Search Documents

By M. Massinaei, S. Abasi, M. Oliazadeh

Reliable measurement and control of the pulp-froth interface (froth depth) in the flotation columns is critical to achieve the desired metallurgical performance. Shallow froths result in a reduction of grade because of particle entrainment and deep froths reduce recovery because of the drop back of entrained and weak hydrophobic particles to the pulp zone. The cleaner circuit at Miduk copper concentrator consists of three parallel MicrocelTM flotation columns 4 m in diameter and 12 m in height. The interface level of the flotation columns is measured by two pressure sensors located at 1.4 and 2.4 m from the cell lip (in the collection zone). In this study the performance of the level detection system at different operating conditions was evaluated. A calibrated float-ultrasonic location system was used for measuring the actual froth depth. The results indicated that the existing level control system was subject to considerable error. The absolute error was found to be 33.27 cm. This was mainly attributed to the constant set-point value assigned to the froth density (ρf=0.3 g/cm3), which actually varies with the operating conditions. The actual froth density at different conditions was calculated and its average value (ρf=0.12 g/cm3) was re-set in the control system. This resulted in substantial reduction in the level-detecting error. Recommendations for more accurate measurement of the interface level were presented. INTRODUCTION Froth flotation is a complicated process because of many involved variables. One of the most significant controlled variables in the flotation process is the pulp-froth interface (froth depth). The froth depth has a profound influence on the metallurgical performance parameters (i.e. grade and recovery). Shallow froths result in grade reduction because of particle entrainment and deep froths reduce recovery resulted from the drop back of entrained and weak hydrophobic particles to the pulp zone (Finch and Dobby, 1990). Various techniques have been developed for measuring the interface level of the flotation cells in the last few decades. These techniques can be classified as: Techniques based on hydrostatic pressure measurements (Finch & Dobby, 1990), Techniques based on the density gradient (float) (Moys & Finch, 1988), Techniques based on conductivity measurements (Uribe-Salas, 1991), Techniques based on temperature measurements (Moys & Finch, 1989).

Jan 1, 2019

By Dave Bulled, Chris Bennett, Glenn Kosick, Glenn Dobby

"Mining companies around the world are embracing geometallurgical modeling at a rapid rate, as senior executives realize that inputs must be properly measured if the output is to be managed effectively. Geometallurgical modeling is used to scientifically manage risk in project evaluation, for plant design and production forecasting, and optimization of production planning and mineral processing/metallurgical unit operations. The technology also provides a solid foundation for implementing broad corporate strategies with respect to intelligent asset utilization and metal sales. Over the past five years, MinnovEX Technologies Inc. has been actively engaged in developing, promoting and applying geometallurgical modeling technology for major mining companies around the world. This paper describes the methodology for successfully applying the technology for the unit operations of comminution and flotation in the mining industry.INTRODUCTIONGeometallurgical modeling (referred hereon as geomet modeling), in theory, can be applied to its full potential on all unit operations in mineral processing; however, this paper will concentrate on two of the largest unit operations, namely comminution and flotation, where the technology is actually being practiced by many large mining companies. For concept studies and prefeasibility studies, aspects of geometallurgical technology are regularly applied but in a less rigorous manner than for final feasibility studies where justification for funds is sought. This paper will focus on the final feasibility stage of a project and on existing operations or planned expansions, where the full power of geometallurgical technology is brought to bear in a cost effective manner.One of the unique aspects of geomet modeling, when used to its potential, is the ability to design plants, and forecast and plan production with a quantifiable degree of precision, something that was unattainable in the past. This means that when new comminution and flotation plants are designed, the mining companies and financial institutions involved in the project can measure the precision of the design and therefore better understand and manage project risk. It means that for existing and new operations, metal sales personnel can carry out their sales strategies with a much better understanding of the degree of error associated with production forecasts of concentrate/metal and quality of concentrates. For mine and mill managers, geomet modeling allows the effect of the mine plan on the downstream processes to be quantified; thereby allowing the mine plan to be recast in a more optimized manner. Finally, existing concentrator personnel can optimize their unit operations based on a more definitive understanding"

