Search Documents

By Petr Mostak, Miroslav Horacek, Miroslav Stancl

Detection of plastic explosives is an important task in the security measures against criminal misuses of this type of explosive. Particles and vapour detectors are basic instruments in this detection. Colour reactions and dogs are also used. Marking system in accordance with requirements of Montreal Convention was developed and applied in full scale production of plastic explosives including Semtex since 199 1. The influence of marking on technology, performance and other properties of plastic explosives is discussed. 2,3 dimethyl 2,3 dinitrobutan is the most popular marking agent which is broadly used. The detectability of this compound is not optimum by some detectors. The substantial effort has been given to development of plastic explosives with controlled shelflife. Some results of this work are presented. Technical and economic aspects of identification marking are discussed.

Jan 1, 2001

By David E. Siskind

In the period 1989 to 1994, the U.S. Bureau of Mines assisted the Office of Surface Mining, Reclamation and Enforcement (OSM) in studying a high-complaint situation near an active surface coal mine. As part of a review for its project report, the Bureau had to address issues on the adequacy of the safe blasting criteria and analysis procedures in its 1980 report RI 8507, Structure Response and Damage Produced by Ground Vibration From Surface Mine Blasting.

Jan 1, 1996

By R. K. Wharton, G. H. Pickering

The paper reviews the explosives products that have been certified by the different Explosives Notified Bodies for sale in European Union countries. The development of harmonised standards for explosives is also discussed as are recent developments relating to certification and a possible forthcoming Directive on pyrotechnic articles.Copyright

Jan 1, 2004

By Kenneth Faroni, Catherine Aimone-Martin, Thomas Gelormino

A blasting improvement program began in 1985 at two traprock quarries in Connecticut to reduce the levels of ground motions and airblast measured at residential structures surrounding the operations. The quarries are situated within town limits, adjacent to a number of historical and other structures. Although blasting vibration amplitudes were found to be far below those that could produce cosmetic defects in structures, they were perceived to be the cause of structural defects observed by homeowners. Based on a comprehensive * review of blasting practices in place during1985, an extensive vibration monitoring program was implemented. The initial study included the instrumentation of selected residential structures to record and analyze strains imposed within structures from quarry blasting, environmental changes, and from daily household activities. A comparison of the results was made with the results reported by the U.S. Bureau of Mines in 1980. The highest strain imposed in drywall from blasting (13 J_I strain) was 12% and 1% of the highest strain levels recorded for normal household activities and temperature changes, respectively. The present philosophy in production blasting is to attempt to keep vibration amplitudes as low as practical by implementing state-of-art blasting control techniques. Currently, blasting seismographs are placed in a circular manner around each quarry, providing production blast vibration records for 360 degrees of coverage at distances of 2500 to 4000 ft. from blasting operations. Seismograph and production blast records are analyzed each year and become part of a Blasting Improvement Plan submitted to the local zoning commission as part of the annual operating permit process. This paper summarizes the results of previous vibration monitoring programs and outlines the modifications made to blasting practices to minimize the levels of ground motions and airblasts. The public relations efforts and standard corporate procedures used by company personnel to address all blast related complaints and alleged damage claims since 1985 are also discussed.

Jan 1, 2000

By Jesus Pascual, Jose Sanchidrian, Pablo Segarra

The surface vibration field in the area above an underground mine prior to its development has been investigated, in order to assess the vibration levels expected in existing buildings and in the planned mine facilities from future underground blasts. Shots of 50 and 100 kg of explosive placed in drillholes at depths of 100 to 150 m were fired, and the vibration events were recorded using an array of 40 seismographs in a 400 m square grid, covering a 2×2 km area. Contours of isovelocity were obtained for each shot, showing some directional transmission patterns. Propagation laws were obtained from the results of each shot and also from the bulk of data, both for the whole area and dividing it into four quadrants. The shift of dominant frequency with distance was also analyzed.

Jan 1, 2002

By Robert B. Hopler

Explosives have been important to the oil and gas industries since the very earliest days. The first wells of Pennsylvania and New York in the 1860’s were able to be brought back to productivity by the use of nitroglycerin after their porosity was lowered by the high para& content of their oil. Success in the use of seismic waves to locate enemy artillery in the First World War led to the use of explosives in the 1920’s for generating ground vibrations to locate geological structures favorable for the entrapment of oil. Explosives also find widespread use in the more conventional applications of well site preparation and pipeline construction. Explosives applications unique to the oil and gas industries include the jet perforating of casings and formations, fighting well fires, and cutting casing during well shut-in.

