Search Documents

By Richard Simon

This paper presents an ongoing study on the use of borehole breakouts to estimate in situ stresses at depth in a Canadian underground mine. Breakouts were identified using an acoustic televiewer (ATV) probe. Rock samples were tested in a laboratory to determine their failure curve. Breakout analyses were performed using a 2D failure criterion and a multiaxial failure criterion. Analyses were carried out using both short-term (peak) and long-term strengths (the latter considered here as being represented by the damage initiation threshold DIT). The analyses have shown that the use of the longterm strength and a multiaxial failure criterion leads to results that are more consistent with stress measurements performed in the field, in the vicinity of the mine.

Jun 1, 2012

By Kilmar Mine

The Kilmar dolomitic magnesite deposit~ in sourhwesr Quebec lie in Grenville Province sedimentary rocks that strike north and dip steeply west. The sediments comprise quartzitic, carbonate and argillaceous members. The middle or carbonate member hosts the magnesite and, like the two other members, has been intensely mewmorphosed. Magnesite occurs as lenticular shaped zones of altered limestone and is mixed with 5 to 30% dolomite crystals. Diopside, serpentine and mica are common accessory minerals. Magnesite appears to have formed from merasomarism of all or part of the carbonate member due to intrusion of hot magnesia-rich solutions. Magnesite is mined from a 490 m vertical shaf1 and is milled and burned into clinkers, which then are shipped 10 pyroprocessing industries around the world.

Jan 1, 1984

By G. M. Hutt

Introduction The major development of industrial minerals in Manitoba has been in building materials. 'The building-stone industry is developed far beyond the needs of the Province, and the well known Tyndall limestone is marketed over a wide area throughout the other provinces to Canada. Similarly, gypsum and gypsum products are produced in excess of local requirements and are exported to adjacent provinces. The crushed-stone, sand and gravel, limestone, and lime industries are sufficiently developed to supply the needs of the Province and, notably in the case of lime and lime-stone, there is a surplus for export to the adjacent provinces and to the United States. The manufacture of common brick is well established, but for face-brick and other clay products the Province is dependent largely on importations. Production of silica-sand will increase as Canadian markets become available through recognition of the utility value of the Black Island sand as foundry-sand and for other purposes. There is some possibility of the export of feldspar, of lithium ore and concentrates, and perhaps of salt. A considerable part of the Province has not been seriously prospected for industrial minerals and it may be expected that, as time goes on, other deposits of non-metallic minerals will be discovered and opened up, especially as the prairie provinces become more industrialized. At the present time, there is some activity in the southern part of the Province based on gas and oil indications. Whatever may be the outcome of this work, it should yield valuable information concerning the geological structure of the area.

Jan 1, 1934

By A. Warczok, C. M. Diaz, A. Bergman, T. Utigard, M. Barati

The world wide consumption of energy is steadily increasing and by 2030 it is forecasted to grow by another 50%, leading to mounting political and economic pressures. For any pyrometallurgical operation, it is therefore paramount to investigate and implement methods to decrease the use of energy. In the pyrometallurgical processing of steel, copper, nickel and other high temperature metals, a large amount of energy is lost in hot off-gases, molten slags, mattes and molten metals. Most of this energy is generally lost during the cooling and solidification steps with very little focus on energy recovery or reuse. In this paper we will quantify how much energy is contained in the various slag streams, then review previous attempts and methods employed to recover some of this energy, and finally evaluate some novel technologies that could potentially be employed.

Jan 1, 2011

By Z. Yang, M. J. Collins, N. E. Tuffrey, R. J. Kalanchey, I. M. Masters

The high elevation of China Western Mining Company (WMC)' s Ganhe refinery, and the high iron content of concentrates produced by the WMC mines, were key factors in the selection of pressure leaching by WMC for their new zinc refinery. This paper describes the results of pressure leaching test work conducted by Sherritt in Fort Saskatchewan with a sample of WMC concentrate from Qinghai Province in China. Results from batch pressure leach tests and a four-day pilot plant campaign are reported. The pilot plant campaign included continuous operation of a two-stage pressure leach circuit, as well as neutralization and iron removal steps, resulting in the production of iron-free zinc sulphate solution. Greater than 98% zinc extraction was achieved in pressure leaching, while producing solution containing about 9 g/L H2SO4 and 2 g/L Fe. Following neutralization and iron removal, the solution contained about 170 g/L Zn and less than 10 mg/L Fe. Overall recovery of sulphur in the zinc concentrate feed to elemental sulphur byproduct was about 85%, while 75 to 80% of the indium in the feed was recoverable from the neutralization residue. The test results highlighted the technical and economic advantages offered by the Sherritt Zinc Pressure Leach Process and provided the required data for the engineering design.

