Search Documents

By Valdeci Paula Alvarenga, Sergio Luiz Costa, Itavahn Alves da Silva, Filipe Bueno Carvalho, Varadarajan Seshadri, Carlos Antonio da Silva

Use of fluorspar in steel refining operations is one of the environmental concerns and as such reduced consumption of this material or substitution of the same is one of the objectives. Industrial runs were carried out at Aperam Steel making convertor unit (Timóteo, MG, Brazil) using recycled/briquetted slag for partial or complete substitution of fluorspar. Samples were collected from the metal bath and slag after oxygen blowing to assess dephosphorization with several combinations of recycled/briquetted slag and fluorspar. The results showed that partial substitution of fluorspar by BOF slag briquettes did not affect the efficiency of dephosphorization. In general average Phosphorus content was reduced to 0.010% in the case of partial substitution compared to 0.016% in the regular refining procedure with no substitution. This replacement also resulted in 40% reduction of the fluorspar consumption in the converter

Jan 1, 2015

By Richard D. Hagni

Quantitative techniques have become increasingly important in recent years in the study of ore minerals. Precise measurement of indentation hardness and reflectance is the most important quantitative ore microscopic technique for mineral identification. Reflectance measurements of various wave lengths under monochromatic light provide the data necessary for the preparation of spectral reflectance curves and for the quantitative determination of an ore mineral's color. The procedures for the measurement of indentation hardness, reflectance, and color coordinates have recently been standardized and 204 items of quantitative data for ore minerals are now available in the first issue of the quantitative data file of the International Mineralogical Association's Commission on Ore Microscopy. A number of systems utilizing these quantitative data for systematic ore mineral identification have been published and others are in preparation. Rotation properties, although not included on the data cards, are useful in the identification of certain groups of minerals. Other aspects of quantitative ore microscopic techniques include the utilization of automatic image analysis for mineral percentage determinations and the use o~ various microbeam instruments for elemental analyses. These techniques provide a greatly improved basis for mineral identification in mineralogical and beneficiation studies.

Jan 1, 1981

By Ben Hogg

Since the development of the top-submerged lance (TSL) technology for copper and lead smelting by the cooperation of Mount Isa Mines (MIM), now owned by Glencore, and the Commonwealth Scientific Industrial Research Organisation (CSIRO) the core of the ISASMELT™technology has always resided in the lance system. Through continuous innovation and operation of our own smelters, first at MIM, subsequently at Mopani, and also at both the Kazzinc Copper and Kazzinc Lead smelters, Glencore Technology have expanded the core equipment supply to enhance the plant operability. The success of Glencore Technology’s expertise can be directly measured by the success of the Kansanshi Copper Smelter plant, which achieved 100% nameplate capacity within three months of start-up. This paper describes the ISASMELT™ core equipment and how it is applied to smelt sulfide materials. It highlights the strength of the ISASMELT™: continuous innovation to facilitate the versatility and continued increased capacity with every plant implementation.

By Z. Jing, L. Qihou, C. Jun, L. Hui, Z. Yumeng

Three phases of Bi2O3 were first synthesized by extraction-stripping precipitation and post decomposition from BiCl3 leaching solution. The as-prepared Bi2O3 were characterized by X-ray powder diffraction (XRD), Fourier transform infrared spectra (FT-IR), scanning and transmission electron microscopy (SEM, TEM), UV-vis diffuse reflectance spectroscopy (UV-vis DRS), Brunauer-Emmett-Teller (BET) and X-ray photoelectron spectroscopy (XPS). The photocatalytic performances of the oxides were investigated by decomposing rhodamine B (RB) under visible irradiation. It shows that the Bi2O3 with different crystal structures and morphology were obtained under different decomposition temperature. The band gaps of as-prepared samples were 2.36, 2.41, and 2.78 eV for b-Bi2O3, a-Bi2O3, and d-Bi2O3, respectively, and the photocatalytic activities followed the order: b-Bi2O3 > a-Bi2O3 > d-Bi2O3, which was in good accordance with the photoluminescence spectra measurement results. The b-Bi2O3 exhibited the best photocatalytic performance which can effectively degrade 99.23% RB within 240 min.

