Search Documents

By Deno M. Pappas

The purpose of this U.S. Bureau of Mines study was to determine the material stiffness properties of the gob for use in numerical models of rock mass response to longwall mining. Photographs of actual mine gob were used to approximate particle size gradations of gob material. The gradation curve was shifted down to a laboratory scale, and 20 uniaxial compression tests were conducted on simulated gob material from 3 different rock types. The study found that the nonlinear stress-strain curves obtained from the three materials were similar, and could be represented in terms of moduli as follows: Es = 2.36s + 1,360 (1) Et = 0.00181s2 + 9.33s + 294 (2) where Es = secant modulus, psi Et = tangent modulus, psi and, s = stress level (due to overburden), psi. These curves correlated well with the theoretical solution curves developed by Salamon. Other effects on gob behavior were attributable to these studied factors including void ratio, thickness-to-width shape ratio, and rock compressive strength. The generated equations should provide numerical modelers with a practical means of estimating gob modulus as a function of stress level.

Jan 1, 1993

By Timothy J. Matthews, Timothy J. Batchler, Ted M. Klemetti

"From 2011–2016, there were 1,511 documented injuries, including 7 fatalities, from ground falls in underground coal mines in the United States. The majority of these ground-fall injuries were not caused by a major roof collapse, but from falls of smaller rocks from the immediate roof. Roof screen can significantly reduce the number of these injuries and has been widely used in underground coal mines for surface control. Because of the potential of reducing ground-fall injuries, the National Institute for Occupational Safety and Health (NIOSH) is further evaluating the performance characteristics of welded wire screen as used in underground coal mines by conducting a laboratory testing program using the Mine Roof Simulator (MRS) in Pittsburgh, PA.The load-displacement characteristics of an 8-ft x 12-ft panel of 8-gauge welded screen were evaluated using a newly designed, large laboratory screen test frame with multiple load pull locations. This screen was tested in a configuration that simulates current installation practices in U.S. coal mines. In this study, the effects of varying the number and position of the load pull location on the screen performance were evaluated. Ultimately, the type of information obtained in this and similar studies can be used to aid in developing wire roof screen design criteria and to assist mine operators in the selection and use of roof screen in underground mines.INTRODUCTIONThe large majority of ground-fall injuries are caused by falls of smaller rocks from the immediate roof. Various controls are currently being used in mines to control this surface rock, including the use of wire roof screen. In mines where wire roof screen has been installed, injuries from rock falls have been reduced dramatically (Robertson and Hinshaw, 2001). Roof screen has the potential to prevent hundreds of injuries caused by the fall of small rocks between permanent roof supports (Compton et al., 2007). Because of this potential for reducing ground-fall injuries, the National Institute for Occupational Safety and Health (NIOSH) is evaluating the performance characteristics of welded wire screen as used in underground coal mines by conducting a laboratory testing program in the Mine Roof Simulator (MRS) in Pittsburgh, PA."

Jan 1, 2018

By Brian Daniels, James Farroni

"Draw rock (small rock that forms/falls when bolting the roof and/or rib) is the cause of numerous injuries annually. These injuries result in lost work hours and low morale. The report below explains how ""Mine Safe Draw Rock Shields"" (Pans) are used in an underground operation. This report will chronicle the application of these pans in a Southern West Virginia coal mine along with testing data that measures their effectiveness. Since the introduction of these pans in 2002 the amount of reportable accidents relating to draw rock has decreased by 80%. The report below reinforces that perimeter contact is critical to the performance of these pans. In addition the strength of these products at the perimeter will determine their effectiveness. The results of the testing data outlined in this paper, along with the physical records at the study mine, confirm that the use of pans has significantly reduced draw rock falls at this facility.BACKGROUNDSupplemental support is defined as ground control that is used in addition to required support in an underground mine. Some examples of supplemental support are:• Pans• Mesh/Geogrid• Mats• Half Headers• Boards• ChannelA typical roof condition that warrants the use of pans is when loose small rock is dislodged while bolting. If the top is very scaly (loose, thin rock) additional supplemental support can be used in conjunction with pans such as mesh or geogrid (See Figure 1). Pans will provide protection where used and approximately 12 in (250 mm) out from perimeter. This is achieved by contact with a surface which will put scale in tension up to 12 in (250 mm) from perimeter of pan.INTRODUCTIONThe ease of applying a roof support system is critical to effectively operating a deep mine. Figure 2 shows how a pan is installed in conjunction with a roof bolt and bearing plate. The Mine Safety and Health Administration (MSHA) requires that supplemental support cannot decrease the performance of required support. The goal of using all supplemental support is to provide additional safety for the miner which equates to increased productivity.The ability of skin control products to contact a surface is the single most critical characteristic (Figure 3 and Figure 4). If the material does not contact the surface it cannot be effective. Therefore, the flexibility, design and proper installation of the products are critical in determining their effectiveness. Figure 5 shows the proper installation of the roof pan.To reiterate, all skin control must be applied in conjunction with a roof bolt and ASTM approved bearing plate as shown in Figure 4."

