Search Documents

By C. A. Wiggins

The new Niagara Falls Intake Tunnel, mined in the highly fractured Lockport Dolomite, encountered prolific inflows of water contained in rock seams directly linked to the Niagara River. These inflows were pressurized and, more significantly, contained high concentrations of dissolved H2S gas. The contractors attempts to control the water/gas inflows included cement and chemical grouting from inside the tunnel. Ultimately, improving the rate of air exchange in the tunnel by increasing the fan capacity, in conjunction with a pattern down-hole pre-grouting program along the tunnel alignment allowed the contractor to control the concentration of H2S gas and complete the tunnel.

Jan 1, 1997

By James W. Evans

It appears that all extractive processes involve, at one or more points, fluids (gases or liquids) and that the flow of the fluid is an essential part of the functioning of the process. Usually that flow is turbulent and the turbulent flow frequently determines the rates of mass and heat transfer as well as other important phenomena such as bubble/droplet breakup and coalescence, particle suspension, etc. Over the past decade many attempts have been made to model turbulent flows in metallurgical unit operations. The present paper summarizes some of that work. Amongst the operations considered are agitated leaching, ladle metallurgy, electrowinning/refin- ing, induction furnaces, Hall cells and electro- magnetic casting. Where possible, comparisons are made between model predictions and experimental results.

Jan 1, 1990

By Irwin H. Reiss

Gentlemen, the title of my paper is Surface Mining An Interim Land Use. Surface mining has become one of the major controversies of our time. This has happened in spite of the fact that all surface mining to date has involved only 6 million acres out of a total of 2300 million or approximately one-fourth of one percent of the total land area in the United States. I'm not going to dwell on whether peoples' perspectives are out of focus in light of the area involved, the energy crisis, national security, or the international balance of payments problem. While these things are all critically important, it is not the function of this paper to relate to them. Maybe the amount of attention attracted to surface mining is out of proportion to a lot of other things, but I don't feel that we should use that as a basis for procrastination. However, let me categorically state that anything that affects the surface of the earth is a form of land use --- be it an interstate highway, a power plant site, a golf course, a corn field, a strip mine, or the plot of ground on which your house is located.

Jan 1, 1974

By H. M. Giegerich

About Cominco Only the original Broken Hill zinc deposit in Australia is larger than Cominco's Red Dog deposit. Indeed, the third largest zinc deposit in the world is Cominco's own Sullivan mine in British Columbia. The production plan at Red Dog is based on mining 1.9 Mt/a (2.1 million stpy) or ore, to produce 635 kt (700,000 st) of zinc and lead concentrates. At full production, Red Dog will be the largest zinc mine in the Western world. It will also be one of the lowest cost producers in the Western world. And Red Dog will be one of the first major hardrock mines to operate in Alaska in modern times. The Red Dog project will be the third and largest of Cominco's Arctic mining developments in the past 13 years. The company's Black Angel mine in Greenland started up in 1973. And the Polaris mine, high in the Canadian Arctic, began production in 1982. Red Dog is one of the world's great mineral deposits. It is a unique combination of large size, high grade, and a waste-to-ore ratio less than 1:1. The present mineral reserve (Table 1) is estimated to be 77 Mt (85 million st), at a grade of 17.1% zinc, 5% lead, and 82 g/t (2.4 oz per st) of silver. Mine life is estimated at nearly 50 years. Cominco is the largest producer of lead and zinc in the Western world. Cominco's smelter in southern British Columbia is the largest lead and zinc plant in the west. Cominco also produces copper, steel, tin, gold and silver, along with potash, ammonia, urea, and phosphate fertilizers. But Cominco's major products are lead and zinc. At present, Cominco produces more than 10% of the Western world's needs for these metals. Background-Red Dog The Red Dog mineral deposit is located in northwestern Alaska, about 960 km (600 miles) by air from Anchorage, Alaska's largest city. The Red Dog region is home to more than 5000 people living in 11 villages. The largest village is Kotzebue, with a population of about 2500. The village is located about 144 km (90 miles) southwest of the mine. The country around Red Dog features rolling hills, leading into mountains to the north and east. The deposit, at an elevation of 305 m (1000 ft), is in permafrost. But the area is not nearly as cold as that encountered in the Canadian Arctic, or on Alaska's North Slope. At Red Dog, the permafrost is relatively fragile. It can be thawed fairly easily, a factor in engineering designs. Red Dog Creek flows through the mineral deposit. One of the natural phenomena at Red Dog is the presence of significant heavy metal contamination in the creek. This has eliminated all fish in the vicinity of the deposit. The contamination, and resulting mineral stain, led to the discovery of Red Dog. The staining is caused by rain and snowmelt. This leaches the heavy metals from the mineral zone, which comes right to the surface in many places. As mining progresses, this surface mantle will be removed. This will

