Search Documents

By G. F. Flaherty

THE property of Tashota Goldfields, Limited, in the Lake Nipigon area, Ontario, is located about 4 miles west of Onaman lake and 16 miles by winter road south-southeast of Tashota station on the transcontinental line of the Canadian National railways. The mine, formerly developed to a limited extent under the name of Tashota Gold mine, has, since late in 1933, been under the management of Minefinders Limited, who, in 1935, brought it into production on a 60-ton per day basis. During the winter of 1934-35, the writer was geologist at the property. The geological structure in the immediate vicinity of the mine workings lends itself well to analysis on the basis of the mechanical principles of folding. Since structure is of prime importance in the localization of the ore-shoots and of the host shear-zones at the property, the correlation of all structural details and their mechanical interpretation forms a working hypothesis of structural control for the direction of exploration and development work. It is believed that the structural relations here set forth may be found applicable in part, or at least suggestive, in working out the relations of ore-shoots to structure in the Sturgeon River area to the south, and in the Little Long Lac area to the southeast (Figure 1).

Jan 1, 1936

By Turgut Yalcin

"High-grade concentrates are achieved in flotation columns primarily due to the use of thick froth layers and wash water, both of which facilitate the drainage of hydrophilic minerals from the froth. However, conventional columns employ tall, non-agitated recovery sections for bubble-particle attachment that require high headroom and special gas spargers as well as imposing particle size limitations. These disadvantages can be all alleviated by carrying out the recovery part of the process in a mechanical or pneumatic cell which generate froth more conveniently and efficiently.This paper describes the combining of mechanical and column flotation in a single unit and discusses the influence of various parameters on the performance of the system.INTRODUCTIONIn a flotation process, some of the minerals lifted up to the froth phase may drain back to the pulp due to various reasons such as weak attachment of particles to air bubbles, bursting of air bubbles, agitation of froth, etc. Weakly floating and entrained hydrophilic minerals drain at a faster rate than the strongly floating minerals, and effective exploitation of such differential drainage can lead to cleaner concentrates.For a given mineral, if the rate of flotation from pulp to froth is k1 (min·1) and the rate of drainage from froth to pulp is k2 (min""1), then the net (overall) flotation rate of the mineral, k (min-1 ), will be [Lynch et al., 1981 ]:"

Jan 1, 1997

By R. M. S. Häggblad

The article deals with stabilisation and regeneration of Ce02 and Ce02/Zr02 based Pt water gas shift catalysts, subject to high initial deactivation. The reaction gas species effect on the catalyst deactivation was investigated by H2-TPR. Activity measurements enabled the effect of different promoters, some added to the Ce02 based catalysts and some to the Ce02/Zr02 based Pt catalysts, to be investigated. The catalysts were also characterised by BET and CO-TPR. Deactivated catalysts activity was restored by using various regeneration methods. Of the two selected carriers the Ce02/Zr02 based Pt catalyst showed the highest resilience to deactivation. For the two different carriers, Ce02 and Ce02/Zr02, Wand Re were the best promoters when the catalyst was subject to deactivation. Experiments with Hr TPR indicate a fast initial change in the platinum oxides concentration and composition. The CO-TPR was used to make conclusions about the various regeneration effects of water and oxygen on the catalyst. Finally it is suggested that not one deactivation mechanism is possible and which mechanism that dominates is dependant on the catalyst and the reaction gas composition.

Jan 1, 2005

By B. W. Smee

Glacial lake sediments or glaciolacustrine deposits form a significant portion of the Canadian, Scandinavian and Russian landscapes. Furthermore, 50 per cent of the Archean volcanic belts within the Canadian Shield area are covered wholly or in part by these deposits. Because of the high electrical conductivity and low hydraulic conductivity of these compact sediments, the application of geophysical (electrical) and geochemical techniques in such areas becomes a difficult task. The presence of these sediments has therefore hampered exploration for metallic sulphide deposits in some of the most important metallogenic environments of Canada. Similar problems exist in some tropical countries, such as Australia, where the overburden may be very conductive. In this paper, the extent and provenance of the glaciolacustrine deposits within the Canadian Shield are described. The geochemical and geophysical factors that hinder exploration in the clay belts are reviewed, with case histories of successful and unsuccessful applications of some of these techniques. The most successful geochemical technique used within glacial clay belts is the sampling of lodgement till beneath the clay cover, and the analysis of the heavy mineral fraction of that till. Surficial sampling has not been successfully applied. Some geophysical techniques, more specifically electromagnetic and magnetic induced-polarization techniques, have detected mineralization beneath substantially deep clay or saline overburden layers. Some suggestions have been made, such as the use of anions in hydrogeochemical surveys and the use of wide-band multi-frequency EM systems. When implemented, they will hopefully make the current geochemical and geophysical methods more effective in exploration for base metal sulphides within clay-covered terrains.

