Search Documents

By O. Dojcar

The results of a laboratory investigation of rock fragmentation conducted with a model material were partially verified under field conditions. The object of the investigation was to study the qualitative and quantitative relations between the parameters of the primary blast and fragmentation to enable the planning of an economically efficient degree of disintegration with optimum utilisation of the blast energy. The three blast parameters that were considered were burden, specific charge and the ratio of spacing to burden

Jan 1, 1991

By W. E. Stephens, A. J. Boyce, D. Lowry

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. An integration of S isotopic, fluid and mineralogical data for granitoid-related mineralisation showed that the porphyry systems had a predominantly subcrustal magma source, but the inner magma pulse of two-mica granite in the Fleet pluton was derived mainly from reduced sediments. The porphyry-style mineralisation formed from boiling fluids at high crustal levels, with a moderately saline fluid percolating down to the upper veins as they cooled but not penetrating the deeper Talnotry deposit. Veins in peripheral greywackes have a significant magmatic component but also incorporated CO2-rich components and metals released by dewatering of host sediments in response to granitoid intrusion. The low grade of regional metamorphism resulted in the significant fluid input from country rocks which led to the more exotic mineral compositions, especially where argillaceous sediments were involved

Jun 19, 1905

By G. B. Harris, A. R. Laplante

Fine tungsten was used to mimic gold and fine and coarse silica and magnetite to mimic gangue. The optimum flow rate of fluidisation water varied from 1.7 l/min for fine silica to 5.6 l/min for coarse magnetite. Overloading at optimum flow rate was then investigated. With fine silica gangue no overload occurred under any of the conditions studied, and there was very little overload with fine magnetite. Coarse silica caused appreciable overload, but only after a significant bed of tungsten had been formed; with fine magnetite gangue the onset of overloading occurred earlier. Finally, with coarse magnetite severe overloading occurred almost immediately. Overloading was modelled using a first-order kinetic rate constant for erosion of the concentrate bed and a critical mass of constant above which it takes place. The results clearly demonstrate the importance of removing oversize to maximise recovery, particularly with a high-density gangue

Jun 18, 1905

By Boorder De, B. S. Panov, A. B. Westerhof, V. A. Korcemagin

Paper presented at the conference on Economic geology in Europe and beyond II, models for <mineral deposits> in sedimentary <basins>, held in Keyworth, UK, 13-14 April 1994. The Hg and Sb deposits of the Mediterranean and Circum-Pacific Belts are often found at elevated structural levels, suggesting that their preferential occurrence in young orogenic belts is not a fundamental metallogenic feature but merely reflects their chances of surviving post-orogenic peneplanation. In western Europe their emplacement appears often to be related to late orogenic extensional events accompanied by a notable increase in heat flow. Although Nikitovka and Almaden have quite different settings, both appear to be related to deep-reaching shears. Together with brittle fault zones at higher levels, these provided pathways for fluid phases that originated at least partially within the mantle. The Nikitovka deposits are located in the Donets segment of the 2 000 km Pripyat-Dniepr-Donets palaeorift in the East European Platform. Initiated in the mid-Devonian with a possible Precambrian precursor, its listric boundary faults displace the Moho from a depth of about 50 km north and south of the rift to 35 km along the axes of the Pripyat and Dniepr segments. The steep central anticline of the Donets segment, within which the main Hg-Sb district is located, is interpreted to be associated with a reactivated fault reaching into the upper mantle. The Almaden syncline, formed during the Variscan Orogeny, may be an older pull-apart basin or half-graben associated with the collapse of the Cadomian Orogenic Belt. It is situated on a major ENE-WSW-striking shear zone which may represent a Late Cadomian transfer zone reaching into the mantle