Jan 1, 2010

Results of direct shear tests on rock discontinuities and triaxial compression tests on intact rocks are presented and - discussed. The main parameters considered area stress functions, angle of internal friction and cohesion variations. Primary objective of this work is to determine relationships that adequately describe the rock behaviour for design of mining excavations, while still maintaining a certain degree of simplicity.

Jan 1, 1987

By Larry Howe

Second, or retreat mhng with Mobile Roof Supports (MRS) has now been part of coal mining in the United States for a decade Their utilization has evolved into mining applications which vary in seam heights from 38 inches to 170 inches, and overburden depths from outcrop to beyond 1200 feet This paper will detail the pillaring plans, lift sequences, and mnchky utilized in these operations and the rational for the plans A comparison of the current productivities achieved will be outlined

Jan 1, 1998

By Dion Pastars

Kestrel Coal has undertaken a surface-to-seam consolidation program of faulted ground prior to longwall retreat in the 304 panel. Micro fine cement is used to improve the rock mass quality and therefore reduce the risk to personnel and equipment whilst increasing previously assumed sterilised reserves. The program is based on information attained from previously successful grouting campaigns in the Queensland coal area and follows the decision making process to ensure there is sufficient spatial permeation of cement across the faulted area. This data is used to assess the residual risk to the business in terms of health, safety and production

Jan 1, 2007

By Jimin Su, Enguang Zhu, Kangning Zhang, Yang Li

"The effect of interburden on overlying strata movement during the mining of a lower group coal seam is still a challenge in China. Based on the multiple coal seams in western China, numerical simulation and field tests are applied to study the interburden and overburden movement during the undermining process. This study focuses on the impact of the thickness and structure of the interburden, the proportion of hard rock, and the ratio of the overburden thickness to interburden thickness (OB/IB). In this paper, four typical underground coal mines are simulated for lower seam longwall mining with different interburden parameters. The results indicate that the ratio of the overburden thickness to the interburden thickness is not the dominant actor for multiple seam longwall mining, especially in the mines in western China,which feature shallow depth. The thick and hard interburden could strongly affect the lower coal seam mining process. INTRODUCTION The project background is based on four typical underground coal mines in western China.The information on the overburden and interburden is shown in Table 1. Different overburden to interburden thickness (OB/IB) (Ellenberger, 2009) values of the four coal mines are also studied: 6.2 in Bulianta coal mine, 7.2 in Kaida coal mine, 8.2 in Shigetai coal mine, and 9.4 in Halagou coal mine. The proportions of hard rock in the interburden of the four coal mines are also different: 0% in Kaida coal mine, 70% in Shigetai coal mine, 80% in Bulianta coal mine, and 100% in Halagou coal mine. To be specific: the thickness of interburden are listed as follows: 7m in Halagou coal mine, 6m in Kaida coal mine, 10m in Shigetai coal mine, 28m in Bulianta coal mine. The depth of the upper coal seam are: 66m in Halagou coal mine, 54m in Kaida coal mine, 79m in Shigetai coal mine, 182m in Bulianta coal mine. NUMERICAL SIMULATION UDEC 4.0 is applied in this paper to analyse the overlying strata movement and the interburden failure.(Liu, 2007) This is based on mining in the lower coal seam under the mined-out upper coal seam (Majdi, 2012, Morsy, 2006)."