Jan 1, 2008

By C. Edwards

ABSTRACT: Milling operations in northern Saskatchewan’s Athabasca Basin have produced uranium continuously since 1975. During that period, the Athabasca Basin has been one of the world’s premier uranium camps, yielding more than 660 million lb (299,370,964 kg) of U3O8. In this paper, the author describes former and current milling operations and discusses why and how the milling process has changed and developed over the past 35 years. The author’s considerations for the future of uranium extraction in the Athabasca Basin conclude the paper.

Jan 1, 2012

By Bird. M.

As the Cadia mill was the first 40ft diameter SAG mill, commissioned in 1998, its performance, liner and discharge design attracted considerable international attention. Twelve years on, the liner design and the control philosophy are being readdressed to further improve the mill?s performance. A comprehensive series of 3D liner scans, over life of the liner, have been used to calibrate liner mass loss and progressive changes in the liner profile. This data is being used to provide true charge mass and mill filling, plus progressive trajectory profiles over life of liner. This information, along with measures of mill performance over liner life, is being used to select the optimal operating conditions as the liner wears, and hopes to inform future liner design.

Jan 1, 2012

By Gheorghe Marin, Franco Chiesa, David Levasseur, Bernard Duchesne

Over the past 20 years, pressure die casting has evolved to a point where structural parts can now be produced by this process. This has been made possible by the development of vacuum die casting and by the development of die-castable, low iron content alloys. This resulted in the production of low porosity, weldable die-cast parts on which heat treatment may be applied. In the present paper, the influence porosities on the tensile properties of as-cast A360 tensile test bars was evaluated. This was done by casting 24 clusters, comprising three 6mm diameter test bars each, in a 280T cold chamber pressure die casting machine after a steady dynamic equilibrium had been reached. Modeling of filling allowed to explain the differences in porosity observed in the 3 samples of a same cluster while the results of solidification modeling were related to the microstructure. Tensile samples were radiographed on a real time X-cube apparatus and separated into 2 lots: samples where no porosity defect were visible and samples with visible defects. By measuring the tensile properties of the 2 lots it was possible to quantify the drop in tensile properties brought about by porosity, which is the most common defect observed in pressure die-cast parts.

Jan 1, 2015

By C. Matthews, A. Vo

"Australia is one of the world’s leading exporters of bulk commodities and the extensive use of sampling equipment is key to the successful management of each mining operation. At the process plant, without a full understanding of the feed, product and tails, it is impossible to fully optimise the performance of the plant, such that the metallurgical balance is often open to error. At the port, a statistically correct, bias free and compliant sampling system is crucial to ensuring exported minerals are reflective of their true value and to avoid penalties. Over the last decade, as a result of the iron ore boom, there has been high demand for reliable, representative and standard compliant solids sample systems in Australia. This paper reviews several solids sampling applications at Australian mine sites, the challenges and experience gained and how the implementation of reliable representative sampling systems has provided better understanding of plant process performance, improved plant control and overall benefits to the operations.INTRODUCTION Mining is the primary contributor to the Australian economy with Australia ranking in the top 4 in economic resources for 21 primary industrial minerals in 2016 (Britt, et al., 2017). Australia is one of the world leaders in the export of the majority of its commodities including gold, copper and iron ore (Britt, et al., 2017). Therefore, a suitable and standard compliant sampling system is essential for evaluating plant performance and content verification. At the mine and at the port, the larger iron ore miners in Australia have developed stockpile models to predict the grade of their ore down to individual blocks of the stockpile. This allows the miner to create the right blend of material for sale to their customers and ensures they are not underselling their product or at risk of penalties for impurities or low grade. As an example, the average difference between the benchmark 62% Fe and low grade 58% Fe fines at the time of this report averaged US $30/tonne according to the Metal Bulletin Iron Ore Index. At a shipload of 180kt this would be a variation of US $5.4M. Whilst this is an extreme example, it highlights the economic importance of producing the correct grade product and a recognised representative sample of said product."