Apr 1, 1995

By R. G. Kidel, S. C. Doming

The project has shown that it is feasible for a junior company to reopen a narrow vein-style gold mine and successfully take it into production. An intimate understanding of the mineralisation and a flexible approach to mining are crucial, as are stringent cost control and efforts to keep overheads low. The project has confirmed the geological complexity of the Main Lodes, which consist of highly sheared quartz-sulphide infill in strongly sericitised granodiorite. The existence of discrete high-grade zones within the Hangingwall Lodes has also been confirmed. Broad low-grade zones continue to be recognised and require the local application of bulk longhole mining methods. The initial mine plan called for predominantly longhole stoping, but adverse ground conditions have meant that a switch to air-leg mining has produced higher run-of-mine grades. The excess capacity at the processing plant can best be used by batch processing, with its reduced maintenance requirements

Jun 21, 1905

By P. J. Baguley

The model has been developed on the basis of the observation that the partitioning behaviour of a particle is related to its calculated terminal velocity. It utilises a theoretical calculation of the terminal velocity of each particle class. This is then correlated with the observed partition data for a plant separator using empirically-derived functions of operating conditions which take into account effects such as bath turbulence, holes in drum lifters and feed arrangements. The model successfully decouples the effects of medium density and viscosity and is appropriate for any bath-type separator. The correlation between calculated terminal velocity and actual partitioning behaviour was established and modelled using data obtained from two Wemco drums treating Fe and Mn ores. The model can be used to predict the prevailing size-by-size partition curves and the separation (product grades/recoveries) given the washability of the feed and operating conditions. Simulations are used to show that, for the treatment of Fe ore, there is a maximum medium density beyond which product grades fall and that this maximum decreases as the proportion of magnetite in the medium increases. This is attributed to the dominant effect of viscosity at higher medium solids concentrations

Jun 18, 1905

By H. K. Taylor, B. Denby, L. D. Smith

Contributions by H.K. Taylor and G.A. Davis discuss the three papers published in Transactions IMM A, vols. 103 and 104, with responses by Smith and Dowd

Dec 1, 1995

By R. J. Gochin, M. A. Diaz

A modified Hallimond tube is described which allows the determination of the ultimate recovery R and the flotation rate constant k in a single, continuous experiment. The range of fine particles which can be satisfactorily floated with the modified apparatus can be extended by increasing the length of the bottom part of the tube. Findings suggest that pyrite and arsenopyrite can be separated in alkaline suspension using the so-called F series of collectors. Lime was found to act as a depressant. The collectors operate under pH and dosage control and do not require other depressants. Collectors used in the study were thio-amine (a cationic surfactant) and alkyl propionamide (a non-ionic surfactant)

Apr 1, 1995

By P. H. Carr, G. G. Marino, K. A. Patel

Extensions to a correctional institution at Wabash Valley, Indiana, required development over abandoned coal-mine workings, at 90 m depth, where subsidence was possible at surface. Backfilling of the flooded mine in critical areas was determined to be the most cost-effective method of limiting the risk of damage to the buildings. Containment grout was first placed in selected entries and cross-cuts of each mine area; the remaining volume was then filled with a readily flowing infill grout. Where a high proportion of an area was taken up by rubble, calcium lignosulphonate was used as a retarder and plasticiser to increase penetration. Grout movement was monitored from adjacent boreholes with an electrical resistivity probe during grouting, while after the work was finished core samples were obtained from verification holes drilled in the backfilled areas

Jun 19, 1905

By J. K. Whyatt, W. P. Blake, T. J. Williams

A study at the Idaho mine revealed that, despite the apparent randomness of seismic events, common characteristics defined five recurring types. These characteristics included the geological structure that slipped, the first-motion pattern and the location and intensity of damage. Many large events caused little or no damage, and where it did occur it was concentrated at intersections between slipping structures and mine openings. Of 39 events between 1989 and 1994 with local magnitudes of 2.5 or more, 10 were caused by slip on bedding planes in the southern limb of the mine, 6 occurred near the vein along a set of near-vertical faults that form the central shear zone, 8 were strike-slip events on the Southern Control Fault, 4 were by slip on the vein itself and 10 involved strike-slip and/or dip-slip movement along the North Control Fault. Strategies for control of mining-induced seismicity need to consider all five types of event, lest a strategy to reduce one type increases others