Jan 1, 2017

By Liu Xiao, Lin Xiaoying, Ma Geng, Tao Yunqi

"The soft coal in China has several issues, low permeability, high gas content and prone to gas outburst, making it difficult to drill and improve its permeability. Using the rock mass loading test, the relationship of stress-strain-permeability-time of sandstone was investigated. The fracture network that communicates with coal seams to provide the pathways for gas migration can be established by drilling, hydraulic fracturing or loose blasting in the roof and floor about 5m from coal seams top and bottom. The gas migration can be summed up as ""desorption-diffusion-two levels of seepage"" for gas drainage of the quasi-protection-layer in hard coal seams, and ""desorption-two levels of diffusion-seepage"" in soft coal seams. In the quasi-protection-layer, different gas drainage techniques were used during different stages of mining. Gas drainage of the quasi-protection-layers was demonstrated at Hebi Zhongtai Mining Co., Ltd. The results showed that the technique promotes the gas seepage flow, and improves the efficiency of drainage. The influence zone of the quasi-protection-layer was 1601 m2 and the average amount of gas drainage was 328m3/d, with the maximum being 661m3/d. INTRODUCTIONGas is one of the main factors that cause disasters and influence safety production in underground coal mines (SACMS, 2009). The coal-bearing formations in China have been subjected to multiphase tectonic stress field during the period of geological evolution. Coal body was often crushed into fragmented coals and mylonitic coals under the tectonic stresses (Su and Lin, 2009). The gas permeability of coal is generally poor. So in underground, drilling and hydro-fracturing technology have been used to improve the permeability of coal, such as intensive drilling, hydraulic punching, hydraulic cutting, hydraulic extrusion and deep hole blasting. But the gas drainage rate was low, only 23% (Liu, Li, and Li, 2006; Li and Wei, 2006; Henan Polytechnic University, 2008; Ma, et al., 2014; Lin and Wu, 2009; Zhou, et al., 2011) that was much lower than the rates achieved in the main coal-producing countries such as America and Australia whose average rate of gas drainage was 50%. The protection layer mining technology has been used widely as an effective technique to improve the permeability of coal in the mining of multiple coal seams (Cheng and Yu, 2003; Diaz and Gonzalez, 2007; Karacan, et al., 2007; Palchik, 2003; Latham, et al., 2013; Yuan, et al., 2013; Shi and Liu, 2007; Wang, et al., 2008, Guo, et al., 2015; Lu, et al., 2015; Slazak, Obracaj, and Swolkien, 2014 ). In the single low permeability coal seam, there is no protection layer. This kind of coal seam has low permeability, high gas content, soft coal body, and is prone to serious gas outbursts. During drilling, the holes very often spray, collapse, stuck and wedged the drilling tool. The hole length drilled is difficult to reach the required minimum, the service life of holes for gas drainage is short, the construction cost is high, and the holes are difficult to maintain. The gas drainage efficiency of single low permeability coal seam, especially soft coal seams, cannot be improved even though hydro-fracture technology has been implemented, because its permeability is not improved."

Jan 1, 2016

By Xuexin Ding, Weijie Wei, Jinwang Zhang, Yi Chen, Shengli Yang

"Many ultra-thick coal seams exist in Xinjiang and the northern part of the Inner Mongolia. These coal seams are more than 30-40m thick. This kind of the thick coal seam is too difficult to extract in one slice, so the top-coal caving longwall mining method was designed for this purpose. In order to study the movement characteristics of the overburden strata and the development of the ""three zones"" in ultra-thick coal seams, the physical and numerical simulations were carried out based on the in-site condition of Baiyinhua coal mine. The result shows that, when extracting the upper part of the l 5m thick coal seams, the first weighting interval was 50-58m and the periodic weighting interval was I 8-20m. The caving zone, fractured zone and bending and sinking zone were 38m, 92m, and 50m respectively in height. The fractured zone height increased with the advancing distance of the face, but in some localities, a ladder-like distribution due to the periodic weighting existed. When extracting the lower part of the 25m thick coal seams, the roof was extremely broken and the collapse range of overlying strata continued to increase in irregular form.INTRODUCTIONThe thick coal seams occupy 44 percent of coal reserves in China and account for 45 percent of the gross domestic coal production. There are three main methods for extracting the thick coal seams: sublevel mining, large height mining, and longwall top-coal caving (LTCC) (Wang, 2009). Due to the rapid development of LTCC in the past two decades, it has become the most extensively used mining method. It possesses the advantages of high-production, high-efficiency, low development ratio, and low-cost (Yang, Zhang, Chen, and Zhengyang, 2016; Wang and Zhang, 2015). Baiyinhua coal mine's coal reserves are full of uniformly distributed thick coal seams, with the minable thickness of the main coal seam between 25 to 40m, i.e. the main coal seam is an ultra-thick coal seam. Sublevel longwall top-coal caving (SLTCC) which is an efficient method for extracting the ultrathick coal seams has led to multiple disturbances Xie, Chen, and Wang, 1999; Singh and Singh, 1999; Xie, Chang, and Yang, 2009. Therefore, using the case of Baiyinhua coal mine, the movement features of overburden strata and development characteristics of the three zones in ultra-thick coal seams were studied by physical and numerical simulations (Qian, et al, 2003; Qian, 1994)."

