Search Documents

By A. S. W. Kurny, M. Z. Huq

Bangladesh ilmenite is partially altered, containing pseudorutile, rutile and haematite as well as the predominant ilmenite phase. A typical analysis is 39.45% TiO2, 24.19% FeO and 33.0% Fe2O3. Reduction of the ilmenite by charcoal was found to involve two major reactions: conversion of pseudorutile into ilmenite and rutile, and change of ilmenite into metallic iron and rutile. The first, which was much the faster reaction, was responsible for an initial increase in ilmenite content with reduction time at lower temperatures. Apart from these two major reactions, rutile was reduced to lower oxides at 1 100 degrees C with a consequent decrease in its XRD peak height

Jun 19, 1905

By Frederick H. Raab

An electromagnetic (EM) system for the location of trapped mine workers at coal-mine (300 m) depths has been developed. The use of such a system in deep mines (1-km depth) requires transmission at extremely low frequencies (ELF) and a reduction in the effective noise level beyond that which can be obtained by acceptable Integration times. Automatic-noise-cancellation (ANC) techniques reduce the effective noise level by combining several received signals that contain correlated noise. Such signals can be obtained either from a remote magnetic antenna or a local electric antenna. During Phase III of this program, real ELF noise data were acquired and used to test the ANC algorithms developed during Phase II. The ELF noise data were obtained from analog recordings made by Develco under another Bureau-of-Mines contract. Digitization was accomplished by an ND converter that was added to a GMRR computer. Phase III tasks Included preparation of software for digitization, computer-computer communication, data processing, and statistical analysis. Useable data were obtained from eleven half-hour tapes containing noise from one axis of the primary antenna and three axes of the remote antenna. The overall average Improvement in SNR was 4.1 dB. However, the average Improvements for the Individual X, Y, and Z axes were 4.2, 11.9, and -1.9 dB, which roughly follow the observed noise power. Nonlinear processing was not effective with this noise.

Jan 2, 1984

By M. A. Hammer

In this study by the Federal Bureau of Mines Pennsylvania anthracite from the Eastern Middle field was oxidized by concentrated nitric acid at steam-bath temperature for 24 to 1,000 hours. The quantitative data obtained include yields of nitric-acid soluble and insoluble products and the distribution of carbon and ash in each. The acid-insoluble residues were examined for solubility in aqueous sodium hydroxide. With a sodium hydroxide concentration of at least 1 normal, a portion of the residue could be extracted in the form of a true solution. With lower alkali concentrations, peptization occurred. Alkali solubility of the residue increased with length of oxidation. However, when expressed in percentages of original coal weight, the alkali solubility remained essentially constant after 192 hours of oxidation. This suggests that the alkali-soluble products are converted to acid-soluble products at the same rate as the original coal substance is converted to alkali-soluble material. Microscopic observations of the peptization of the acid-insoluble residues revealed a gross micellar physical structure. The action of nitric acid is apparently not restricted to the surface of a coal particle. The acid penetrates the particle through the pore structure, dissolving some of the ash and altering the bonds between the coal micelles. The bond alteration, as indicated by ultimate analyses, involves the physical and chemical adsorption of the components of nitric acid. Some of the altered bonds are not thermally stable; this instability is shown by the complete loss of peptizing ability when the acid-insoluble products are heated above 200° C. This loss is accompanied by the evolution of water, oxides of nitrogen, and hydrocyanic acid.

Jan 1, 1961

By Kim B. Shedd

An initial evaluation of the flow of cobalt-containing materials in the United States was prepared. The following aspects of materials flow were included: cobalt released as a result of mining and processing other metals and minerals; scrap generation and subsequent recycling or cobalt recovery; and cobalt losses resulting from the generation of wastes, dissipative uses, and disposal of used products. Where possible, estimates were made to quantify the amount of cobalt lost from the materials flow. More than 2,000 metric tons (mt) of cobalt are released annually from mining and mineral processing in the United States, including 480 mt of cobalt in coal produced in the United States. Metallurgical industries examined in this study have well-established recycling or cobalt recovery practices. The petroleum industry recycles spent catalysts, and some chemical catalysts are also recycled. Losses generated during cobalt chemical and powder processing were estimated at 50 to 80 mt of cobalt annually. Losses from alloy processing and the manufacture of parts and products were estimated to be 360 mt. These industrial losses are greatly outweighed by an estimated 2,780 mt of cobalt' consumed in the United States each year to make products that will ultimately be disposed of.