Jan 12, 1986

By V. F. Hollister

Copper and gold were discovered in the Copper Canyon area of the Battle Mountain district of Lander County, Nevada, in August of 1866. By 1876 a gravity plant was con¬centrating oxidized Copper Canyon copper-gold ores. The history of mining in the district to 1967 has been summarized by John E. Frost (in press) as a case history of the discovery of the Battle Mountain porphyry copper deposits. His summary is not repeated here; rather, the present case history covers exploration since 1967, primarily for gold ores. Subsequent to the construction by Duval of facilities to mine the porphyry copper deposits in 1967, Duval established a geologic staff at the mine to continue district exploration. The staff was guided by David W. Blake, who acted as chief geologist for Duval's exploration in this part of Nevada. Blake's activities led to the publication of numerous technical articles, including his contribution to the US Geological Survey Professional Paper 798-B. A part of that volume is attached as a reprint (pages 23 through 66) as an explanation of the geological setting of mineralization in the district. The work by Blake and his staff recognized metal zonation in the skarn environment at Copper Canyon, and their studies were incorporated in the development of the Tomboy-Minnie gold deposits that are peripheral to the porphyry. Exploration continued beyond the immediate vicinity of the porphyry and the Fortitude ore zones were discovered. These skarn deposits are described in the attached article by Wotruba, Benson, and Schmidt, published in the July 1986, MINING ENGINEERING. The continued exploration successes at Battle Mountain reflect on the well organized and effective exploration team developed at the mine. The team has provided successive discoveries in a district known mostly for ore bodies that are exhausted in a few years' time.

Jan 1, 1990

By D. U. Deere, T. R. Harrell

Factors such as rock cover, rock type and rock quality can exert a dominate influence on the behavior of a concrete tunnel lining. This paper will present and discuss the investigation, evaluation and use of such factors at the Rocky Mountain Pumped Storage Project in the design of the 10.67m (35 foot) diameter concrete tunnel lining. A plane strain, finite element analysis was performed on the concrete/rock system. The finite element model consisted of a concrete lining zone and three (3) rock zones; a highly destressed rock zone, a transitional rock zone and an intact rock zone. Zones were differentiated from one another by varying the modulus for each zone. Results of this study yielded a concrete lining strain from radial expansion which was used in the crack control calculations for the concrete tunnel lining. After the tunnel excavation was performed, plate jacking tests and additional seismic surveys were run on the tunnel walls. This testing served to confirm the rock modulus values used in the preliminary analysis. However, results were observed which indicated that a two zone rock model would more accurately represent in-situ rock conditions than the three-zone rock model used in the preliminary analysis. This revision to the concrete/rock model was made and a final concrete tunnel lining analysis was performed.

