Search Documents

By Claude Bazin

"Laboratory semi-batch flotation tests were conducted using two different sulphide ore samples. The size reduction was adjusted to cover a wide range of flotation feed size distributions. Results show that similar recoveries can be achieved independently of the fineness of grind. This result suggests that possible energy savings could be achieved by a redistribution of the power between the grinding and regrinding mills. The behaviour of the selectivity curves shows that some gangue minerals are more sensitive to particle size than other ones, implying the existence of preferential associations between minerals in the ore.INTRODUCTIONInteractions between grinding and flotation have been studied for many years, and still a robust model to link the two processes lacks to be developed (Girard et al., 2005; Bazin et al., 2001). The ore size reduction liberates mineral grains, while flotation separates them into valuable minerals and gangue. The more size reduction that is applied to the ore the more important is the mineral liberation but also the production of fine particles that can pose problems during flotation (Trahar and Warren, 1976). The definition of the grinding requirement for flotation is a complex problem (Rickelton and Dell, 1977; Sosa Blanca et al., 2000; Morrison, 1993; Wei and Gay, 1999).This paper analyzes the effect of the fineness of grind using semi-batch flotation test results. The first two sections describe the test procedure and the results. The third section analyzes the results in terms of liberation and selectivity, and proposes a possible redistribution of power between grinding and regrinding mills."

Jan 1, 2006

By R. E. Michelutti

"The Sudbury area environment became drastically altered commencing in 1871 with lumbering, repeated fires and early open roasting operations from 1887 to 1929. These combined factors had such a pronounced effect that approximately 24 square miles were totally denuded of any vegetation and 87 square miles were semi-barren to somewhat stressed.The two nickel producing companies in the area have reduced the sulphur dioxide emissions considerably over the years. Falconbridge Limited, alone, reduced sulphur dioxide emissions by 77% from 1971 to 1984.These reductions have resulted in improvements to the air, soil, lake and vegetation quality in the Sudbury area.INTRODUCTIONThe Sudbury area environment became drastically altered commencing in the 1870's with lumbering, repeated fires and early open roasting operations from 1888 to 1929. These combined factors had such a pronounced effect on the Sudbury environment that approximately 24 square miles (64 sq. km.) were totally denuded of any vegetation and 87 square miles (225 sq. km.) were semi-barren.Over the years, the Sudbury area environment has improved considerably. This has been due to emission cutbacks by both Inco Metals and Falconbridge Limited, coupled with industry, government and community reclamation programs. Before the improvements are discussed, a better understanding of the historical degradation is required."

Jan 1, 1986

By P. Hickey

"The object of this paper is to describe how the Iron Ore Company of Canada develops its management personnel. It will elaborate on the practical application of Supervisory Training and Management Development.Why are Supervisory Training and Management Development important? The answer has been the subject of many textbooks. Dr. Ken Blanchard, author and consultant, addressed this issue concisely when he said that effective managers and organizations must do two things, ""get results and develop people"". lPeople development at IOC is best illustrated through its supervisory training and management development programs. For the past twenty-five years IOC has been recognized as an industry leader in the training field. Periodic studies have played their role in establishing and maintaining this distinction. For example, in 1974, the company decided to review and up-date all its training programs. At this time, it established its own Task Force on Training and this resulted in the development of many of our present programs. Today, Supervisory Training (i.e. for first and second level management) at the Carol Project in the Labrador City area consists of various programs including: New Foreman Induction, Foreman Entrance School, Basic Management Skills, Management II, and Effective Presentations."

Jan 1, 1983

By D. M. Fraser

"Brunswick Mining and Smelting Corporation Limited operates two mines; one open pit (No. 6) and one underground (No. 12), approximately 20 miles south-west of Bathurst, New Brunswick. Both are massive sulphide deposits containing copper, lead, zinc and silver. The No. 12 property began operation in 1963 and is presently being mined at a rate of 3600 tons per day underground and is in the completion stages of an expansion to achieve 11,000 tons per day underground by the end of 1930.Originally at Brunswick Mining, acid mine drainage was added to tailings and neutralized by an excess of lime in the tailings. A conventional recycle system was established with a biostabilization pond for the treatment of thiosalts, a liming station and sludge settling area for neutralization of acidic water and a final reclaim pond with a pumping station for reclaim water.We found that not more than one third of the reclaim water could be used as it upset the flotation circuit every time it was used. It was established that the mine water and surface drainage were the cause due to oils and detergents in the water. It was also found that the biostabilization pond method Cf thiosalt treatment was not efficient for year round operation in our climate.In 1974, we reviewed the problems and began a 3 phase program to control effluents from the property:"

