Search Documents

By Patricia Martínez Nicolás

Nickel and ferronickel are some of the major components in the production of special alloys; however, the energy consumption for their production greatly increases their price. A cheaper option could be to use NiO and a reducing agent. This work presents experimental and theoretical analysis to estimate the effect of slag basicity and amount of reducing agents on the NiO reduction from the slag which interacted with molten steel at 1600 °C in an EAF. The slag system contained CaO, SiO2, CaF2 and NiO together with a reducing agent, ferrosilicon or carbon. The NiO content in the slag was 25 mass%. The amounts of the reducing agents (Si and C) were 1 to 4 times the stoichiometric mass to reduce NiO. The CaO/SiO2 ratio was 1.5 and 2.5. The kinetics of the process was very fast since after few minutes the maximum nickel yield was obtained. The slag basicity had a negligible effect on the reduction of NiO.

Jan 1, 2006

By Elli Nurminen

In this work the thermodynamics of the metallic sulphate decomposition reactions were studied through thermodynamical calculations and thermogravimetric methods. The decomposition temperatures and mechanisms were determined for cupric sulphate, ferric sulphate and also for industrial flue dust from a copper flash smelting process. The aim was to determine the thermodynamic conditions for sulphate decomposition and to estimate whether the reactions are kinetically likely to take place in the flash smelting process heat recovery equipment. The information is essential in CFD-modelling of the reactions taking place in the boiler and for optimising the process.

Jan 1, 2006

By Run Huang, Xuewei Lv, Songli Liu, Chenguang Bai

"Titanium alloy was prepared from titania-bearing blast furnace slag (Ti-BF slag) by aluminothermic process in an induction furnace. The effects of aluminum amount on the titanium silicon yield and titanium recovery ratio were studied. The phase transformation and chemical composition of the prepared alloy were investigated by X-ray diffractometry (XRD) and X-ray fluorescence (XRF) respectively. It was found that the mass fraction of silicon and aluminum increased with increasing the aluminum amount, however, the mass fraction of titanium increased first and then decreased with increasing the aluminum amount. Furthermore, both the titanium alloy yield and titanium recovery ratio increased with the increase of aluminum amount. The main phases of the alloy were TixSiy and AlTi3. The titanium alloy samples prepared in various conditions had a composition (wt.%): 38–50% Ti, 29-34% Si, 4-11 Al%, 1.6-2.2 Mn%.IntroductionPanzhihua and Xichang regions in the southwest of China are rich in vanadium-titanium magnetite containing iron, vanadium, titanium and gangue. According to the characteristics of the resource, iron and vanadium are successfully recovered with a blast furnace process and a converter process. However, most content of titanium are entered in the blast furnace slag with TiO2 22% -26% and metallic Fe 2%–6% called Ti-BF slag. Due to the dispersed distribution of Ti in various fine grained mineral phases with a complex combination between Ca, Al and Si, it is difficult to recover the Ti components[1]. This slag is generated at a current rate of 3.6 million tons per year, which adds to the existing 70 million tons of slag produced so far[2]. The slag has had to be piled as large as the mountains, which not only waste of resources but also cause a pollution of the environment. Therefore, the study of integrated utilizing Ti-BF slag has become very significant."

Jan 1, 2012

By Gabriella Tranell

In the manganese ferroalloys industry, there is increasing focus on the performance of different carbonaceous materials within the smelting processes. With a developing scarcity of traditional raw materials, new carbon sources are being identified for potential use in the processes. For this purpose, it is important to be able to predict the suitability of different materials in the process. Hence, the effects of both the physical and chemical properties of the carbon material on the reduction kinetics of manganese and silicon from slag to metal, have been investigated using an advanced sessile drop technique. Using this technique, the reaction patterns of SiO2-MnO containing slag droplets in contact with various solid carbon materials (graphites with different properties as well as cokes and charcoals) at 1400 to 1600\\176;C were studied in-situ. In addition, slag and metal reaction products from kinetic experimental series were analysed. From these results, differences in reactivity between various carbon materials and slags were demonstrated and explained. Mechanisms for both manganese and silicon reduction were proposed.