Jan 1, 2004

By James D. Bittner

Separation Technologies, LLC (ST) has developed a processing system based on triboelectric charging and electrostatic separation that provides the mineral processing industry a means to beneficiate fine materials with an entirely dry technology. The environmentally friendly process can eliminate wet processing and required drying of the final material. The process requires little if any pre-treatment of the material other than grinding and operates at high capacity ? up to 45 tonnes per hour by a compact machine. Energy consumption is low, approximately 1 kWh/tonnes of material processed. Since the only potential emission of the process is dust, permitting is typically relatively easy. In contrast to the other available electrostatic separation processes that are typically limited to particles greater than 75 µm in size, the ST belt separator is ideally suited for separation of very fine (<1 µm) to moderately coarse (500 µm) materials with very high throughputs. The triboelectric particle charging is effective for a wide range of materials and only requires particle ? particle contact. The small gap, high electric field, counter current flow, vigorous particle-particle agitation and self-cleaning action of the belt on the electrodes are the critical features of the ST separator. The high efficiency multi-stage separation through charging / recharging and internal recycle results in far superior separations and is effective on fine materials that cannot be separated at all by the conventional electrostatic techniques. Since 1995, this triboelectric process has been extensively used for the beneficiation of coal fly ash with eighteen separators in place and over 100 machine-years of operation at locations in the US and Europe. The technology has been also successfully applied to the beneficiation of a variety of minerals including calcium carbonates, talc, and potash.

Nov 1, 2011

By R. H. Colquhoun, A. W. Bolland, H. J. H. Pieterse

"American Barrick Resources Corporation acquired the goldstrike property in north eastern Nevada in early 1987. Since that time, the company has undertaken an extensive development program. This paper will overview the milling, autoclaving, and heap leaching facilities which are part of the $400-million Betze development plan. Gold production at the Mine has increased from 40,000 ounces per annum in 1987 to more than 500,000 ounces in 1991. And in 1992 Goldstrike will be the single largest North American gold mine when it produces 1,000,000 ounces.1. SUMMARYAmerican Barrick Resources Corporation acquired the Goldstrike property in northeastern Nevada in early 1987. Since that time, the company has undertaken an extensive development program. This paper will overview the milling, autoclaving, and heap leaching facilities which are part of the four year, $440- million Betze Development Plan. Gold production at the Goldstrike Mine has increased from 40,000 ounces per annum in 1987 to more than 500,000 ounces in 1991. In 1992, Goldstrike will be one of the largest North American gold mines, when it produces appro approximately 1,000,000 ounces.2. INTRODUCTIONAmerican Barrick Resources Corporation is in the process of developing the Betze gold deposit, located on Barrick's Goldstrike property in the Carlin area of Nevada, U.S.A.The Goldstrike Mine has 17.9 million ounces of proven and probable reserves and an additional 460,000 ounces of possible reserves. Additionally, the Purple Vein deposit, one mile north of the Mine, is expected to add at least 4 million ounces of reserves by year end 1991.The Goldstrike ore body contains both oxide and sulphide ore. The largest part of the reserves are contained in the high grade, deep sulphide ore. Mining of the sulphide ore contained in the Betze deposit involves the removal of large quantities of overlying oxide ore. Oxide ore is treated through one of the following processes:-"

Jan 1, 1992

By R. S. Fukuhara, M. J. Allan

"Highmont, a wholly owned subsidiary of Teck Corporation, operates a 25,000 ton/day mine and concentrator located in the Highland Valley of British Columbia. Construction of the plant commenced in the spring of 1979, and production from one grinding line began in late December 1980. The second grinding line began production in March 1980.The ore body consists of two main zones, the east and west pits, containing 134 million tons of ore, averaging 0.26% Cu and 0.27% Mo. Mineralization consists mainly of chalcopyrite (2/3), bornite (1/3), and molybdenite.The concentrator design incorporates an A-B-C grinding circuit (auto mill ball mill - crusher), followed by bulk flotation, copper-moly separation and leaching for moly concentrates. The two grinding and bulk flotation circuits are parallel and independent. Concentrate storage is provided between bulk flotation and copper¬moly separation and also ahead of molybdenite leaching. The plant design has been previously described in some detail. (""THE HIGHMONT CONCENTRATOR"" by C. V. Sibbald, CIMM Bulletin, March 1981).This paper will outline some of the problems associated with the construction, startup and early operation phases of the concentrator. The objective is to help others avoid some of the potential pitfalls by outlining those areas where problems occurred, or where things went well. Criticism of design or equipment is not intended."