Jan 1, 1992

By Sheridan J. Rodgers

The quantity and behavior of gases in metal and nonmetal mines were monitored to provide background information on feasibility of incipient fire detection systems. Monitoring was conducted during working and nonworking periods at intake air, return air and working places. Gases generated during diesel operations and shot firing were of particular interest. Gases which were monitored were CU, C02, N0, N02 and S02: submicron particulate concentrations were monitored also. Commercially available instruments were used and included nondispersive infrared, electrochemical and chemiluminescent types. The ratios of the various gases generated during diesel operations and shot firing were similar to those expected from an incipient fire, with the exception of the C02/NOx ratio, which is sufficiently different to be considered for early fire warning. Samples taken near leaking bulkheads showed high C02 levels and low C0 levels, the reverse of anticipated behavior in coal mines.

Jan 1, 1976

By Lawrence K. Barker

Crude shale oil produced by underground retorting of Green River Formation oil shale was hydrogasified over a cobalt-molybdate-on-alumina catalyst at operating temperatures ranging from 800° to 1,300° F, pressures of 500, 1,000, and 1,500 psig, and a liquid hourly space velocity of 1.02 volumes of oil per volume of catalyst per hour (Vo/Vc/hr). At a temperature of 1,300° F and pressure of 1,500 psig, 94 weight-percent of the liquid feed was converted to gas containing 72 volume-percent methane. With two reactors in series at a temperature of 1,170° F in reactor 1 and 1,260° F in reactor 2 and a pressure of 1,500 psig, 97 weight-percent of the liquid feed was converted to gas with a methane content of 75 volume-percent. Liquefied petroleum gas (LPG) was hydrogasified at operating temperatures ranging from 500° to 1,400° F at a pressure of 500 psig over a cobalt-molybdate-on-alumina catalyst. Similar experiments were made with an empty tubular reactor. The data indicate that gasification reactions in the presence of a cobalt-molybdate catalyst change from predominantly a catalytic (carbonium ion) reaction to predominantly a thermal (free radical) reaction at temperatures greater than 1,100° F. The data also indicate that a reaction temperature of 1,350° F is necessary at the space velocities used in this investigation to make a synthetic natural gas (methane content of 90 volume-percent) from in situ crude shale oil.

Jan 1, 1975

By T. A. Raczek

Materials for stronger ventilation tubing for underground use in hardrock mines were developed. The new material composites were evaluated in performance characteristics and compared to currently used materials. The materials were compared on tear, tensile, puncture and flammability properties. Based on cost versus performance data, a polyester film bonded to a polyester fabric was selected as the candidate material for field testing. Ventilation tubing fabricated from the selected material was field tested in two underground uranium mines for four-month periods. The test results indicated that the new composite showed an increase in useful life in the majority of applications, However, the cost performance ratio was not significantly improved to warrant commercialization of the product. When connected directly to some blowers, the material in close proximity to the blower deteriorated. However, material which was punctured or torn by mechanical means did not have further propagation of the tear. The high tear strength of the material prevented further damage. Improved methods of repairing inflated ventilation tubing were investigated and developed. All the repair methods were portable and self-contained. Repair kits based on adhesives, pressure sensitive tapes, and mechanical means were evaluated. Plier staplers and patch systems based on pressure sensitive adhesive proved to be most functional.

Jan 1, 1980

By R. Tyreman, G. Ritson

"The Red Lake Mine is situated in Balmer Township, Red Lake area in northwestern Ontario. It is an underground mine that has been in production since 1948. The property was originally known as the Dickensen Mine and was shut down in 1996.A feasibility study was carried out in 1998 and it was determined that a new mill should be constructed with a throughput rate of 600 stpd. The life-of-mine average gold grade was projected to be 1.35 oz/t with gold predominantly associated with arsenopyrite and pyrite. Metallurgical testwork indicated that the optimal flowsheet for gold recovery would include an autoclave for oxidation with a carbon circuit for adsorption. To limit capital cost and establish cashflow, the mill was constructed without an autoclave. The recovery by gravity and cyanidation was projected to be 83%. A flotation plant was constructed at the tail end of the circuit to recover the additional gold associated with sulphides from the leach circuit tailings. This material is being stockpiled onsite for future oxidation treatment.Detailed engineering was started in early 1999 and the first gold was poured in August 2000. One feature of the project was the use of Contact Lake equipment from Cameco’s Contact Lake project. The entire mill was purchased and equipment re-used where possible. The capital cost for the process facilities was C$3 1.5 million."