Jan 1, 1980

"A simple approach to optimizing the performance of an operating carbon in pulp (CIP) or carbon in leach (CIL) plant is presented. It is possible to reproduce the performance of an operating CIP or CIL plant in the laboratory, in small scale batch tests in which the rates of gold leaching and carbon adsorption are determined, coupled with mathematical models that translate the batch kinetic data into predicted steady state profiles of gold in solution and on the carbon across multi-stage adsorption circuits.Once the performance of the commercial plant has been mimicked by the model, the plant operating parameters can be varied systematically in the model, and the likely response of the plant to the stepwise change can be determined. In this way it is possible to inexpensively optimize the design of both greenfields CIP or CIL circuits and plant expansions, or optimize the operating parameters of an existing plant, with no disruption to plant operations and no economic risk to the mining company.This approach has been adopted by IAMGOLD Corporation, to the immediate benefit of two of their existing gold operations. The methodology adopted and the results achieved are presented.INTRODUCTIONThe carbon in pulp (CIP) and carbon in leach (CIL) processes became firmly established in the gold mining industry in the 1980s, initially in South Africa and Australia, from where they spread rapidly to all the gold producing regions of the world. The percentage of annual global gold production by activated carbon-based processes grew from zero in the 1970s to almost 70% by the turn of the century, which represented a phenomenal rate of acceptance of a new technology by a traditionally conservative industry. The main reason for this rapid acceptance of the new technology was the fact that the first few large plants built in South Africa convincingly demonstrated better gold recoveries than the traditional filtration/Merrill Crowe process, with lower capital and operating costs. And as the plants developed an operating track record over their first few years of life, they proved to be remarkably robust mechanically, and highly tolerant of plant upsets, changes in feed composition and solution phase contaminants that had caused problems in Merrill Crowe plants."

Jan 1, 2011

By David Meadows, John Starkey

"As part of the ongoing project development for the Tenke Fungurume Copper-Cobalt Project in the Democratic Republic of Congo, Phelps Dodge Corporation has examined methodologies for determining the size of grinding mills to support a 7000 mtpd operation. Six samples were tested by Hazen Research, Inc. (HRI) to obtain the JK parameters using the JK Drop Weight Test, standard Bond crushing, and rod mill work indices, abrasion indices and by Dawson for Bond Ball Mill Work Index tests using crushed feed, and Standard Autogenous Grinding Design (SAGDesign) Tests, patented by Outokumpu. (See reference 8 below).The comparison of these results gives context to how the various measurements relate to each other and how they can be used to obtain an accurate design for the grinding mills required for the Tenke Project. This is the first published direct comparison between JK Drop Weight, standard bond work indices, and SAGDesign test results. The SAGDesign test includes a SAG test followed by a Bond BM Wi test done on SAG ground material.INTRODUCTIONAfter the presentation of the paper “SAGDesign Testing – What It Is and Why It Works” at the recently concluded SAG 2006 Conference in Vancouver, a question was asked about how SAGDesign ore hardness measurements compared with other comminution tests, specifically the JK Drop Weight Test and the parameters that are derived from such testing. At that time it was noted that a paper was being prepared for the CMP Conference in January to show how various ore hardness measurements compare with each other when done on the same samples.This paper will therefore present the first such comparison using test results from the Phelps Dodge Tenke Fungurume Project where six composite samples were examined by the tests noted below. A seventh sample was tested at Dawson but not at other labs. The tests were done at four different laboratories listed below and included the tests shown."

