Search Documents

By Thomas F. Nederpel

The production of zinc and zinc-aluminum coated strip can be reasonably accomplished on a single operating unit. However, if the hot dip coating line is equip d with only one mo 7 ten metal holding furnace, it is necessary to transfer liquid metal of different chemistries and reintroduce virgin material to obtain the 18" necessary balance of elements in the bath. Dofasco produces Galvanize and Galvalume on a coating line with a sin le liquid metal furnace and has developed not only an efficient liquid metal trans& system but also an effective means of reutilizing the zinc-aluminum mixtures without detrimental quality affects.

Jan 1, 1992

By R. G. Robins

The effective removal of arsenic(V) from process streams and waste waters by precipitation with excess iron(II1) is sometimes attributed to the formation of basic ferric arsenates. The authors have investigated this system extensively using a variety of techniques and conclude that the solid phase produced is iron(II1) oxyhydroxide (ferrihydrite) with arsenic(V) adsorptively bound to the 2-3 nm particles.

Jan 1, 1992

By S. Yin, A. Bogno, H. Henein, P. Natzke

Impulse Atomization (IA) (a single fluid atomization technique) was used to rapidly solidify Al- 4.5wt%Cu and Al-4.5wt%Cu-0.4wt%Sc under argon atmosphere. In addition to the IA-generated droplets, the same technique was used to produce strips by Spray Deposition (SD) of the same alloys on a copper substrate with and without oil coating. The rapid solidification microstructures were analyzed using Scanning Electron Microscopy (SEM). From the SEM images, the amount of eutectic and the secondary dendrite arm spacing (SDAS) were measured. These SDAS results lead to the estimation of cooling rate. The eutectic fraction coupled with the metastable extension of the solidus and liquidus lines of Al-Cu (Sc) phase diagram lead to the estimation of primary and eutectic undercoolings. A comparison of the solidification path of the droplets and the strips was done as well as the analysis of the effects of scandium.

Jan 1, 2015

By Suresh Sundarraj

A diffusion mass transport model for predicting the microsegregation in a solidifying and coarsening dendritic mushy region of a binary alloy is presented. Two versions of this model are tested; one based on expressing the solute concentration in terms of mole fraction and the other on expressing the solute concentration in terms of mass fraction. On comparing previous model data sets and conditions, used in the analysis of Aluminum-Copper systems, a number of inconsistencies emerge. These inconsistencies are resolved on identifying a single set of data and conditions which take account of compositional density changes, "non-linear" thermodynamics and dynamic coarsening. An additional investigation is carried out to study the effect of assumed cooling mechanisms.

Jan 1, 1992

By C. J. Newman

Prior to 1995, the smelting process at the Kennecott Utah Copper Corporation (KUCC) smelter consisted of Noranda reactors and Pierce-Smith converters. In the consideration of expansion opportunities, the existing process did not lend itself to a program geared towards processing the total output of KUCC mining and milling operations. During 1989 and 1990, a number of smelting options were evaluated. The final selection was the Outokumpu flash smelting process, coupled with the new Kennecott-Outokumpu flash converting technology. Facilities were designed and installed to process 1:0 million tonnes per year of copper concentrate, with the ability to expand to 1.2 million tonnes per year. Following the shutdown of the smelter facility utilizing the Noranda technology in May 1995, the flash smelting, furnace commenced operation in June with the flash converting furnace startup following a few weeks later. The smelter has achieved design production targets and environmental goals. Current operating rates are at or above design rates for concentrate and matte processing. Emissions are lower than the permit levels and equate to less than 3.5 kg of SO2 per tonne of copper. This paper outlines the design, construction, startup and the first two years of operation of the modernized KUCC smelter.

