Search Documents

By Matthew Wilcock, Kenichi Soga, Peter Wright

"This paper discusses how an existing grey cast iron segmental tunnel lining responds to construction of a new SCL tunnel transversely beneath with zero clearance; how the damage assessment for the existing tunnel was conducted for impact of longitudinal movement; how the tunnel is subsequently instrumented to observe both movement and stress manifestation at its longitudinal connections and how the results from the instruments compare with the prediction. An assessment of neutral axis of the tunnel in longitudinal flexure is also explored using interpolated horizontal displacement data from a conventional monitoring system. INTRODUCTION The Royal Mail Tunnel (RMT) (formely Post Office Tunnel or ‘Mailrail’) was constructed using semi-mechanised deep level construction techniques from 1914 and 1917 (Lee 1938). Commencing full commercial operation in 1926, the system was until 2003; conveying parcels the 6.5 miles between seven sorting offices in the center of London, and linking the system with main line rail stations, Paddington and Liverpool Street (The British Postal Museum & Archive 2013). A single tunnel of 2.74m internal diameter facilitated a bi-directional twin narrow-gauge (~611mm gauge) railway road system for electric driverless operation. The tunnel lining is segmental grey cast iron (grade 10) made up of six flanged segments and a smaller flanged key segment; constructed into a ring of width 508mm The external diameter of the tunnel is 2.971m. For further details of the tunnel lining and material properties are outlined by (Devriendt & Alhaddad 2014).London Underground Bond Street Station is a major station of the London Underground system in the very center of London; in its vicinity, the RMT runs west-east perpendicularly above the north south Jubilee Line tunnels. Historic survey record of the Jubilee Line’s (the then Fleet Line) construction in 1974 and its impact on the RMT case is documented in (Crossrail 1993): it is one of only a hand full of case-studies frequently cited when assessing the impact of new construction scenarios of this type; not least including the assessment of the same tunnel, at the same site some 40 years later, and the subject material for this paper: It noted significant vertical displacement of ~90mm to the RMT without noticeable serviceability or operational impediment."

Jan 1, 2016

By Vas P. Srinivasa

A comminution circuit is an important integral part of a mineral processing plant. Nearly 40% of the capital cost and 30 to 40% of the operating cost are taken up by the crushing and grinding circuit. Therefore, considerable care should be given to the design and selection of this circuit. Several factors affect the selection of a comminution circuit--energy consumption, avail- ability of the equipment, the remoteness of location, and availability of trained personnel, to mention a few. Each of these factors influences the choice. Selecting a comminution circuit strictly on lower capital cost may not be optimal. Crushing and grinding circuits are usually site specific and should be selected - only after careful analysis of all the factors involved. The objective of this paper is to show the effect of these factors, which are extranious to capital cost. Usually, the capital cost of a semiautogenous grinding circuit is lower than that of an equivalent conventional circuit. However, due to lower equipment availability and high power costs in certain locations, the economic advantage of lower capital cost is lost. Analysis indicates that a break even point occurs at a power cost of 5¢/kWh. This paper describes the procedure utilized for selecting the most economic comminution circuit and states the conditions applicable for each cominution circuit.

Jan 1, 1983

By J. K. Shurie

Calcined high quality bauxite is a staple raw material of the abrasive industry world-wide. The author discusses the factors which affect the economic value of calcined abrasive grade bauxite, and proposes an approach to the problem of estimating the relative value of available materials.

Jan 1, 1990

By A. Hammons

Automated temporary roof support (ATRS) systems have been incorporated into roof bolters since the 1970's. During roof bolting, many injuries have occurred from large pieces of draw rock falling inby the ATRS beam and tipping back into the operator's area. Other injuries have occurred due to smaller, sharp rocks falling onto the operator's hand and arm during initiation of roof bolt drilling. These injuries are attributed to weak immediate roof, sometimes called roof skin failure. Even though ATRS systems support the roof and provide a measure of protection against roof skin failure, additional hazards sometimes do exist immediately inby and outby the supported roof. Design innovations such as the ATRS mounted rocker pad deflector systems have been designed to improve the roof bolter operator safety. This paper will inform the reader of the hazards, machine evolution through different design solutions, and the current state of the art in preventing roof skin failure injuries when roof bolting.

