and tunnel. The excavation for the construction of the two entrances adjacent to the 70' deep station SPTC wall had to proceed prior to completion of the station structure due to the tight construction schedule. A system of overlapping secant piles was specified as a vertical support of excavation element for the West Entrance. The secant piles would have provided a watertight, rigid support to resist the load from the SPTC wall constructed in phase one. A watertight system was required in order to minimize the settlement of adjacent buildings supported on wood piles. Clark Construction was concerned with the constructability, cost and performance of the specified secant piles and looked for other innovative methods of providing a watertight and rigid system. Substitution of a reinforced slurry wall in lieu of the secant piles was cost prohibitive due to the additional cost of concrete placed under tremie. Clark, being familiar with cement-bentonite cut-off walls and slurry wall construction procedures, proposed the construction of a PSHG wall, in lieu of the secant piles. The PSHG wall construction consisted of trenching 30" wide by 20' long by 60' deep panels under a self-hardening slurry. Once the excavation for a panel was completed, a 60' deep prefabricated soldier beam and lagging panel was placed in the slurry. The slurry design mix then self-hardened within the cure time, allowing excavation for the structure to proceed This paper will discuss the design, details and construction methods used on the PSHG wall and will compare the advantages of the PSHG system to conventional support systems.

Jan 1, 1997

By Dan A. Brown

The following paper was written by Dr. Dan A. Brown, P.E. Brown is an Associate Professor at Auburn University's Department of Civil Engineering. The paper was originally presented at a FHWA's Transportation Research Board meeting and is presented here with the author's consent. Construction and design of drilled shaft foundations in hard pinnacle limestone requires flexibility from all parties involved due to the variability of the subsurface conditions. This article describes some strategies which have been found useful in the Birmingham, Alabama area. The importance of well trained and experienced field personnel in these conditions is noted. It is also vital that engineers understand the construction challenges so as to provide both quality assurance and cost effectiveness in design and in the specifications.

Jan 1, 1991

By Pasi Korkeakoski

There are about 400 multi-storey buildings founded on wooden piles in the city centre of Turku in Finland. Soil conditions are variable from hard rock to very soft clay. Due to the soil conditions and ground water lowering there are basically four different types of underpinning projects. Under dimensioned cohesion piles in a deep clay layer, decaying cohesion piles, a combination of these two reasons and decaying end bearing piles in a thin clay layer area. Many different execution methods have been used such as impact driving, jacking and drilling and combinations of these.

Jan 1, 2000

By Nino Catalano

The combination of two top levels of cross-lot braces designed and installed to act as a truss, and vertical post-tensioning of the panels allow the unbraced excavation of a 36' span. Philosophy of Excavation Support System The excavation of interest is for the cut-and-cover box sections of the southern approach to the Third Harbor Tunnel, which is part of the Central Artery/Tunnel project in Boston, Massachusetts. The 60' deep excavation is located very close to an existing building which is supported by piles, as shown in Figure 1. Therefore, it was necessary to minimize ground movement which may damage the building.

Jan 1, 1994

By J. X. Wu

An investigation on the seismic damage to buildings with pile foundations in Tianjin region, was conducted after the earthquake which hit Tangshan in 1976. It showed that most pile-founded buildings have an excellent aseismic capacity. In this paper, several pile-founded projects suffering the seismic damage are introduced as examples, simplified calculations are made of the vertical bearing capacity of pile foundations and of the horizontal seismic force, and suggestions are presented in conection with the design of pile foundations in the liquified ground soil. The paper shows a frame structure which has a plie foundation with a box-shaped base. Analyses if its response to the earthquake has been carried out in accordance with the F.E.M. and results have been obtained.

