Search Documents

By M. K. Larson

The U.S. Bureau of Mines and Cyprus Shoshone Coal Corp. conducted a study of deformation mechanisms around a longwall gate-road system in an underground coal mine. Of particular interest was roof deformation over the headgate entry. The strata above and below the coal seam are very weak, carbonaceous mudstones that have planes of weakness oriented along the bedding. Visual observations of previous gate roads over several years suggested that deformation was time dependent and resulted in creep along joints or crack growth. Instruments were installed at a test site to measure deformation around the entry, strew changes in the pillar, and loads transferred to support systems. Multipoint extensometers, instrumented bolts, instrumented trusses, biaxial stressmeters, borehole pressure cells, and single-point extensometers were installed. Monitoring continued until the longwall face passed the test site by 38.7 m (127 ft). Results show that fracture zones arched over the entry from both ribs, most bolts and trusses were loaded past their yield point, and the largest change in secondary principal stress was almost horizontal in the pillar. Displacement measurements in the roof showed classic primary creep.

Jan 1, 1995

By Chris Adams

The application of pre-tensioned tendon roof support assisted Harworth Colliery in their revival, from impending closure to lowest cost deep-mined producer in the UK, over just six months last year. The paper describes this success story, how it came about, the reasons "why", and the method "how"

Jan 1, 2003

By Stanislaw Prusek

The present state of Czech and Polish coal mining industry is presented at the beginning of the article. This paper will inform the reader of the general data concerning hard coal reserves? number of mines, number of miners, output, number of longwalls, productivity, depth of extraction, and extraction methods?in both countries. The main part of the paper describes the methods of gateroad development as well as gateroad support characteristics (support types, gateroad shape and dimensions, distance between support sets, types of reinforcements). The development prospects of gateroad support in the Czech and Polish coal mining industry are also presented.

Jan 1, 2011

By Daniel W. H. Su

This paper presents the results of an extensive geomechanical testing and monitoring program conducted at a longwall panel. The field program included the monitoring of roof caving sequence and mechanism, surface subsidence, change of pillar stress, roof displacement and entry convergence, and strength characterization of the overburden rocks. The response of eight headgate pillars and the adjacent entries was monitored as the longwall face approached and passed the instrumented locations. Overburden response to longwall mining was monitored using time domain reflectometry (TDR) technology; and, the height of the highly fractured zone above the gob was determined by postmining drilling. Good correlation was found between the height of the highly-fractured zone and the TDR, subsidence, and pillar stress data. The results provide a detailed picture of the response of overburden strata and chain pillars to longwall mining. A preliminary model representing the overburden strata behavior at the test site in response to the longwall mining is proposed.

Jan 1, 1987

By Stanley J. Michalek

Good planning is critical to operating a safe and efficient mining operation. As the shallow coal scams become depleted, attention turns toward deeper mineable seams or remnant coal reserves. It is becoming more common to place a mine in a scam that is below or adjacent to existing mine workings. Significant research has been conducted regarding the ground control issues of multiple scam mining. However, safety aspects of the operation may not be fully considered. Safety issues include working below or adjacent to a flooded mine and controlling gas Communication between the active mine and the nearby mine. This paper will discuss the safety issues a mine operator should consider when working under or adjacent to mines that may be flooded with water.

Jan 1, 2000

By Linsheng Xu

When coal seam is under the integral thick sandstone (or conglomerate), the structure of thick sandstone is integral and its strength is rather high. After coal is extracted, the roof is hanging and caving is difficult. When the method of full caving is adopted in the longwall working face to control this kind of hard and difficult caving roof, the effect of roof-controlling affects directly the production and safety. In China Datong Coal Mines the extracting coal deposit is Datong Jurassic period. Most of the roof is sandstone and conglomerate. It is hard and difficult to cave. Having used special hydraulic power supports and other special ways to deal with the roof, the hard and difficult caving roof has been controlled.

Jan 1, 1986

By Ross Seedaman

The specification of roof support needs to consider rock strength, imposed ground stresses, and more importantly the bedding and joint structure of the immediate roof rocks. A database structure has been developed that allows these considerations to be incorporated into modern mine planning software so that better predictions of mining rates can be made. Rock strength is estimated from core and/or geophysical logs (especially the sonic velocity log) and ground stresses are estimated from depth of cover and knowledge of the regional stress field. The database is unique in the way it addresses bedding structure. Only 10 roof lithologies are allowed and these are allocated a numerical value that reflects an increase in the average spacing of bedding partings. These are referred to as 'Geotechnical Ferm Units' (GFU). The locations of all bedding discontinuities logged in the core are entered into the database and referenced to the GFUs. It has been found that, within each GFU, bedding spacing follows a negative exponential distribution and so it is a simple matter to predict the probability of the occurrence of any roof beam thickness. Output from the database can include plans of roof strength, the onset of overstressing, and the statistics of the distribution of beam thickness in the immediate roof.