Mar 1, 2018

By Adam Powell, Salvador Barriga, Matthew Earlam

"The inert anode is a key enabling technology for dramatic energy and emissions reduction in extractive metallurgy. In molten salts, the materials challenge is nearly insurmountable: the anode must conduct electrons at high temperature in a pure oxygen and molten salt environment. A solid electrolyte, e.g. zirconia, between the salt and anode removes the molten salt stability constraint, and can act as a container for a liquid metal anode. This can be liquid silver for oxygen-generating inert anodes, or several metals for natural gas-fueled anodes; it is possible to switch between these modes. The solid electrolyte brings several other benefits: it eliminates molten salt contamination of the anode gas, creates a reducing environment enabling low-cost steel vessels, increases current efficiency, and eliminates carbon contamination of the product. New developments presented here, including current collector and low-cost anode designs, amplify these benefits for producing aluminum, magnesium, rare-earths, and other metals.IntroductionReactive metals such as magnesium, aluminum and rare-earths play increasing roles in efficient transportation and clean energy. In response to new fuel economy standards, automotive OEMs are planning large increases in use of aluminum and magnesium to reduce vehicle weight. Rareearth permanent magnet motors and generators exhibit better power-to-weight and efficiency than induction motors and other designs, making this today's primary motor technology for hybrid and electric vehicles, and for wind turbines. Nickel metal hydride (NiMH) batteries with lanthanum are dominant in hybrids. In 2011, transportation comprised 28.6 out of 103.1 EJ of US energy consumption [1] and 1,845 out of 5,471 million metric tonnes (MMT = 109 kg) CO2e of US greenhouse gas (GHG) emissions [1], creating big targets for economy-wide reductions.Unfortunately processes for making reactive metals for these applications are very inefficient and heavily-polluting. In primary aluminum production, Hall-Heroult cell electricity use [2] is more than double the reaction enthalpy due to heat losses through frozen cryolite side-walls and anode gases, graphite anode plants add significant energy use and GHG emissions [2] (see Table 1). Magnesium is even worse: silicothermic reduction by the Pidgeon process in China produces about 85% of the world's magnesium using coal or coke gas [3]. Chloride electrolysis begins with high-purity MgO and requires carbochlorination or hydrochlorination and costly chloride dehydration [4]—rendered unnecessary for aluminum by the Hall-Heroult cell. Production of neodymium and lanthanum with graphite anodes leads to inconsistent carbon content: small cells make 1 kg batches for analysis, sorting and sale by carbon content, with very high labor and analysis costs. And vertical electrodes give no incentive to reduce anode effect: some reports indicate that China's rare-earth metal industry emits more CF4 and C2F6—with global warming potential (GWP) 6500 and 9200 times CO2 respectively—than China's aluminum industry [5]."

Jan 1, 2014

By Zhang-Guang Gao, Ming-Mei Zhu, Rui-Rui Zhao, Chao Jiang

This paper focuses on the CaO-SiO2-FeO-MgO-MnO-P2O5 slag system that represents the major components of dephosphorization slag in BOF. Phosphorus distribution between 2CaOSiO2-3CaOP2O5 Solid Solution and Liquid Slag were analyzed by FactSage. The effects of slag content, basicity on the distribution ratio of P between the solid solution phase and the liquid phase (LP) and the percentage content of P in solid solution phase and liquid phase have been discussed. The results show that, with the increase of basicity, LP (wt%) decreases until the basicity reaches 1.9, then it turns to increase. LP (wt%) increases gradually with the increasing amount of FeO or P2O5.

