Search Documents

By John J. Sammarco

Light-emitting diodes (LEDs) are emerging as viable replacements for incandescent (INC)-based cap lamps used in mining. The photometric and energy characteristics of these light sources differ in important ways. This paper describes the performance of LED and INC sources in cap lamps in terms of correlated color temperature, color rendering, light output, electric power, ambient temperature and air flow, and light source aging. Importantly, these characteristics can influence a miner?s ability to spot mining hazards thus impacting safety. Second, some of these characteristics interact with the operating life of the cap lamp?s battery power, such that differences between LED and INC sources can be magnified toward the end of a 10-h battery discharge cycle. Empirically, we have determined that after 8 h at an ambient temperature of 25 ?C, the average light output of an INC cap lamp can decrease to about 69% of its initial value when powered by a lead-acid battery, and it can decrease to about 65% of its initial value when powered by a nickel-hydride battery. An LED-based cap lamp using a constant current drive circuit can maintain about 96% of its initial value when powered by a nickel-hydride battery. Real-world tests addressing the effects of ambient temperature and air flow on the light output of an LED and INC cap lamp were conducted in the National Institute for Occupational Safety and Health Safety Research Coal Mine. The LED cap lamp yielded a vertical average illuminance improve­ment of approximately 9.5%, and the INC cap lamp yielded a vertical average illuminance degradation of approximately 4%. The differences between LED and INC cap lamps were further quantified by the calculation of ?mesopic luminance? data that indicated for the same photopic luminance (i.e., as measured using a conventional light meter) the LED cap lamp could be up to 38% more efficient than the INC cap lamp with a lead-acid battery at the end of the 10-h driving cycle. Lastly, accelerated life tests were used to empirically determine light output depreciation as the INC light source age approached its useful life. There was about a 35% decrease in light output. This is quite considerable, particularly given that the light output will decrease an additional 30% to 45% over the period of a 10-h shift. The implications of the differences between LED and INC sources are discussed. This information is crucial in determining how visual performance could be affected for real-world conditions where batteries discharge during the work shift and as the light source ages. To date, only idealized conditions have been used for LED and INC cap lamp visual performance research.

Jan 1, 2009

By Stephen A. Hare, O&apos

Powder metallurgy processing of commercial Raney nickel powders was examined. The typical angular particle shape, in conjuction with aluminum present in a eutectic phase, facilitated interlocking leading to excellent green strength after compaction. Density and porosity as influenced by the compacting pressure were studied over the range of 37.5 to 207 meganewton per square meter (MN/m2). Sintering in an inert atmosphere from 575° to 850° C caused a volume increase which is attributed to a solid state reaction between Al and Ni2Al3 phases. The reaction is 3Al + Ni2Al3 ? 2NiA13. A thermal pretreatment of 70 hours at 700° C was required to prevent this reaction from occurring during sintering. Density and porosity as a function of compacting pressure and sintering temperature were determined after a thermal pretreatment of the powder.

Jan 1, 1976

By H. F. Yancey

Traditionally the Pacific Northwest has relied on hydroelectric power, which has been both abundant and cheap. However, comparatively few hydroelectric sites capable of providing low-cost power remain, therefore the need for supplemental thermal generation, perhaps within the next decade, is generally recognized. Based on the present cost and availability of competing fuels, coal seems to be the logical choice for projected thermal power plants. Power companies and public utilities have become interested in establishing reserves of coal for future use. One deposit explored in 1958-59 lies in southern Thurston and northern Lewis Counties, Wash., near Centralia. Drilling, totaling 22,700 feet, proved the existence of 70 million tons of strippable coal--an ample reserve for the projected power plant. The coal, like most others and particularly those of Washington and Oregon, when mined in full seam section by mechanical methods, would require cleaning to make it suitable for use. The amount and nature of the impurities in this coal dictated a thorough investigation of its cleaning characteristics to establish economic factors and to insure proper preparation-plant design. Therefore, arrangements were made through a cooperative agreement to conduct such work at the Seattle Coal Research Laboratory of the Bureau of Mines. This report describes that investigation. The results are of interest primarily in connection with the utilization of this particular deposit, but some of the information developed is applicable to other deposits of low-rank coals in the West, because the impurities in these coals differ greatly in behavior from those generally associated with the higher rank coals of the Appalachian field.