Jan 1, 2003

By Kikuo Matsui

Standing supports such as steel arches or square work supports along with the necessary struts and lagging have been traditionally employed in the longwall gateroads of the Japanese underground coal mines. Miike Colliery has newly introduced the interpanel-pillar mining system and the strata bolting system in gateroads to raise productivity levels and reduce operating costs. The Department of Mining Engineering, Kyushu University, in cooperation with the Miike Colliery and the Coal Mining Research Center, Japan (CMRCJ), has been conducting research into the optimum design of strata bolting as a primary support system in longwall gateroads. This paper presents a brief overview of the current state of strata bolting technique being applied in longwall gateroads at the Miike Colliery and discusses some problems in employing bolting.

Jan 1, 1993

By Russell Frith

The paper defines the various operational advantages associated with the use of cribless tailgates during longwall extraction and considers the associated ground control issues that need evaluating to ensure a successful outcome. Reference is made to longwall mines in Australia currently using cribless tailgates and the geotechnical and ground support factors that allow them to do so This includes the nature and behaviour of the roadway roof the stability of the chain pillar and also the type and timing of installed support A specific case history from a colliery in NSW will he referred to whereby heavy standing support was replaced with lower density tensioned cables as routine TV secondary support, which resulted in both improved TG roof conditions and a significant cost reduction. The conclusion will be drawn that cribless tailgate roadways can potentially he used in many environments either due to the existence of highly competent immediate roof conditions or through the appropriate application of active reinforcing support measures in less competent conditions. Use will he made of Strata Engineering?s roof behaviour and stability model in demonstrating the various concepts involved.

Jan 1, 2000

By Jisheng Han

Interaction effect exists when two or more neighboring seams are mined. The mining activity in one seam causes stress redistribution and strata movement in both the roof and floor. When the thickness of interburden between two neighboring seams is small, some hazardous situations like roof cutters, roof falls, floor heave and rib spalling in one seam may be encountered due to the effect of the mining activity in the other seam. An investigation about roof cutters, roof falls and floor heave was conducted in a West Virginia mine to study the interaction of multi-seam mining. The mine is mining the Sewickley Seam, which is about 90 ft above the Pittsburgh Seam which was mined in the 1960's using room and pillar method. The roof falls and other stability anomalies of entries observed underground in the Sewickley Seam were found closely related to the location of barrier pillars and gas well pillars left in the Pittsburgh Seam. Then numerical modeling was carried out to check the interaction between these two seams of mining. It was found through the modeling results that in the areas where pillaring operation was conducted in the Pittsburgh Seam, the stress concentrated less in the Sewickley Seam while near the edge of the gas well pillars and barrier pillars, high stress concentration was observed. It was concluded that under the geological conditions of the study mine, the entries stability would be affected by the lower seam mining activity, especially above or around the edges of pillars.

Jan 1, 2005

By André C. Zingano

The domino effect in a violent pillar collapse occurs due to the redistribution of stress in the remaining pillars near the collapse, and this stress transfer occurs in the immediate and main roofs. The remaining pillars do not have enough load capacity to support this overstress and also fail, and the domino effect propagates further to the entire panel. The domino effect does not occur only due to low load capacity of the pillars, but also the roof rock mass quality, because the stress is transferred by the roof. In high competent roof without discontinuity (fault), like massive sandstone seam, the deformation of the roof is the cause of pillar collapse extension and propagation. Depending on how close it is approaching the collapse limit; the immediate and main roofs behave differently. When it is close to the collapse limit roof convergence and pillars compression occur. Conversely when it is far from the collapse limit divergence and pillars decompression occur. This is called the arc-effect. This paper studies this behavior of the roof (immediate and main roofs) using numerical modeling to simulate the roof deformation and stress distribution in the roof and pillars. This simulation represents the progression of pillar collapse and shows the zone of convergence and divergence of the roof, and also the effect of this behavior on pillar confinement. Two-dimensional plain strain model was applied to simulate the arc-effect. The simulation results were compared to those of the instrumentation that was installed before the collapse. Keywords: pillar collapse, room and pillar, numerical modeling

Jan 1, 2005

By Hamid R. Nikraz

This paper reports the finding of a comprehensive investigation carried out to evaluate the compaction characteristics of saturated sandstone aquifers in the Collie Coal Basin under conditions anticipated during dewatering operations. A triaxial technique has been adapted to evaluate the compaction characteristics of the sandstone aquifer in the Collie Basin. This technique, which allows the strata stress regime to be reproduced by triaxial loading with zero lateral strain, also provides a precise evaluation of lateral stresses and consequently Poisson's ratio under in situ conditions. The paper contains a description of the equipment commissioned, test techniques, results, analysis and interpretation of the data obtained. The testing evaluation techniques are general in nature and can be applied to field situations in locations where similar weak sandstones occur.