Jan 1, 2007

By J. A. King, D. A. Knight

"The Porgera orebody is located in mountainous terrain in Enga Province, Papua New Guinea. An underground mine has been developed which produces up to 2000 t/d of ore grading over 2 ozs Au/t. Some 79% of the gold in the ore is free, with the balance in a highly refractory form as sub-microscopic gold evenly disseminated within a pyrite matrix.This paper describes the metallurgical plant that uses flotation and cyanidation circuits to effectively recover the free gold in the ore feed, allowing for wide variation in the gold head grade. The refractory gold component in the ore is stored as leached pyrite flotation concentrate and this concentrate will be later treated by autoclaving techniques to recover the contained gold.The ProiectThe property is located in the Porgera Valley 600 Km North West of Port Moresby. The remote location is 2500 m above sea level. The mine area has 3600 mm of annual rainfall and a temperate climate with temperatures ranging from 10° c to 22° c throughout the year.Alluvial gold was reported in the Porgera area in 1938 and has been an important source of revenue for the area for many years. Intermittent exploration was carried out until the 1960 1 s when Placer (PNG) Pty. Ltd. with Mt. Isa Mines commenced an extensive exploration program. The property was brought to production in 1990 by the Porgera Joint Venture group consisting of Mount Isa Mines Ltd, Rennison Goldfield Consolidated Ltd. and Placer Dome Inc, each with a 30% ownership and the Government of Papua New Guinea with a 10% share. Placer Dome Inc. is the manager of the property with construction under the direction of the Placer Dome Technical Services group."

Jan 1, 1992

By A. J. Hyett

Due to the ongoing revolution in electronics and communications more cost-effective geotechnical instruments can be manufactured using digital technology. This new generation of digital instruments have embedded microcontrollers that provide highly accurate and reliable measurement of geotechnical behaviour in real world units that can be immediately interpreted. Digital measurements can be transmitted across existing mine-wide wireless communication networks, interfaced directly with infra-red enabled PDA?s or PC?s, and parsed to memory by low-cost data-loggers.

Oct 1, 2004

By C. S. Maggs, L. Shwydiuk, H. W. Newcomen

The southwest wall of the Lornex Pit at the Highland Valley Copper mine has been experiencing slope displacements since 1978. Measures to manage the displacements on previous pushbacks have included stepping out, scheduling pushbacks to unload the crest of unstable areas, slope dewatering and mining with intensive slope monitoring. The final pushback on this wall is currently being mined and substantial modifications to the slope geometry could prove to be uneconomical. As a result, a campaign of surface water collection and diversion, horizontal drainhole drilling and deep well drilling is currently underway to maintain an acceptable degree of stability to the end of mine life. The various factors contributing to instability, including engineering geologic controls, rock mass strength, and surface and groundwater hydrology are presented. Movement trends, displacement magnitudes and stability analyses results are also discussed.

Jan 1, 2003

By A. Coulombe

"RésuméL’analyse des séquences d’exploitation, actuellement en usage pour les gisements très inclinés, a démontré qu’elles ne sont pas toujours optimales du point de vue du contrôle des terrains et de la concentration des travaux d’abattage (nombre de chantiers simultanément en opération). Effectivement plusieurs séquences sont très propices à la création des nombreuses zones de hautes contraintes, qui sont à l’origine des effets de pilier. L’étude de cas de la mine Lac Shortt a démontré que certaines séquences d’exploitation, actuellement en usage, ne sont surtout pas adéquates dans le cas d’un état élevé des contraintes naturelles. En effet la mine a eu de sérieuses problèmes avec le contrôle des terrains (coups de terrains et les effondrements des épontes). Ces effondrements étaient responsables de la dilution excessive et des pertes importantes des réserves minières. Les deux nouvelles séquences proposées, visent la meilleure redistribution des contraintes d’exploitation en vue d’éliminer la création des effets de pilier. En plus elles permettent une concentration plus élevée des travaux d’abattage.À notre avis les séquences proposées pourraient améliorer substantiellement la stabilité des chantiers d’abattage et par la suite les performances technique et économique des opérations souterraines. ABSTRACTThe planning of underground mining sequences represents an important aspect of the mining operation. The analysis of mining sequences actually in use for very steep orebodies has demonstrated that they are not always optimal, considering ground control and the number of stopes simultaneously in extraction. These sequences are conducive to the creation in the rockmass of several stressed zones caused by pillar effects. The case study of Lac Shortt mine showed that the sequences of exploitation currently in use are not adequate especially in the case of a high state of the natural constraints. Indeed, the mine had serious problems with ground control (rock bursts and collapse of walls). These collapses were responsible for excessive dilution and significant losses of mining reserves. The two new sequences suggested aim for the best redistribution of exploitation constraints in order to eliminate creation of pillar effects. Moreover, they allow a higher number of stopes to be extracted simultaneously. In the opinion of the authors, the sequences suggested could substantially improve the stability of working areas and, thereafter, technical and economical performances of the underground operations."