Jan 1, 2009

By V. M. S. R. Murthy, Biswaraj Dash, Somnath Chattopadhyaya

Tunnel boring machine (TBM) has been in focus for the last few decades and is currently the most preferred excavation method for metro, hydro and irrigation tunnels. Tunnelling in hard and abrasive rock conditions, in particular, is adversely affected by a very low advance rate coupled with increased TBM disc cutter failures and cutterhead jamming, seeking an in-depth understanding of the design and operational processes of the boring components of the TBM. The cutterhead and disc cutter are the critical boring components of the machine, influencing the boring process significantly. These components directly interact with the rock and hugely influence the machine’s efficiency. This paper encapsulates a review of prior studies related to disc cutter design and the cutterhead design for hard rock TBM tunnelling. A design methodology for designing and selecting a disc cutter and a cutterhead is suggested. The design methodology has been applied for a hard rock tunnelling case, and suitable design specifications for the boring components were arrived at. The disc cutter and cutterhead specifications designed based on the suggested methodology closely match with that of deployed TBM specifications. It may be observed that except for the case of high-strength and high-abrasive rock (greyish quartzite), for the rest of the rocks, the suggested design can meet the desired advance rates.

Jan 31, 2024

By Robin P. Gardner

The development and use of short-lived radioactive tracer methods for the on-stream determination of residence time distributions in large-scale ball mills is described. Tests are reported on a pilot-plant ball mill with 0.43 m diameter and 0.86 m length and on an industrial mill with 1.83 m diameter and 2.74 m length. Tests with different tracer feed sizes indicate that the residence time distributions on both mills are independent of charge particle size. Similar tests are planned for a-large ball mill of 4.57 m diameter and 9.30 m length. No safety problems were encountered in these tests and none are anticipated in tests of the larger mill.

Jan 1, 1978

By Thien Sok, Yaojun Lu, Craig Gilbert, Jeremy Scott

Feedwells play a pivotal role in gravity thickeners, governing flow distribution, feed dilution, and flocculation condition during solid–liquid separation. This study presents an optimized design and digital prototyping framework for FLSmidth’s E-volute and E-Duc Feedwell systems, integrating advanced computational fluid dynamics (CFD) with quantitative criteria introduced at SME2024. Building on established FLS technologies, a series of novel configurations were developed and systematically assessed under full-scale and site-specific conditions. CFD provided quantitative insight into flow distribution, feed dilution, and flocculation efficiency, enabling iterative refinement of design parameters. The optimized feedwell demonstrated superior hydraulic performance, enhanced mixing, and improved flocculation outcomes. Beyond the specific design advances, the work highlights CFD as an effective and economical tool for digital prototyping, facilitating early identification of design limitations, reducing dependence on physical trials, and accelerating innovation. The methodology underscores the value of simulation-driven design in advancing feedwell performance and improving thickener technology.

Feb 22, 2026

By H. Sevim

In this paper, the research effort in simulating the operation of underground coarse-coal hydrotransport systems (UCCHS) is summarized. The equipment of the system to be simulated is already optimally selected by using an analytical optimization model. The purpose of the simulation model is to test the performance of the system and to obtain the distribution of the operating parameters such as water and power consumption, amount of slurry delivered to the preparation plant, etc. Knowledge of the distribution of these parameters is essential for the efficiency of the design and the operation of the system.

Jan 1, 1985

By A. Suarez, M. Menendez, M. R. Gent, P. Riesgo

"Recent requirements to reduce thermal coal plant emissions, and ultrafine coal's tendency to produce these emissions due to its typically high ash and moisture contents have limited the use of ultrafine coal. Ultrafine coal in beneficiation plants are usually either disposed of in tailing ponds at a loss in combustible material or disposed of by blending with coarser higher-grade products, resulting in a reduction in marketed product quality. A study of the options for processing ultrafine coal, consisting of < 200 µm hydrocyclone overflow, with 38.8 percent ash content is presented here. Ultrafine coal was processed based on 200-µm sieve bend and 10-µm hydrocyclone classifications, enhanced gravity separation (EGS) and froth flotation concentration as well as combinations of these. Yield, combustible material recovery (CMR) and product humidity were evaluated as test results.Depending on the processing applied, product ash content could be reduced up to 49.7 percent, and up to 95.8 percent CMR of the actual run of mill feed could be attained. All of the processing options analyzed could reduce produced thermal electric plant emissions due to ash and moisture from 22 to 38 percent of the actual unprocessed ultrafine coal product.Froth flotation was found to be the optimal process, yielding a product with the lowest ash content attained of 19.5 percent and CMR of 92.3 percent. Being the most versatile of the processes evaluated, it is capable of producing coal with varied ash contents but is subject to potential variations in coal flotability. The most complicated of the processing options, a combined sieve bend recovery of the > 200 µm fraction and EGS processing of the 10 to 200 µm fraction was found to be the next best option, attaining a combined 90.1 percent CMR and 25.0 percent ash content. IntroductionMunicipal, regional and national objectives to reduce fossil fuel combustion emissions and their effects on air quality and global weather changes are affecting thermal electric plant operations. Plans and regulations such as President Obama's Clean Power Plan (U.S. Environmental Protection Agency, 2015), the European Directive 2010/75/EU (European Commission, 2010) and China’s proposed Enhanced Actions on Climate Change (Wei, 2015) are of major significance to thermal electric plant operations. Although thermal plant efficiencies depend in large part on the losses of heat by plant components, the ash and humidity contents of thermal coal invariably reduce plant efficiencies and increase emissions of carbon dioxide (CO2), nitrogen oxides (NOx) and dust.Any noncombustible material present in thermal coal will result in higher CO2 emissions per unit of energy produced. Since no particle emission control can be totally effective, it is to be anticipated that any reduction in coal ash content will also result in reduced particle emissions. Kurose, Ikeda and Makino (2001) reported that NOx emissions also increase with coal ash content. The effect of coal moisture content during combustion is complex. Kurose, Ikeda and Makino (2001) showed that an increase in coal moisture content significantly reduces thermal NOx to total NOx production, and Bosoaga et al. (2006) showed that it tends to reduce NOx emissions. Since the humidity, pyrite and ash content of thermal coals directly affect thermal electric plant efficiencies and emissions, minimizing these factors should facilitate, at least in part, compliance with thermal electric plant emission limits. This, in turn, would affect the specifications and prices of the coal preparation plant products."