Mar 1, 2017

By François Larouche

Since their commercialization in the early 1990s, lithium-ion batteries (LIBs) have become ubiquitous for powering a myriad of portable electronics. Their usage now extends to the automotive industry and stationary energy storage market. With an average life of 6.2 years and the strong demand, the volume of spent LIBs has increased exponentially, making recycling mandatory. Currently, recycling/ recovery of spent LIBs is limited in comparison to all other types of batteries. The current processes focus mainly on the recovery of the most valuable metals such as cobalt and nickel, leaving lithium and phosphate in a low value end-product. It is necessary that new advanced recycling technologies are developed for the recovery of spent LIBs both from an economic and environmental perspective. In this paper, the current R&D status of LIBs recycling is reviewed with the emphasis placed on hydrometallurgical processing opportunities for Li-ion and Li-solid state batteries.

By M. Elbert Nigri

Radioactive wastewaters from nuclear source of electrical energy production need to be treated and disposed of properly. Sr, Ca, Mg and Ba are common elements in this effluent, which can cause incrustation in process equipments and being unsafe to human health (90Sr). Fixation of CO2 can be applied to remove the ions mentioned before and to provide a solution where CO2 is sequestered and the deleterious elements precipitated, becoming one of the possible steps to reuse the water into the process. Moreover, removal of several metals from distinct wastewater has been evaluated using bone char through adsorption. The chemical similarity between calcium and strontium makes the exchange of these two metals favorable in the hydroxyapatite structure contained in bone char. This paper evaluated the combined action of precipitation and adsorption process with injection of CO2 and bone char addition in simulated nuclear wastewater. Removal levels of 89.0% (Sr) and 83.3% (Ca) were obtained in the combined process. The presence of bone char as seed increased the precipitation kinetics, allowing a Sr removal of 85.2% in five minutes, higher than 75.3% obtained in absence of seeds. However, removal of 91.6% (Sr) and 89.8% (Ca) were obtained in absence of seeds at 24 h. Analysis of solids have evidenced that CO2 was consumed to precipitate the metals as carbonates, since the hydroxides are formed at higher pH’s.

By S. Viswanathan, A. S. Sabau

"Dimensional changes between a pattern die and its corresponding investment casting part occur as a result of complex phenomena such as thermal expansion/contraction and hot deformation (elastic, plastic, and creep) during the processing of the pattern material (wax), mold material (shell) and solidifying alloy. Determining the pattern tooling dimensions is crucial to the dimensional control of the investment casting process. To date, computational methodologies have not been applied to the prediction of dimensional changes in investment castings.This paper deals with the evaluation of wax pattern dimensions, which is one important factor in determining pattern tooling dimensions in investment casting. Cerita 29-51, an industrial wax, is considered in this study. The wax pattern dimensions are determined by considering its thermo physical and thermomechanical properties, restraint of geometrical features by the metal die, and process parameters such as dwell time, platen temperature, injection pressure, and injection temperature.IntroductionThe investment casting process involves making a disposable wax pattern by injecting wax into a metal mold, building a ceramic shell mold around the wax pattern by the application of a series of ceramic coatings to the wax pattern, dewaxing the ceramic shell mold, and casting the alloy into the shell mold. Dimensional changes between the pattern tooling and its corresponding cast part occur as a result of thermal expansion, shrinkage, hot deformation, and creep of the pattern .material (wax), mold material (shell), and solidifying alloy during the processing [1]."

Jan 1, 2001

By Wankun Wang, Fuchun Wang

Based on the study of artificial neural network, the neural model was established for the prediction of germanium extraction from zinc oxide dust by microwave alkaline roasting-water leaching. Alkali-material mass ratio, microwave heating temperature, liquid-solid ratio, aging time, leaching time and leaching temperature were the significant factors for the process. The results indicated that the neural network prediction model was reliable, and the forecast values fitted well with the actual experimental values. The model could be used to predict the regeneration experiments with high credibility and practical significance. The accuracy of convergence of the model reached 10−5.

Mar 1, 2018

By Renato G. Bautista

The solvent extraction separation of nickel, cobalt and their associated metals have been considered for industrial application since the early 1960's. This review of the solvent extraction processes is limited to the industrial applications, pilot plant and the more extensive bench scale studies reported in the literature. The processes with their significant chemical and technological contributions are discussed in detail whenever the information are available. The application of solvent extraction to the nickel-cobalt processing has so far been limited to the secondary separation of nickel-cobalt containing feedstocks derived from other primary nickel-cobalt separation methods.