Jan 1, 1998

By Michel Ruel

"PID loops – also known as base layers or regulatory controls – form the foundation of any plant’s control layer and it is generally accepted that PID loop health has a direct impact on the plant’s bottom line. Keeping these thousands of control loops in good health has a direct impact on the plant’s bottom line: it reduces variability, improves quality and throughput, and decreases energy costs and raw material usage. This has been well proven and documented in many articles. In the last ten years, technology has evolved: control engineers can now keep track of control loop performance and link it to the root causes of variability. However, they lack industry-wide best practices and criteria for determining what can be considered as excellent, good, fair, or poor performance. To ensure that PID control loops continue to perform well and meet their objectives, control engineers need a combination of (a) an appropriate monitoring technology and (b) best practices for doing the maintenance of base layer controls.Most plants have limited resources and operate with an increasing number of constraints; therefore, using the right tools and including reports in daily workflow is key for success. This paper suggests roles and responsibilities of key players needed to work toward control performance best practices and discuss organisational changes to succeed.INTRODUCTIONAlthough PID controllers are reliable workhorses in the process industry, they are often underrated. Since the 1980’s, computer control has evolved and the control algorithms used by control engineers have become increasingly complex. However, PID controllers still handle over 90% of the control loops in operating plants. Table 1 shows the savings that can be realized by achieving best-practice in several different process control categories (Brisk, 2004). The savings are expressed as a percentage of production costs."

Jan 1, 2011

By R. Dahlke, J. A. Finch

"A campaign was undertaken during the greater part of 2001 at Noranda’s Brunswick Mine Concentrator to investigate the role of gas (air) superficial rate distribution (Jg profile) to the cells in the final Zn cleaning stage (bank of seven cells). Three profiles were tested: Balanced (each cell with same Jg), Increasing (from cell 1 to 7), and Decreasing, along with an “as found” profile in a parallel control bank. The experimental design allowed for two confounding factors, changes in ore type and circulating load. The Increasing profile consistently gave the best metallurgy (down-the-bank grade / recovery). The reason for improved performance was traced to the response of the first few cells. The Increasing profile gave the highest selectivity of sphalerite against non-sulphide gangue (NSG) in these cells with relatively even recovery per cell down the bank (10-15% based on feed to each cell). The other profiles gave lower selectivity and higher zinc recovery in the first cells (up to 25% in cell 1), which combined to reduce overall bank performance. The increased selectivity with the Increasing profile is attributed to the low gas rate in the first cells reducing water recovery and hence limiting entrainment of NSG gangue. The Increasing profile was subsequently configured for all four stages in the zinc cleaner circuit.INTRODUCTIONThe performance of a flotation circuit is largely the result of the operator’s response to visual clues. This includes manipulation of the gas (air) input and how it is distributed to cells in a bank. A lack of sensors prescribes this approach. Over the past ten years the Mineral Processing Group at McGill University have developed a set of gas dispersion sensors including one to measure gas superficial rate (or simply “gas rate”), i.e., volumetric gas rate per unit cell crosssectional area, Jg (Gomez and Finch, 2002). The device collects bubbles in a tube immersed in the pulp and infers Jg from the pressure-time curve generated after a valve is closed and air starts to accumulate. The usual units are cm/s. It is robust, reliable and suited for plant use.A version of the Jg sensor was tested extensively during 2000 at Noranda’s Brunswick Mine Concentrator (Dahlke et al., 2001). The results were sufficiently encouraging that a sensor was fabricated to suit local requirements (Insta-Jg). The sensor detected malfunctioning field instruments and flotation mechanisms, and demonstrated that gas distribution to cells in a bank “as found” had no particular pattern, or profile. Preliminary testing suggested that a balanced profile (i.e., all cells with the same gas rate) gave superior metallurgy (grade / recovery down the bank) than the “as found” profile. This observation prompted a focused campaign to explore the impact of the gas rate (Jg) profile, introducing the notion of “gas distribution management”."