Jun 19, 1905

By A. K. Tripathy, P. K. Pattnayak, H. S. Ray

The effects of water addition on the solid-state reaction between Cr2O3 and Na2CO3 at low temperatures (up to 873 K) were investigated to determine its possible influence on the reaction rate and the degree of conversion to soluble chromate. Experiments at high temperatures were conducted for comparison. It was found that adding water to the mixture before roasting enhanced both reaction rate and yield significantly. The reactions followed the Lesokhin-Tempelman equation at low temperature and the Ginstling-Brounshtein equation at above 973 K; the respective activation energies were 95 and 22 kJ/mol

Jun 19, 1905

Two concentrates from Palabora, in South Africa, containing 0.056-0.068% undesirable Cu and 0.8 or 2.2% Ti, were chlorinated with air:chlorine ratios of 10:1, 15:1 and 20:1 at temperatures between 1 200 and 1 329 K. The resulting volatile chlorides were condensed and the solutions analysed for Cu, Fe and Ti. Recovery of Cu was less than 25% at low temperatures and short reaction times, but at 1 258 K almost all Cu was removed from the magnetite at all ratios of chlorine to air. At higher temperatures, the increased carrying over of iron as FeCl3 could be minimised by decreasing the partial pressure of chlorine. No titanium was detected in the volatile products and the percentage of Cu recovered was independent of Ti concentration in the concentrates, though as a function of Cl2 vol%, more Cu was recovered at 1 200 K from the low-Ti than from the high-Ti concentrate. In a fluidised-bed reactor, Cu recovery was 58-90% and iron carry-over less than 10 ppm

Jun 21, 1905

By E. Niehuis, J. Y. Kim, H. G. Cramer, S. L. Chryssoulis, K. G. Stowe, C. Bendel

TOF-SIMS was used to detect, identify from parent molecular ions and determine the relative concentrations of collectors sorbed on the surface of mineral particles in concentrate and tailings samples from three Canadian concentrators. In the Kidd Creek Zn circuit, sphalerite lost to tailings carried on average a quarter of the amount of isobutyl xanthate present on that recovered to Zn concentrate; amyl xanthate, which is not reported as added to the circuit, was also detected on floated sphalerite and pyrite. At Brunswick, sphalerite particles lost to the scavenger tailings had ten times less amyl xanthate and isobutyl xanthate than those recovered to the Zn final concentrate, while both xanthates were detected on sphalerite floated to the Cu-Pb cleaner circuit. At Matagami, significantly more isopropyl xanthate and isopropyl dithiophosphate were detected on sphalerite recovered to the final Zn concentrate than on that lost to the Zn rougher tailings

Dec 1, 1995

By S. G. Beattie, N. Mojtabai

A study was carried out which aimed to: determine the effects of blasting on excavation perimeters and nearby slopes; establish a low-cost blast monitoring and field observation programme to determine peak particle velocities and blast damage; and to develop criteria for observable blast damage that are based on the peak particle velocity. Full-scale production blasts in a large open pit copper mine were monitored and studied to develop damage criteria for various rock types. Better blast designs can be achieved by correlating the results of blast monitoring with field observations of damage at the pit walls and on benches. Back-break and damage are related to blast-induced ground vibration. Peak particle velocity is accepted as a reliable measure for the prediction of ground vibration levels. Empirical models for the estimation of rock damage can be developed and used for blast design. The models are used to determine the zones of damage within the rock face. Rock damage models can also be used to design trim shots to achieve further reduction of back-break in more critical areas