Jan 1, 1998

By Ricardo Chavex, Adrien Letellier

Flyrock remains one of the most critical issues in open-pit blasting. Despite the significant improvements made with modern surveying methods, the necessity remains to define sensible danger zones around blasting areas. Therefore, many semi-empirical models predict flyrock distances based on trajectory calculations and probabilistic adjustments. However, most are merely based on nominal parameters, even though a considerable amount of precise data is nowadays available thanks to modern measurement techniques using lasers, GPS, drones, and probes. These data provide accurate information about the actual field circumstances of a blast concerning geometry and rock-mass conditions. So how can we use and integrate them into existing flyrock models? The answer to this question can significantly improve the accuracy of flyrock prediction models and enhance safety. This paper will present a method to adapt existing models to actual field data using appropriate software and digital tools during the blast design process. In addition to calculating a more pertinent danger zone perimeter, this method provides an efficient and practical tool that helps prevent flyrock incidents. Indeed, it allows the blast designer and shot firer to be warned if there is a hazardous critical deviation due to local conditions. Moreover, it also enables blasters to communicate better and share the visualization of the blast-specific evacuation zone. The paper will also discuss how this method can be calibrated and how it has been used to analyze some actual flyrock incidents.

Jan 21, 2025

By Hairong Zeng, Shahram Tafazoli, Edmond Chow

Blast fragmentation is one of the main parameters for optimizing mineral processing, but reliable data is difficult to acquire, resulting in unpredictable performance and efficiency. Crusher and grinder circuits are designed to process specific rock size ranges. Oversized rocks require extra energy to reduce before feeding into the process, and undersized rocks indicate that the process is not used to its full extent. Blast design is the key to controlling the blast fragmentation, so the ability to accurately monitor the particle sizes is imperative.

Jan 1, 2011

By William C. Burkle

In this paper, the author has cited essential areas in which the explosives engineer can assist the mine manager in his planning of an entirely new operation or in a major expansion of an existing facility.

Jan 1, 1990

By Guillermo Silva

A novel, ultra-low density explosive composition, particularly suited for wall control and other applications requiring customising of the explosive’s energy output, has been developed. Being reactive in nature, the low density explosive enables the controlled dilution of dry blasting agents from their nominal densities down to values slightly less than 0.10 g/cm3. The product has been detonated at densities of 0.07 g/cm3 in diameters as small as 50mm under confined conditions, using a 227 g (l/2 lb.) primer. Recorded velocities of detonation ranged between 1200 m/set and 2200 m/set for densities between 0.07 and 0.2 g/cm3. Theoretical velocities ranged from 1700 m/s to 2500 m/s for the same density range. The low density explosive was insensitive to initiation by a blasting cap which is a desirable feature for transportation purposes. Mixing of the product with ANFO has been accomplished with minimum segregation making it suitable for applications where reduction of pressures are necessary.

Jan 1, 2000

By Earl C. Hutchison, Gene Smith

Extensive blasting was required to construct an underground tunnel for a 90 inch sewerage relief line. The tunnel and required excavation extended under an upper middle-class residential area in Atlanta, Georgia for more than a mile and a half and required the use of more than a half million pounds of explosives in the immediate vicinity of houses and residential apartments valued at more than 16 million dollars. Other houses and property valued at more than 80 million dollars were within range to claim blasting damages. An effective blasting damage control program was carried out which limited the number of blasting damage claims to less than 2-1/2% of the total number of potential claims. All but three of the small number of blasting damage claims which were made were effectively denied without any resulting legal actions and less than $3,800 was paid for settlement of the three claims.

Jan 1, 1981

By Robert B. Hopler

Hercules Incorporated has designed, developed, and begun introducing a new non-electric delay blasting cap system which is radically different from anything presently available. This system, called Hercudet™, utilizes no wires or detonating cord. Instead, each cap has two plastic tubes attached to it. These tubes contain no coating or other materials other than dry nitrogen to extend storage life. In use, after connecting the tubes together with external sleeve connectors, the circuit is checked with a specially designed tester. When the blast area is cleared, the circuit is filled with a gas consisting of an automatically proportioned mixture of fuel and oxidizer gases. When the circuit is fully charged the gas is initiated by special means within the Hercudet™ blaster. The reaction that then travels throughout the circuit has no distruptive effect on the tubing, and virtually no noise is produced.