Jan 1, 1979

By R. J. MacLeod

"INTRODUCTIONThe removal of water or liquid from slurries and solutions is a procedure generally present in many process industries. This has prompted the development of many mechanical and thermal devices with which, I have no doubt you are al1 familiar.In the mining industry, beneficiation of ores necessitates ' the removal of water or other 1iquid from the concentrate material. The most common method of accomplishing this is by means of thickeners, vacuum filters and rotary dryers, generally all three and in that order;The use of spray drying techniques to obtain the same end has many advantages and these will be outlined here.THE PRINCIPLE OF SPRAY DRYINGA Spray Dryer consists of a cyclone shaped chamber where hot air and atomized concentrate are introduced in the upper section. (Sec figure No. 1). Efficient mixing of these two streams produce dry concentrate and moist spent air, both of which are removed from the base of the chamber.Thermal dewatering involves the product ion of heat and spray drying has no special requirements in this area. Generally a direct fired air heater is used and the products of combustion whether they stem from the use of gas, oil or coal fuel go into the spray dryer along with quench or dilution air which is used to reduce the combustion gases to the desired temperature. This generally lies in the range of 1,000 to 1,600° F. In spite of these relatively high inlet temperatures, the spray drying process eliminates the need for refractory lining or indeed any special heat resistant metals except on the air inlet ducting. Waste heat may also be used even if a significant amount of contamination is present."

Jan 1, 1972

By I. I. Betcherman

INTRODUCTION A DISTILLATION process offers one of the most effective methods of refining metals. Its use is particularly attractive in the case of reactive metals which are not readily treated by pyrometallurgical or electrolytic methods. The 1ow vapour pressure of most metals severely restricts the applicability of the disti1lation process and only one or two metals may be effectively treated under atmospheric pressure at a reasonable temperature. If operations are carried out under reduced pressure several additional metals may be effectively distilled. Table I shows the vapour pressure of a number of metals together with a value of the free energy of formation of their ?oxides. Zinc and cadmium head the list and for many years? they have .been effectively refined by distillation. Sodium, magnesium, and calcium follow in descending order, and they may be distilled readily in vacuo and with difficulty at atmospheric pressure. Sodium, which is not of great metallurgical interest, is not considered. Magnesium has recently been produced in considerable tonnages by distillation methods ( 3). This paper describes the vacuum distillation of magnesium and calcium, their separation from each other, and their separation from less volatile impurities.

Jan 1, 1951

By M. M. Williams

WESTERN CAN ADA'S coal industry has experienced a serious set-back since 1949, following a pattern well known to its counterpart in the United States. The loss in coal markets in Western Canada has been particularly severe as the discovery of large reserves of oil and natural gas and the subsequent construction of re-fineries and pipelines roughly coincided with the dieselization of both main railways. While the coal industry will have to face a further decline in markets of long standing, others with a large growth potential can be se-cured if present marketing methods are changed where needed and if fundamental and applied research programmes are actively pursued. The energy and chemical potential of Western Canada's coals will eventually find their place in the ever-growing needs of industry and electric power producers. Electric power generation would appear to offer the largest and most immediate market for coal. If the coal industry is to serve this market adequately and gain as much of it as possible, coal operators ? must have a good knowledge of certain characteristics -of the electric utility industry and its fuel requirements. This paper is prepared primarily to set out some of these characteristics, but also discusses other probable markets for coal.

Jan 1, 1958

By G. Van Weert, O. Wang

ABSTRACT: When exposed to microwaves, rocks containing sulphides adsorb energy preferentially over barren gangue and quickly become warmer with minimal energy consumption. This effect makes subsequent machine sorting of ore from waste rocks or overburden possible using infrared sensing. This paper reports on the 2450 MHz microwave response of a variety of sulphide minerals by mesh size and spatial distribution, as they might occur in ore rocks. The implications for infrared ore sorting are discussed.