Jan 1, 1986

By Jim Oehler

The US minerals industry, as well we know, has been hit hard by the recent recession and is faced with what is projected to be a slow recovery. Even so, there was an underlying feeling of optimism at American Mining Congress' International Mining Show in Las Vegas, NV, Oct 11-14. More than 25,000 people attended during a particularly rough financial year, dispelling fears that attendance would dip sharply below 1978's 30,000 plus tally. The equipment expositionheld every four years-was the largest show of its kind this year in the Western Hemisphere in terms of exhibit space, providing an extensive view of mining-related equipment. In addition to the nearly 700 exhibits occupying more than 445 hm2 (11 acres), 20 technical sessions were held covering topics ranging from minerals availability and the state of the mining industries to communications, computers, and accounting. Government officials were well represented, with six US senators and five US representatives participating in various convention functions. Sen. Paul Laxalt (R-NV) was the keynote speaker at the welcoming luncheon. Other senators involved in the show included Howard W. Cannon (D-NV), Pete V. Domenici (R-NM), James A. McClure (R-ID), Frank H. Murkowski (R-AK), and Steven D. Symms (R-ID). Representatives on the program were Joseph M. Gaydos (D-PA), Guy Vander Jagt (R-MI), Don Young (R-AK), Jim Santini (D-NV), and Ceil Heftel (D-HI). There were also many international vistors at the show, including exhibitors from Australia, Austria, Canada, England, Finland, Sweden, South Africa, and West Germany. Equipment Highlights Equipment and services featured at the exposition ranged from aerial mapping to wire rope. Aisle space alone between exhibits exceeded 8 km (5 miles). And the companies represented ranged from small businesses to large corporations. Some of the company products described here are representative of the many exhibitors in attendance. Atlas Copco's extensive display of rock drilling and tunnel and shaft boring equipment featured its Boomer H-201, the newest addition to its line of underground drifting rigs; the ROC 306, a new track-mounted, high pressure down-the-hole drill rig; a new hydraulic surface crawler drill, the ROC 712H, designed for small and medium-size holes in quarries and small open-pit mines; a computerized analysis system, CARE (see page 1570), designed to project productivity and operating costs for various mining operations; several electro-hydraulic loaders, including the new rail bound LM E60 and LM E80, and two Hagg-loaders-the 7HR and 10HR-that use two digging arms to rake and guide muck; a mechanized blasthole charging system; rock bolting equipment and its new Swellex roof bolting method; Sandvik Coromant drill steel and bits; and its new Jarva R200 raise boring machine.

Jan 11, 1982

By Gabriel E. Zárate, Juan C. Guzmán

In Chile there are significant amounts of gold in flotation tailings that could be recovered, being heap leaching the most promising alternative. In order to determine the feasibility of treating these tailings by this method, a detailed study is carried out using 4 representative samples. After defining the best conditions an economic evaluation is done for a plant treating 200 tpd, sensibilizing with respect to parameters such us gold price, tailing grade and capital costs. The results show that it is technically feasible treat these gold tailings by heap leaching with gold extractions over 70 %. It is also economically feasible for gold grades higher than 0.5 g/t and gold prices over 350 US/oz.

Jan 1, 1987

By W. Jacobi, F. Steinhausler, A. C. James

INTRODUCTION In 1979 the Committee on Radiological Protection and Public Health of the Nuclear Energy Agency (OECD) defined a programme of work needed to improve radon dosimetry and monitoring. A Group of Experts in this field was established by the NEA and at the first meeting of the Group the authors were designated an initial task with the following terms of reference:- To review dosimetry of radon, thoron and their daughters, and in particular:- - to examine analytical models for the assessment of dose to individuals who are exposed to aerosol mixtures of these nuclides; - to examine the state of knowledge of the characteristics of aerosol mixtures of these nuclides and other factors that influence the dose to the lung, and identify those parameters which should be measured for dosimetric purposes in radiological surveillance programmes; - to identify areas where further study or research are needed. In this presentation we attempt to examine, with these objectives, the relationship between exposure to radon and thoron daughter aerosols expressed in terms of the working level month l (WLM), or its SI equivalent, and dose accumulated by sensitive tissues of the lower respiratory tract. Over the past two decades many attempts have been made to calculate the lung dose equivalent to l WLM exposure in mine atmospheres, usually in terms of the maximum dose to basal cells in a small part of the bronchial tree. The calculations have employed variously detailed models of airway anatomy, aerosol deposition, ciliary clearance and dosimetry of tissue at the bronchial surface, and are well reviewed elsewhere (Walsh, 1970; UNSCEAR, 1977; Jacobi, 1977; Fry, 1977). They agree in the conclusion that basal cells in segmental bronchi (between about the third and fifth bronchial generations) receive the highest dose, although estimates of this dose differ by more than an order of magnitude, ranging from about 0.2 to 12 rads per WLM (2 mGy to 120 mGy). The most critical parameters of these models are the assumed depths of basal cells below the bronchial surface and the fraction of the WL carried by free ions. When more realistic values of these parameters are substituted (Jacobi, 1977), the dispersion in calculated maximum doses to basal cells is reduced to give a much smaller range from about 0.3 to 1 rad/WLM (3 to 10 mGy/WLM). The parameters and methods employed in these various models, however, remain too diverse to infer the sensitivity of the dose conversion to practical variations in aerosol characteristics and the additional factors determining lung deposition and clearance. We have therefore taken the approach of developing newer models (Jacobi and Eisfeld, 1980; James et al, 1980) that can encompass the range of available experimental data on the physical and biological behaviour of radon and thoron daughters and also accommodate the different interpretations that can be put upon them. We have paid particular attention to the averaging of dose over tissues of equal sensitivity in the lung