Jan 1, 2019

By S. Noh, T. K. Kim, B. O. Lee

Future nuclear reactor systems such as a sodium-cooled fast reactor are being designed under severe conditions in terms of operating temperature and irradiation fluence compared to current commercial reactors. For realization of such systems, it is necessary to develop an advanced structural material having both high strength and irradiation resistance at high temperatures. Oxide dispersion strengthened (ODS) steel is considered as one of the most promising structural material because of its excellent creep and irradiation resistance on the basis of uniformly distributed nano-oxide particles with a high density. Up to now, ODS steels have been intensively studied and developed to apply these materials to the in-core structural component of future nuclear systems. Several advanced ODS steels were designed and fabricated by a mechanical alloying, hot isostatic pressing and hot extrusion processes. This study focuses on the effects of heat treatment parameters during the fabrication process parameters on the microstructures of ODS steels for future nuclear system applications.

Jan 1, 2015

By M. S. Badollet

"DURING the past five years, production of asbestos fibers has increased in all countries that list asbestos as one of their mineral resources. Despite the many small mines that have been opened in Canada, United States, Mexico, South America, Italy, South Africa, Australia, Yugoslavia, and Rhodesia, the supply still does not meet the demand. It is estimated that total 1952 world production of asbestos fibers of all varieties approximated 1,600,000 tons, with Canada supplying 966,382 tons (I), or 60 per cent of all fiber mined.Asbestos fiber brokers continually are offering odd-lot samples of chrysotile, amosite, crocidolite, tremolite, and anthophyllite fibers to manufacturers, •quoting fantastic prices for tonnages •varying from just a few to 50 or more in a month. In many cases, the samples are not properly graded and contain quantities of rock impurities and finely ground dust.When vendors submit samples of asbestos fibers, the manufacturer should consider• them in terms of price, quality, quantity, and as possible substitutes for fibers currently used in his products.Grading of these odd-lot fibers in most cases has been poorly done, with resultant non-uniform fiber lengths. In some instances, a number of miscellaneous lots of fibers have been .blended for sale. This blending produces a fiber that is difficult for the manufacturer to accept as a substitute for the well-standardized Canadian fibers."

Jan 1, 1953

By A. J. Stapleton

"The Copper Mountain mine of Gaspe Copper Mines, Limited was brought into production in January, 1968.This paper describes the organization, scheduling and control of maintenance of large open-pit equipment, including 8-cu.yd shovels and 85-ton electric-wheel haulage units. The facilities for repair as well as maintenance are also described, including repair shops and field repair equipment. Maintenance costs are discussed and particular reference is made to tire inspection, records and costs."

Jan 1, 1969

By Frederic Benard

THE Ontario Refining Company, Limited, wholly-owned subsidiary of The International Nickel Company of Canada, refines the entire blister copper output of the latter's Copper Cliff smelter. Prior to 1936, the blister was cast in 460-lb. cakes at the smelter, loaded on open cars, and transported by rail to the refinery, a distance of approximately 1 1/4 miles. Here the cakes were transferred to the plant narrow-gauge system, charged to furnaces, and re-melted. This procedure necessitated the operation of holding furnaces and casting machines at the smelter -extensive re-handling-and melting down of a cold charge at the refinery. Transfer of the copper in molten form direct from converters to anode furnaces promised a considerable reduction in costs, and this possibility was investigated. As a result, a portable holding furnace, or hot-metal car, was designed and constructed. It was placed in operation in July, 1936, to be followed a year later by three additional units of slightly modified design. Figure 1 shows the original car, and Figure 2 the lacer type. With four cars in service, operations were placed on an all 'hot-metal' basis.