Jan 1, 2016

By Aimee A. Woolsey

Enterprise Unmanned Traffic Management is a holistic system concept evolving from technological developments in radio frequency where dynamic tracking can be added into current and emerging platforms. This is done through inexpensive RF sensors capable of real-time and cooperative, non-GPS tracking enabling digital visualization of assets, including unmanned aerial systems (UAS). The RF sensors are low size, weight, and power (SWaP), creating efficiencies in energy and material consumption while transmitting positions in real-time and at long ranges. Multiple UAS and other unmanned vehicles can be visualized for risk mitigation in operations,

Oct 17, 2022

By Danqing Gao, Brijes Mishra

Spatial variance of rock properties is an important characteristic of rock which addresses the heterogeneity of mechanical and physical properties and their effect on underground mining. Assessing spatial variance can be useful for both locating potential difficult grounds and performing reliability analysis in the mining support system. This study shows a microscale numerical model for rock material based on continuum mechanics. To consider the spatial correlation factor of mechanical properties in realistic rock mass, this study introduces a spatial correlation concept into the traditional type III extreme value distribution model. Based on the improved microscale random model, we conducted a series of numerical uniaxial compressive tests and one longwall mine model to investigate the progressive failure of rock. The results show that spatial correlation factor can significantly affect the load-deformation curves and fracture patterns. The spatial variance model was applied to a longwall mine that included several cutting sequences to observe the influence of the spatial variance on roof behavior. The cohesion and friction random fields induced failure that propagated randomly through the immediate roof in different entries. The results showed that the spatial variance provides an accurate prediction of erratic roof falls in coal mines.

Jul 20, 2020

By T. H. Bagan

The Sixteen-to-One Mine was originally designed and operated using Blasthole Stoping with end slicing as the primary mining method. This method changed to Modified VCR Stoping in response to efforts to control dilution. The new method combines Blasthole Stoping with shrinkage methods, pillars, and reduced sublevel intervals to provide the most practical dilution control avail- able for low cost bulk mining.

Jan 1, 1987

By Northcutt Ely

My topic today is our Nation&apos;s interest in the minerals beneath the oceans. I will state what I think should be our objectives, the means available to attain these objectives, and the obstacles to their accomplishment. It is possible that as early as this year of 1969 our country must make policy decisions on this subject, and that these, once made, will be almost irreversible. Two factors are hastening an. early decision. First, the 1958 Convention on the Continental Shelf becomes eligible for amendment after June 10, 1969, if the Assembly of the United Nations so decides. Second, the United Nations has created a permanent committee of 42 nations, which was preceded by an ad hoc committee of 35 nations, to study the question of the peaceful uses of the seabed "beyond the limits of national jurisdiction. While these measures purport to deal with the creation of a regime to govern mineral development on the deep sea floor beyond the limits of the jurisdiction of the coastal nations, it has become clear that the urgent issue is the extent to which this future regime shall acquire jurisdiction over the mineral resources of the continental margin, and receive royalties therefrom. This brings the proposal into potential collision with the interests of the coastal nations under the 1958 Convention on the Continental Shelf, including, of course, the United States.