Jan 1, 2011

By G. Van Weert

ABSTRACT When exposed to microwaves, rocks containing sulphides adsorb energy preferentially over barren gangue and quickly become warmer with minimal energy consumption. This effect makes subsequent machine sorting of ore from waste rocks or overburden possible using infrared sensing. This paper reports on the 2450 MHz microwave response of a variety of sulphide minerals by mesh size and spatial distribution, as they might occur in ore rocks. The implications for infrared ore sorting are discussed.

Aug 1, 2011

By Fazel G. Jahromi, Ahmad Ghahremaninezhad

Enargite (Cu3AsS4) is a major complex copper mineral and often is a carrier of invisible gold particles. Pyrometallurgical treatment of enargite is challenging due to the arsenic release to the environment. Hydrometallurgical treatment, on the other hand, appears to be a promising alternative for enargite processing. In an atmospheric enargite leaching process both the copper and arsenic from the mineral can be leached into a sulphuric acid solution and the arsenic can be simultaneously precipitated as ferric arsenate. The unlocked gold in the residue then can be recovered in a subsequent cyanidation circuit. The downside of the atmospheric enargite leaching in sulphate solutions is the slow leaching kinetics. In this study the effective parameters of the atmospheric enargite leaching process in ferric chloride media were investigated. All the experiments were carried out at temperatures below 100 °C. The process parameters that were investigated in this study included ferric, chloride, sulphate and cuprous concentrations, temperature, mixing rate and leaching slurry pulp density. It was found that the copper recovery rate increases with the addition of cupric chloride and also with raising the temperature. The highest leaching kinetics and the highest overall copper recoveries were achieved when cupric was initially added to the leach solution and at 90 ºC.

Jan 1, 2015

By F. J. Reichhardt

Abstract -The Molopo Farms Complex is a major, layered ultramafic/mafic, early Proterozoic intrusion which is totally covered by sediments of the Karoo and Kalahari Formations and situated in southern Botswana and northeastern South Africa. The approximately 3000 m thick, generally fine- to medium-grained ultramafic and mafic cumulates are intrusive into equivalents of Transvaal Supergroup sediments and lavas. Multiphase deformation resulted in tilting and segmentation of the Complex into individual tectonic blocks. Sr isotopes document at least two chemically distinct parental liquids which interacted in a complex manner to form an approximately 1000 m thick rhythmically layered succession which straddles the ultramafic/mafic boundary. Repeated mixing resulted in a complex cryptic layering pattern and numerous sulfide-enriched layers which contain significant PGE +Au concentrations.

Jan 1, 1994

By J. Peterson

A review of blast designs and improved blasting practices at the Ekati??Diamond Mine is presented along with the results of three blast-monitoring experiments. Blast monitoring was undertaken to investigate blast damage mechanisms in the mine's well jointed rock mass. Rock mass damage caused by production, pre-shear and wall control blasts was measured. Ekati??uses 270mm holes for production blasting, and 165mm holes loaded with a decoupled charge for pre-shearing. The production blasts are loaded with bulk emulsion / ANFO blends. The mine plan involves using 30m double benches. A 30m high pre-shear is drilled and blasted prior to the production blasting that is done with sequential 15m benches. This paper summarizes the monitoring equipment and data gathered to date.

May 1, 2001

By D J. Murray

This paper outlines the principles of friction hoisting and the components involved, and gives a description of a specific mine hoist. Friction hoisting is compared with conventional drum hoisting, and the depth of shaft at which friction hoists become more economical than drum hoists, with respect to power consumption, is determined. Introduction T HE purpose of this paper is to outline the principles of friction hoisting, to describe the components and to show the advantages of multi-rope friction hoisting. Some calculations are made to show that the power requirements and the initial costs of friction hoists are less than those of conventional drum hoists, once a certain depth of shaft has been reached. The use of multi-rope friction hoists is gradually superseding the employment of the conventional drum hoist in many parts of the world. It results in heavier payloads from deeper levels, an increase in shaft safe-ty and a more compact installation for protection against adverse weather conditions. It was observed that where drums and friction sheaves exceeded 30 feet in diameter, a number of mechanical disadvantages were being experienced;