Jan 1, 1938

By C. W. Davis

AN inclined shaft is usually more difficult to sink than a vertical shaft, yet it is often chosen because of the subsequent saving in cross-cuts required to reach an inclined ore body. This paper briefly discusses the factors which led to the choice of an incline and then describes the operations involved in the preparatory work and in the sinking. These operations included a programme of mining out the underground facilities and installing the structures required for a hoist-room, cable-raise, waste-pass, ore pass, two sets of skip dumps, and a collar station equipped with counterbalanced drop-rails. The shaft was sunk 1,000 feet and four stations were cut, each with loading pockets. As the sinking progressed, the rock changed from hard porphyries and dense cherts to blocky limestones and earthy rubble. These conditions called for a change in methods and it is to the red it of the shaft-sinking crew that they overcame the new difficulties as the shaft progressed, while maintaining a satisfactory monthly advance. The section mined out was nine feet six inches by seventeen feet overall. This gave room for three compartments: two skip compartments four feet three inches by five feet nine inches inside the timber, to handle two-ton skips, and a manway three feet six inches by five feet nine inches. The sinking began on December 16th, 1941, and was completed on February 15th, 1943.

Jan 1, 1945

By V. C. Pandolfelli, L. Paulino, C. E. Zangiacomi

The continuous improvement in aluminum industry over the last years has increased metal output at lower cost. The potlining plays an important role in this regard due to high cost involved and more recently in its environmental aspects. In order to increase potlife and thus minimize the aluminum cash cost, a systemic approach is needed, through investigating the main cathode failure mechanisms by using a pot autopsy as a powerful tool, and then making the necessary chances to achieve extended potlife. In addition, preheating and pot start-up may also damage the cathode if not performed with an appropriate technique or even if the lining materials are not specified correctly, among other factors. All these aspects will be presented and discussed in this paper. Increased potlife, especially now that the current is reaching values up to 300kA, will allow aluminum plants to match their goals more efficiently at lower costs.

Jan 1, 2006

By James Mackie

The Vancouver Stock Exchange (VSE) has been providing venture capital for start-up companies since 1907. Ninety years' experience in the junior mining industry has enabled the VSE to develop policies and procedures tailored to the unique needs of start-up companies. Policies and procedures applicable to listed companies are documented in the Corporate Finance Services Department "Policy and Procedures Manual." Approximately 50% of the companies listed on the VSE are in the mineral exploration and development business. The largest number are exploring base metal, precious metal or diamond properties. A recent count shows that about 20 companies are exploring industrial mineral or non-metallic deposits. The minerals sought by these companies include limestone, decorative stone, building stone, lava rock, wollastonite, zeolite, garnet and graphite. There are two basic routes to obtaining VSE financing for an industrial mineral property. The owner can either sell an interest in the property to a listed company or form a company and have it listed on the VSE. In each instance, the listed company is responsible for raising funds to develop the property. A typical financing consists of the sale of company securities byway ofeitherprivate placement or prospectus offering.

Jan 1, 2001

By R. Agius, A. Nacu

"Cyanide destruction technologies are implemented at gold and silver operations to comply with the International Cyanide Management Code and meet ever more stringent discharge limits. Currently, the most common chemical cyanide destruction processes used in industry are sulfur dioxide/oxygen, hydrogen peroxide, and Caro’s acid. The cyanide destruction process used at an operation must reliably generate streams of acceptable quality at all times, and depends on numerous factors, including permit discharge requirements, tailings chemistry, location, site-specific climatic conditions and size of the operation. Selecting the most appropriate cyanide destruction process and determining the process design criteria requires accurate laboratory testing. This paper presents and discusses the results of a number of cyanide destruction evaluations that have been conducted to reduce cyanide concentration in process solutions or cyanidation tails. Laboratory testing provides important insights into reagent consumption and other factors required to achieve the target residual weak acid dissociable cyanide (CNWAD) levels.INTRODUCTION Process solutions associated with the extraction of gold and silver contain several forms of cyanide. The most toxic form of cyanide is free cyanide, which can be present as a dissociated cyanide anion (CN-) or gaseous or aqueous HCN. Weak or moderately stable cyanide complexes such as those of zinc, copper and nickel are classified as weak acid dissociable (CNWAD). Although less toxic than free cyanide, weak acid dissociable cyanide complexes are considered “ecologically sensitive” forms of cyanide and are regulated in most jurisdictions. In practice, reported WAD cyanide values comprises both free cyanide and weak acid dissociable cyanide complexes. Cyanide complexes with gold, mercury, cobalt and iron are referred to as strong acid dissociable complexes (CNSAD) and are much more stable, even under mildly acidic conditions. Another term commonly used in cyanide chemistry is total cyanide, which represents all cyanide compounds present in solution. Total cyanide levels in solutions are always equal to or higher than WAD cyanide values and the difference between the two usually indicates the presence of iron-cyanide compounds. Typically in Canada, CNTOTAL levels cannot exceed 1 mg/L in solutions discharged to the environment."