Jan 1, 1975

By Alastair Torrance, Gary Cavanough

Over the past two years a research project has been performed on reactive and hot ground. A key finding is that host materials including carbonates and coal are inhibitors to the reaction of sulphide and nitrates. The mechanism of this inhibition is pH buffering and isolating the surface of sulphide from reactants. It has been identified that acidity is a key driver of the reaction with a pH of 2 required for a reactivity event. A series of decomposition experiments confirmed that reactive and hot ground are essentially the same phenomenon with the heating produced either by the reaction of sulphide with nitrates or an external heat source. The results indicate that the key driver of detonation in reactive ground is energy and heat released from the acid induced reaction of sulphide and nitrate with no indications of sulphide being a catalyst or contributor to detonation apart from being a heat source. There must be sufficient sulphide and thermal insulation to provide and retain enough heat for detonation to occur. A pathway to detonation is postulated whereby the heat travels upwards and results in evaporation of water in the explosive. When the temperature reaches approximately 200°C (400°F) the ammonium nitrate starts to decompose, decreasing the mass of the reacting species. The material in the top layers has reduced density and specific heat hence the temperature of the top region rapidly increases up to >1000°C (1800°F) and may initiate detonation. Field tests on loaded blast holes support this proposed mechanism. Case studies are presented whereby the research findings are used to provide an analysis of historical reactive ground events.

Jan 21, 2025

By W. Birch, G. D. Rangel-Sharp, L. Bermingham

For many years, the accepted method of Measuring the Velocity of Detonation (VOD) in blast holes has been to use an electric cable of a constant resistance per metre. Thus as the wire is consumed by the explosive in the blast hole, the change in resistance is monitored and when this data is plotted against the time period of the in hole explosion, the VOD can be calculated.

Jan 1, 2011

By John T. Aler

The U.S. Bureau of Mines has been studying the problem of why explosives detonate weakly or misfire during blasting in underground coal mines. Cross-borehole shock wave interaction has been identified as a predominant mechanism causing explosives to function improperly (1)(Underline numbers in parenthesis refer to items in the list of references at the end of this report.). Cross-borehole shock wave interaction can be simulated in a laboratory setting, making possible the replication of tests in sufficient numbers to understand and quantify some of its effects on permissible explosives (2). The work presented here investigates the capacity of explosives to partially recover from the desensitizing influence of the shock wave. The recovery trend of different explosives can indicate optimum blasting patterns useful for minimizing borehole charge malfunctions.

Jan 1, 1991

By Jose Pineda, Abraham Lindo

The Panama Metro System’s Network expansion involves excavating a launching shaft for a tunnel boring machine (TBM) to traverse beneath the Panama Canal. The blasting needed for this shaft construction poses significant challenges due to the presence of concrete walls encircling the excavation. These walls must remain intact throughout construction and the tunnel's future operation. This case study is focused on devising and implementing safe blasting techniques crucial for the shaft's construction, ensuring the preservation of surrounding concrete walls and project equipment. As the interest was potential damage to the concrete walls, an appropriate vibration threshold for this project was also required as an alternative to the traditional U.S. Bureau of Mining RI-8507 limit (USBM RI8507). Blast modeling software was employed to conduct a series of blasting simulations. Parameters like hole diameter, spacing, depth, explosive type, and initiation methods were varied to evaluate their potential effects on wall stability and damage risk. The simulations revealed that smaller diameter holes and reduced spacing between blast holes would effectively mitigate the risk of wall instability. Additionally, utilizing electronic delay detonators and carefully planning the blast hole detonation sequence proved critical in minimizing potential damage. Executing these blasts in the field presented unique challenges, including strict charge per delay thresholds and logistical constraints. Consequently, continuous adjustments to blasting parameters were made and comparative result analysis. Beyond providing a safe blasting strategy for the TBM launching shaft, this study offers invaluable insights into adapting blasting designs to align with environmental and structural safety standards. These findings hold great potential to shape guidelines for analogous sensitive construction projects. They underscore the importance of leveraging prior research as a reference point, engaging with project designers and local authorities, and continually conducting testing and adjustments to ensure project success.