Jan 1, 2016

By Chase K. Barnard, Rahul Thareja, Sean Warren, Rajagopala Kallu

"Inflatable rock bolts are commonly utilized for ground support in Nevada underground mines, however, there is limited information regarding what factors influence the bond strength of these bolts. Bond strength is an important parameter in friction bolt support design, and this information is usually not available from manufacturers as a standard. Previous research has investigated the bond strength of friction bolts; however, these studies focused primarily on split set bolts and ground conditions more favorable compared to those commonly encountered in Nevada underground mines. Without site-specific bolt pull-out tests, ground control engineers are required to make assumptions regarding the in-situ bond strength of rock bolts. This is especially a concern for projects in the feasibility and initial development stages before site-specific experience is acquired.The purpose of this paper is to establish confidence in anticipated minimum bond strength for inflatable rock bolts by comparing the bond strength to variable geotechnical conditions using the Rock Mass Rating (RMR) system. To investigate a correlation between these parameters, the minimum bond strength of pull-out tested inflatable rock bolts was compared to the RMR of the rock in which these bolts were placed. Bond strength vs. RMR plots indicate that expected minimum bond strength is positively correlated with RMR, however the correlation is not strong. Cumulative percent graphs indicate that 97% of pull-out tests result in a minimum bond strength of 1 ton/ft and ½ ton/ft in RMR =45 and <45, respectively.Although lower bond strengths are more commonly encountered in low RMR ground, high bond strengths are possible as well, yielding higher variability in bond strengths in low RMR ground. Bond strength of friction bolts relies on contact between the rock bolt and drill hole. Experience in Nevada indicates that RMR is known to affect both the quality and consistency of drill holes which likely affects bond strength. Drilling and bolting in low RMR ground is more sensitive to drilling and bolting practices, and strategies for maximizing bond strength in these conditions are discussed."

Jan 1, 2015

By K. Y. Haramy

Rock burst and coal mine bump research using static and dynamic rock mechanics instrumentation has been conducted for several decades. Research efforts typically have been conducted using static instrumentation such as pressure cells, convergence measurements, multipoint borehole extensometers, and shield loading pressure measurements; dynamic rock mechanics instrumentation, for example, microseismic monitoring, has been used to help provide precursors to those violent failures. Unfortunately, these different styles of study have never been used in tandem. We report in this study the unique opportunity to have both static and dynamic instrumentation available for monitoring a longwall panel in a deep western coal mine and show that the two methods used in tandem provide information to understand the causes of a major bump. Several static rock mechanics instrumentation sites were carefully chosen along the longwall panel in the coal seam, packwalls, roof, and floor to provide the stress history during mining, including the stress redistribution that occurred before and after the major failures. Monitoring of the shield pressure on selected shields of the longwall face revealed that the cyclical loading anticipated during normal caving processes was not occurring. In addition, by locating each microseismic event (rock noise), the areas that were not adjusting to the changing stress field were clearly delineated by a lack of microseismic activity. The area of the longwall panel that did not adjust to the changing conditions ultimately failed. The combination of static and dynamic rock mechanics instrumentation data analysis provided the necessary information to determine the interaction of the structural members and the cause of the major failures at this mine.