Jan 1, 1998

By M. K. Mohan

Lead recovery from process solutions contributes not only to the conservation of resources but also clean environment. Zeolites are natural aluminosilicates, which finds applications as catalysts and in wastewater treatment. In the present investigation, studies were taken up on the processing of Pb from process solutions by zeolites. Effects of pH of the solution, time and type of zeolite viz. chabazite, mordenite, erionite and clinoptilolite on the removal of Pb from solutions was investigated. Rate of sorption was found to depend on the pH of the solution and about 99 pct. recovery was observed at pH 6. Optimal conditions were established for the maximum recovery of lead from process solutions. Possible sorption mechanisms were proposed. The calculated adsorption constants calculated from Langmuir and Freundlich equations showed that the adsorption of lead on chabazite was strong.

Jan 1, 1999

By Richard A. Leiby

The recycling of lead-acid batteries in the United States has become a challenge as to how to balance ever increasing environmental regulation and cost with efficient operations. East Penn's captive secondary lead smelter has developed into a recycling facility producing lead, polypropylene, sulfuric acid, ammonium bisulfite, and non-hazardous discard slag. The emphasis has been to design a facility to comply with environmental regulations, to eliminate wastes, and to produce products, while at the same time, continuing to supply the company's battery manufacturing raw material needs.

Jan 1, 1993

By Toshihiko Emi

The quest for cleaner steel is driven by increasingly stringent requirements from the manufacturing and construction industries. Key issues are the occurrence and removal of inclusions; These are discussed in the context of the unit processes of deoxidation, refining, transfer and casting of molten steel. Process thermodynamics and kinetics are also discussed. Recent progresses achieved and problems yet to be solved are elaborated, and an integration of the unit processes into a system to produce extra clean, steels with better performance is presented.

Jan 1, 1999

By A. M. T. S. Bandara

The solubility of rare earth (RE) salts in aqueous solutions depends on many factors including the type of cations and anions in solution, their concentrations, temperature and the type of solid precipitated. Experiments were conducted using anhydrous La2(SO4)3 and Ce2(SO4)3⋅8H2O as solids and lanthanum(III) perchlorate prepared by dissolving La2O3 in HClO4 solutions as RE-sources. Solutions of H2SO4, H3PO4 and their mixtures in the presence or absence of Na+, Ca2+, Fe(III) or Al(III) as perchlorates served as test solutions. Saturated solutions and precipitated solids were assayed and characterized using standard techniques to show that the La(III) and Ce(III) ions precipitate as hydrated sulphates, phosphates or double salts with sodium, depending upon the solution composition. The change in solubility of RE-salts with solution composition and temperature is the result of the composite effect of changes in solubility products (pKSP) of salts, pKa of acids and other equilibrium constants for ion-association.

By Toshiaki Akahoshi

Keywords: Wasted catalyst, Hydrodesulfurization, Ammonium vanadate, Ammonium molyb-date, Hydrometallurgical process. The fundamental reactions have been investigated in order to develop a hydrometallurgical process for recovery of molybdenum and vanadium from wasted catalysts generated in the hy-drotreating desulfurization of heavy oil. The principal steps of the process are a mild oxidation roasting of the waste catalysts at temperature around 500°C, leaching of the target metal components with dilute ammoniacal aqueous leachates, selective precipitation of vanadic acid, and ammonium molybdate precipitation. The selective recovery of vanadium as vanadic acid is successfully performed using ammonium sulfate as a salting-out agent. Recovery of ammonium molybdate is based on large dependence of solubility of ammonium molybdate in ammoniacal solutions upon temperature and ammonium salt concentration. In this process, the solution after recovery of vanadium and molybdenum is recycled to the leaching stage of the roasted materials, and the ammonium salts in the process liquor is in the repeated use. Employment of am-moniacal system makes it possible to operate the roasting at much lower temperature than that for the currently operating process.