Jan 1, 1969

By Shaoyang Yan, Xinming Chen, Huazhe Jiao, Huaibao Chu, Chang Wang

In terms of the technical problems of rib spalling in large mining height coal face, a long-distance advanced pre-grouting layer flexible reinforcement technology is proposed in this paper. Based on the mechanism and failure mode of rib spalling in the coal face, the mechanical properties of the aluminum plastic composite pipe were analyzed by using the tensile and compression experiment. The deformation and strength characteristics of “flexible pipe + grouting” specimens were studied by uniaxial compression test, splitting test, and shear test. The UDEC numerical simulation software was used to simulate the reinforcement effect of “flexible pipe + grouting” at different positions. Combined with the field application, the feasibility of long-distance advanced pre-grouting layer flexible reinforcement technology was verified. The test results show the following: The coal face has the characteristics of brittle and large deformation. The aluminum plastic composite pipe has the characteristics of good elongation and tensile strength, which can endure the large deformation of the coal face. The “flexible pipe + grouting” can improve the tensile and shear strength of coal. The UDEC numerical simulation analysis indicated that the grouting hole layout of “flexible pipe + grouting” has a significant difference in the reinforcement effect of the coal face. Compared with single row grouting reinforcement, the reinforcement effect of double row grouting holes 1.5 m and 3.0 m away from the roof is better. According to the field application, it is feasible to use aluminum plastic composite pipe as a flexible grouting pipe to reinforce coal seam with 80–100 m long-distance pre-grouting. Long-distance advanced pre-grouting layer flexible reinforcement technology can improve the daily production of coal and reduce the support cost of the coal face. As a new method of reinforcement, long-distance layered flexible reinforcement has a significant effect on the prevention and treatment of rib spalling in large mining height coal face.

Sep 27, 2022

By R. E. Lindstrom

The mineral bastnasite is utilized to describe alternate processes for the extraction and separation of the rare-earth elements by solvent extraction. The rare earths can be acid-leached directly or fused with NaOH before acid leaching. Cerium, the major constituent, can be recovered by fractional precipitation, fractional leaching, or solvent extraction with tri-nbutyl phosphate. The latter process is capable of producing 99.5-percent pure CeO2 at 98+ percent recovery. Lanthanum is subsequently recovered by fractional precipitation or solvent extraction with a nitrogen-based extractant. A 20-stage mixer-settler operation with a primary amine extractant results in a 95-percent pure La203 fraction at 96 percent recovery. Europium is amenable to extraction from most of the remaining rare earths with an organophosphate extractant. Selective stripping of the europium, followed by reductive precipitation, produces high-purity Eu203. Another possibility for europium purification involves the differential extraction of europium with an amine followed by a sub- sequent reducing strip. Separation of the remaining elements is more difficult but can be accomplished with amine or quaternary ammonium extracts. Typical separation factors achieved are 3. 8 for praseodymium-neodymium and 10. 5 for neodymium-samarium.

Jan 1, 1967

By Jonathan K. Hrica, Brianna M. Eiter

The ability to identify hazards during a workplace examination is a critical skill for mineworkers to have in order to maintain a safe workplace. While research suggests that being able to successfully recognize hazards requires a complex set of competencies, it is unclear which competencies are most critical to adequately perform a workplace examination. This paper presents a hazard recognition competencies framework as an explanation of the competencies that affect mineworker hazard recognition. To better understand how the industry is selecting and preparing workplace examiners, researchers fromthe National Institute for Occupational Safety and Health (NIOSH) interviewed nine health and safety (H&S) professionals at surface stone, sand, and gravel mine sites throughout the USA. A primary purpose of these interviews was to verify the competencies included in the hazard recognition competencies framework and to understand why these competencies are critical. Finally, the results of this study are presented within the context of current NIOSH research findings related to hazard recognition.

Jul 27, 2020

By Tom B. Corry

INTRODUCTION Located approximately 48 km (30 miles) south of Dallas, Texas, use to be the site of the Superconducting Super Collider. For those of you unfamiliar with the project, this was a multi-billion dollar project taken on by the U.S. Government for the further advancement of technology, medicine, and science. Major components of the project consisted of a Linear Accelerator known as the LINAC; three accelerating rings known as the Low Energy Boosters (LEB), Medium Energy Booster (MEB) and the High Energy Booster (HEB); the East and West Campuses where the Inner Reactor Halls would have been located; and the 87 km (54 mile) main collider tunnel. Unfortunately, this all came to an end on December 6, 1993, with the termination of the project due to the Government&apos;s cancellation of funds. This paper will deal with the two of the underground contracts before the termination. These two contracts were the 1122 contract which ran from N25 to N40 and the 1130 contract which ran from N40 to N55. (See figure 1) The 1122 contract was awarded to us in July of 1992 and consisted of the excavation and support of six (6) shaft varying in diameter from 5.5 m (18 feet) to 8 m (26 feet) and ranging from 39.6 m (130 feet) to 61 m (200 feet) deep and the driving of approximately 13,100 m (.43,000 If.) of main collider tunnel. Our second contract, the 1130, was almost identical to our first