Jan 1, 1961

By Arnold B. Hubbard

A thermal decomposition study of the kerogen in three Colorado oil shales was made at different temperatures by heating the shales in the absence of oxygen at atmospheric pressure and measuring the decomposition products (gas, oil, and bitumen) formed. From these data the specific reaction rates, "k", for the thermal decomposition of kerogen were determined for each temperature studied, making it possible to calculate the time required to accomplish a given amount of decomposition within the temperature range. The influence of temperature on reaction rates was presented by plotting the data according to the Arrhenius equation, thus providing a means of estimating the values of "k" for any temperature within the range of this study. It was found that the specific reaction rates for the thermal decomposition of the kerogen in the three sampler were comparatively equal at corresponding temperatures.

Jan 1, 1950

By R. Barany

The heats of formation of seven substances were determined by solution calorimetry. At 298.15° K, the heat of formation of lithium sulfate from lithium, rhombic sulfur, and oxygen was -343.1 ± 0.7 kcal/mole, and the heat of formation of lithium sulfate monohydrate from lithium, rhombic sulfur, oxy-gen, and hydrogen was -414.3 ± 0.7 kcal/mo1e. For the silicates, the heats of formation at 298.15° K from the elements were kaliophilite, -503.8 ± 0.5 kcal/mole; leucite, -721.6 ± 0,8 kcal/mole; eucryptite, -505,2 ± 0.6 kcal/mole; alpha-spodumene, -727.9 ± 0.9 kcal/mole; and beta-spodumene, -721.1 ± 0.9 kcal/mole. The corresponding heats of formation at 298.15° K from the constituent oxides were kaliophilite, -42.7 ± 1.1 kca1/mole; leucite, -42.8 ± 1.1 kcal/mole; eucryptite, -16.1 ± 0.7 kcal/mole; alpha-spodumene, -21.0 ± 0.7 kcal/mo1e; and beta-spodumene, -14.3 ± 0.7 kcal/mo1e.

Jan 1, 1966

By R. Karl Zipf, Z. T. Bieniawski

"Researchers at The Pennsylvania State University are engaged in a project to understand the mechanics of respirable size fragment formation in coal. The project is based on the premise that a thorough understanding of the fundamental mechanics of fine fragment formation may lead to techniques for reduction and better control of coal dust problems in mines. Presently, it is believed that the mode of fracture propagation which can range from pure tensile to pure shear or any mixed mode in between and the loading or displacement rate can influence the amount of respirable size fragments that are generated on new fracture surfaces during the fracture propagation process The essence of any coal cutting process is one of mixed mode fracture propagation. To study the crack propagation process, a unique mixed mode testing rig was designed and fabricated. This rig is capable of applying loads to a prenotched test specimen that range from pure Mode I (tensile mode) to nearly pure Mode II (shear mode) or many mixed mode loading combinations. It is also possible to apply different loading or displacement rates to the test specimen. With this rig, it is possible to create new fracture surfaces via the different fracture modes and under various loading conditions.These new fracture surfaces are examined with a scanning electron microscope (SEM) to characterize the amount of structural damage and respirable size fragment formation that occurs during the fracture process. Initial observations suggest that the amount of fine fragment formation and the new fracture surface appearance is related to the fracture initiation conditions, particularly the fracture mode and the loading rate. Mode II loading and higher loading rates seem to generate more structural damage and respirable size fragment formation that Mode 1 loading at slower rates.With the mixed mode test rig, the mechanics of fracture initiation for a single crack can be controlled to better understand its influence on respirable size fragment formation. Such understanding may lead to methods which characterize the tendency of specific coal seams to produce undesirable fine fragments during the fracture process, or it may lead to rational recommendations and design guidelines or coal mining machines which inherently produce less dust.IntroductionAs part of a larger effort to reduce the incidence of coal workers pneumoconiosis (black lung) in coal miners, researchers at The Pennsylvania State University are engaged in a project to understand the fundamental mechanics of fine fragment formation in coal. This project is part of a com¬prehensive research effort within the Generic Mineral Technology Center for Respirable Dust which is jointly administered by The Pennsylvania State University and West Virginia University.The principal source of the coal dust in underground mining is the cutting operation. The U.S. Bureau of Mines (USBM) and various European research organizations have conducted investigations into the mechanics of coal cutting for many years. These studies of airborne respirable dust (ARD) formation have concentrated on empirical studies of the various cutting parameters and their effect on ARD for¬mation. The parameters study include depth of cut, cutting speed and bit spacing.(1,2) Other studies investigated the effect of symmetric and asymmetric bit wear and various bit geometries and designs (3-5) Roepke(6) summarized the principals of proper coal cutting to minimize dust formation by recommending to ""cut at maximum depth (maximum advance rate) at all times, at minimum RPM, with the fewest possible bits, having the lowest possible included tip angle."" Most coal in the U.S. is mined with the continuous mining machine which inherently cannot meet these design recommendations.(3)It is recognized that respirable size dust particles are formed and/or liberated by a fracture process. One extremely interesting and useful study performed very early in the USBM dust re"