Jan 1, 1988

By Antoni Kidybinski

Coal mining both with longwall and room-and-pillar method often encounters severe operational difficulties due to had roof conditions. Rooffalls at entry cross-cuts or along the rib line in longwalls as welt as dynamic and excessive loads on supports due to overhanging of strong roof layers in a goab - are well known phenomena to the mine operators. Also, a number of practical examples may be quoted of dramatic improvement of working conditions after changing of coal winning technology or supports type. It is therefore a question to be answered how far we are able to recognize roof strata properties before mining starts and adjust both coal extraction technology and supports of entries to rock stability foreseen. Furthermore, engineering principles and criteria for decision making should be established. In recent years several in situ rock strength and discontinuities detection testing techniques have been developed both indirect (geophysical) and direct thus making possible closer roof-strata examination. In this paper critical roof span criterion is discussed as a basis for selection of proper mining system in terms of desirable stability of mine opening .

Jan 1, 1982

By John C. Stankus

The 3 Right pre-developed longwall recovery entry at Signal Peak Energy?s Bull Mountain No. 1 mine was designed to prevent the abnormal roof conditions encountered in its firsttwo recovery entries. Unique geological conditions, such as the low overburden of approximately 200 feet and prevalence of roof joints in the sandstone overburden, contribute significantly to abnormal conditions during longwall recovery. The 3 Right recovery entry was 42 ft wide and developed in two stages, 21 ft wide in each stage. The entry roof was reinforced with steel wire mesh/non-metallic recovery mesh, high-capacity primary bolts and cables. After all the support was installed, the entry was completely backfilled with specially designed, cuttable, low-density cement. The roof bolting and backfilldesign were based on current practices in this mine and successful practices in other mines in the U.S. and Australia. Extensive instrumentation was installed in the recovery entry for continuous monitoring of load transfer as the face approached and cut into the recovery entries. The support design was completely successful with a smooth cut-through on January 29 and 30, 2014, significantly reducing the shield recovery time and meanwhile protecting the safety of miners. Based on actual observance and practices of the 3 Right recovery entry, recommendations on improvement and modificationsof roof support for 4 Right recovery room are presented.

Jan 1, 2014

By David Conover

Knowledge of the magnitude and direction of the horizontal secondary principal stresses is a critical factor in designing the layout and mining sequence of underground openings. Typically, horizontal stress measurement has been accomplished using overcoring or hydraulic fracturing. Hydraulic fracturing can be accomplished from surface boreholes prior to development, but the technique relies on numerous assumptions regarding the rock mass and the stress field, and interpretation of results is somewhat subjective. Traditional overcoring provides a more precise measurement, but requires underground access. To allow for precise measurement of the horizontal stress field from surface boreholes, the In-situ Stress Tool (1ST) was developed by SIGRA Pty of Brisbane, Australia. Used in conjunction with HQ wireline coring, the 1ST contains a battery-powered data logger that records tool orientation and monitors six diametral deformations as the tool is overcored. The IST has been used successfully for several years in Australia, but has only recently been introduced in the United States This paper discusses how the IST was used to measure the pre¬mining horizontal stresses at a western U.S. coal mine. Seven successful measurements were obtained in two holes at depths ranging from 250 to 800 ft. Results were consistent, showing moderately biaxial stresses greater than those expected from gravity loading, but relatively low compared to rock strength. In addition to describing the overcoring equipment and procedures, various problems encountered during testing and the accuracy of the results will be discussed.

