Search Documents

By I. Van de Voorde

In this paper, results are presented concerning the search to implement Supported Liquid Membranes (SLM) Technology for the recovery of copper, nickel and zinc from electroplating and other effluents to prevent metal waste. A study of the influence of the individual parameters and of their combined effect on mass transfer in small-scale laboratory equipment has been performed, enabling to set forward the appropiate operating conditions for a pilot plant installation. The SLM pilot plant has been tested extensively, including short and long term runs, with real process solutions. It was demonstrated that the SLM technolgy is applicable for solutions containing 800 mg/L of metal ions, but also to the treatment of solutions with low metal content of origin other than plating shops. It was demonstrated by system analysis that the recycled salts are usable to produce metal electrolytes (for example Watt's nickel bath).

Jan 1, 2003

By John M. Rapkoch

In the continuing search for copper matte converting methods, commercially available and feasible choices remain Peirce-Smith Converters, Hoboken Converters, Mitsubishi Converting, Ausmelt converting, and Outokumpu/Kennecott Solid Matte Oxygen Converting (?Flash Converting?). While each alternative improves on Peirce-Smith Converters? limited fugitive gas capturing capability, the Peirce-Smith Converter is relatively easy and economic to operate and has an unmatched ability to accept valuable but difficult-to-handle material such as scrap anodes and purchased scrap copper. Recent experience with designing, building, and starting up an ISASMELT facility, applied in primary smelting of copper concentrates, has led the authors to speculate on how suitable the ISASMELT process would be for copper converting, given its low fugitive gas release and its ability to accept a variety of feed types. This paper reviews the potential metallurgical challenges posed by converting copper matte in an ISASMELT vessel and considers possible engineering and design challenges posed by the inclusion of this technology into a new or refurbished copper smelter.

Jan 1, 2006

Most of the world's zinc metal is produced via the roast- leach-electrowinning (RLE) process. The process is well established, but most of the sulphur in the sphalerite concentrates reports in the acid, which has to be stored and/or sold. There are significant incentives to develop a simpler process with much reduced acid generation. Ferric ion is a well known oxidant for most sulphides, in particular sphalerite, and it converts the sulphide to elemental sulphur. Based on stoichiometry, however, the amount of ferric ion needed to achieve acceptable zinc extractions is prohibitive for downstream zinc recovery from the leach solutions. The process suggested here makes use of less-than-stoichiometric ferric sulphate additions because the ferric ion is regenerated by sparging SO2/O2 mixtures. This regeneration can be effected in-situ in the leach vessel or outside the leach vessel. An example of the application of this new process is presented for a Canadian sphalerite concentrate assaying 60% Zn. The effects of temperature, ferric concentration and ferric ion regeneration are presented. Options to recover zinc from the leach solution are also briefly discussed.

Jan 1, 2000

By Patrick R. Atkins

Energy issues will have increasing impacts on decision making in all facets of society over the next few decades. Industrial users of energy and producers of products that affect energy use must be fully aware of the implications of their processes and products on the energy situation. This paper describes a model that has been developed for the aluminum industry that allows scenarios to be evaluated to gain improved understanding of possible implications for our businesses. A brief overview of the model is provided.

Jan 1, 2006

By Freddy Syvertsen, Ali Riza Tarakcilar, Engin Tan, Derya Dispinar

"It has been shown that the disturbance of the advancing liquid front in the mould cavity may lead to surface entrained defects known as bifilms. These defects can deteriorate the mechanical properties significantly. The developments in the simulation of castings aid many casters. It is quick and economical. Therefore in this work, the aim was targeted to optimise the mould filling of a tensile test pattern design that is used for aluminium alloys. Several different designs, gatings and runner systems were investigated with Vulcan Casting Simulation Software. In addition to the achievement of non-turbulent and quiescent mould filling; other parameters such as temperature profile, porosity and feeding were investigated to optimise the process.IntroductionConsiderable effort has gone into understanding and controlling defects that are formed in aluminium and its alloys during casting. The conventional approach was the elimination of porosity by eliminating hydrogen in the melt simply due to the following reaction:"

Jan 1, 2012

By Patrick R. Atkins

Energy issues will have increasing impacts on decision making in all facets of society over the next few decades. Industrial users of energy and producers of products that affect energy use must be fully aware of the implications of their processes and products on the energy situation. This paper describes a model that has been developed for the aluminum industry that allows scenarios to be evaluated to gain improved understanding of possible implications for our businesses. A brief overview of the model is provided.

Jan 1, 2006

By M. L. Free

Electrowinning is directly impacted by many parameters that include electrolyte composition, voltage, current density, contact resistance, temperature, electrode spacing, and fluid flow as well as many other interrelated factors. The effects of these parameters are primarily related to thermodynamics, mass transport, and electrochemical kinetics. In this study thermodynamic, mass transport, and electrochemical kinetic equations are simultaneously solved to determine the effects of such parameters on electrowinning current efficiency, power consumption, electrodeposit morphology, and electrodeposit distribution. Modeling predictions will be compared with experimental results.