Mar 1, 1989

By Robert C. Steckley

The Bureau of Mines performed a fragmentation experiment in cooperation with Duval Corporation in a porphyry copper-molybdenum deposit near the Sierrita pit south of Tucson, Ariz. This experiment evaluated the fragmentation created in a 10-hole test blast having blasthole spacings of 25, 20, and 15 feet. The 10 blastholes were 9 inches in diameter and contained a total of 17,400 pounds of aluminized slurry blasting agent in 50-foot columns with 60 feet of stemming. Diamond drill core examination was the primary method used to determine the condition of the rock before and after blasting. These core examinations included study of length recovery, rock quality designation (RQD), weight recovery, and size distribution. Topographic surveys were used to measure the rock swell produced by the blast and a fragment size distribution was obtained for the broken material on the surface. Fragmentation to depths of 110 feet was excellent from the 15-to 20-foot blasthole spacing patterns. Good breakage was also produced by the 25-foot pattern although the effects of the blast were not so obvious. In situ leaching tests were not conducted. However, based only on size consideration, all three blasting patterns produced adequate breakage for successful leaching.

Jan 1, 1975

By A. B. Needham

This paper, which describes mining practices at a mine in the Cave- in-Rock, Illinois, fluorspar district, is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. Ore deposits in the southern Illinois-western Kentucky fluorspar dis- trict are of two general types (1) the flat-bedded, lenticular replacement and (2) the relatively narrow, rather steeply dipping fault or fissure filling. This paper describes production methods used and results obtained in mining one of the bedded lenticular ore bodies that are prevalent in the northeast portion of the district near Cave-in-Rock.

Aug 1, 1949

By C. H. Schack

Although viscosity is known to be important in processing and handling finely ground urea, its effect has never been fully quantified. This report describes the methods used and the results obtained in the initial phases of a broad investigation of the influence of viscosity of water suspensions of minerals in flotation, thickening, filtering, and other mineral-dressing unit operations. Several types of vis-cosimeters were tested before reliable and reproducible results could be obtained on mineral suspensions. After the viscosimeter used in the research was calibrated and standardized, tests were made on six pure minerals to study the relationship of pulp density, particle size, crystallinity, and cleavage on viscosity. An orifice-type viscosimeter equipped with a mechanical stirrer gave as good results as other types and was more flexible, faster, and simpler to operate. The orifice-type viscosimeter, when calibrated and standardized with glycerin and water mixtures, proved satisfactory over a wide range of viscosities. The accuracy and reproducibility were reasonably constant between 1 centipoise and 200 centipoises, the anticipated range in common mineral-dressing unit operations.

Jan 1, 1957

By K. L. Paciorek

The aim of the present study was to determine the thermal oxidative behavior of materials used in coal mines, with emphasis on the type and relative concentration of the products, in particular the toxic species formed. To supplement this work and to gain understanding as to the type of products possibly formed and also to assess the limitations and advantages of the various analytical methods used a literature survey of the past investigations performed on the compositions of direct interest to the subject program was conducted. The compositions thus covered were cellulose, polyvinyl chloride, neoprene, urethanes, polyamides, polyesters, polyethylene, epoxy, phenoxy, urea-formaldehyde and melamine formaldehyde resins. The results of this review are compiled in the Appendix. The experimental work consisted of thermal oxidative degradation of 36 materials and 4 composites using a stagnation burner apparatus developed in these laboratories which affords a dynamic system approximating somewhat the conditions encountered in underground coal mines. This technique as employed during this program gave only the relative product concentration at specific periods of the decomposition process, The advantage of this approach is that in this manner screening of materials can be accomplished in conjunction with some assessment of the decomposition rate as influenced by temperature and material composition. Limited static tests were performed using a sealed tube method. The materials studied were grouped according to their compositions. The following were the main groups: (a) polyvinyl chloride-containing materials, (b) neoprene compositions, (c) rigid foams (urethanes, isocyanates), (d) miscellaneous materials (including jute, fiberglass, polyethylene and some articles of unknown composition), (e) coal and fluids (phosphate esters, organic esters, oil-water emulsions), and finally (J) composites. The latter comprised a mixture of a phosphate ester fluid with (a) coal, (b) a representative polyvinyl chloride sample, and (c) a neoprene type composition.