Jan 1, 1982

By J. E. Udd

"In early 2000, CANMET-MMSL was engaged by the Ontario Ministry of Labour (OMOL) to conduct an international study of the practices, in several key mining jurisdictions, of determining the criteria that are used to decide when the wire ropes used in mine hoisting are to be retired from service. Subsequently, the author visited key officials and institutions in Canada, the United States, the Republic of South Africa, the United Kingdom, Germany, and Poland. Material from the Australian province of New South Wales and Hungary was also included.The report that resulted included, among other sections: (1) the history of wire ropes and trends in manufacturing technology; (2) a review of mine hoisting practices; (3) the requirements regarding safety factors; (4) a review of the various operations and their potential future development; (5) the criteria for rope replacement; (6) potential future developments that could take place in both hoisting and rope inspection practices in Canada; and (7) recommendations.Subsequently, the report was issued by OMOL, and as a CD-ROM by CANMETMMSL. In this paper the author presents the key findings and the recommendations made in the study."

Jan 1, 2004

By Michel Dagbert, Mohammed Harfi

"Abstract - The Draa Sfar polymetallic deposit, at about 16 km NW of Marrakech in Morocco, is a massive sulfide zone at the contact between an underlying volcanic and an overlying clastics sequence. The mineralized body is a flat lens with schistosity and "boudinage," tilted to the west and with a strong dip to the east. The lens extends over a strike length of about 2 km and from surface to a depth of about 1 km, with thickness varying from 1 m to almost 30 m. It has been intersected by about one hundred surface drill holes and, in its south part, by about thirty underground fan holes from two exploration levels at depths of 300 m and 400 m. On these two levels, the massive sulfide zone has been channel sampled over a cumulative length of about 0.7 km. Results from drill and channel samples are used to estimate the resources of the orebody according to several methods: sections, polygons around intercepts on a longitudinal plan, grids on the same longitudinal plan with various distance weighting methods including kriging and, finally, a 3D grid with the same range of interpolators. A comparison of the various estimates delineates the important factors in deriving resources for this type of deposit. Those factors are mostly geological and related to the interpretation of the geometry of the two limiting surfaces of the zone. For the 3D gridding, the authors have devised a new and original method that constrains the interpolation of blocks from samples to a geometry of limiting surfaces. The resulting model shows internal grade variations that parallel fluctuations of zone thickness and orientation without having to re-orientate the search window in each block. Résumé - Le gisement polymétallique de Draa Sfar, situé à environ 16 km au NW de Marrakech est un horizon de sulfure massif au contact d’une formation volcano-sédimentaire de base et d’une formation détritique sur-jacente. Le corps minéralisé se présente sous forme d’une méga-lentille aplatie, schistosée, boudinée et déversée vers l’ouest avec un fort pendage vers l’est s’étendant sur une longueur de 2 km et une profondeur de près de 1 km avec une épaisseur variant de moins d’un mètre à près de 30 m. Il a été reconnu par plus d’une centaine de sondages de surface et, dans sa partie sud, par une trentaine de trous souterrains en éventail à partir de deux niveaux à des profondeurs respectives de 300 m et 400 m. Sur ces mêmes niveaux, des traçages ont permis de rainurer le minerai sur une longueur cumulée de 0.7 km. Les données de sondage et de rainurage ont servi à estimer les ressources du gisement selon plusieurs méthodes : sections, polygones sur longitudinale, grille sur longitudinale avec différentes pondérations en fonction des distances incluant le krigeage et enfin grille tridimensionnelle avec le même éventail de pondérateurs. La comparaison des estimés obtenus permet de mettre en évidence les facteurs importants dans l’estimation des ressources de ce type de gisement. Ces facteurs sont essentiellement géologiques et relatifs à l’interprétation de la géométrie des limites des corps minéralisés. Pour l’estimation sur grille tridimensionnelle, on a mis au point une technique originale qui calque l’interpolation des blocs à partir des échantillons sur cette géométrie des surfaces de contact. Le modèle résultant montre des variations internes de teneurs qui épousent les fluctuations d’épaisseur et d’orientation de la zone sans qu’il soit nécessaire de ré-orienter les fenêtres de recherche dans chaque bloc."