Jan 1, 1993

By M. Oliazadeh

Spodumene [LiAl(Si2O6)] is the most common and desirable economic lithium-bearing mineral due to its high lithium content. In Canada, there are several spodumene deposits at the development stage that have the potential to help narrow the forecast lithium supply gap stemming from the widespread acceptance and increasing use of electric vehicles. Spodumene processing can be conducted using Dense Media Separation (DMS), flotation or combination of both. If spodumene liberation is sufficient at coarse particle sizes, DMS can be used for primary lithium concentrate production and silicate gangue minerals rejection. If liberation is not sufficient, flotation is then the main processing route for spodumene concentration. Even in cases where DMS is a viable beneficiation option, flotation may still be required to process the DMS middlings and/or the undersize fraction which is outside the particle size range for DMS. Considering flotation as a technique for spodumene beneficiation, there are several alternatives including the use of mechanical flotation cells, column flotation cells, coarse particle flotation cells, and/or Staged Flotation Reactors (SFR), either alone or in combination. Ore sorting can be incorporated at the start of the spodumene flowsheet to remove gangue minerals, particularly amphibole and pyroxene in the early stages. The main objective of flowsheet development for hard rock lithium deposits is to evaluate the ability of these options to produce a spodumene concentrate with a concentrate grade above 6% Li2O, lithium recovery of above 80%, and with the minimum operating and capital cost. This paper aims to describe the various processing options available for the beneficiation of spodumene from hard rock deposits and compare the associated operating and capital costs for each.

By Hideharu Fukunaga, Jin Pan

"The recognition of Metal Matrix Composites (MMCs) as a means of providing high specific strength, high specific stiffness, excellent wear resistance, low thermal expansion and improved high temperature properties has led to a number of new processing, not previously used for plastic and ceramic matrix composites. As a primary fabricating process, the liquid methods are the major ones, which are reviewed briefly from the view of processing terminology. One of them, squeeze casting process is the most traditional and well-developed, because it is rapid, versatile and near-net shape production of materials. Two of new squeeze casting processes are presented to offer the hardness· controlled MMC and the· functionally graded MMCs as well as a newly developed whisker preform.I .IntroductionA large number of liquid processes and techniques including semi-solid liquid process are proposed. The most primitive process is ''pressure infiltration casting” of liquid metal into the fiber preform. It is called as follows depending on pressure and its source squeeze casting (1-4) by hydraulic ram, gas pressure infiltration casting (5, 6), vacuum infiltration, centrifugal casting (7), Lorentz-force-driven infiltration (8). The pressurizing on the liquid metal requests a large and stiff equipment, so pressureless infiltration technique has been developed using K2ZrF6 flux (9,10) while the mechanical properties are not high enough, and using H2 gas with Mg alloying element called pressureless infiltration casting (11-13), spontaneous infiltration process (14) and PRIMEX (15). In those processes, no severe reaction occurred between the reinforcement and matrix molten metal. In early l 990's, the reactive processing with pressure or without pressure, in which one material is totally transformed into another of the required shape, eq. assisted oxidation, has been developed, called reaction squeeze casting (16,17), DIMOX (18) reactive infiltration casting (19,20), and in-situ process (21,22). Die casting of SiCp/Al alloy (23,24) and thixocasting of SiCp/Mg alloy (25) are also applied to produce the machine component of MMCs."