Jan 1, 2010

By Fritz J. Klingler

From site demolition, to design, to construction, Detroit's new Tiger Stadium project is required to be completed within a short 2 ½ years from award of the design-build contract. Such extreme schedule requirements together with somewhat difficult ground conditions at the site, resulted in several challenges in the design and construction of the deep foundation system for the stadium. During the geotechnical investigation, an intermittent water bearing sand layer was encountered overlying the hardpan at the site. As a result, some concern developed regarding the potential for collapse of caisson bells within this layer, as well as the potential for flooding of the caissons during drilling. Although sand and/or ground water was encountered within about half of the caissons, standard drilling and belling methods were used, and adverse conditions were controlled in almost all cases through expeditious drilling, inspection and concreting of the caissons. This paper will present a summary of the ground conditions, design and specification requirements, and construction methods used to successfully install the caissons for this project.

Jan 1, 1999

By Mark R. Svinkin

Construction vibrations may be harmful to adjacent and remote structures, sensitive instruments and people. Construction vibration sources have a wide range of energy, displacement, velocity and acceleration transmitted on the ground. Effects of different dynamic sources and soil conditions on construction vibrations is analyzed. Consequences of construction vibrations are developed in various ways. It is important to assess intolerable vibrations before the beginning of construction activities. Guidelines for preconstruction survey are presented. Pre-construction survey and prediction of anticipated vibrations by IRFP method, monitoring and control of measured vibrations are important steps in preventing intolerable vibration effect.

Jan 1, 2000

By E. Mongilardi

The construction of large underground openings through cohesionless or weak cohesive soils and under the water table in particular, often requires a ground improvement to be done from the surface or ahead of the excavation face in tunnelling problems. To this purpose various injection procedures have been used in the past and new outstanding techniques have been developed recently, such as "jet-grouting", extending the feasibility range. The paper presents a review of basic principles and practical design criteria with particular reference to the newest trends of development. Case histories have been selected within the experience of specialist contractor Rodio Co. showing the variety of problems solved by manifold grouting procedures and layouts, in widely different soils ranging from the sandy-gravelly alluvia of Milan to the soft marine clays of Singapore.

Jan 1, 2010

By Paul J. Axtell

Two new railroad bridges in Kansas City, Missouri are founded on drilled shafts embedded into the soil and underlying shale. The uncertainty arising from the non-homogeneous, anisotropic nature of most shales, and the variability of shales across the U.S., makes it a difficult material to assign appropriate design properties. As was the case on this project, the uncertainty of foundation performance in shale can lead to overly conservative designs, particularly with drilled shaft foundations. An extensive Statnamic axial testing program was performed to verify that the load-settlement behavior of the drilled shafts would be acceptable for the intended railroad traffic. Axial Statnamic testing was applied in three increasing cycles of 927 kips, 1007 kips, and 3177 kips, respectively. The maximum movements recorded at the shaft head during each of the loadings were 0.052 inches, 0.062 inches, and 0.257 inches, respectively. The loads applied in each of the respective Statnamic tests were not sufficient to reach the capacity of the shaft; so direct comparison of measured and calculated capacities is not possible. However, evaluation of the estimated design capacity can be accomplished based on results from the Statnamic testing program by utilizing normalized load transfer relations presented by O?Neill and Reese (1999). Such comparisons necessarily require extrapolation of the data measured in the Statnamic tests following typical load-displacement response. Results indicate the Kulhawy and Phoon (1993) method for estimating side resistance in Pleasanton shale rock sockets, assuming a smooth socket, appears to agree well with observed behavior during Statnamic testing. Accordingly, the O?Neill and Reese (1999) method for estimating the toe resistance in intermediate geomaterials, assuming cohesive rock with Rock Quality Designation (RQD) between 70 and 100, appears to agree well with observed behavior during Statnamic testing. Finally, based on Statnamic testing at varying load magnitudes and normalized curves developed by O?Neill and Reese (1999), the contribution of side resistance to the capacity of a deep foundation can be determined assuming no load is transferred to the base of the foundation during lower magnitude testing. Furthermore, higher magnitude testing can provide a means to evaluate the accuracy of design end bearing calculations.

Jan 1, 2006