Jan 1, 2006

By J. C. Agarwal

Rare earth metal alloys are becoming increasingly important, particularly those of neodymium, because of their magnetic properties. This paper will present a generalized approach to the production economics of the metallic rare earth alloys. With appropriate regard for the chemistry of different rare earths and the large impact of economies of scale, it is possible to make fairly accurate estimates of the production costs of other rare earth alloys as well.

Jan 1, 1989

By J. Peter, S. E. James, J. L. Watson

A survey of operating zinc smelters and refineries throughout the world has been done in conjunction with the Lead-Zinc 2000 Symposium. This survey follows the examples set by the Japanese Mining Industry Association in 1985 and 1995. Questionnaires were sent to operating zinc plants that covered feed materials, process details, energy consumption and labor requirements. The voluntary responses to the survey were tabulated. Key operating parameters including feed grade, production capacity, quality of the intermediate products and quality of the final products have been compared for both hydrometallurgical and pyrometallurgical processes.

Jan 1, 2000

By O. C. Rojas

Improvements and modifications on lay out and process, from 1997 till 1998, are presented. Based on a Teniente Converter, started up 1993, a Strategic Development Plan was structured to increase the production efficiency and comply with the enviromental regulations, too. It considered the oxygen supplies to the Teniente Converter and Peirce Smith converters; reverberatory furnace shut down as a smelting unit; and the Teniente converter slag treatment through a combined process between a Slag Settler furnace and flotation. Also it included the off-gas handling and treatment.

Jan 1, 1999

By Daojin Cao

Aiming at many controversial reports on Raman spectral pattern of heptamolybdate ion in aqueous solution appearing in the literature and the absence of its standard pattern, the comparative investigations on Raman spectral pattern of saturated solution of ammonium heptamolybdate tetra hydrate were done. The results showed that the main vibrant frequencies of Raman spectral pattern of the saturated solution were in good agreement with those introduced in the literature, and that the intensity ratio (4.4) of the strongest peak to the second strongest peak recorded in Raman spectrum of the saturated solution had three obvious characteristics: it was greater than each of the results (ranging from 3.7 to 1.3) reported in the literature, much closer to that (4.7) of crystal and well conformed to the change rule of Raman spectra occurring in the process of the first-step polymerization of acidified molybdate solution. It was found that Raman spectrum of heptamolybdate ion in aqueous solution was determined by not only the main vibrant frequencies but also the intensity ratio, which is also the crucial result in this study. The comparative investigations indicate that the pattern of Raman spectrum of the saturated solution is the standard pattern of Raman spectrum of heptamolybdate ion in aqueous solution essentially. The affirmed standard pattern is reliable and can be used to the identification of heptamolybdate ion in aqueous solution, applied in the research of the equilibrium of acidified molybdate solution and the exploration of the best technologic condition for the production of high quality heptamolybdates.

Jan 1, 2006

By W. Marnette

Norddeutsche Affinerie is the largest West European copper producer with an annual output of more than 350,000 tonnes of refined copper, about half of which is produced from copper concentrates. However, in addition to concentrates, Norddeutsche Affinerie processes secondary raw materials and recycling materials which contain a combination of copper and lead. These materials were previously treated in blast furnaces, a technology which has meanwhile been superseded at NA by the electric furnace process, primarily owing to the necessity of complying with the increasingly stringent requirements for environmental protection.

Jan 1, 1994

By A. V. Tarasov

One or more of the main alloying metals, i.e. copper, silicon, nickel, magnesium, zinc and other metals can form a composition with aluminum, by dissolving in the latter. The thermodynamic computations have indicated that within a range of temperatures from 700°C to 1300°C the reactions of molten aluminum with zinc and nickel oxides are shifted toward formation of free metals because it is possible to use the main alloying metals, i.e. zinc and nickel, in the form of inexpensive intermediate products and waste. The laboratory studies conducted have confirmed a possibility for production of aluminum alloys using intermediate products in the form of oxides of alloying metals.

Jan 1, 2006

By Xu Zhong

The theoretical limit to smelting rate and possibly the size of a smelter is dependent on the rate of heat transfer, and the chemical kinetics of both sulfur removal and minor element volatilization. The fundamental kinetics of volatilization of minor elements such as As, Sb, Bi, and Pb from matte and white metal is being investigated. It has been shown that the molecular form of trace elements in matte depends on the chemical potential of sulfur and the propensity for the minor element to form a sulfide. The impact of the variable molecular form of the minor elements on the volatilization kinetics is unknown and is under investigation in this study. The experimental technique is reviewed and preliminary results are reported in this manuscript.