Jan 1, 2002

By Rudy Tenbergen, Dick Farmery, Jim Naylor

"Paste backfill has replaced cemented rock fill as one of the components to improve ground · control and mine safety at the Macassa Operation of Kinross Gold Corporation in Kirkland Lake, Ontario. It is the first operation to utilize "" flash thickening ""of very fine gold tailings to a paste consistency in the ""Paste Production and Storage Mechanism"", a joint technical development of Inco and GL&V. The tailings paste is mixed with alluvial sand to produce an engineered quality paste backfill. The development leading up to the decision to proceed with this novel technology is discussed, as well as commissioning of the backfill operation.IntroductionThe occurrence of a major rockburst on November 23, 1993 prompted a review of mining and backfill procedures at the Macassa No 3 shaft . This shaft is some 7238 ft deep and lies in a mining belt that is prone to seismic events. The recommendations were to change the mining from underhand cut and fill to mechanized long hole stopping and to look at alternatives to the rockfill backfill system in place. The Macassa cemented rock backfill operation, while producing the desired fill stiffness had drawbacks as compared to paste fill. With paste fill, placement rates are faster, more openings can be filled, it is less expensive and less prone to the occurrences of compensable incidents.Macassa mining personnel visited the Sudbury operations of Inco in 1993, where development on paste backfill was in progress. As some of the R&D was taking place with funding from the Premier's Council Technology Fund of the Ministry of Trade and Technology of the Province of Ontario , Inco personnel at that time did some feasibility and conceptual consulting on the use of paste fill for the industry. Inco had developed the use of alluvial sand paste fill, an engineered blend of alluvial sand and tailings fines and was doing development work to eliminate the ""conventional"" way of producing paste from mill tailing by thickening and filtration. This latter development work was taking place with GL&V Ontario. That work led to the filing of a joint Inca/ GL&V patent application for the PPSM, the Paste Production and Storage Mechanism with all marketing rights being held by GL&V."

Jan 1, 1997

By Norman O. Lotter, André R. Laplante

"The pursuit of concentrator surveying for purposes of metal accounting or process optimization has not yet connected with the well-published realm of geostatistics. The reality of lognormality in time has seldom been discussed. One publication by Krige, 1962, examined such effects for a gold concentrator in South Africa, towards an information system that would provide feedback to the mining and surveying teams on grade control of ore mined.During present studies which are designing and testing a new survey model, called statistical benchmark surveying, it was found that the distributions of feed, concentrate and tailings bear significant residual signs of the parent lognormality in space. The multiple hosting of paymetals in different mineral species complicates the understanding of these distributions. These features have to be recognized and treated in order to perform appropriate quality control on the diagnostic sampling performed in the pursuit of statistical benchmark surveying.It is shown in this paper that the above two features can actually be used to advantage in the diagnosis of continuous periods of operations data ahead of such surveying, including the estimation of recoverable paymetals in flotation tailings from a graphical method.INTRODUCTIONAssessment of Concentrator PerformanceMilling and flotation, sometimes accompanied by gravity separation, are well-established unit processes, which have traditionally been used to treat ore that has been mined. This is because these processes liberate, then separate, the valuable minerals, which contain paymetals, from host gangue. This is often done by a combination of crushing and grinding processes, or autogenous grinding, to liberate the paymetal minerals, followed by gravity separation and/or flotation, to separate these valuable minerals into a concentrate, or several concentrates. These concentrate(s) have a lower bulk than the parent ore from which they are derived. Further, they contain a high percentage of the valuable minerals. Accordingly, they are more economically treated in subsequent beneficiation processes than the ore from which they were produced."