Jan 1, 2004

By Brian White

Two examples of en echelon mining-induced fractures seen in hard¬rock mines provided a basis for inferring that fracture zones and bedding plane separations immediately surrounding mine openings are promoted by oblique shear into the openings. It is hypothesized that initial fractures or separations form at the comers of openings as a result of high stress and physical constraint on the rock&apos;s ability to deform elastically toward the opening. These conditions result in a locally preferred direction of shearing. The shearing, in turn, generates tensile stress that initiates a progression of systematically offset fractures approximately parallel to the direction of greatest compressive stress. The fractures or bedding separations create tabular rock layers that amplify shearing displacement through bending and dilation. Such shearing effectively reduces and redistributes the compressive stress, but significant dilation is an inevitable consequence. The combination of dilation and shearing and the progressive development of fracture zones have important implications with respect to ground support. The concept of mining-induced fractures forming as a result of shear is illustrated by two examples from coal mines. First, frac¬tures seen at longwall faces probably result from shear associated with subsidence. The fracture zone that develops approximates or possibly defines the draw angle of subsidence. As the face advances, fractures extend downward along the lower edge of the fracture zone, while upper extensions of the fractures are pressed closed. Fracture zones in entry roofs provide a second practical example. Here, mining-induced fractures typically follow bedding planes. The shear zone model suggests that the first bedding separations develop near the edges of the roof and successive separations progress upward and toward the center. However, if the direction of greatest stress is inclined with respect to the roof, a fracture or bedding separation zone may propagate from one side only and also extend higher. Because coal ahead of the face provides some support against lateral shear deformation, bedding separation is inhibited near the face. Rock bolts installed close to the face ultimately become more strained and bent than bolts installed a few meters from the face, and bolts installed through the more remote part of a separation zone may ultimately experience the greatest tensile and bending strains. This model is supported by field data documenting progressive bolt failures that rapidly propagated downward across the roof during face advance.

Jan 1, 2002

By Larry Stolarczyk

A clear vision of the future coal mining industry was developed into a hierarchy of technology needs by the National Mining Association (NMA) and the Chief Executive Officers of the mining industry. Although improvements in safety and environmental factors were the main drivers in the technology roadmapping workshop sponsored by the Department of Energy, the agile mining machine of the future must efficiently extract coal from deeper, thinner, and more geologically complex coal beds. One of the challenges will be to develop sensors and software that enable clean coal cutting in a changing geologic environment. The roadmap identifies imaging ahead of raining and horizon control within the top ten needed technologies. For these technologies to be adopted by the mining industry, they must be proven to be effective while driving down mining cost and risk. This paper describes how three-dimensional imaging ahead of mining and horizon sensors enable improved ground control and safety in the mining of underground coal.

Jan 1, 2003

By Christopher Mark

Current longwall pillar design methods are based on many assumptions about pillar and entry response to longwall abutment loads. Knowledge of the magnitude and time-of-arrival of abutment loads is essential for Improving design procedures. The abutment loads are in turn related to the development of yield zones and horizontal confining stresses in pillars. Entry stability, which is the goal of any longwall pillar design, is affected by in situ stresses as well as the interaction between the roof, pillars, and floor. The paper describes a study performed in a longwall panel at a West Virginia coal mine. The behavior of two headgate pillars and the adjacent entries was- monitored as the longwall face approached and moved past. The results provided a detailed picture of the response of long- wall pillars and entries to abutment loadings.

Jan 1, 1986

By Anthony T. Iannacchione

This study, funded by the Appalachian Research Initiative for Environmental Science (ARIES), examines how mine layout, mining method, and geology interacted to allow water from the Grove No.1 mine pool to discharge into local surface waters. Federal and State regulations prohibit the discharge of acid or iron-producing waters from underground coal mines. Mining companies design barriers around their operations to prevent mine waters from discharging to the surface. The Grove No.1 represents one mine where these designs proved inadequate. Unique geologic conditions at the Grove No.1 mine pool, combined with retreat room-and-pillar mining, contributed to a discharge that required passive water treatment.

Jan 1, 2013

By Ed D. Doney

Based on the subsidence data collected through a comprehensive subsidence monitoring program con: ducted over two longwall panels in an Illinois coal mine, mathematical models have been proposed for predicting final and dynamic subsidence in the Illinois coal basin.

Jan 1, 1990

By D. W. H. Su

This paper presents the results of ill situ horizontal stress measurements using a Minifrac system in several northern Appalachian coal mines. The effect of stress magnitude and orientation on longwall gate entry stability was analyzed using a series of three-dimensional finite element analyses. The best headgate stability is achieved if the maximum horizontal stress is aligned with the direction of longwall retreat or if the panel is oriented such that the maximum stress relaxes over the headgate due to the presence of the newly formed gob. The degree of horizontal stress damage to longwall gate entries depends largely on the stress magnitude and roof geology. Accurate assessments of support or design techniques which may mitigate longwall headgate or tailgate instability in areas of thinly laminated roof and high horizontal stresses must account for the in situ horizontal stress state and site specific roof geology. The ability to measure stresses and map geology is thus essential to prevent ground control failures at the longwall headgate.

Jan 1, 1995