Jan 21, 2025

By Tie-jun Tao, Ming-sheng Zhao, En-an Chi

"Karst landform is a special kind of geomorphic unit which is often accompanied by a large number of geological defects: caves. In blasting engineering, if there are karst caves around the blast-holes, it may result in higher boulder yield and the generation of flying rocks due to the change of burden which is very hazardous for the safety of surroundings. The models of rocks with karst caves from blasting holewere built by the software of ANSYS/LS-DYNA. The results of computation simulation show that thecave can increase more free surface for blasting and leads to a broken zone around itself. Thus rockmass around the cave will fly toward inside and it will result in undesirable result of whole rock mass to be blasted. In addition, the models of rocks with karst caves in different shapes were simulated and thecomputation results show that the caves in round shape have higher load resistance capability than that the caves in rectangle shape. All the simulation results can offer effective guidance for blasting design. The models of rocks with karst caves were built in different distances and shapes from blasting hole by the software of ANSYS/LS-DYNA. The effect of different karst caves on blasting stress and blastingresult were studied."

Jan 1, 2017

By M. K. Ameen, R. El-Hacha

This paper presents the analytical results obtained from numerical simulation of reinforced concrete slabs strengthened with various FRP systems and subjected to blast loading. A three-dimensional finite element model using AUTODYN software was used to predict the overall behavior of the slabs. The numerical results were validated by comparing with experimental results from a program carried out to investigate the efficiency of different strengthening systems on the blast resistance improvement of small-scale reinforced concrete (RC) slabs. The experimental program consisted of testing nine RC slabs strengthened with three different externally bonded (EB) FRP systems attached at the bottom side of the slabs and one RC slab tested without strengthening for comparison purposes. The EB FRP strengthening systems investigated included two layers of Carbon Fiber Reinforced Polymer (CFRP) sheets, two layers of Glass Fiber Reinforced Polymer (GFRP) sheets, and one layer of Glass-Fiber Resin Polymer (GRP) sheet. Different epoxy resin, patching mortars and impregnating epoxy adhesives were used for the slab surface preparation and FRP system application of the strengthening layers. The aim was to evaluate the residual strength of the test specimens after exposure to blast loads. The blast loading parameters were evaluated for each test using AUTODYN simulation and compared with the computer program CONWEP. All specimens were subjected to same spherical TNT charge weight and stand-off distance with the respect to the slab top surface. Extensive comparison is made between the experimental results and the AUTODYN simulations for the control unstrengthened slab and the strengthened slabs including time history records of the bottom steel strain and mid-span acceleration and the peak dynamic deflection of the slabs.

Jan 1, 2010

By Randall M. Wheeler

Pre-blast surveys are used to document the condition of a structure prior to the commencement of blasting activities. They provide the best means of determining the pre-existence of visible cracking and deterioration in a structure before blasting is initiated. A small investment in a good pre-blast survey, coupled with good public relations, could mean a large cost savings for a company in the future.

Jan 1, 1992

By Anders Lagerkvist, Agne Rustan, Tommy Edeskar

Landfills containing house hold waste produces methane gas during its decomposition. This gas can be recovered and used for heating purposes or as fuel for vehicles. Gas drainage pipes are installed in the landfill and connected to a central suction point. Methane gas is produced over several years until the slots in the drainage pipes are clogged by black mud. And the bottom of the vertical drainage pipe are filled with mud and water. The hypothesis tested in this paper is if blasting in the drainage pipes could activate the production and flow of methane. In the first part of the paper we have studied what maximum linear charge concentration could be used in different size of PE-pipes place vertical on surface and surrounded by air. The results show that the maximum linear charge concentration for single blasts varied between 5-10 g/m, depending on the diameter of the pipe (90, 100 and 160 mm). Maximum charge concentration for the repeated blast varied between 2-5 g/m. In the second part of the paper we study what maximum linear charge concentration could be used in situ for full scale blasting tests in a special prepared test area which later on was dug out after the blastings. Up to 40 g/m could be used without damaging the top of the 160 mm diameter pipes. The increase in methane flow was so low so it could not be measured c4.5 m3/h. The conclusion therefore is that the stimulation of methane flow by explosives is not enough.

Jan 1, 2000