Jan 1, 2005

By L. Parthasarathy, S. K. Pan, M. P. Srivastava

"Total iron ore reserves in India, as reported by the Indian Bureau of mines, are 23.6 billion tons. Hematite iron ore reserves constitute about 45 % of the total reserve. If we go by the National Steel Policy-2005 projections, India’s supply of hematite iron ore would not last more than 40 years. Laboratory investigations were carried out for the development of a process flow sheet for treating low grade as well as Banded Hematite Quartzite (BHQ) iron ore. The purpose of these investigations was to aim for better resource utilization.Beneficiation studies were conducted on samples of low grade and siliceous iron ore from the Dalli mines, a captive mine of the Bhilai Steel Plant and BHQ ore from Southern states of India. The process flowsheet, developed for upgrading of low grade iron ore, incorporates wet screening of the ore at 0.5 mm, followed by grinding of the +0.5 mm fraction to below 0.5 mm. The whole –0.5 mm fraction, after grinding, was treated in a conventional hydro-cyclone and stub cyclone followed by treatment in Wet High Intensity Magnetic Separator (WHIMS). This resulted in a concentrate product having >66% Fe content from a feed containing 55.5% Fe with an iron recovery of 48 %. The process flowsheet developed for treating BHQ ore in the laboratory resulted in an increase in iron grade in the concentrate from 43.4 to 61.3 Fe % with a yield of 51.7 % .INTRODUCTIONThe classification of Indian iron ore resources have been made compatible with United Nations Framework Classification (UNFC), which is more scientific and has been adopted in most countries in the world. Iron ore reserves and resources estimated using the UNFC classification system, as of April 01,2000 are about 12,906 million tons of hematite ore and 10,628 million tons of magnetite ore. The Indian Bureau of Mines (IBM) has given a breakdown of these reserves by designation as either lumps or fines of hematite iron ore (Table 1). The percentage of the reserves reported lumps and fines are 42 and 34% of the total reserves respectively. High grade iron ore is less than 10% of the total reserve."

Jan 1, 2008

By Derek J. Cyr

Climate has an immense impact on the properties of Athabasca oil sands and the ease or difficulty with which it is excavated and extracted. During the winter months, exposed oil sands surfaces freeze. When hydraulic and electric shovels used in the various operations in the Fort McMurray area excavate the benches, large frozen lumps are created. These lumps are either destined for a lump dump where increased costs are incurred due to rehandle, or they are sent to the primary crushers where they can cause significant downtimes by jamming the crusher. The crusher down time can sometimes be in the order of hours of lost production. Studies on data from two consecutive winters at Syncrude Canada?s North Mine show a high correlation between climate and the generation of frozen oil sands lumps. Temperature, ground cover, traffic, bench exposure time, oil sands grade and moisture content all contribute to this problem. A 1D frost penetration model was used to predict the depth of frost expected in oil sands and the corresponding likelihood of frozen oil sands lumps. To combat the challenge of frozen lump generation, a number of proactive and reactive measures can be taken: artificial snow, shallow ponds, scheduling, blasting or ripping.

May 1, 2004

By S. Schwartz, T. Bilney

"Over recent years a number of techniques have been developed as part of the AMIRA1 P9 project to represent mathematically or measure directly sub-processes occurring in flotation cells. These include the determination of:•,?a machine parameter (bubble surface area flux, Sb);•,?a froth parameter (froth recovery, Rf );•,?entrainment and drainage parameters (???and d); and•,?an ore floatability parameter (Pi).These flotation parameters allow the plant engineer to develop a model of the flotation circuit that can be used as a powerful tool to diagnose the performance of that circuit. The recently developed JKSimFloat V6 flotation simulator uses these parameters to predict the flotation circuit performance that would arise from changes in operating conditions and circuit configuration.This new flotation technology was applied to the Placer Kanowna Belle Gold Mine in Western Australia. A series of plant surveys, cell characterisation measurements and laboratory batch tests were conducted to determine the flotation circuit model parameters to be used within the JKSimFloat V6 simulatorA thorough flotation circuit analysis was then performed at Kanowna Belle using JKSimFloat V6. The recommendations that were provided by this circuit analysis have resulted in large improvements in the flotation performance at Kanowna Belle. These include a 1.3% increase in flotation gold recovery and a substantial decrease in operating costs. The analysis is still ongoing, however, the benefits already obtained from applying this technology have resulted in a US$1.3 million a year improvement to the mine."