Jan 1, 2006

By Yunnen Chen

This work concerns the removal of zinc(II) and COD by means of sawdust obtained as a by-product from locally used wood. The zinc(II) and COD removal study has been carried out batchwise where the influence of physico-chemical key parameters such as tree species, pH value of solution, temperature and contacting time and dosage of adsorbent have been considered. The maximum percent removal was attained at pH 9 all for Zn(II) and COD after about 60 min. The adsorbent can be effectively desorption using 0.1 M HCl. The experimental results showed that ion exchange maybe the major adsorption mechanisms for binding the divalent metal ions to the sawdust. Sawdust was a potential adsorbent for the removal of Zn(II) from the effluent of electroplating industry.

Jan 1, 2009

By K. Narayana Swamy

The traditional approach to improving the operating efficiency of a metallurgical plant has been to study individual unit operations and focus on improving the poor-performing unit operations. The complex nature of most metallurgical plants call for a holistic approach that will consider the whole rather than just focus on the individual units of a plant. This holistic approach is part of the systems thinking principles. Numerous case studies highlight the importance of the need to apply systems thinking principles in improving the effectiveness of metallurgical operations. Improving the efficiency of one unit operation without considering its effect on the performance of other unit operations has in many cases lead to lower overall operational efficiency. Modeling and simulation are key to the application of the systems thinking principles. Standard flowsheet models are very useful in scenario analyses though they have to be supplemented with other models for useful predictions.

Jan 1, 2006

By Neil E. Ryan

Because of their chemical reactivity and affinity for oxygen, rare-earth elements are difficult to extract, and due to their close chemical similarity, it is an exacting task to separate one from the other. Nevertheless, these same characteristics can be used to benefit other metals by enhancing their resistance to high-temperture oxidation/corrosion and by inhibiting their corrosion in aqueous environments. This paper gives an overview of the use of rare-earths: [a] as alloy additions, [b] in coatings, and [c] when added to hostile environments, to retard rates of high- temperature oxidation and inhibit aqueous corrosion.

Jan 1, 1992

By P. N. Anyalebechi

The effects of a cross-hatched grooved mold surface topography, casting speed, and superheat on the morphology of solidifying shells of aluminum alloy 3003 have been characterized by a series of immersion tests. The cross-hatched grooves were 0.232 mm deep with wavelength or spacing between 1 mm and 15 mm. The shells solidified at casting speed of less than 10 mm/s on the 1 mm spaced cross-hatched grooved mold surface were fairly uniform with little or no localized variations in thickness. However, the propensity for non-uniform shell growth morphology was exacerbated by an increase in casting speed, melt superheat, and the wavelength of the cross-hatched grooves. This is provisionally attributed to their effects on interfacial heat transfer and wetting of the mold surface by the molten metal.

Jan 1, 2008

By Li Zhang

Air was blown into the molten slag as oxygen resource during the dynamic oxidation. It was found that the oxidation is not only in favour of Ti components into perovskite phase, but also the increase of slag temperature and decrease of slag viscosity during the dynamic oxidation promote the precipitation and growth of perovskite phase, average crystal size of perovskite phase is 48 µm. The experimental result realizes the selective enrichment of Ti components and coarsening of perovskite phase, perovskite phase can be separated by mineral dressing method.

Jan 1, 2009

By Wenming Wang

Recycling of retired cadmium telluride (CdTe) photovoltaic (PV) modules has attracted attention due to new European environmental regulations. Recycling tellurium from CdTe PV modules is becoming more important because of the low availability of this metal. We investigated several treatment paths for reclaiming tellurium from solutions obtained from leaching fragments of CdTe PV modules. Our experiments showed that conventional soda ash neutralization/hydrolysis methods recovered only 50~60% of tellurium. However, by appropriately combining neutralization and sulfide precipitation, almost all the tellurium present in the leaching solution was precipitated and recovered; the concentration of tellurium in the processed solution was reduced from 900-1000 mg/L to less than 1 mg/L, yielding a tellurium recovery greater than 99%. This method can be incorporated in the scheme of recycling spent CdTe PV modules and manufacturing wastes. It may be also an alternative to the current operations for removing tellurium from copper anode slime leaching solutions.