Jan 1, 2001

By William S. Heckman

a. When to use: high surcharges, vertical capacity required, limit noise and eliminate vibrations, low headroom, eliminate vibration induced settlements. b. Advantages: eliminates impact noise and vibrations, high section modulus if required, vertical load bearing capacity; corrosion resistant, easy to apply facing for use as a permanent wall, adapts to complex wall layouts, would allow top- down construction, very high uplift resistance. c. Disadvantages: spoil disposal, not water tight, cannot penetrate rock and most obstructions, soil can erode between the piles if surface water and ground water are not controlled, hard to install reinforcing beams over 409 long; subject to high negative skin friction loads, high grout takes in rubble and organic soils. e. Relative cost to other systems: 30% to 50% more expensive than driven soldier piles and lagging except when surcharge loads are involved, or the pile cannot be driven due to noise and vibrations. About the same cost as a sheet pile system. Very competitive if high vertical load must be supported by the wall.

Jan 1, 1997

By Mark Sanders

This report describes an experiment which was conducted to compare the relative bumping hazard of a low and high profile hard hat (helmet) in a low seam mining environment. The study was specifically designed to assess the effect of lowering the helmet profile on frequency of head impacts in an underground low seam coal mine simulator. This involved subjects performing four common low coal mining tasks wearing the low and high profile helmets in the low seam simulator (36" and 48? heights). The results of the study indicated that a low profile helmet could reduce bumping frequency in underground low coal approximately 25%, and as much as 80% on selected tasks. It was beyond the scope of the study to measure the impact force, thus it was not possible to estimate the effect of the low profile helmet on severity of impacts underground. The research team recommended that a more extensive investigation be made of head injuries experienced in low seam mining (both underground and surface) with the objective being to assess the impact of a low profile helmet on total head accident exposure.

Jan 1, 1980

By Bruce Rock

A continuous mining machine was redesigned for the installation of an integrated illumination system. The illumination system was designed by first calculating the theoretical number of luminaires required to meet the Federal Illumination Standards. Luminaires initially were placed using isointensity diagrams. A darkroom was used for "fine tuning" and demonstrating that the system met the illumination requirements. The luminaire mounts were installed on a machine underground. The performance of this illumination system was monitored in the working environment of an operating coal mine. Design changes were made as necessary during this evaluation period to improve the system.

Jan 1, 1979

By V. Svalbonas

When the Trelleborg Divisions of Boliden Allis and Mineral Processing Systems (MPSI) merged, a unique opportunity occurred for two independent mill fabricators to compare design pro¬cedures and the research upon which they were based. Several semiautogenuous (SAG) mill analyses are compared using Boliden Allis and MPSI methods. The differences and similarities are then used in a correlation of critical stress definitions and the acceptable design and inspection criteria. Given the opportunity to compare the total philosophies and methods of several companies involved in the design and fabrication of grinding mills, it was important to first develop the comparison method and ground rules. One option was to compare analytical methods by details such as numerical techniques and accuracies. However, this option was discarded in favor of a more general approach. The question that was finally posed was in two parts. Given an identical mill requirement: • What would be the difference in the analytical design result, and to what aspect of the analytical process could this difference be attributed? • What would be the difference in approaches to obtaining the final hardware in subcontracting, both in specifying and Quality Assurance surveillance? By using this comparative approach, questions of relative conservativeness and reliability would automatically be answered.

Jan 1, 1992

By B. M. England, M. V. Swain, N. Bristow, R. D. Dukino

The toughness and fracture mechanisms of ores with significantly different microstructures from Yandi, Koolan and Mount Whaleback were studied with a view to understanding their degradation behaviour. Bulk fracture toughness was determined by the 3-point single-edge notch beam test and the results interpreted using Weibull statistical analysis; indentation fracture mechanics was also used to measure fracture toughness of the different mineral forms and to understand their response to contact fracture

Apr 1, 1995

By Marcel Vanpee

Eight extinguishing powders KCI, were tested on five types of diffusion flames. The effect of flame temperature on the inhibition efficiency was investigated by varying the oxygen index of the flame supporting atmosphere. Inn addition a spectrographic investigation of powder flame dissociation products was carried out on the methane/air/ABC (NH4H2PO4) flame. Dissociation products for this flame included P0, PH, NH, and Na. It is concluded that the main factor to be considered in the efficiency of tie powder is the flame temperature Purple K (KHC03) was typically inefficient in low temperature flames and very efficient in high temperature flames. On the other hand, ABC (NH4H2PO4) was found to lose its efficiency at high temperature but to be quite efficient in the low temperature flames. The effect of temperature is offered as an explanation of the poor efficiency of Purple K (KHC03), against coal dust explosions as contrasted to the high efficiency of phosphate salts against coal dust explosions.