Jan 1, 2000

By Georgios N. Anastassakis, Nickolaos Georgiou

"Soil contamination by oil as well as by other organic pollutants poses a major problem to the environment. Various methods have been used to remove organic contaminants from soil, such as: biological, thermal, chemical and physical. Methods based on Mineral Processing principles have also been used (cyclone separation, gravimetric separation, attritioning and washing). This paper studies the possibility to remove a rich-in-contaminant soil fraction by applying flotation. The contaminated soil was artificially prepared by mixing soil with diesel fuel. Sodium dodecylsulfate (SDS) and a tertiary amine (TA) were used as collectors. The effect of collector quantity added and conditioning time was studied. The results showed that the removal of a rich-in-contaminant soil is feasible while a clean fraction is also obtained. In several cases, the removal of oil-contaminated soil approaches or reaches 100%. Introduction Human activities are intimately associated with environmental pollution to the air, water and soil, as well. Soil pollution from inorganic and organic compounds is of equal importance with that of air and water, as it results in soil degradation and its concomitant problems with respect to meeting the human needs (house building, agriculture etc). Heavy metals along with their compounds are encountered among the most usual soil inorganic pollutants. The corresponding organic soil-pollutants are oil, oil-derivatives, pesticides, various aromatic (benzene, phenols, cresols, toluene etc) and poly-aromatic (naphthalene, anthracene etc) hydrocarbons, as well as various other organic compounds (pyridine, cyclo-hexane etc). Oil remains the basic energy source sharing 38% of the global needs, being followed by coal and gas with a share of 26 and 21% correspondingly [1]. The entire activities related with oil production, transport and consumption promote pollution in the air, water and soil. Consequently, soil pollution from oil is favoured at refineries, storage sites (due to possible pipe and tank leakage, tank cleaning works, loading and transportation) and, finally, at the oil-selling sites. Oil (or diesel-oil) fuel is a mixture of hydrocarbons, with 10-20 carbon atoms in the chain of each. It is mainly composed of paraffins, naphthenes and various aromatic compounds. In general, oil is composed of 20-30% in aromatic compounds, 5-6% in naphthenes and the rest is paraffins [1]."

Jan 1, 2008

By Guan-Yong SHI, Cong Wang, Zhi-he DOU, Ting-an ZHANG, Shi-gang FAN

Based on the pre-works, this paper proposed a new short stage process of the intensify aluminothermy reduction by the stage to prepare high titanium ferroalloy with low O and Al contents. We investigated the effects of Al and Ca and Si combination reduction agent, slag type and step-up reduction conditions on the Al content and distribution in the alloy. The results show that the step-up reduction can not only reduce effectively the oxygen content in the alloy, but also reduce effectively Al content. For instance, the oxygen content in high titanium ferroalloy is within 1%~4%, and the Al content is within 1%~5%. Its quality reaches the requirement of high titanium ferroalloy prepared by remelting process.

Jan 1, 2015

By Jorge A. S. Tenorio, Chuanwei Zhuo, Joner O. Alves, Yiannis A. Levendis

"Reduction of combustion-emitted greenhouse gases, which are associated with global warming, may be achieved by use of CO2-neutral alternative fuels, such as bio-ethanol. Distillers Dried Grains with Solubles (DDGS) are the main co-products of the com-grain-based ethanol industries. In 2009, the North American production of ethanol from com was about 38 billion liters, which generated approximately 31.5 million tons of DDGS. Samples of DDGS were pyrolysed at temperatures of 600-1000 °C in a two-stage laminar-flow horizontal furnace, and a catalyst system was used to synthesize nanomaterials. This work presents a microstructural characterization of these nanomaterials by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Results showed that the nanomaterials produced from pyrolysis of DDGS were in the form of long, entangled, rope-like structures with rugged walls, lengths in the tens of microns, and axially non-uniform diameters in the range of 100-300 nm.IntroductionThe interest in ethanol has increased considerably worldwide due to the necessity of finding renewable and cleaner energy resources [1, 2]. According to the Renewable Fuels Association (RF A), the world ethanol production in 2008 was approximately 65.7 billion liters (17.3 billion gallons), which figure represented a 24% increase in the production over that in the previous year [3]. The major producers of ethanol are the USA and Brazil, which together account for 90% of world production. The main feedstock for ethanol in USA is com grain, whereas sugarcane predominates in Brazil [2-4]."