Jan 1, 2006

By Neng-Wen Yu, Shau-Jun Zhu, Ji-He Wei

The desulfurization process by powder injection and blowing in the RH refining of molten steel and its mechanism have been considered and analyzed. Based on the two-resistance mass transfer theory and the mass balance of sulfur in the system, a kinetic model for the process has been developed. The related parameters of the model, including the mass transfer coefficients and the effective amount of powder in the molten steel being treated for desulfurization, have been more reasonably determined. Modeling and predictions of the process of injecting and blowing the lime-based powder flux under assumed operating modes with the different initial contents of sulfur and amounts of powder injected and blown in a RH degasser of 300 t capacity have been carried out using the model. The relevant circulation rate of the liquid steel and the powder injection and blowing rate were taken to be 100 t/min and 150 kg/min, respectively. The initial contents of sulfur in the liquid steel to be treated and the amounts of powder injection and blowing were respectively assumed to be 0.007, 0.006, 0.005, 0.004, 0.003, 0.002 mass-% and 10, 8, 6, 5, 4, 3 kg/t-steel. The total treatment time for desulfurization under each mode was set up at 24 min, equivalent to eight circulation cycles of the liquid steel to be treated. The results indicated that the predictions made with this model are in good agreement with some data of the industrial experiments and practice. Injecting and blowing the lime-based powder flux with the composition of 85 mass-% lime (CaO) + 15 mass-% fluorspar (CaF2) of 3-5 kg/t-steel, it is possible to decrease the sulfur content in the molten steel to ultralow level below (5-10)x10·4 mass-% from (60-80)x 10·4 mass-%. The total treatment time needed will appropriately be 12-20 min. Intensifying the powder injection and blowing operation and increasing the circulation rate of the liquid steel may effectively' raise the rate of the process in RH refining. The model may be expected to offer some useful information and a reliable basis for determining the reasonable process parameters and help in optimizing the technology of desulfurization by powder injection and blowing in the RH refining of molten steel.

Jan 1, 2000

By Christopher Gammons

In developing countries throughout the world, gold ores are being processed by mercury amal-gamation, a technique long banned in the U.S. - unless a retort operation is used for mercury recovery - due to mercury toxicity and its effects on the environment. Amalgamation is a simple process that involves contacting a ground, slurried concentrate or ore with mercury in a slightly agitated vessel, usually for several hours, The amalgamated mercury is separated by gravity and then filtered through a fine cloth to collect the gold amalgam as a sponge, which is then fired to remove the final remnants of mercury and produce high quality gold. However, in Peru and other developing countries in South America and throughout the world, tailings are simply discarded into uncontrolled drainages and ponds and the sponge is fired in the open air. Clearly, in this case, environmental friendly and, to make matters worse, is typically conducted by family members of all ages without proper protection. Furthermore, the technique is inefficient, yielding approximately 50% gold recovery. For the past two years, faculty members from Montana Tech in Butte, MT, USA and the Universidad Nactonal del Altiplano in Puno, Peru have teamed to study the La Rinconada Mine Complex located in southern Peru approximately 100 kilometers north of Lake Titicaca and 25 kilometers west of Bolivia. The mining complex is over 5,000 meters above sea level and exists at the foot of a receding glacier in the Andes Mountains. A suite of soil and water samples collected in 2001 documented extensive Hg contamination in the Rinconada area [1]. The present paper summa¬rizes a follow-up investigation in July-2002, in which water samples were collected at numerous locations along the 200 km length of the Rio Ramis, from the Rinconada mine com¬plex to Lake Titicaca, In addition, we report new results of Hg analyses of fish from Lake Titi¬caca, The results of this study have relevance to safety and health concerns for the miners as well as people in downstream communities.