Jan 1, 1982

By R. L. Grayson

Focusing on relationships between severity measure versus productivity and other factors, this paper presents a comprehensive study of injuries for U.S. underground coal mines in 1996 by mine size. Based on analyses of data, generally the larger the mine, the more productive it is (in tons per employee-hour), but the more severe is its injury experience (r = 0.65). Within very large, large, and medium mine sizes, however, the more productive the mine, the less severe is its injury experience (r =-0.43, -0.36, and -0.26, respectively). For small and very small mines, a more deeply nested analysis is required to understand relationships. Other interesting relationships and comparisons are presented.

Jan 1, 2000

By H. D. Kline

This paper describes the methods of mining and washing brown iron are in 1957 at the Sawyer mine, leased by Wayne County Mining Co., and the Fore mine, leased by Four Mining Co., both in southern Missouri; it is one of a series prepared by the Federal Bureau of Mines on mining and milling methods and costs in various districts of the United States. The Sawyer mine is in Wayne County, about 10 miles north-northeast of Williamsville (fig. 1); the Fore mine is in Howell County, about 20 miles southwest of West Plains (fig. 2). Both are open-pit mines from which the crude are was upgraded by washing and hand-sorting to produce are of grade and quality suitable for sale to operators of iron and steel furnaces. The operations described are typical of many others that produce or have produced marketable brown iron are from small sedimentary deposits, several hundred of which outcrop on the crests or hill sides of southern Missouri (fig. 3). The 1957 production of marketable brown iron are by 40 separate operations in the southern part of the State was 281,427 wet long tons, valued at $1,637,243. Production from the Sawyer mine that year was 17,000 dry long tons of washed are, and from the Fore mine, 20,816 dry long tons.

Jan 1, 1960

By Geo. S. Krueger

This paper, describing mining methods and costs at the Judge mine Park City, Utah, is one of a series being prepared by the Bureau of Mines on mining practices in the United states. ACKNOWLEDGMENTS The writers acknowledge the assistance of E. D. Gardner, supervising engineer, Southwest Experiment Station, Bureau of Mines; Paul H. Hunt, mine manager, Park Utah Consolidated Mines Co.; Wm. Osika, chief mine accountant; and Eric Neilson, assistant master mechanic of the mine.

Jan 1, 1938

By Bruce Pinkston

This report presents a description of the Prototype Demonstration Vehicle developed under U.S. Bureau of Mines Contract No. JO 366003, "Improving Man Transit Safety". This vehicle was constructed to assess the feasibility of a set of equipment related guidelines which were drafted in Phase I of the same contract. State-of-the-Art improvements were embodied in such areas as collision survivability, occupant comfort, and multiple mode (on and off rail) operation. The electric battery-powered vehicle carries a twelve man section crew at speeds up to 12 mph. The description of the demonstration vehicle is presented in Volume I. Safety Guidelines are presented in Volume II.

Jan 1, 1981

By Spencee L. Willett

A sand and gravel deposit exists in the Wildrose Canyon Wilderness Study Area (WSA), Out it is limited to local use because of the distance from major markets and resulting high transportation costs. The WSA has no identified metallic minerals, oil, gas or other energy related deposits. INTRODUCTION The WSA encompasses 17,366 acres (7,028 ha) in the Panamint Range, Inyo County, California. Access to the area is by State Route 190, approximately 45 miles (72.4 km) east of Lone Pine, California and 16 miles (26 km) southwest of Stovepipe Wells, California (fig. 1).

Jan 1, 1983

By R. B. Schluter

Drying and preheating (partial induration) the green, unfired iron ore pellets is a means of reducing the energy required to produce metallized pellets. The Bureau of Mines processed three magnetite and two hematite concentrates through the unit operations of pelletizing, preheating in air, and reduction to metal to determine the effects of preheating upon the properties of the metallized pellets. The pellets were prepared in a 16-inch-diameter laboratory balling drum. Preheating and metallization were carried out in an externally heated 4-inch-ID by 4-inch-long stainless steel drum using air for the preheating atmosphere and lignite char as a reductant. The results 'varied considerably: two of the magnetites spalled when preheated in air at temperatures of 900° C and above, and the third magnetite and the hematite flotation concentrate required complete induration at 1,300° C to produce satisfactory pellets. The earthy hematite ore yielded excellent pellets at all preheat temperatures.

Jan 1, 1972