Jan 1, 2005

By Laurentiu Nastac, Ruslan Mudryy

"This paper investigates the solidification of cast energetic materials. An active cooling and heating (ACH) technology and a mechanical vibration (MV) technology were applied to achieve unidirectional solidification during casting and to reduce cracks, gas pores, and shrinkage defects. The design parameters of these technologies were developed via Computational Fluid Dynamics (CFD) modeling and thermal stress analysis. Concerning the ACH technology, the number of cooling/heating sections and their temperature profiles and time sequences were optimized based on the thermo-physical properties of the energetic material as well as the riser and mold diameter, thickness and type. The ACH technology will also decrease the thermal stresses during casting of energetic materials and therefore minimize the formation of potential cracks that may form during the casting process. The MV technology will help to remove air entrapped during pouring process and decrease the detrimental gap size between the projectile and the solidified energetic material.IntroductionCasting processes are widely employed in the manufacture of products with intricate shapes and, in particular, in applications where the material of the final product is sensitive to machining. It is especially useful in processing of energetic materials. The cooling conditions applied in the casting process can affect the quality of the final cast in terms of void formation, residual stress distributions, and mold separation. Substantial shrinkage is also observed due to the density change upon solidification [1-3]. Residual stresses are known to be closely related to the formation of cold cracks and hot tears during casting. The formation of a gap between the mold and the cast material is of critical importance due to its deleterious effect on heat removal and on crack formation. In the casting of energetic materials all these defects can significantly impair the detonation velocity, Gurney energy, and insensitive munitions characteristics of the formulation, and lead to catastrophic accidents in explosives handling [ 4-5]. Imposition of carefully controlled cooling condition is thus critical in optimizing the cast quality that could help avoid such destructive effects."

Jan 1, 2013

By K. D. Mondale

The chemical and physical properties of samples from ten sedimentary zeolite deposits. (representing chabazite, clinoptilolite, erionite and mordenite types), have been determined as a prelude to the development of a wet beneficiation process. The mineralogical composition of each deposit and such properties as morphology, size, apparent density, surface area, pore volume, relative hardness and zeta potential in solution have been determined. Some of these properties, especially apparent density and relative hardness, were found to differ significantly from textbook values. Based on differences in properties between the zeolites and their associated gangue minerals, a wet beneficiation process has been developed which makes use of selective grinding, sizing, sorting and gravity concentration. Additionally, an alternative upgrading process using flotation has been developed for one of the deposits.

Jan 1, 1988

By Takeshi Ohgai, Hisaaki Fukushima, Tetsuya Akiyama, Joon-Seo Ki

"Recently, an intensive attention has been paid to the electrodeposition of Zn-Cr alloy in the field of the production of super-highly corrosion-resistant alloy plated steel sheets for the next generation. In this study the electrodeposition of Zn-Cr alloys from the sulfate baths was conducted to investigate the codeposition mechanism of Cr with Zn. As a result, Cr was codeposited with Zn at higher current densities in both polyethyleneglycol(PEG)-free and PEG- containing baths. However, PEG made it possible to reduce Cr+ to the metallic state and Cr existed in the form of Cr(III) hydroxide in the deposits obtained from PEG-free bath. The measurements of the partial polarization curve of Zn and the pH in the cathode layer revealed that PEG acted as a polarizer to shift the cathode potential to the reduction potential of the composited hydroxides of Zn and Cr formed due to the pH rise in the cathode layer.1. IntroductionRecently, much attention has been paid to the electrodeposition of Zn-Cr alloys because of its application to the production of super-highly corrosion-resistant alloy plated steel sheets for the next generation1Hl_ Some researches have already tried to commercialize this type of steel sheet. High corrosion-resistance of this steel sheet is brought about by codeposited Cr in the alloys. According to Piontelli's classification5l concerned with metal deposition from aqueous solution, Cr belong; to an inert metal and its deposition is associated with a large amount of hydrogen evolution. Therefore the current efficiency for Cr deposition is extremely poor. It has been also reported that Cr is unable to codeposit in the electrodeposited Zn film in the absence of a certain additive in the solution. 0-compounds group colloids7l, ether group organic compounds8), 9>, peptide based compounds10l, etc., have been found to be effective additives to induce the codeposition of Cr with Zn. However, few studies have been made on the codeposition mechanism of Cr with Zn. In this research, the fundamental electrodeposition behavior of Zn-Cr alloys from sulfate baths was investigated to clarify the codeposition mechanism."