Jan 1, 1981

By G. J. Lindenburg

The Velvet mine is located in the Big Indian district of the Colorado Plateau. The general area, also known as the Lisbon Valley district, is about 65 kilometers southeast of Moab, Utah and about 120 Kilometers southwest of Grand Junction, Colorado. As shown by the slide, the Velvet area is typical of the high desert of the southwest United States. The elevation at the decline collar is 1,967 meters above sea level. To date, the Velvet has produced 1.5 million kilograms of U308 and 2.1 million kilograms of V205. The current production averages over 4,000 metric tons of ore per month. Access to the Velvet mine is by a 1,160 meter long decline. Fresh air is supplied through the decline and a 152 centimeter cased borehole. Contaminated air is removed by two 152 centimeter cased boreholes. The east side of the mine is mined using a conventional room and pillar method; whereas the west side is mined as combination conventional and random room and pillar,

Jan 1, 1983

By Leo G. Martin, Richard G. Sherman

Recent sewer construction in downtown New Haven, CT required avoiding open trench methods because of near surface utilities and traffic congestion. The .73 km long alignment is in sands with the water table at the tunnel's springline. The designers felt the situation was ideal for an EPB machine; however, the tunneling method was left to the Contractor. The winning bid surprised everyone. The tunnel is being excavated by hand using an open face shield with breasting boards. The review of the bids indicates hand mining was approximately 1/2 the bid price of TBMs. Currently, excavation rates average 14 m/day with no excessive settlements.

Jan 1, 1993

By A. W. Jenike

Mine backfilling is a desirable method for the disposal of retorted oil shale. Hydraulic, mechanical and pneuna.cic transport and stowing methods were investigated, and the mechanical transport and stowing method using conveyors was selected as the most promising system. Transport of retorted oil shale at the rate of 3000 cons per hour (2700 t(h) to the backfill level, situated about: 2000 feet (610 m) below surface, with skips or conveyors is uneconomic. Hence, borehole transport utilizing gravity flow was investigated. This paper describes the theory of flow, flow properties of retorted oil shale, and the design of a borehole and hopper system.

Jan 1, 1978

By M. Popescu

In the southern part ?f the Occidental Carpathians an iron ore body embedded in crystalline schist was exploited. The presence of minerals such as magnetite, pyrite, pyro-chorine, allanite, monazite and xenotime, which also include within their structure substituted thorium isomorphic, was pointed out. The iron ore was processed by crushing, grinding and magnetic separation in order to obtain magnetite concentrates. The environment was affected by pollution generated by the mining activities. In 1995 due to the economic reasons, it was decided to cease mining exploitation and remediate the area. The paper presents the ecological impact caused by mining activities on a number of environmental targets and the population. The pollution sources, namely sterile dumps and mine waters are characterized (from the physical, chemical and radiometric point of view); the pollution pathways and theirs effects on potential targets, namely soil, vegetation, hydrographic network and population are identified as well. The degree of pollution due to all sources was assessed and maps of pollution sources distribution were generated. The supplementary effective doses for the population were assessed using rigorous scenarios and considering all exposure pathways. The rehabilitation plan includes solutions for dumps geometrization, covering and revegetation as well as mine waters management.