Jan 1, 2005

By Jim Truskoski, Alain Bouchard, Andy Kerr, Germain Labonté, Jim Barrett

"Improving mill grade recovery relationships is always good business. INCO’s Clarabelle Mill has just undergone a $16 million process upgrade that was designed to improve nickel recovery by 2%. The “Mill Redesign Project” was completed on time, under budget and delivered the promised improvement in recoveries.This paper describes the methodology of the Mill Redesign Team, details of the process improvements and the critical success factors that helped the team deliver on its promises.With a payback of under one year, the Mill Redesign Project will play a key role in ensuring a competitive edge as INCO embarks on its second century of operation.INTRODUCTIONIt is not uncommon in milling operations to encounter a crisis. That is the point when the process does not behave as expected and fails to respond to the increasingly desperate efforts of the metallurgists and operators. Flowsheet and process changes are attempted and abandoned. With luck, one or more of the changes achieves some mitigation of the original problem or more usually, the original cause of the problem disappears. Regardless, the metallurgist can sit back and bask in the apparent success of his or her endeavours.Less common is when a problem is carefully diagnosed, a team put together to explore all avenues and recommend a path of action that is implemented on time, on budget and immediately delivers on the promises which are sustained over time. This is one such story. It is the story of the Mill Redesign Project at INCO’s Clarabelle Mill in Copper Cliff, Ontario.BACKGROUNDThe Clarabelle Mill was built in 1971 on the southern rim of the Sudbury basin. At that time it was one of four mills operated by INCO in the Sudbury area. During the 1970’s, 80’s and 90’s, the need for increased process efficiency, higher levels of sulphur rejection to tails and the concurrent development of high capacity mills and flotation cells, resulted in the consolidation of INCO’s Sudbury area milling operations into a single, expanded facility at Clarabelle."

Jan 1, 2003

By S. Stefanizzi

In the present paper, numerical simulations based on a finite/discrete element approach are used to study deformation and failure process during standard rock mechanics. FEM/DEM modeling has been used as available with the ELFEN code, which explicitly model the transition from continuum to discontinuum. The transition is simulated through a crack nucleation and propagation that obeys to the Griffith?s failure criterion. If the fracture criterion within the intact rock (represented by FEM) is met, a new crack (represented by DEM) is initiated. Remeshing allows the fracture process through the FEM mesh to be tracked and visualized, thus contact properties can be assigned to pre-existing fractures and newly generated fractures. In this study, compressive tests of rock samples are simulated. The applicability of ELFEN to properly and efficiently simulate typical laboratory rock mechanics tests, with reference to the rock fracture process, is described in detail. In addition, an indirect validation of the extensional strain criterion proposed by Stacey (1981) is given.

May 1, 2009

By T. Lux, M. Hanel, Degel, A. Filzwieser, R., H. Joubert

It is the increasing demand for an economic and cost saving operation mode that requires effective cooling in order to achieve low refractory wear and good furnace lifetime, which is making cooling technology an important aspect of furnace operation. In addition, the requirements for safety are getting more and more into focus. However, the use of water—today’s standard cooling medium—has major drawbacks as it can cause problems both during furnace start up and operation, namely hydration problems, corrosion, and explosion. Not to forget the severe risks for the operators as well as economical damage in case of a malfunctioning water cooling system. With this new and patented cooling technology ILTEC and the ionic liquid IL-B2001 as the cooling medium, it is possible to realise a water-free cooling solution and therefore the door is wide open to rethink existing and conventional cooling solutions. Furthermore, there is also the chance to recover heat from the process in a more efficient way. However, since the technology is novel and unique there are a lot of concerns and doubts regarding safety for plant operators and employees. The paper is intended to cover both: highlighting the enormous potential of the technology but also to eliminate concerns mainly caused by rumour and unawareness. INTRODUCTION All of us are aware of the risks when water is used as a coolant and placed in the vicinity of the liquid metal phase. Unsuitable design solutions or wrong operation modes of the furnaces or failures of refractories can cause a direct contact of water with liquid metal. The consequences can lead to equipment failures, vessel destruction but even worse to injuries and even fatalities. Over the past decades, countless incidences were reported. Fatal accidents caused by water coming into contact with liquid metal happen every year (Oterdoom, 2014; Filzwieser, Konetschnik, Filzwieser, Wallnerm & Preiss, 2014). With the novel ionic liquid cooling technology virtually all negative effects of a water cooled system regarding safety are eliminated and even additional benefits can be provided (Voermann, Ham, Merry, Veenstra, & Hutchinson, 1999;Verscheure, Kyllo, Filzwieser, Blanpain & Wollants 2006; Wallner, Filzwieser & Kleicker 2006). The fact that no explosion occurs when IL-B2001 gets in contact with molten metal results in a revolutionary solution for the metallurgical industry in terms of safety—new safety standards can be achieved.