Jan 1, 2017

By Chris Twigge-Molecey, John Peacey

To meet the business objectives of a metallurgical project, there is often a need for new and untried technology or equipment, whose very novelty can present serious risks to meeting those objectives. The key risk management approach is a rigorous stepwise progression from theoretical evaluations and laboratory tests to pilot plant trials. These must be followed by demonstration-scale trials before final construction of a commercial scale plant, paying particular attention to the magnitude of the scale-up between phases. Success depends on following a well-defined program, not eliminating any steps, and ensuring adequate resources are available to the development team. Chapter 6 discusses the nature of technology risks to metallurgical plant projects, and the rigorous management practices needed to identify, analyze, evaluate, and avoid or mitigate them.

Jan 1, 2015

Mineral resource development activities impact the health and well-being of many people, from workers, to families and surrounding communities. In the decade up to 2010, mining revenues increased from 6% to 14% of Australian GDP, and minerals contributed 55% of total exports, with a growth in mining employment from 1% to 1.7% of the national workforce (Connolly and Orsmund, 2011). The growth in Australia?s minerals operations is mostly located in remote areas, or in rural communities with a limited population. As a result, operations have increasingly implemented long distance commuting (LDC) programs, often called ?fly-in, fly-out? (FIFO) and ?drive-in, drive-out? (DIDO), as a staffing strategy to meet rapid industry growth in locations with limited local populations. The rapid expansion of the minerals industry has resulted in considerable public debate about the benefits and costs to all sectors of Australian society. In response to the concerns of constituencies from many parts of Australia, the Minister for Regional Australia, Regional Development and Local Government, The Hon Simon Crean MP, asked the House Standing Committee on Regional Australia on Tuesday 23 August 2011 to inquire into and report on the use of ?fly-in, fly-out? (FIFO) and ?drive-in, drive-out? (DIDO) workforce practices in Regional Australia. The recently published report highlights the national interest and the diverse opinions about this practice in Australia. Resource extraction companies have developed several options to meet the accommodation requirements of their long distance commuting workforce. In this paper, initial results are reported from an ongoing survey of FIFO (and other non-residential) resource industry workers (n = 286) in the Australian resource extraction industries. The purpose of this study was to better understand how accommodation arrangements may impact on the health, wellbeing and job satisfaction of non-resident workers; and to attempt to find a relationship between different accommodation variables and workforce wellbeing and retention. In doing this it investigates evidence for the linkage between accommodation factors, hours of work, health, well-being, job satisfaction and job retention in the LDC work force.

Aug 1, 2013

Pillars are used in various forms in underground mining. For several decades pillar design has been an issue in both soft and hard rock underground mining. The major use of pillars is in room-and-pillar type mining. Pillars are critical structures in the production levels of block cave mines. With most mines leaning towards the use of block caving for ore extraction today, pillar design has become even more important. Empirical pillar design is popular. The use of numerical modeling is becoming more common in the design of underground mine pillars. A critical review of both the empirical and numerical modeling approaches to the design of underground mine pillars reveal some fundamental flaws. In general, pillar design approaches often assume the pillars are vertical, and are subjected to pure compression. Pillar failure criteria are then based on this assumption. Most papers on numerical modeling for pillar stability assessment use vertical pillars. This paper shows that where pillars are not subjected to pure compression the empirical pillar design approaches are inadequate, and that when using numerical models for the assessment of pillar performance, more care is needed in the determination of the average pillar stresses. The practice of relating field scale pillar strength to laboratory scale intact rock strength determined from conventional laboratory compression tests in empirical design equations is misleading when pillars are inclined or subjected to compressive and shear stresses. New data is added to the hard rock empirical pillar stability chart, and it is shown that it is misleading to conclude that failure of pillars with width to height ratios greater than 2.3 should not be anticipated. New empirical pillar design charts are presented for pillars at various degrees of inclination for different ko-ratios.

Aug 1, 2013