Search Documents

By James A. Bachmann, Christopher J. Gray

On December 26, 1994, at 1:00 am, Santa Fe Pacific Gold's Twin Creeks Mine experienced a major highwall failure involving over 2.5 million tons. The resulting effects of this slide were thousands of ounces of gold that were now deferred and an unstable wall above which made mining the slough material unsafe.

Jan 1, 1996

By Peter Moser, G. Reihholf

Holcim, one of the world's leading suppliers of cement, aggregates and concrete, has set up a few years ago a working group “Quarry” in order to optimize the performance of its central European quarry operations in terms of work safety, environmental standards and economic performance. One of the activities of this working group "Quarry" addresses the subject of blast fragmentation in the quarries. A benchmark study of the blast work in all quarries has shown substantial differences for the various operations in terms of drill& blast costs. Especially big differences were found with respect to the drilling patterns as a function of the borehole diameters and with respect to the utilization of the borehole volume for charging the explosives.

Jan 1, 2006

By R Yang, M Lownds

This paper reports studies showing the effects of delay scatter on the peak particle velocity (PPV) of blast vibration using a multiple seed wave (MSW) vibration model developed in recent years. The case studies also show the advantage of accurate delay timing on frequency control of blast vibration. The site parameters used in one of the studies are from a case in which the MSW model has been tested and confirmed to yield accurate predictions. This study uses an open pit blast design and a tunnel design in which blast vibrations using electronic detonators are compared with those from pyrotechnic detonators. Mean peak particle velocity (PPV) and the 97.5% upper bound PPV are compared. It is found that both these values increase significantly with the increase of the coefficient of variation of the site parameter. Using an open pit blast design, the modeling shows that electronic initiation shifts vibration energy to the expected frequency for a selected point of interest. However, for the same design of nominal initiation timing pyrotechnic detonators fail to shift vibration to the expected frequency due to its large scatter of timing.

Jan 1, 2011

By Greg Wyartt

In the Pilbara region of Western Australia, an iron ore mine is undertaking a high wall cut-back to improve stability and allow access to deeper ore deposits. Several sections of the wall have been classified geologically sensitive due to unstable localised geology, and therefore an engineered approach to vibration critical blasting was required. The use of electronic detonators allowed multiple signature (seed) holes to be incorporated into a production blast adjacent to the geologically sensitive area, therefore providing baseline vibration data to be used for future modelling with the added advantage of eliminating unnecessary pit closure downtime typically associated with a signature hole program. All subsequent blast patterns also incorporated multiple signature holes to provide additional data and allow continual updating – and therefore improved accuracy - of the blast prediction model.

Jan 1, 2018

By Deepak Vidyarthi

This paper deals with various measures adopted in protecting a conveyor duct (named after a Conveyor Belt that was numbered as ‘02’) housing a 1600 mm (63 inches) belt conveyor system in a large, heavily mechanized open cast iron ore mine, producing about 20.0 million tones of ore per annum.

Jan 1, 2008

By H G. Bosmare, G Bedser, C V. B Cunningham

Peak Quany has achieved substantial improvements to its bottom lie by giving close attention to blasting practice, and in pr@icnlar by introducing electronic delay detonators for routine production blasting. The precision and flexibility provided by these units has enabled the quarry to gain control over fmes and curtail oversize without increasing explosive usage. In addition, the extent of nuisance from blasting vibrations has been reduced.

Jan 1, 1998

By Chulgi Suk, Hoon Park, Hyonsoo Kim, Hakman Kim, Sangho Cho

Dust emission from blast demolition and other construction activities can be a nuisance; it is widely recognized that fine particles less than 10 µm in equivalent diameter (called PM10) may cause health problems. Mist spray systems, such as rain guns, sprinklers, water/surfactant sprays (or foams) etc., are some of the most effective dust suppression methods. A large amount of research has showed that when water droplets are produced in an equal amount to that of dust particles, the airborne dust is suppressed by the agglomeration of dust and mist particles. A method for generating micro-sized mist from water, achieved by the detonation of explosives in the water tube, was suggested and is called the ‘detonationdriven water bag burst system’. There are many experimentally observed limitations of the explosioninduced water break-up process. The water bag explosion tests were simulated using the AUTODYN software, in order to investigate the aerosolization mechanisms of the detonation-driven water and water break-up process into micron-sized droplets. As a result of the numerical analyses, the diffusion direction of water when detonating in the central interior part of water tube was radioactive and significantly stronger than when detonating in the bottom exterior part; this is due to the compressive flow of the volume change inside of the water tube, which resulted from the blasting wave inside of the tube, as well as the reflected pressure on the ground. Blast tests of full-scaled reinforced concrete columns were conducted to verify the effectiveness of the suggested detonation-driven water bag burst system. The water breakdown and dispersion that occurred while blasting the reinforced concrete columns were observed using a high-speed camera, and dust generation was monitored using four density detectors. The suggested detonation-driven water bag burst system showed that the average dust density decreased by up to 7 mg/m3.