Jan 1, 1965

By G. I. Mathieu, R. W. Bruce

Flotation schemes for the separation of molybdenite from other minerals are based on utilizing the Inherent hydrophobicity of molygdenite (Fuerstenau1). This natural floatability was attributed to the crystalline structure of molybdenite by Gaudin et al.2 who suggested that any surface formed by the rupture of van der Wall's bonds should be hydrophobic and, therefore, naturally floatable. Other authors argued that "natural floatability" is dependent of adsorption of hydrocarbon ions and/or molecu1es on the surface of the minerals. This theory, albeit-c questioned 1,2 has long been recognized in actual practice of molybdenite flotation as the latter in carried out with hydrocarbons, such as fuel oil, kerosene and stove oil. Although conferring ready floatability to molybdenite, these presents generally have little effect on other sulphides and silicates. However, talc is a noteworthy exception because of its innate floatability4. Not withstanding the reason for this behavior which has also been attributed to crystal structure2 its end results as in the case of molybdenite is an immediate flotation response to frothing oils arid kerosene, as was observed by Baranovski5, Sutherland and Wark6.

Jan 1, 1974

By D. Komljenovic, E. Lafontaine, J. Paraszczak

Availability of the production equipment used in underground mines has a substantial impact on production costs and, thus, on mine profitability. Appropriate collection of pertinent data and information, as well as use of adequate performance measures and their analyses, can help mine operators identify cost-effective opportunities to improve equipment availability. This paper presents study results aimed at reviewing and analyzing means and measures used to quantify equipment availability and its contributing factors (reliability, maintainability and maintenance support) in several Canadian underground mines. It overviews sources, as well as quality and quantity of relevant data and information, and examines performance measures and their definitions, as applied to surveyed mines. Problems concerning data acquisition and meaningfulness of the performance measures are discussed. The paper concludes with some suggestions and recommendations concerning several aspects of equipment availability assessment. Evidence suggests that the latter may become a more useful tool for mine operators in their efforts to reduce production cost.

Jan 1, 2008

By D. L. Koch, J. W. Tester, L. K. Sinclair

"In this study, hydraulic conductivity (K) geostatistics were used to predict residence time distribution of well-to-well flow. Flow profiles, fracture density measurements, and pumping tests were available from the highly fractured Florence Copper in situ leaching site. The flow profiles were used to establish the statistical distribution and spatial autocorrelation of K. Two tests were used for validation. The first test confirmed that fracture density and K are autocorrelated over similar length scales. In the second test, Monte Carlo flow simulations successfully recreated the results of pumping tests. Flow sim¬ulations were used to stochastically model well-to-well residence time distribution. RÉSUMÉ Dans cette étude, nous utilisons la géostatistique de la conductivité hydraulique (K) pour prévoir la distribution des temps de séjour (DTS) de l’écoulement entre les puits. Des profils de l’écoulement, des mesures de la densité des fractures et des essais de pompage existaient pour le site fortement fracturé de lixiviation in situ de Florence Copper. Les profils de l’écoulement ont permis d’établir la distribution statistique et l’autocorrélation spatiale de K. Deux essais ont servi à la validation ; le premier a confirmé que la densité des fractures et K sont autocorrélés sur des échelles de longueur similaires ; quant au second, des simulations d’écoulements de type Monte Carlo sont parvenues à reproduire les résultats des essais de pompage. Les simulations d’écoulement ont servi à établir un modèle stochastique de la DTS de l’écoulement entre les puits.INTRODUCTION In situ leaching is the circulation of a dilute acid or base solution in the subsurface, via a series of injection and recovery wells, to dissolve a target metal. In situ leach modelling requires forecasting the residence time distribution (RTD) of flow between wells. In fractured formations such as copper porphyry deposits, order-of-magnitude variations in hydraulic conductivity (K) can result in highly channeled flow, resulting in a heavy tailed RTD (Becker & Shapiro, 2003; Kang, Le Borgne, Dentz, Bour, & Juanes, 2015). Channeling through preferential pathways has impacted copper recovery at several past in situ leaching field tests (Cathles, Glenn, Lenzi, Nigrini, Deans, & Huff, 1978; Ahlness & Pojar, 1983; Schmidt, Earley, & Friedel, 1994; Sinclair & Thompson, 2015). The aim of this work is to combine multiple types of hydrogeological measurements to stochastically forecast the well-to-well RTD in fractured rock for the purposes of copper in situ leach modelling."