Jan 1, 1998

By Lionel Ryan

In 1996, the Dominican Republic operation of Falconbridge (Falcondo) developed a 5-year Process Control Plan in conjunction with the corporate Process Control group located in Sudbury, Ontario, Canada. This plan was further refined into an analysis of the areas of the highest potential economic return for the company with the reduction shaft furnace operation being the most promising. Historically, the reduction plant, which comprises 12 shaft furnaces, has been the bottleneck of ferronickel production. Since 1996 there has been a history of control development, and the current status is that all 12 furnaces are using advanced model-based multi- variable predictive control. The combination of advanced process control (APC), improved control system performance and improved process information management has resulted in an increased throughput of 6% per shaft furnace and a reduction in operating costs of 4.5 US cent/lb of Ni. This paper reviews some of the major milestones that have been achieved in this development Keywords: Advanced Process Control; Model Based Predictive Control; Connoisseur, Reduction Shatt Furnace; Nickel Laterite Ore; Ferronickel; MonitorMV

Jan 1, 2004

By Shadia J. Ikhmayies

Polycrystalline CdTe thin films were prepared by vacuum evaporation on glass substrates. The I-V plots which were linear were used to find the resistivity. A value of 2.10×106 .cm was obtained. The transmittance was measured in the wavelength range 400-1100 nm. The bandgap energy was found to be 1.48 eV. X-ray diffraction pattern shows that the material deposits in the zinc blend structure with one strong reflection from the C(111) plane. The scanning electron microscope image shows a uniform surface with a small density of large (mµ1£) grains scattered on the surface.

Jan 1, 2009

By P. A. Metz

The Fairbanks mining district has produced in excess of 7.5 million troy ounces of placer gold and 250,000 troy ounces of lode gold since gold was discovered in the area in 1902. The Fairbanks mining district is in the northwestern part of the Yukon-Tanana Upland Schist Terrane, an area of approximately 240,000 square km that has produced in excess of 21 million troy ounces of placer gold. All lode gold production from the terrane has been from the Fairbanks mining district, and all of this production has come from high-grade gold-quartz polymetallic sulfide veins. Gold grains in the vein systems range in size from several microns to several millimeters. The veins are localized in a complex metamorphic rock assemblage which includes greenstones and felsic metavolcanic and volcaniclastic rocks, meta-exhalatives and metasediments. Gold occurs in the metamorphic host rocks in association with arsenopyrite and arsenic-antimony sulfides which occur in lenses and disseminations within the host rock. Gold grains occurring in the metamorphic host rocks range. in size from sub-micron to a few microns in diameter.

Jan 1, 1987

By Xiao-hui Fan, Li-shun Yuan, Xu-ling Chen, Wei Lv, Min Gan, Yi Wang

"As the amount of ferrous scrap increases every year, it becomes more and more urgent to deal with this iron-bearing resource properly. This paper puts forward a method on resource-oriented utilization of ferrous scrap (cold-bonded pelletizing), and these cold-bonded pellets can be used as coolant in a converter. The influence on the pellets qualities by using different kinds of chloride as rust agents is studied, and results show that the strength of cold-bonded pellets increases significantly by using a combination of the three kinds of chloride -NaCl,MgClz,FeCh, their best dosages are 1.2%, 0.2%, 0.1% respectively. Other iron-bearing materials also have an effect upon the pellets strength, by adding 5% iron powder and maintaining for 48h, the compressive strength of the clumps surpass 2500N/A, dropping strength surpass 4 times/ A, and 10% iron slag or 20% steel slag can replace 5% iron powder while obtaining the comparative quality. The influence of different ratios of three ferrous scrap (converter mud, iron scale and dust) is further studied, and results show that when the ratio is 30% : 30% : 40%, the pellet strength reaches the maximum. After maintaining for 24~48h, the clumps can meet the mechanical as well as the physical-chemical requirements as BOF steelmaking refrigerant.IntroductionGreat amounts of converter mud, dust and iron scale are produced in steel production process. These materials are of great values, and their accumulation not only leads to environmental pollution, but also wastes the precious resources, which restricts the sustainable development of the steel industry [1,2] The main approach at present to dealing with the ferrous scrap is to add them into sintering. But in this way, the utilization factor of sintering and the quality of sinter decline while the energy consumption increases [3].Therefore, more advanced and efficient technology is needed to make the best of these iron resources. Cold consolidation of ferrous scrap is a simple process that has many advantages such as less investment, quicker effect, lower energy and lower cost [4-5] But the conventional maintaining period is too long, usually up to four-six weeks, and the pellet strength is low. Therefore, the key points of the cold-bonded pelletizing are to develop a new adhesive [4,5] to shorten the natural maintenance cycle and to improve the strength of the pellets. A method on resource-oriented utilization of ferrous scrap (cold-bonded pelletizing) is brought forward, and these cold-bonded pellets can be used as coolant in converter. After maintaining for 48h, these cold-bonded pellets can satisfy the mechanical requirements to replace the converter coolant [6]."