Jan 1, 2016

By Dean Nichols, Matt Ortel

Explosive accidents in the United States have brought increased attention to emergency operation plans (EOP) at all facilities that manufacture, transport, or store hazardous materials – particularly explosive materials. Explosions are sudden, powerful, and complex events that are difficult to characterize in terms of the thermal, over pressure, and debris effects. Industry, regulatory, and public officials require emergency response planners to not only anticipate the blast effects of an explosion, but also to prepare an appropriate response.

Jan 1, 2016

By Steve Colburn

The CRITERION Survey Systems utilize both theodolite mounted and hand held reflectorless distance meters. These are eye safe, easy-to-use, and specifically designed to endure the harsh environments characteristic to the mining, quarry and explosives industries. Survey data collected by the systems is digitally stored in a ruggedized data collector and then processed with a specialized, Windows-based, interactive software program which can be run on any standard PC.

Jan 1, 1997

By Stuart Brashear, Eddie Colburn

The Birmingham Coal and Coke – Knight Mine is a single seam coal mine in central Alabama. As pit development progressed in 2013, concerns over increasing vibration levels resulted in modifications to the blasting program that inhibited shot size and coal recovery. By January 2014, while still over 1,400 feet (427 m) from the regulatory seismograph, vibration levels climbed above 70% of the mine permit limit, even with triple decking of holes and reduced burden and spacing. At this time the decision was made to commit to the use of signature waveform analysis and precision programmable electronic detonators to minimize vibration and maximize the amount of coal that could be recovered before vibration levels reached permit limits.

Jan 1, 2015

By G. Adderley, A. Wetherelt

The problems of poor drilling in underground operations have been highlighted on many occasions. Incorrect collaring and poor angular deviation can all lead to an increased block size, dilution, over-break adding to both cost and time, while in a tunnelling operation sidewall damage and a poor percentage pull from a blasted round has similar consequences. This paper sets out to further investigate the ability of the laser scanner method of obtaining drill hole deviations and collaring errors at the face as described by Wetherelt and Williams (2006). Tests were carried out to compare measured inter-hole burdens from this method in comparison to that obtained using a total station survey. To investigate the ability of these methods to accurately determine drilling errors, a field test was carried out through an analysis of a series of pre-drilled blast holes of known inclination and direction. A time-motion study was also conducted for a varied number of holes to assess the usability of each method. In line with current research into blast vibration being undertaken at the Camborne School of Mines, 6 cut blasts were carried out to establish the effect of poor drilling on a blasts success to see whether an increased burden at the toe of a hole had an influence on vibration.

Jan 1, 2009

By Ali Kahriman, Abdulkadir Karadogan, Umit Ozer, Mehmet Aksoy, Kagan Ozdemir, Adiguzel Deniz

This paper presents the results of ground vibration measurements induced by blasting during the construction of the Istanbul Kadiköy-Kartal metro tunnel which has been driven at a depth of approximately 20-40 m deep under a highly urbanized region of Istanbul city in Turkey. This tunnel is being constructed by a joint venture group. The formation encountered during the construction is classified as hard and strong rock by laboratory and field tests performed by the joint venture group. Within the scope of the study, for the prediction of the peak particle velocity and to determine the slope of the attenuation curves together with the maximum charge per delay for the S4 shaft tunnels and S12 shaft tunnels of this tunnel route, ground vibration components were measured carefully by using four vibration monitors (Instantel Minimate Plus model) during the advancement of the tunnels which required blasting. The particle velocities and frequency values of all blast events are evaluated according to the United States Bureau of Mines (USBM) and German DIN 4150 Norms in order to predict, and compare the influence grades to the neighbouring buildings, and structures. Also, data pairs of scaled distance and peak particle velocity obtained from 114 records at S4 shaft tunnels and 79 records at S12 shaft tunnels were analysed statistically. Empirical relationships with correlation at the 95 % confidence interval were established for different rock units (diabase and arkose) and suggested for the test sites in order to estimate particle velocity of the ground vibrations.