Jan 1, 1993

By Kewal K. Kohli

An investigation was performed to determine the sequence of events which caused the 1987 surface subsidence and related damage to several homes in Walker County, Alabama, USA (see Figure 1). Surface affects compared to mine maps indicated the subsidence to be mine related. However, two coal seams had been worked under this area. The upper seam, the American seam ranged from 250 to 280 feet beneath the surface in the area in question. It was mined-out before 1955 by room-and-pillar method leaving in place narrow-long pillars to support the overburden strata, and abandoned in 1955. The lower seam, the Mary Lee seam, ranged from 650 to 700 feet beneath the surface. The Mary Lee seam had been abandoned in 1966 and subsequently became flooded. The dewatering of the Mary Lee seam workings in 1986 caused the submerged pillars to be exposed to the atmosphere. Due to multiple seam mining and the fact that workings had been inundated then dewatered, a subsurface investigation ensued to determine the sequence and ultimate cause of surface subsidence. Core sample tests with fracture analysis in conjunction with "down-the-hole" TV camera inspections provided necessary information to determine that the subsidence started in the lower seam and progressed through the upper coal seam to the surface. Evidence from the investigation program established that dewatering of the lower seam workings caused the marginally stable support pillars and the roof to collapse. This failure triggered additional subsidence in the upper seam which broadened the area of the influence at the surface.

Jan 1, 1992

By Song Guo

This paper will present the roof bolting finite element model developed at Jennmat Corporation used to study the control mechanism of the tensioned bolt system in the laminated roof with a large horizontal stress. In addition, it will discuss general support concepts pertaining to the tensioned bolt system which are derived 6om a series of studies in conjunction with the authors' working experience and extensive research efforts over the years.

Jan 1, 1997

By George J. Karabin

Since the inception of a qualitative pressure arch theory by Haak4 in 1911, much work has been done in an effort to apply this concept to underground mining. It has been used in both longwall and room and pillar mining to determine roadway and pillar stability (with varying degrees of success). This paper presents a summary of a case study where the pressure arch concept was extended in a totally qualitative manner to define the source of roof control problems in the mains of a Pennsylvania mine. It was concluded that, due to the method of mining employed, a pressure arch formed over a portion of the entries, and the high abutment stresses accompanying it resulted in extreme roof deterioration. The following discussion will include a general presentation of the arching mechanism, the physical response of the roof strata under mining-induced abutment stresses (both from the case study and in general), a computer simulation of ground stability under both "normal" and "abutment" stress conditions, and finally, potential means of alleviating such conditions.

Jan 1, 1982

By Michael A. Berdine

In early 1997, Twentymile Coal Company took a dramatic departure from traditional longwall recovery methods. Previously, Twentymile's standard longwall meshing procedure included the use of chain link fencing material. Beginning with the 9-Right to 8-Right longwall recovery operation, Twentymile incorporated a polyester geogrid mesh system supplied by DYWIDAG-Systems International. This paper discusses the subsequent utilization of the polyester geogrid mesh system at Twentymile.

Jan 1, 2001

By Joachim Leonhardt

Hundreds ofbolt-indicators were already used successfully in the German deep hard coal-mines to increase the safety and economy. The bolt-indicator offers the simple possibility to show roof-bolt (anchor-) loads. to indicate weak points as well as to optimize the anchor density and the dimension: The bolt-indicator is mushroom shaped and consists of coated metal. It is inserted between the anchor plate and the flanged nut. The loads appearing at the anchor are transferred to the bolt- indicator and can be recognized visually at the cylindrical part by the amount of the surface coating. Examples are used to clarify the application aims, operation and usage of the bolt-indicator and its yielding advantages in practice.

Jan 1, 2001

By Axel Preusse

This paper shows basic considerations about the prognosis and prediction of surface subsidence and other ground movements in the German hardcoal industry. The following case studies describe experiences collected in projects between university and industry.

Jan 1, 2000

By Frank Kendorski

Several startup or longtime underground stone mines have experienced unanticipated roof control difficulties due to the variable geologic character of the roof strata. Careful mapping of roof conditions, and identification of controlling geologic and mine geometric factors using sedimentological descriptors, lead to an understanding of the mechanisms causing roof problems. Types of bedding plane features can be categorized into geometric, internal structures, bedding-plane markings, deformed bedding, solution structures, and accretionary structures. Factors such as encountering open water-filled master joints; roof strata delamination due to internal water pressures; local karst features with mud, sand, and water hazards; and sudden loss of limestone roof due to paleo-channel erosion are some recent problems described.

Jan 1, 2002

Retreat longwall method with re-use of gateroad has been traditionally employed in Japan, mainly because of the advantage of higher recovery. But the Miike Colliery has newly introduced the interpanel-pillar system to maximize the production efficiency. The Department of Mining, Kyushu University, in cooperation with the Miike Colliery and the Coal Mining Research Center (CMRC), has conducted research into the optimum design of interpanel-pillar, because this system may be adopted in other coal mines as well. Field measurements of the deformation of the gateroads and of stress distribution in the pillar show that the designed layout of the panel and pillar and the supporting system are proper from the viewpoints of gateroad maintenance and spontaneous combustion in the pillar.

Jan 1, 1990