Jan 1, 2019

By Valentin Choquenaha Bombilla, Oscar Alvarez Muiloz

"Tintaya’s basic production line is copper concentrate, which has an important gold content. The process used is flotation; the objective of the metallurgical department is to obtain the best results in the copper recovery without neglecting the gold, using very specific reagents. Copper recoveries are considered high, nevertheless every day emphasis is placed upon increasing those recoveries. Regarding gold, optimum recoveries could not be achieved with flotation; and implementation of a gravity circuit was considered.According to microscopy studies, the coarse and very fine grains of gold in native form are lost to tails. The native gold due to its high specific gravity is concentrated at the underflow of the cyclone, remaining in the circulating load of the circuit. It reaches three times the concentration compared to the head grade entering the ball mills. This re-circulation generates very fine and laminated gold particles inside the ball mill, passing to the classification stage making a short circuit to the overflow of the cyclone.The very coarse gold particles as well as the thick flakes of gold do not react favorably to the conventional flotation process; thus studies that have included gravity separation have been conducted to increase the gold recovery. Part of the research included concentrating tables, jigs, and Knelson Concentrators. The Knelson Concentrator proved to be the best selection in terms of metallurgical performance and recoveries considering the throughput and operation conditions of the Tintaya Plant.The gravity concentration circuit with the Knelson Concentrator was commissioned in BHP Tintaya in October 1998, as per the flowsheet shown later on. Presently the global gold production surpasses any estimated expectations.Present efforts are directed towards showing the evaluation and optimization of the different parameters that govern the performance of the Knelson concentrator, as well as illustrating the difficulties and successes throughout the operating period.In the first year of operation 200 tons of gold concentrate have been produced with an average concentrate grade of 320 gramdton, having paid back in full the cost of the automated KC-XD- 48 Knelson Concentrator, the peripheral equipment, and the cost of the installation."

Jan 1, 2002

By J. R. Goode

"The Las Cristinas deposit contains about 10.2 million ounces of gold at a grade of 1.3 g/t. The deposit comprises a layer of fully oxidized saprolite (SAPO), a layer of sulphide-enriched saprolite (SAPS), carbonate leached bedrock (CLB) and carbonate stable or un-leached bedrock (CSB). Gold occurs at about the same level in all lithological groups. The bedrock units contain minor amounts of copper (about 0.1%) as chalcopyrite, while SAPO contains virtually no copper it having been leached and deposited in the SAPS zone.A previous owner started investigation of the Las Cristinas deposit in Venezuela in 1991. Over the next seven years, 1174 holes with a total length of 159 km were drilled, extensive metallurgical testwork, including pilot plant operations, were conducted and feasibility studies were completed. Construction was started in 1997 and again in 1999 but was suspended.Crystallex has been producing gold in Venezuela since the early 1990’s. In 1997, Crystallex acquired Inversora Mael which had held two of the claims to the Las Cristinas concessions since 1986. In September 2002, Crystallex entered into a definitive agreement with the Corporación Venezolana de Guayana, (CVG), to develop the Las Cristinas deposit.An extensive program of studies and testwork was started in early 2003 to determine an optimum development plan for Las Cristinas. Mine Development Associates, SNC–Lavalin Engineers and Constructors, SGS Lakefield Research Limited, J.R. Goode and Associates, and Professor A. Laplante at McGill University acted as the main contractors.Because of the potential value of by-product copper, earlier flowsheets used carbon-in-leach for SAPO, but processed all other ore types by flotation to produce a gold-copper concentrate with cyanide leaching of cleaner tailings to maximize gold recovery. Cyanide recovery was necessitated by the high copper content of the leach feed. Initial studies of available data by Crystallex revealed that direct leaching of all ore types would provide about 11% more gold recovery than the previously selected flotation route with reduced capital and operating costs.Bench and pilot scale studies have confirmed that a SAG-ball mill-gravity-CIL route is very effective for all ore types and will give about 89% gold recovery. This paper describes the recent testwork, discusses the proposed plant design, and presents economic data."