Jan 1, 2004

By G. D. West, J. D. Purdue

"Marked Ball Wear Testing (MBWT) employs identified grinding balls which are placed in an operating mill for a period of time, retrieved from the mill, and then measured to determine the amount of wear experienced. This is an excellent method to evaluate the relative differences in the wear rates of various grinding ball materials and/ or manufacturing process variables simultaneously and under actual production milling conditions. This paper outlines the methods of ball identification, testing and evaluation procedures and discusses the strengths, weaknesses, and proper application of marked Ball Wear Test results. INTRODUCTIONThe consumption of grinding media in the mineral processing industry represents a substantial cost to the comminution process. Grinding media is most often found to be the second highest consumable cost next to energy. To determine the selection of the most cost effective media, one must determine the specific wear mechanisms present in a given grinding application and decide which media system addresses these mechanisms most economically.A MBWT has definite advantages over other methods used to evaluate the relative consumption rates of grinding media. It allows the comparative testing of a large number of different ball types under identical operating conditions in a very short period of time. In addition, production wear rates can be accurately predicted directly from MBWT results. Typical MBWT test periods are in the order of 350 to 700 operating hours for high wear rate application and upwards of 2000 or 3000 hours for low wear rate applications. These times are much less than the 5000 or more hours required to purge a mill of the incumbent ball charge (to convert it to the test ball) and then provide even a minimal test period in which to conduct a full production test, for just one type of ball. Under production test conditions the evaluation of competitive product or the development of improved grinding balls is necessarily slow."

Jan 1, 1991

OVERVIEW OF PRESENTATION ? What is LMI ? Who uses LMI and how? ? Value of LMI to the Mining Industry ? Mining Industry Workforce Information Network (MIWIN) ? The Challenge: Forecasting the future in uncertain times ? Results: Hiring requirements in the next decade ? Results: Occupational information ? Next steps

May 1, 2009

By G. Winkel

Safety conditions in industry have greatly improved over time. However, around the world, in Canada, and in each province or territory, people are still the victims of serious industrial accidents. The increasing safety of people at work then continues to be an imperative in industry today.<p> So how do we achieve a workplace where no one gets hurt? Well, in simple terms, folks need to be protected from unplanned exposures to equipment or energy sources that can do harm. If you think about it, all of our efforts in loss management and safety should then be directed toward avoiding these uncontrolled events. And it works! Our safety performance over the years has enjoyed tremendous improvement due to this support for loss management and safety. We now explore best practices toward achieving that next step in safety improvement.<p> As shown following, a large combination of loss management activities act together to support safety performance. Many of these activities are interrelated and some people have described them as the ?inputs? into an approach or program for achieving safety. Using this description, it follows that the ?outputs? of the program are some of the advertised measures of safety we see around us today, such as injury frequency rates. <p> It is asserted that a leadership focus to regularly measure safety and loss management activites (so-called ?inputs?), as a basis for taking supportive actions to ensure their effectiveness, is the basis for safety results (so-called ?outputs?) that consistently achieve high standards of excellence.<p> The concept of managing input activities, as enabled by effective measurements, can significantly act to transform our focus and priorities in the workplace. Supporting input activities like strategies, plans, or procedures with our best efforts will get us to our intended goals. Tracking outputs alone will not.<p> Safety and production have traditionally been cast as competing objectives. When both objectives are mutually supported and considered, however, people will invent ways of doing work that support both safety and production, and any other business parameter. When done right, innovation through meaningful involvement of affected people in the workplace will support safety excellence in a manner that in turn improves business efficiency overall.<p> For a workplace to be safe, it then requires everyone?s help and participation to make it happen, a collaborative effort by management, leaders, and frontline folks with the power and responsibility to take appropriate action at every level in the organization. In this way, everyone becomes a leader in safety.<p> The achievement of commitment to loss management input activities by folks in the workplace is the basis for attaining safety excellence. A workplace founded on commitment supports a safety culture with a vision for safe work performance at outstanding or world-class levels of achievement.<p> One may ask if injury incidents will be eliminated with this commitment and focus on workplace safety? Well, despite our best efforts in this area, there is never a guarantee that things can?t go wrong. We are simply not perfect. There remains in our workplace complexities and unanticipated risks that can have disastrous consequences if not managed at every moment. And when it goes wrong, we need to know we?ve truly tried our best, and now we have more to learn so we can get even better. <p> That?s the challenge represented by the safety imperative, a challenge to take safety performance that next step, a fulfillment of our commitment to the moral obligation we have to each other?s safety. It?s an effort that will continually raise the bar of world-class safety performance achievement for future generations. It?s a legacy we can be proud to be part of.