Jan 1, 2013

By M. A. Usman, E. I. Akpan, S. O. Adeosun

Preliminary studies on the extraction and characterisation of biodegradable lignin from palm oil fruitbunch (POFB) for carbon fibre production has been conducted. Centra lComposite Design was used to determine the optimum operating conditions for maximum yield and properties of the extracted lignin. Soda concentration (1–3 wt/vol%), temperature (50–90 °C) and reaction time (20–30 min) were analysed using Rcore software. Experimental results show that using reaction temperature of 90 °C, time of 30 min and 3 wt/vol% soda concentration yields 3.3 g of lignin from 30 g of the POFB. The path of steepest ascent from ridge analysis shows that with temperature of 130 °C, time of 40 min. and soda concentration of 3. wt/vol%, 8.7 g of lignin can be extracted from 30 g of POFB. Analysis of FTIR and SEM show that the lignin has the same structure in all cases with minimal impurities.

Mar 1, 2017

By Filippos Patsiogiannis

Laboratory size (4.5 kg) low carbon steel melts were deoxidized using Al and FeAl (33% Al), with and without synthetic fluxes, in alumina and zirconia crucibles. The dissolved oxygen, total oxygen, soluble aluminum, insoluble aluminum, silicon and carbon contents in the melt were determined as a function of refining time and temperature. It was observed that the reaction between aluminum and oxygen in solution closely follows thermodynamic equilibrium. Silica present in the alumina crucibles was found to be a source of oxygen for the melt, while this was not the case for zirconia crucibles. Reoxidation of the melt occurred through oxygen pick-up from the atmosphere. The extent of this reoxidation was found to be a function of oxygen content of the bath and the slag cover on the surface of the melt. The effectiveness of calcium-aluminate based fluxes in protecting the melt from the reoxidation and in increasing the rate of removal of inclusions was evaluated.

Jan 1, 1992

By Torn H. Okabe

A fundamental study was conducted with the purpose of establishing an environmentally sound recovery process for recycling of valuable metals, by combining scraps containing such metals. As an example, direct extraction and recovery of neodymium (Nd) in magnet scraps was investigated by utilizing liquid metal as an extraction medium. It was found that liquid magnesium (Mg) is a suitable extraction medium and can extract Nd from iron alloys with high efficiency at around I 100 K. The newly developed extraction apparatus for Nd is a mechanically simple and static device without moving parts, where the Mg extraction medium circulates due to differences in the temperature inside the reaction vessel. This developed device can simultaneously accomplish continuous extraction of metal Nd from scraps, re-extraction of Mg from Mg-Nd alloy and the eventual recovery of pure Mg. As a result, metal Nd with 98 % purity was directly recovered from magnet scraps under certain conditions. It was also shown that the extraction agent Mg could be reused. The results of this investigation show the possibility of establishing a new process for the direct extraction of Nd in pure metal form without oxidization.

Jan 1, 2003