Jan 1, 2004

By M. Cai

A practical simple method is proposed to estimate the tensile strength (st) of strong brittle rocks from the strength ratio of R= sc/st = 8 sc/sci, where sc is the uniaxial compressive strength and sci is the crack initiation stress in an uniaxial compression test. 8 is the Griffith strength ratio and the term sc/sci accounts for the difference of crack growth or propagation in tension and compression in uniaxial compression tests. sci can be reliably obtained from volumetric strain measurement or acoustic emission (AE) monitoring. With the strength ratio R determined, the tensile strength can be indirectly obtained from the result of uniaxial compression tests. In addition, a practical estimate of the Hoek-Brown strength parameter mi is presented and it is suggested that mi = 12 sc/sci can be applied to strong, brittle rocks in high confinement zone and mi = 8 sc/sci can be applied to low confinement to tension zones. It is found that the predicted tensile strengths and Hoek-Brown strength parameter mi using this method are in good agreement with test data. The rock strength parameters like st and mi, which require specialty tests such as direct tensile (or Brazilian) and triaxial compression tests for their determination, can be reasonably estimated from uniaxial compression tests.

May 1, 2009

By A. R. Barnes, N. O. Lotter

Recoverable economic copper sulphide minerals such as chalcopyrite, bornite, chalcocite and covellite often occur together in varying proportions in the major copper-bearing ores, and have individual flotation requirements and characteristics. Pyrite also occurs in these ores to varying extents as the sulphide gangue, and is problematic because of its natural tendency to float quickly and easily. In a bulk sulphide float, selectivity against pyrite is desirable, particularly if it does not host other paymetals such as gold or silver. At the same time it is a requirement to float all of the copper sulphides despite their electrochemical differences. The electrochemistry and semiconductor properties of these minerals are reviewed, together with implications for flotation with and without collector addition. Mixed collector systems for the improved flotation of these sulphides are proposed as a solution. The use of xanthate and dithiophosphate in the collector suite allows the co-existence of dixanthogen and free dithiophosphate radical because the latter has a higher redox potential requirement than xanthate to oxidise to the dithiolate. Because some of these minerals require dixanthogen, and others, free thiolate, to generate surface hydrophobicity, a bulk flotation of all the species becomes possible in the overlapping area of Eh and pH between the two dithiolate equilibrium lines on the Pourbaix diagram. The arsenic-signature copper minerals are added to the study, since many copper operations encounter arsenic as a penalty element in the saleable concentrate. It is shown that the addition of arsenic to the copper and iron sulphides alters the semiconductor and electrochemistry properties, and in turn, its flotation characteristics. The degree of mineral association and liberation between these minerals can be a complicating factor due to textural associations, and should also be considered in the process as a next step.

Jan 1, 2016

By D. Linzey

"History of Whitehorse Copper BeltThe first discovery of copper on the Whitehorse Copper Belt is reported to have been made by miners on their way to the Klondike in 1897. By 1899 the district had been well prospected and many of the presently known deposits had been staked.The first shipment of ore was from the Copper King property in 1900. This consisted of 9 tons of hand picked ore grading 46.4% copper. It was not until the period between 1912 and 1917, the production years of the Pueblo Mine, that significant ore shipments were made. Total production was 140,000 tons at 3.5% copper. An underground disaster killed six men and closed the mine in March 1917.Although the general area was dormant until after World War II, by 1947 geological mapping, magnetic surveys and diamond drilling had been done on the important showings. In 1954 Mr. Aubrey Simmonds directed the formation of Imperial Mines and Metals, which acquired by option and staking a large part of the Whitehorse Copper Belt. In 1957 Mr. Arnold Pitt reorganized the company as New Imperial Mines. With financing from Sumitomo and Toronto-Dominion Bank, a mill was built and production was started from the Little chief orebody by open pit in 1967."

Jan 1, 1977