Jan 1, 1995

By Lauren M. Roberts, Ralph R. Sacrison

Pipeline or borehole free-fall transfer of material has long been done in support of underground mining. This paper addresses some characteristics and design elements in selecting systems suitable to the transferred media and the mine requirements. Though aspects of overall systems are discussed, principal attention is directed to the slickline/dropline/transfer line and the discharge diverter/rockbox/energy dissipator/boot. These terms are common to these systems, often used interchangeably, and will be used as appropriate to the material, equipment and construction. Following several design sections, fabrication and construction, and system operating and maintenance procedures are discussed.

Feb 1, 2025

By J. D. Miller

"It is now possible to use 3D X-ray tomography analysis for plant-site characterization of coarse particles at a sampling rate of about 3 kg/min for particles which range in size from 150 mm to 1 mm at a voxel resolution of about 150 microns. This is quite a significant advance in X-ray tomography technology and should be useful for plant-site coarse particle characterization (size, shape, composition, density, texture, grain exposure, mineral liberation) with a response time of minutes after receiving the sample. Applications in the mineral industries are discussed including the coal industry, aggregate industry, metal mining and the processing of industrial minerals. INTRODUCTION Plant-site characterization of coarse particles at coal preparation plants, crushed stone/aggregate plants, and mineral processing plants is needed to improve plant capacity, product quality, and/or process efficiency. Not much on-line coarse particle characterization is done at these plants. Some limited information regarding particle size is obtained on-line from reflected light images using systems such as the OPSA, Split, and WipFrag analyzers. Even laboratory analysis of coarse particles has been difficult because of the large amount of sample required to insure statistical significance of the results. During the past decades laboratory 3D characterization of particles from energy and mineral resources by X-ray tomography has been demonstrated and used to good advantage [1, 2]. 3D X-ray tomographic analysis had its origin in the medical services industry; it is used to provide internal images of the human body and now has also been developed for non-medical applications [3]. Figure 1 shows a schematic diagram for the cone-beam geometry micro-CT system. In our case X-rays from a microfocus X-ray generator are partially attenuated by the sample (a packed bed of particles) that is made to rotate in equal steps in a full circle about a single axis of the particle sample. At each rotational position, the surviving X-ray photons are detected by a planar two-dimensional array (image intensifier) large enough to contain the shadow of the specimen. These two dimensional projection images are collected using conventional video technology. The video signal for each projection is then converted to a two-dimensional digital array by an image processing system. Finally, a three-dimensional image is reconstructed from the collected set of projection images. With the availability of automated high speed X-ray tomography [4] it now seems possible to do plant-site particle characterization at a sampling rate of about 3 kg/min for particles which range in size from 150 mm to 1 mm at a voxel resolution of about 150 microns. This is quite a significant advance in X-ray tomography technology and should be useful for plant-site particle characterization (size, shape, composition, density, texture, grain exposure, mineral liberation) with a response time of minutes after receiving the sample. Applications in the mineral industries are discussed including the coal industry, aggregate industry, metal mining, and the processing of industrial minerals"

Jan 1, 2016

By James C. Barker

Alaska?s known mineral endowment includes some of the largest and highest grade deposits of various metals, including gold, copper and zinc. Recently, Alaska has also been active in the worldwide search for sources of rare earth elements (REE) to replace exports now being limitedby China. Driven by limited supply of the rare earths, combined with their increasing use in new ?green? energy, lighting, transportation, and many other technological applications, the rare earth metals neodymium, europium and, in particular, the heavy rare earth elements terbium, dysprosium and yttrium are forecast to soon be in critical short supply (U.S. Department of Energy, 2010). The REE, accompanied by other high field strength metals (such as Nb, Zr, Ti, Th, W), are associated with alkaline complexes of the Hogatza Belt in northwest Alaska; peraluminous tin-granites of the Ruby batholith in central Alaska and the Porcupine plateau in the northeast; and peralkaline intrusive complexes in the southwest Alaska Range west of Anchorage, and on Prince of Wales Island in southeastern Alaska. Limited evidence suggests that the heavy REE are associated with deposits that became more highly evolved by late hydrothermal processes.

Jan 1, 2012