Jan 1, 2003

By Zhao-feng Xie

A new process of recycling valuable metals containing in the slag of jamesonite smelting in the blast furnace was studied. In this process, the valuable metals such as Pb, Sb, Zn and In etc. were fumed and volatilized and enriched in the dust firstly and then the dust was leached by sulfuric acid. In the leaching procedure, Zn and In in the dust entered into the leaching solution and were separated from Pb and Sb which remained in the residue.The optimal operation conditions of the fuming procedure are as follows: the mass ratio of the blast furnace slag, coal powder and lime are 100:22:10 respectively and the fuming time are 1.5~2.5 h, the fuming temperature is not below 1200C and the volatilization rates of Pb, Sb, Zn and In are 95%, 92%, 86% and 75% respectively. The optimal conditions for the leaching procedure are also presented: the consumption of sulfuric acid is 1.15 times of the theoretical consumption, the ratio of liquid to solid is 4:1 and the leaching temperature, leaching -1time and stirring speed are 90, 1.5h and 300 r?min separately. The leaching rates of Zn and In are 98.5% and 95.2% respectively. The experimental results shows that the valuable metals in the dust can be recovered and separated effectively by this process and the?ir recovery efficiencies are as follows: Pb94%,Sb91%, Zn84% and In69%.

Jan 1, 2009

By Tiebao Yang

In high pressure die casting processes, a die plays a critical role in removing heat from the molten metal during the cavity filling and solidification stages. Proper control of die temperature is essential for producing superior quality components and yielding high production rates. This paper proposes a local temperature control scheme for die thermal management based on a computerized intelligent real-time monitoring and control system (IRMCS). In this scheme, cooling water lines are controlled by a pump and solenoid valves. A controller is designed according to the law of die temperature fluctuations. The results obtained from the experiments carried out on a laboratory die casting process simulator indicate that the controller can limit the local die insert temperatures in a given band. Hence, the desired thermal pattern of the die insert becomes achievable.

Jan 1, 2006

By R. Shimpo

Equilibrium calculations by a computer may sometimes fail in giving solutions when the system includes a large number of components and more than three phases, and especially when no definite information about stable phases is given. An improved method of calculation is presented in which the number of phases need not to be initially fixed, phases can appear or disappear in the course of' calculation and a new method is combined with the Newton-Raphson method to obtain solutions easily. The improved method is applied to the copper smelting operation and all the successive stages of the operation are successfully simulated.

Jan 1, 1983

By Peter Ryan

A patented process for agglomeration of Smelter ESP dusts is described. Addition of suitable binders followed by compaction, transforms fine, difficult to handle material into a dry, flowable agglomerate suitable for plant reentry. Details for the agglomeration process metallurgy and laboratory pilot plant testing are discussed. An example of full scale plant operations is described.

Jan 1, 1999

By A. Deepatana

Bioleaching of nickel laterite ores is based on the use of heterotrophic fungi organisms and their metabolites (organic acids) to dissolve nickel and cobalt from oxide minerals to form metal-organic complexes. Metal recovery from this process using an aminophosphonic acid based chelating resin (Purolite S950) was investigated as a function of metal concentrations, complexing agent including citric, dL-malic and lactic acids. Batch adsorptions were conducted using synthetic leachate solutions of nickel and cobalt with concentrations from 15 to 2000 mg/L prepared in 0.01 and 0.1 M organic acids. Adsorption equilibrium data were interpreted using the Langmuir, Freundlich and Dubinin-Kagner-Radushkevich (DKR) models. The results showed that equilibrium adsorption data for nickel-organic complexes followed the Freundlich model and those for cobalt agreed with the Langmuir model. It was observed that the maximum adsorption capacities of nickel and cobalt were 3.26 and 10.48 mg/g resins respectively. These were achieved in metal complexes prepared from 0.01 M lactic acid. Metal elution was conducted using 2 M nitric acid. High metal recoveries were achieved from low metal concentrations but were found to decrease with increasing metal concentration. The results suggest that effective recovery of nickel and cobalt from low concentration of metals, such as those generated from bioleaching operations, can be achieved suitably using chelating resins.