Jan 1, 2018

By Ning Zhang, Yan Chen, Qikang Yi, Linjian Ma, Guoan Wang

Laboratory tests were performed to explore the effects of frequency on the deformation property of rock salt subjected to cyclic loading under confining stress condition. A two-stage (transient and steady) evolution law of axial cumulative strain was obtained through cyclic stress-strain curves complied from the loci of minimum load of each cycle. The unloading modulus decreases with loading cycles/time as a negative exponential function. The damage of rock salt under cyclic loading is reflected by the degradation of elastic modulus. A unified damage evolution equation considering the effects of frequency and time was established based on the experimental results. A new creep damage model for rock salt was proposed by introducing the non-stationary modular components in Burgers creep equation according to the Lemaitre equivalent strain theory. Comparative study indicates that the new model can accurately describe the creep deformation and damage evolution of rock salt under different loading frequencies. This paper provides a more reasonable model and relevant mechanical parameters for the stability analysis of compressed-air storage cavern in the injection and withdrawal durations.

Jan 1, 2015

By M. Vallée

Several reviews of mineral project performance in the past 35 years indicate a pattern of occasional, but recurrent, mining project failures due to shortcomings in geological information and estimation, mineral processing and metallurgical testing, feasibility study objectives and requirements, and project start-up methods. A commitment to quality assurance and continuous improvement methods and to obtaining “ENOUGH DATA, OF APPROPRIATE QUALITY” is essential. Recent international and Canadian proposals for mineral resource and ore reserve definitions have taken a nonprescriptive stance that will undermine the formulation of requirements, guidelines and industry standards for efficient deposit delineation and estimation, and for the determination of project feasibility. To help reduce problems, every feasibility study supporting a mine development and production decision should be based on objectives and methods adequate to reach completion targets similar to the bankers’, as a good business target for a profitable project. In a resource/reserve system, the use of reserve should be restricted to a project that meets required technical, economic and legal feasibility requirements for successful project implementation, and the definitions of these categories should provide explicit limits. Current shortcomings will limit the ability of the Qualified Person to provide “adequate professional practice,” fulfill his/her professional responsibilities to his employer or client and provide adequate information to the investing public. We must take advantage of present opportunities for Setting New Standards for the new Millennium.

Jan 1, 2000

By A. K. Croteau

"At Craigmont Mines Limited, Merritt, B.C., the mining practice of trackless sub-level caving was started in the latter part of 1966. This type of mining was new to the mine personnel and the mining industry of Canada as a whole. Sub-level caving has presented many old and a number of new problems in maintaining the equipment used in this method. This paper will deal with some of these problems as they affect this particular mining operation. It will be impossible to review all phases of the equipment, but an attempt will be made to cover the most pertinent aspects in maintaining the drilling, mucking and hauling, and auxiliary equipment."

Jan 1, 1970

By J. Bélanger, B. Semlali, M. Grenon

RÉSUMÉ La conception des fosses ainsi que l'évaluation des ressources géologiques et des réserves minières sont désormais réalisées entièrement à l'aide d'outils informatiques spécialisés. Cependant, plusieurs analyses, pourtant essentielles à l'évaluation de la viabilité du projet, sont réalisées en parallèle sans véritable optimisation ni synergie avec l'ensemble des données disponibles. Cet article présente deux approches permettant d'intégrer certains types d'analyses aux modèles de blocs miniers. Ces approches permettent de quantifier la broyabilité du massif rocheux ainsi que d'étudier la stabilité des pentes minières à même les outils d'optimisation et de planification minières. Cette méthode permet dès l'étude de faisabilité d'un projet minier de maximiser les données disponibles, menant ainsi à une approche plus intégrée en conception minière. De plus, ces approches sont flexibles et permettent d'évaluer rapidement plusieurs scénarios, tout en laissant la possibilité de bonifier le modèle et de revoir la conception tout au long du projet minier.

Jan 1, 2010