Jan 1, 1972

By Roy Bartholomae

Noise generated by continuous mining machines in underground coal production is an important health hazard. Bureau of Mines Contract J0387229 covers investigation of this noise through laboratory tests of simulated cutting operations and through in-mine noise measurements. The results of these investigations indicate that coal cutting noise and conveyor noise are dominant sources of mining machine operational noise. Typical noise levels for both cutting and conveying operations are approximately 97 dBA (decibels A-weighted). For full operation of all machine systems, the overall sound pressure level is approximately 101 dBA. In-mine and laboratory test results show excellent agreement in both A-weighted overall levels as well as in A-weighted one-third-octave band spectra.

Jan 1, 1983

By Raymond W. Hiteshue

To aid in designing a continuous system for evaluating processes for converting coal to high-Btu gas] the Bureau of Mines determined the amenability of various coals and a char to hydrogasification at 800° C and 6,000 psig using a molybdenum catalyst. A lignite from Rockdale, Tex., an hvCb coal from Rock Springs, Wyo., a char from the low-temperature carbonization of the latter, an hvAb coal from Pittsburgh, Pa., and an anthracite from Luzerne County, Pa., were selected. Highest yields of gaseous hydrocarbons, 94 pet, based on maf feed, were produced from char, and lowest yields, 67 pct, were obtained from lignite. Hydrocarbon gases contained 82 to 92 pct methane, 8 to 15 pct ethane; and 1 to 3 pct propane.

Jan 1, 1962

By G. T. Fisher

The material requirements of carbide cutting tools for machining steel and cast iron are dependent on WC bonded with Co, with additions of TaCand TiC. The Bureau of Mines is conducting research to devise substi-tute materials, based on Ni-alloy-bonded TiC, for C-5-grade cutting tool applications. This substitution would result in less dependence on foreign sources for Co, Ta, and W, and use of lower cost materials. In this preliminary study, the Bureau investigated the effects of composition and processing variables on the transverse rupture strength and hardness of Ni-alloy-bonded TiC to identify compositions that exhibit promising mechanical properties. Further systematic modification of these compositions by soild-solution strengthening additions would subsequently be evaluated to obtain cutting tool materials with requisite properties and performance for C-5 applications. Compositions for evaluation were prepared by a powder metallurgy method of cold-pressing and liquid-phase sintering. Complementary analysis of compositions included chemical analysis, X-ray diffraction, energy-dispersive X-ray spectro-scopy, and density measurements. Based on results of this investigation, promising compositions were determined to be 59.37TiC-25Ni-5Mo-lO.63Mo2C, 59.68TiC-25Ni-3.33Mo-1.77Mo2C-6.67W-3.55WC, and 59.35TiC-25Ni-l.67Mo-3.54Mo2C-3.33W-7.1WC.

Jan 1, 1987

By T. E. Gray

This report describes the preparation characteristics of the more significant coals in Dickenson County, Va. It is one in a series planned to determine which coals are suitable for the production of metallurgical coke either as mined or after beneficiation. Nearly 4 million tons of coal was produced in Dickenson County in 1955, of which approximately 2.7 million tons was cleaned mechanically in 5 cleaning plants. The Federal Geological Survey has estimated that nearly 1,300 million tons of measured and indicated coal reserves remained in the county as of January 1, 1951.

Jan 1, 1958

By J. R. Sweet

The paper describing the raining operations at the Mt. Hope mine, Mt. Lope, N. J., is one of a series being prepared by the United States Bureau of Mines on mining methods, practices, and costs of various mining operations in the United States. Mt. Hope mine produces magnetite ore. It is situated in the general northern part of the State of New Jersey. The towns of Rockaway, Wharton, and Dover lie within a radius of 4 miles from the mine. Dover is 40 miles from New York City.