Jan 1, 2011

By Ross W. Smith

Microorganisms are increasingly finding use in mineral processing and hydrometallurgy both for the enhancement of mineral engineering operations and for the remediation of mineral industry wastes. Some of the applications, such as biologically assisted leaching of sulfide ores and biooxidation of refractory sulfide gold ores, are established commercial processes. Others, such as the use of organisms for the removal of heavy metal ions from dilute aqueous streams, are nearing commercial application. Other uses of microorganisms are potentially possible. These include use of microorganisms in leaching non-sulfide ores, the flocculation or flotation of minerals and remediation of toxic chemicals discharged from mineral engineering operations.

Jan 1, 1993

By Regina Krachler, Herbert Ipser

"The principles of the derivation of statistical-thermodynamic models to interpret the compositional variation of thermodynamic properties in non-stoichiometric intermetallic compounds are discussed. Two types of models are distinguished: the Bragg-Williams type, where the total energy of the crystal is taken as the sum of the interaction energies of all nearest-neighbor pairs of atoms, and the Wagner-Schottky type, where the internal energy, the volume, and the vibrational entropy of the crystal are assumed to be linear functions of the numbers of atoms or vacancies on the different sublattices.A Wagner-Schottky type model is used for the description of two examples with different crystal structures:For B'-FeAl (with B2-structure) defect concentrations and their variation with composition are derived from the results of measurements of the aluminum vapor pressure; the resulting values are compared with results of other independent experimental methods.For Rh3~ (with an NiAs-derivative structure) the defect mechanism responsible for nonstoichiometry is worked out by application of a theoretical model to the results of tellurium vapor pressure measurements. In addition it is shown that the shape of the activity curve indicates a certain sequence of superstructures.In principle, there are no limitations to the application of statistical thermodynamics to experimental thermodynamic data as long as these are available with sufficient accuracy, and as long as it is ensured that the distribution of the point defects is truly random, i.e. that there are no aggregates of defects."

Jan 1, 1996

By O. Norman Lotter

There are many scales of innovation in the pursuit of concentrator performance improvement, including paradigm change, inventive change and incremental change. All are important, but the last is low risk, low cost and has a relatively high probability of success, given the right metallurgical skills. Seeking continuous improvement is also essential to ensure that performance does not decline over time due to ore type changes, personnel changes, equipment wear and other factors. When properly implemented, these small gains offer a very high rate of return for the project cost because they are made from marginal, not total, operating costs of the plant. To be effective this approach requires plant trials that use designed structure and appropriate statistics to test the observed differences arising from the old and new process treatments, be they a change in flotation reagent, in grind, pulp density, etc. However the pursuit of small but financially significant performance gains is often regarded as fruitless because of the range of variance in plant data, and the consequent difficulty of ‘proving’ that a benefit has been achieved. Opportunity for improvement is thus sometimes relegated to the realm of the impossible, or at best, treated with skepticism. Operations managers prefer to look for the larger gains, which are easier to demonstrate and prove. Unfortunately, these are seldom to be found; rather, a large gain can be more easily made by executing a series of small recovery improvements that are together equivalent to the ephemeral single large gain. In this paper we advocate a policy of continuing improvement driven by rigorous performance testing protocols and a formal ‘risk analysis’ approach to judging the efficacy of changes implemented in the plant. Following these simple procedures allows rational decisions to be made on the basis of quantifying risk and reward. In particular we consider the choice of hurdle rate for decision-making which best balances risk and reward. It is shown through case studies from actual industrial practice that this approach is practical and delivers significant financial value to the operation.

By Zhengde Pang, Xue-wei Lv, Guibao Qiu, Chenguang Bai, Zhiming Yan

The viscous behavior of molten slags has played an essential role in determining the performance and productivity of the ironmaking process. In this paper, the viscosity and free running temperature in CaO-SiO2-Al2O3-9 mass% MgO-TiO2 slag has been measured at different content of Al2O3 and Al2O3/SiO2 ratio. In addition, the slags viscous activation energy has also been calculated. The results show that the TiO2 as a basic oxide content from 1 to 5 mass% can reduce the viscosity and free running temperature, and moderate content of TiO2 in high alumina blast furnace slag remains effective for reducing viscous activation energy and free running temperature.

Mar 1, 2018