Apr 1, 1996

By R. J. Gochin, G. D. Schena, R. Spencer

The impact of a mineral project in a developing country is evaluated in the broad context of its economy using input-output models. Minimum economic theory is used to develop simple numerical models. Sets of technical coefficients are exploited in the development of linear models of the productive element of an economy. The analysis allows assessment of the overall economic consequences of a mineral development in which issues broader in scope than financial objectives need to be incorporated in the evaluation. In part 1, the framework for the development of the input-output model is presented. The model is refined to incorporate country-specific behaviour. The increased flexibility of the enhanced semi-input-output model permits a more confident investigation of the economy-wide effects associated with a new project in the mineral sector of a developing country. The relevance of the models is illustrated using an example from Namibia

Sep 1, 1991

By C. A. Pickles, J. M. Toguri

The refining of two molten Ag-Cu alloys, containing 7.5 and 11.2 mass% Cu, with a borosilicate slag was investigated using both air and pure O2 to determine the effects of the following variables: flow rate of oxidising gas; injection time; mass of sodium borosilicate flux; and injection of the oxidising gas into either the slag or the metal. The results demonstrate that more than 90% of the Cu can be removed with Ag losses of less than 5% and that refined metal with a Cu content of less than 0.5 mass% can be produced. Ag losses to the slag increased with the amount of Cu removed, and a mechanism is proposed to account for this

Dec 1, 1995

By Xuejing Xie, Tianxiang Ren

Paper presented at the 28th International Geological Congress held in Washington DC, July 1989 (International geochemical mapping sessions). Standardised stream-sediment sampling procedures have been used in mountainous and hilly terrains. Special sampling procedures were developed for application in remote environments, such as high mountains, desert, semi-desert, karst and loess-covered regions. The diversified analytical methods used in more than 20 analytical laboratories participating in the project have been unified into two multi-element, multi-method analytical systems. A unified data monitoring procedure was developed based on primary and secondary standard samples. To date the project has covered about 4 000 000 km2 and the aim is to complete the coverage within the present decade

May 1, 1991

Errors in ore reserve estimation can occur during drilling and sampling, sample preparation and analysis, geological logging and modelling, database construction, statistical or geostatistical evaluation, selection of economic parameters, selection of ore reserve method and assessment of mining constraints. Core sample recovery can be a major source of error, and it is proposed that the modelling of grade, metal accumulation and thickness should be accompanied by the modelling of core recovery (or core loss) so that for each ore block a weighted block recovery factor is obtained. This gives a good indicator of the reliability of a reserve estimate. It is suggested that a resource reliability rating (RRR) system be established to quantify what is meant by geological assurance and to combine this with an estimate of the precision of estimation as gained by geostatistical analysis. Proven and probable minable reserves would be those with an RRR better than 50% and a precision of estimation better than 20%

Dec 1, 1996

By H. K. Taylor

Ore reserves are inadequately defined. Geological reconnaissance and pre-feasibility mining work generate a broad range of valid tonnage estimates, many published for the benefit of various interests, who may view all figures as reserves. This work reviews the regular estimation of tonnages, grades and relevant factors for single deposits. A consistent framework of definition is suggested which, by conforming to the known structures of feasibility studies and long-range plans, avoids the pitfalls of over-categorisation and of unrealistic promises. Applications are based on North American experience but are intended for general use

Sep 1, 1991

The deposit was discovered during systematic reconstruction of the geological history of glacial overburden, which averages 6 m in thickness over 80% of Sweden, by geochemical sampling and searching for small grains of eroded bedrock. The gold is mainly concentrated in and around high-grade quartz veins within a broad shear zone, though the correlation coefficient between quartz and gold in samples is not significant. Production from two pits, now connected, in the Central and Eastern orebodies has increased steadily from 1 238 kg Au in 1989 to 2 120 kg in 1994, the highest in Europe. The mine has adapted and improved its mining methods to achieve significant productivity increases and cost reductions. Most of the improvements have been achieved through a better understanding of the controls on mineralisation and of the implications of those controls for selective mining. Geostatistics has played an important role in the quantification of grade variability and gold occurrence. Better blasting and loading techniques have improved selectivity, grade control has been enhanced by a grade-control drilling programme, and significant improvements in mineral processing have been made

Dec 1, 1995