Jan 1, 1932

By Gary P. Sames

The Bureau of Mines recently initiated a study of geologic features that contribute to roof instability in western U.S. underground coal mines. The purpose of the study is to provide information for use in ground control planning and safety hazard reduction in that region, where mining activity has been increasing. Hazardous geologic conditions were surveyed in selected underground coal mines in Utah and Colorado, and both depositional and structural features were identified as potential ground hazards. Although the conditions found do not differ in kind from hazardous geologic conditions in the Eastern United States, they do differ in intensity of occurrence and relative importance. Three depositional features dominate where unstable roof occurs in western underground coal mines: paleochannel deposits, crevasse splay deposits, and flood basin deposits. Three structural features identified as hazardous, but not so widespread or common as the depositional hazards, are faulting, jointing, and igneous intrusions. This survey establishes a foundation for future studies aimed at reducing and preventing ground control accidents in western coal mines.

Jan 1, 1988

By Alan G. Mayton

The Bureau of Mines conducted one of the most extensive studies on surface mine illumination to date, to assess the illumination needs of mobile surface mining machinery with respect to the visual tasks required of machinery operators. Field Investigations were performed at 22 surface mining operations, coal and metal-nonmetal, within several mining regions of the United States. Visibility and illumination were measured for 159 visual tasks performed by equipment operators on or near 57 surface mining machines, including draglines, shovels, blasthole drills, bulldozers, loaders, haul trucks, graders, scrapers, and several service-type vehicles.

Jan 1, 1987

By R. M. Jimeson

Pressure-drop measurements through beds of granular iron, lathe turnings, steel wool, and parallel-plate assemblies were made at linear velocity and gas-density ranges expected in the Fischer-Tropsch hot gas recycle process.4/ Equations relating pressure drop, linear velocity, gas density, and bed porosity were derived. The results indicate that the exothermic heat of reaction can be removed at a lower cost by using catalyst beds with high porosity. INTRODUCTION The Fischer-Tropsch hot-gas-recycle process requires a catalyst offering low resistance to gas flow as one condition to economic feasibility. Conventional granular or spherical catalysts used during early development of the process in Germany did not meet this requirement. Large pressure drops across these beds made the cost of recirculating the gas excessive. The Federal Bureau of Mines is investigating the process by using novel and unusual catalysts that offer little resistance to gas flow. Pressure-drop measurements across these types of catalyst beds are discussed in this report.

Jan 1, 1959

By Robert W. Ageton

Optimal planning for mining the deep, lead-zinc-silver deposits of the Coeur d'Alene mining district, Shoshone County, Idaho, could be facilitated by a knowledge of the magnitude and direction of the pressure acting in the virgin rock. The distribution of primary stresses should be considered in order to prevent possibly destructive mining-induced stress concentrations. This particular investigation was concerned with determining stress in a zone 4,000 feet below the surface and known to be ender stress concentrations due to mining operations. Disking of the stress-relief cores obtained in a vertical down hole permitted qualitative evaluation from visual observations; the results indicate that a high lateral stress existed at the time the measurements were made. Stress-ellipsoid determinations gave a compressive principal stress of -13,000 psi oriented about N 45° W and nearly horizontal, a compressive principal stress of -11,000 psi oriented about S 45° W and abut 60° off the vertical pointing away from the vein, and a compressive principal stress -5 -7,000 psi oriented N 45° E and about 60° off the vertical, pointing toward the vein. Subsequent to the overcoring stress-relief drilling, a rock burst occurred about 100 feet northwest of the test site.

Jan 1, 1967

By James P. Ulery, Frank E. Chase

Clay veins found in coal mines have caused numerous injuries and fatalities. These structures plague all phases of mining, including entry development, pillar recovery, and panel extraction. Clay veins also increase production costs and may disrupt or halt mining. These detrimental aspects have prompted the Bureau of Mines to investigate the physical characteristics of and roof instability problems associated with clay veins. This was accomplished by observing and mapping clay veins in surface and underground mines. The occurrence and origins of clay veins were also investigated to determine predictive capabilities. The investigators found that clay veins normally occur in more stable, less rapidly subsiding coal basins. Clay veins result when tensile stresses develop fissures which are later infilled. These fissures can be propagated by compactional processes and/or tectonic stresses active during and subsequent to coalification. The Bureau also found that associated faults, fractures, and slicken-side planes commonly parallel clay veins and disrupt the lateral continuity of the immediate and, sometimes, main roof. When clay veins parallel or subparallel the direction of face advance, the roof is segmented into cantilever beams, causing unstable conditions. Consequently, the strata on either side of the clay veins should be bolted and strapped together to form a beam.

Jan 1, 1987