Sep 1, 2004

By G. Winkel

"Safety conditions in industry have greatly improved over time. However, around the world, in Canada, and in each province or territory, people are still the victims of serious industrial accidents. The increasing safety of people at work then continues to be an imperative in industry today. In addition to protecting people, safety has been shown to make good business sense in any industry.The road to safety improvement is built on establishing a culture of safety that forms the basis for how work gets done in a company. Most importantly, an effective safety culture is built on the full engagement and participation of workers and leaders alike, who share in a vision for safe work performance where “no one gets hurt” and “everyone is a leader in safety.”Let’s learn together on how we can make a safety culture happen. The resulting bias for safety will ultimately save lives, and fulfills our moral objective to strive for safety excellence. IntroductionWe have the good fortune of living in democratic countries where freedom and the value of human life are key beliefs. These beliefs translate into the moral obligations and laws that we value and uphold in our society and life today.A minesite or workplace is simply a necessary part of our society where people earn a living. It is a place where our moral obligations and laws equally apply, a place where human life is of ultimate importance and value. In the early years of industry, this value has not always been evident. Take this description of a tragic accident reported in a coal mine on December 8, 1879:“Oliver Thompson, shaftman, aged 35— While taking wooden partitions out of a ventilation shaft, he fell off the work platform a distance of 100 yards, there did not appear to be anything unusual to account for this accident.”"

Jan 1, 2004

By S. Banisi, H. R. Iran-Manesh, M. R. Shayestefar, H. Shekarchyan

"Flotation circuit of the Sarcheshmeh copper mine processes 41,000 t/d of ore at 0.9% Cu. Chalcopyrite and chalcocite are the main copper bearing minerals which are concentrated in three stages of roughing, cleaning and recleaning. Due to major changes in the reagent addition regime, make-up balls combination, and throughput to the primary mills an increase of 2.6% (from 87.2% to 89.8%) in the sulfide copper recovery was obtained during a period of six years. In order to investigate a rather large variation of monthly recovery (i.e., from 89.0 to 91.2%) of the plant after implementation of the changes, a study was undertaken to trace mineralogically possible causes of such a behavior. During a five-month period, monthly composite samples of feed and tailings of the flotation circuit were taken. At the first stage, the polished sample preparation method and the mineral counting procedure were optimized through a detailed study. Liberation degrees and types of locking of valuable minerals in both streams were determined in three size intervals of +75, +38 and –38 microns. It was found that for both recovery levels (i.e., 89% and 91.2%), there was no significant difference in the liberation degrees of valuable minerals in the flotation feed; the average liberation degree was 57.1% with a standard deviation of 3.1%. On the other hand, in the case of high recovery level (i.e., 91.2%) there was a reduction of 15% in the amount of free valuable minerals in the tailings stream. The highest reduction was found for the -38 micron size range in particular for chalcocite. It was concluded that compared to the grinding circuit the change in the flotation circuit had the significant effect on the plant recovery increase.INTRODUCTIONThe Sarcheshmeh copper ore body contains 1 billion tonnes averaging 0.90 % copper and 0.03 % molybdenum. It is located southeast of Iran and currently processes 41,000 t/d of ore. The concentrator has been in operation since 1982. Last year, the concentrator produced 130,000 tonnes of copper and 4,000 tonnes of molybednite concentrate. An expansion to the plant which will increase the throughput by 50% is under construction and will be effective in 2003.After three stages of crushing, the ore with a F80 of 12.7 mm is fed to 8 parallel ball mills in closed circuit with cyclones to produce a product 70% finer than 75 microns. The concentrate of the first stage of flotation is reground and the tailings constitute the main component of the plant final tailings. A concentrate with an average grade of 30.5% Cu is obtained after cleaning and re-cleaning stages. At the present time, the average sulfide copper recovery of the plant is 89.8% which varies depending on the operating conditions and ore type."