Jan 1, 2006

By B. B. Agrawal

Iron ore fines is an area of concern in India. A possible avenue is to use these fines for sponge ironmaking. Work has been carried out to pelletize these fines with coal and a suitable binder, and cure them in ambient atmosphere to retain in-situ reductant. Pellets were characterized for physical strength and metallisation. Critical factors were granulometry was percentage of coal & binder. In laboratory tests, pellets got metallized faster compared to lump ore. Large-scale trials were conducted in a 12-meter long rotary kiln plant. For 90% metallization, required residence time was only 60 minutes against 240 minutes for lump ore. Coal requirement also decreased. Investigations established the fast reduction nature of pellets. This is due to reduction-reactions occurring simultaneously at many sited within the composite pellets, in addition to the diffusion of reducing gases from the surface of the pellets to its core. The developed process is a value addition in the conventional pelletmaking and is environment-friendly also.

Jan 1, 2006

By R. Elliott, H. Bayati

"Effect of time and temperature on microstructure and mechanical properties of an austempered ductile iron, ADI, of composition 3.6%C, 2.6%Si, 0.4%Cu, 0.2%Mn are reported. Xray analysis and. microstructural observations indicate that lowering the working temperature, aging temperature, increases the lifetime of ADI significantly. Results show· that lowering the aging temperature increases the strength and reduces the ductility of ADI. DSC traces for ADI austempered at 340°C are presented. Comparison of the DSC analysis and kinetic measurements demonstrates that the DSC traces can be· used to predict the life time of ADI successfully.IntroductionAustempered ductile iron, ADI, is one of the most significant developments in cast iron technology over the past two decades. Outstanding properties of high yield, ultimate strength, ductility, fatigue and wear· resistance make ADI suitable for a range of applications including gears, connecting rods, crankshafts and agriculture machine components. The austempering reaction in cast iron occurs in two stages, Fig. I, in contrast to the single stage reaction in steel. In stage I the relatively low carbon austenite produced during austenitising transforms into ferritic plates and high carbon austenite, a metastable structure called·ausferrite. The high carbon ailstenite and supersaturated ferrite produced in stage I decompose into ferrite and carbide in stage II: to form a structure similar to the bainitic structure in steel. This behaviour exposes a well-defined processing window, t1 - t2, over which the maximum amount of ausferrite is produced, Figure 1. Whereas the bainitic structure determines the properties of austempered steel, ADI properties are mainly affected by volume fraction of retained austenite (VRA), austenite carbon content (ACC), unreacted or martensite volume fraction (UA V), compositiori and amount of carbides, and morphology of ferritic plates[l,2]. Due to the detrimental .effect of martensite and carbides on properties of ADI, an ideal structure of ADI consists only of ausferrite [l,2]. Thus, it is common to determine the processing window for each austempering treatment in order to identify the optimized austempering time. Decomposition of austenite (stage II) signals the end of the life time for an ADI component, therefore, the aging behaviour of ADI at different working conditions can be studied by determining the t2."

Jan 1, 2000

By Vinay Kumar

The disposal of large quantities of electronic scraps generated world wide is causing not only environmental problem but also loss of resources. Therefore, R & D efforts have been made to develop a suitable process for extraction and separation of metals viz. copper, zinc, cadmium and nickel expected from the leaching of e-scraps using solvent extraction process. Different process parameters viz. pH, aqueous to organic ratio, kinetics of extraction, extraction isotherm to establish stage requirement for extraction in continuous mode etc have been studied to optimise the condition for the separation of metals. The studies showed the selective extraction of copper after iron precipitation from the sulfuric acid leach solution of e- wastes containing ~1.0 g/L Cu and minor impurities with 2-hydroxy-5- nonylacetophenoneoxime (LIX 84) above pH 2.0 in single stage. A scheme for separation of cadmium, zinc and nickel has been proposed using di(2-ethylhexyl) phosphoric acid (D2EHPA) under controlled pH of the aqueous solution. The order of extraction was found to be Zn> Cd> Ni.

Jan 1, 2009