Jan 1, 2007

By Gary Cavanough, Stuart Addinell, Hector Parra

Drilling deep, straight, accurate holes in hard rock to achieve efficient blasting is a challenge for the mining/quarrying industries with short holes normally drilled using “top hole hammer” (THH) and deep holes using “down the hole Hammer” (DTH).

Jan 1, 2013

By P D. Katsabanis

The dynamic tensile strength of geomaterials is known to be highly dependent on the strain rate of the load applied. This is significant in applications where the material is subjected to shock waves and impact loading. This paper proposes the use of a simplified method to determine the dynamic tensile strength of hard brittle rocks using an explosively impacted version of the Hopkinson Pressure Bar. A compressive stress wave was propagated in a sample, representative of the material of interest, by detonating a small charge at one end of a cylindrical sample. The tension wave, generated upon reflection at the free face, causes spalling in brittle materials. Strains at four points in the specimen were continuously measured and the dynamic tensile strength was determined by applying the one-dimensional wave theory.

Jan 1, 2010

By R. Franfield

This paper describes a situation that many drilling and blasting contractors have found themselves in – a client?s fear of the use of explosives. In the summer of 2007 Blasting Services Ltd was asked to undertake some drilling and blasting work in an abandoned quarry that was being restored for a housing development. Previous quarrying operations had left a series of overhangs that were considered unsafe and required removing. The site contractor considered that the best and safest way to carry out this work was by drilling and blasting. Blasting Services Ltd, with the technical assistance of Exchem Explosives, designed a drilling and blasting regime to accomplish this work with a series of trim blasts. The design took into account the close proximity of a structure in very poor condition and the imposed vibration limit of 6.0 mm/s (0.24 i.p.s.). The faces were profiled, holes drilled and explosives ordered. A few days before the first blast was due to be carried out the client decided that the poor condition of the nearby structure meant that the use of explosives could not be permitted. This decision was made despite the blast design indicating that the vibration level would be well below the 6.0 mm/s (0.24 i.p.s.) limit.

Jan 1, 2009

By Gordon M. Matheson, Douglas A. Anderson, David K. Miller

"Traditionally, analysis of vibrations from blasting has been focused on peak particle velocity fordetermining the likelihood of both annoyance and damage. The US Bureau of Mines, in RI 8507,indicated the importance of frequency in vibration. Methods of controlling the vibration by reducingthe vibration concentrated in certain frequency bands using delays have been successful over the past decade."

Jan 1, 1997

By Roberto Folchi, Hans Wallin

Having so many norms and technical content of legislation to deal with is a problem that an explo-sives engineer has to face, especially when working at an international level. Each country has its own norms and legislation, sometimes even each other region or state, as if the physics of explo-sions, rock, concrete, and masonry characteristics would change across the borders. Both norms and laws are frequently out of date, being mainly developed at the beginning of the previous century and adjusted, piece by piece, to a technical and political context that is constantly changing, with adjustment being frequently adopted in a hurry, due to a problem arising such as that of internation-al terrorism. Sometime also, norms are not harmonized with those they intend to amend, so required explanations and new adjustments lead to a vicious circle that increases confusion, complexity and depresses the explosive industry.

Jan 1, 2015

By Patrick D. McLaughlin

Crater blasting techniques have had relatively little application in the surface mining industry. This is not surprising, considering the geometry required to efficiently use cratering. The more widely known blasting operations that employ some form of cratering are listed below.

Jan 1, 1992

The objective in control blasting is to reduce overbreak to control the final pit wall slope, shaft, drift, ditch, bench, etc. to the final planned excavation limit.

Jan 1, 1990

By Jack Eloranta

This paper documents the relationship between material handling and processing coete compared to blasting cost. The old adage, "The cheapest crushing is done in the pit", appears accurate in this c!ase study. Comparison of the accumulated cost of: powder, selected wear materials and electricity; indicate a strong. inverse correlation with powder factor (lbe powder/long ton of rock). In this case, the increased powder cost is more than offset by electrical savings alone.

Jan 1, 1995