Jan 1, 2005

By N. A. Frazier

The technology for using limestone or lime to scrub SO2 from power-plant flue gas has significant implications to the limestone industry. A brief status report on these processes will be made, possible process requirements on the limestone properties will be reviewed, and projections on the buildup of demand with respect to time will be reviewed. Disposal problems inherent with the use of these throwaway processes will also be summarized. Given a viable technology, relations among (1) distance of power plants from low- and high-sulfur coal and limestone deposits, (2) modes of handling and transporting immense tonnages of bulk material-coal and/or limestone, and (3) regional air-quality standards are some of the factors which will ultimately determine the demand for limestone. A discussion of these factors will be presented, with the intent of identifying geographic regions where significant increases in production can reasonably be expected.

Jan 1, 1974

By J. H. Rowland, R. A. Thomas, III, C. D. Litton

Atmospheric monitoring systems (AMS) are required when using air from conveyor belt entries to ventilate working sections in U.S. underground coal mines. AMS technology has the potential to increase fire safety mine-wide, but research is needed to determine the detection and response times for fires of a variety of combustible materials. To evaluate the potential of an AMS for fire detection in other areas of a coal mine, a series of full-scale fire experiments were conducted to determine detection and response times from fires of different combustible materials that are found in U.S. underground coal mines, including high- and low-volatility coals, conveyor belts, brattice materials, different types of wood, diesel fuel, and a foam sealant. These experiments were conducted in the Safety Research Coal Mine (SRCM) of the U.S. National Institute for Occupational Safety and Health (NIOSH) located in Pittsburgh, PA, using a commercially available AMS that is typical of current technology. The results showed that through proper selection of sensors and their locations, a mine-wide AMS can provide sufficient early fire warning times and improve the health and safety of miners.

Jan 1, 2016

By Young C. Kim

Determination of the minimum sampling requirements of the run-of-mine (ROM) coal is very important for the purpose of meeting contract specifications. It is also important for the purpose of meeting emission regulations at a coal-burning power plant, such as the one located at Homer City, Pa. The classical statistical sampling theory can be applied to this problem, if ROM coal samples are known to be spatially (or serially) uncorrelated. On the other hand, the estimation variance concept from the Matherson's geostatistics must be used, if the samples are spatially correlated. Conditional simulation technique combined with simulation of the existing mining method is used to determine under which circumstances ROM coal samples do not preserve the spatial correlation. Only after establishing the degree of correlation that exists among ROM samples, an optimal sampling scheme can be devised using either the classical statistics Or the geostatistics. The minimum required sample volume can then be calculated using the well-known Gy's formula. This paper describes the results of the above investigation using the Helen coal mine data of the Homer City Owners. Empirical guidelines for determining the degree of correlation are also provided for coal mine operators.

Jan 1, 1986

By Michael Chender

Introduction Clearly, many problems confront the minerals industry today. Yet, at the same time, there is too much energy spent bemoaning the negative effects of difficult economic circumstances, low metals prices, and adverse government policies. These are factors that cannot be altered by individual mineral company reactions. In fact, as we look to the future, the only thing we can be certain of is that we will continue to be faced with uncertainty. Thus, an area that demands close scrutiny and that can significantly affect a company's performance in the future is the posture it adopts to deal with uncertainty. This paper looks at how strategies are developing to deal with this issue. It also examines some of the implications that implementing such strategies have for the role of the individual explorationist. Elements of strategy Whether mineral company strategies are based on diversifying or retrenching, on emphasizing primary production or downstream integration, there seems to be increasing agreement that in the current environment strategies must have several features. They need to be information-based - developed out of access to timely and complete data and analysis about proposed directions and competitor activity, rather than simply following a current fashion. They need to be flexible - adaptable in light of changes in the marketplace and an unpredictable industry. And they need to be cost-efficient - making the most of limited resources. Whether a company is looking for gold financing opportunities, acquiring polymetallic prospects, or doing grassroots exploration for diamonds, these three elements are increasingly essential. They not only allow the company to pursue its current goals most expeditiously, but also open it to hearing and using feedback in the most constructive way. The company can then improve or change strategy as it proceeds. And it can be best positioned to take advantage of opportunities as they arise. These elements of strategy place great emphasis on the skills of the individual. The need for critical intelligence and the reduced amount of capital available to manage are making it more obvious that exploration is a "people" business. This is in accordance with a general trend in many sectors of industrialized economies, reflecting the widely discussed shift from smokestack to information-based industries. Increasing the odds There is a direct connection between successfully implementing the approaches to strategy discussed above and encouraging and improving the quality of work of the individual explorationist. To illustrate the importance of this, some commonly quoted figures on the odds of discovery success can be used. These figures are arbitrary but illustrative. Assume that one out of 100 exploration prospects actually turns out to be a promising ore body, and that one out of 1000 becomes a mine. Based on our research, chances are the most of those