Jan 1, 2003

By E. J. Fuller, J. C. Monette

"Gold and silver cyanide complexes are presently desorbed from activated carbon by means of hot caustic elutions. These solutions may or may not contain additional sodium cyanide. There are several parameters which affect the rate of stripping. Some of these include pH, ionic strength, and temperature. (1) Stripping is conducted in recirculating (ZADRA) or once through (AARL) circuits.This paper describes the development of a new chemical eluant which significantly increases the rate of stripping of both gold and silver cyanide complexes from activated carbon. Two case history applications are also described.INTRODUCTIONAdditional cyanide is used in strip circuits in order to prevent its depletion which could lead to precipitation of base metals or lead to a change in the nature of the gold cyanide complex to one which does not strip as easily. (2)The strip circuits that are able to function efficiently without the use of cyanide are mostly those where the carbon is acid-cleaned after stripping.Once the minimum cyanide requirement to maintain the complexes in their proper state are fullfilled, any futher incremental increase in the level of cyanide will have no bearing on the rate of stripping. (3)DEVELOPMENT OF THE NEW ELUANTGeneral DiscussionVarious carboxylated materials were investigated including octanoic acid, polycarboxylic acid (various molecular weights), salicylic acid, polymaleic acid, acetic acid. benzoic acid, terephthalic acid, 4, bi-phenyl carboxylic acid, phosphoric acid and stearic acid.The initial work was done on medium activiiy, non acid-cleaned carbon. The silver to gold ratio on the carbon varied greatly.Two different blanks were used. The first was an elution using a 2% caustic and 0.4% cyanide solution while the second was a 2% caustic elution."

Jan 1, 1992

By Euler De Souza

Backfilling in Canadian mines has been practised for close to 100 years and evidence anticipates the application of mine fill technology at an increasing rate during the foreseeable future. The evolution of backfill technology is closely related to the advancement of modern mining methods and the development of new backfill technology continues to evolve. The authors, after conducting extensive surveys of backfill practices in underground mines across Canada, have concluded that, because backfill operations employ large quantities of cement and experience large costs associated both with backfilling practice and cement use, opportunities exist for reducing backfill energy costs and enhancing the application of alternative cementing agents in backfill. Consequently, the authors have developed an alternate, equally effective and lower cost binder agent replacement for cement, and incorporated waste glass into the development of a lower cost backfill (glassfill). This paper presents the results of two design stages associated with the development of glassfill: strength development and flow performance. The advancement of this technology has reached a stage that should promote industrial implementation within the Canadian mining industry. A number of Canadian mining operations exhibit potential for plant optimization through possible binder source replacement, and might thus realize associated reductions in backfill and energy costs.

Apr 1, 2005

By R. E. de Barrio, M. E. Lanfranchini, R. O. Etcheverry

"The El Abuelo Ca-Fe-magnetite skarn and related hydrothermal quartz veins are located at Cerro Pepita Hill, in southwestern Chubut province of southern Argentina, 1700 km southwest of Buenos Aires. These deposits are developed in a continental magmatic arc environment linked to the Andean orogeny. Iron skarn mineralization is mainly hosted by an Upper Jurassic to Early Cretaceous sedimentary sequence interbedded with Upper Jurassic basaltic andesite, and is spatially associated with Early Cretaceous calc-alkaline dikes. Ore grades vary between 40 and 63 wt.% Fe. In addition, anomalous metal contents (>10 000 ppm Cu and up to 81 g/t Ag) are present in the hydrothermal quartz veins.At least three paragenetic mineral assemblages have been identified in the El Abuelo exoskarn: (1) amphibole > epidote ± chlorite ± quartz, formed by isochemical contact metamorphism; (2) Fe-clinopyroxene ± Ca-garnet, formed during prograde metasomatic anhydrous exoskarn formation; and (3) actinolite ± epidote ± chlorite ± quartz ± magnetite > titanite, resulting from hydrous retrograde alteration of exoskarn. Endoskarn alteration involved an early Mg-Fe-clinopyroxene ± Fe-garnet assemblage followed by retrograde actinolite replacement of pyroxene. Lower temperature hydrothermal alteration related to quartz veins was superimposed on the skarn assemblages, showing an innermost sericite ± adularia ± pyrite ± chalcopyrite assemblage and an external propylitic halo.Some metallogenic characteristics of the mineralization and the geological setting resemble those in several iron oxide copper-gold deposits elsewhere in the world."

Jan 1, 2007