Jan 1, 1986

By K. V. Raj, R. Jacksha

Conveyor systems persist in being a source of injuries and fatalities in the mining industry. To reduce these incidents, better methods are needed to enhance the monitoring of probable hazards and improve situational awareness during the normal operation and maintenance of conveyor systems. To address these issues, researchers from the U.S. National Institute for Occupational Safety and Health (NIOSH) continue to investigate emerging technologies that show the potential to improve miner safety around conveyors. This paper presents a feasibility assessment by NIOSH researchers of a fully integrated, commercially available wireless Internet of Things (IoT) system to improve situational awareness around conveyor systems.

By D. M. Larsen, N. D. King

Since start-up in 1985, the Cannon Mine has produced and shipped a 170-g/ton (5 oz/ton) gold flotation concentrate to various smelters for gold and silver recovery. Several processes have been investigated to economically produce dore' at the mine site from the refractory concentrate. This paper describes laboratory and pilot scale test work used in the process design and engineering feasibility study of a 73-t/d (80 stpd) pressure oxidation and carbon-in-leach (CIL) facility. The designed pressure oxidation circuit utilizes a series of vertical autoclave units operating at 170°C (338°F) and 1.4 MPa (200 psig). Projected operating costs are discussed.

Jan 1, 1994

By Valerio Violo, Antonio Raschilla, George Kafantaris

"The Cityringen project in Copenhagen, Denmark will form a new circular line in the city center and will consist of 21 new stations (17 + four transfer stations) and approximately 31 km (19 miles) of earth pressure balance (EPB) twin-bored tunnels.The new tunnels passed under the historical building of Magasin du Nord, McDonald’s and two pubs in the heart of the city with a minimum cover of about 4 m (13 ft).To minimize the movements, a complex system of compensation grouting and jet grouting soil treatment was performed. A detailed action plan between the parties involved allowed coping with the critical tunnel boring machine’s (TBM) successful passage.The Cityringen is an extension of the existing metro line underground Copenhagen and will include the City Circle Line, 15 km (9.5 miles) of twin tunnels looping around the city. The City Circle Line will form a new circular track inside the city center and will intersect the existing M1 and M2 lines at Kongens Nytorv and Frederiksberg stations, as well as suburban train services at København H, Østerport and Nørrebro. It will extend the Metro network to the Nørrebro, Østerbro areas and the central station at København H (Fig.1). The two new lines M3 and M4 will run on the same tracks, but the M3 will be a circle route running around the entire line, whereas the M4 will drive from the station to the north side of the city.The €1.5 billion design-build contract was awarded by Metroselskabet in January 2011 to the Copenhagen Metro Team (CMT), a joint venture (JV) between the Italian companies Salini, Tecnimont Civil construction and Seli SpA. Since the bankruptcy of Seli SpA and Tecnimont, Salini Impregilo now owns 100 percent of the JV shares. Seli Tunneling Denmark ApS, a subcontractor to CMT, was initially constituted as a Seli SpA subsidiary and, following the economic difficulties of Seli SpA, was acquired in 2015 by Salini Impregilo. Seli Denmark is in charge of the tunnels excavation and lining and owns the four 5.84-m (19-ft) diameter Seli/Kawasaki earth pressure balance machines."

Jan 5, 2017