Jan 1, 1995

By K. Kashiwaya, N. Hiroyoshi, H. Furuya, N. Sumiya, M. Tsunekawa, M. Ito

"The number of hybrid vehicles is increasing and this is causeing an increase in waste nickelmetal hydride batteries. The cathode activating agent of batteries is made of nickel hydroxide and the anode activating agent is an alloy of nickel and rare earth elements. Conventional rotary kiln methods cannot recover the rare earth elements, and hydrometallurgical treatment of crushed product consumes large volumes of agent. The physical separation of the anode alloy from the cathode hydroxide would make it possible to reuse the alloy. The authors have reported separation of anode and cathode components in the large size fractions using a newly developed dry magnetic separation method. Wet magnetic separation has been applied to the powder fraction and about 90% anode purity was achieved. This paper reviews experimental results from previous publications and proposes an integrated treatment process for crushed nickel-metal hydride batteries.IntroductionEnvironmentally-conscious clean energy vehicles have attracted much attention in developed countries and particularly hybrid vehicles are increasingly mass-produced as low emission vehicles. Hybrid vehicles have both a gasoline engine and an electric motor to save on gasoline usage and a nickel-metal hydride battery is used to store electric energy. The battery contains Nihydroxide and Co as the cathode activating agent and an alloy of Ni and mischmetal (mM), a rare-earth element mixture consisting of La, Ce, and Nd, as the anode hydrogen adsorption component. In conventional recycling, the Ni and Fe are recovered with a rotary kiln-electric melting process and the Co and mM go to the slag component [1] and hydrometallurgical treatment of crushed product consumes large volumes of agent. Japan Oil, Gas and Metals National Corporation have proposed a low energy and low cost recycling treatment process combining the physical and chemical treatments and the authors are investigating the physical treatment process."

Jan 1, 2008

By Mikael Ersson

A fundamental mathematical model of lance blowing on a bath surface has been developed with a purpose to increase the understanding of various phenomena in top blown oxygen converters. The model is based on the Navier-Stokes equations and turbulence is predicted using the k-model. In the present model the deformation of the liquid surface, caused by the impinging gas jet, is described using a VOF formulation. The mathematical model results have been verified by comparing predicted penetration-depth data with experimental results from physical model trials. The fluid dynamic modeling has also been coupled with the thermodynamic modeling to predict the reaction rate/distribution occurring in the vessel. The focus has been on carbon and a qualitative comparison of the predicted carbon content in the hot spot area and in droplets with experimental data from laboratory trials has been done.

Jan 1, 2006

By Matti Hämäläinen

Outokumpu has developed a new chloride leaching process, HydroCopper?, for copper concentrates. The process utilizes the cupric ion as oxidant, which is able to dissolve chalcopyrite. After solution purification monovalent copper is precipitated as cuprous oxide, Cu2O, using sodium hydroxide. Copper product is produced from Cu2O by reduction, melting and casting. An essential part of the new process is chlor-alkali electrolysis, which regenerates the reagents used. All impurity metals are removed before Cu2O precipitation, because otherwise they would report to the copper product, impairing its quality. A multistage solution purification scheme has been developed consisting of firstly, chemical precipitation of impurity metals by pH increase, secondly, cementation of silver and thirdly, removal of trace multivalent ions using ion exchange. This paper describes the characteristics of solution purification in the HydroCopper? process based on the laboratory tests and pilot runs made by Outokumpu Research Oy.

Jan 1, 2003

By Aly M. Abdel-Rehim

The present work deals with a study of the mechanical activation of processing of Egyptian monazite by its simultaneous ball-milling and pressure leaching in order to improve the recovery of thorium and lanthanides from monazite. Experiments of simultaneous ball-milling and alkaline leaching of monazite contrary to autoclave leaching were carried out in stainless steel ball-mills of cylindrical shape under different conditions of temperature, pressure, time and alkali amount and strength. The ball-mills were heated and mechanically rotated in an electric furnace by means of roll mechanism. The effective rotation speed was fixed at 130 rpm in all tests. The charge of steel balls of different diameters was equivalent to 45% of the total mill volume. Monazite was charged in ball-mill without preliminary grinding. It is found that high rate of monazite leaching by ball-milling leaching method is achieved at lower temperature, shorter time and lower expense of alkali than in autoclaves. The results obtained show that complete recovery of thorium and lanthanides from monazite (99.8%) by simultaneous ball milling and alkaline leaching is attained at 140°C within 2 h. It is concluded that processing of monazite by its simultaneous ball-milling and leaching is mechanically activated and accelerated as a result of grinding action of steel balls that caused the continuous removal of the hydroxide product from reacting particle surfaces. This leads to the exposing of fresh and activated monazite particles surfaces to alkali leach solution and consequently the acceleration of the reaction of monazite processing.

Jan 1, 2006

By J. Brent Hiskey

Carefully prepared gold-bearing arsenopyrite samples from different geographical locations were leached in alkaline cyanide solutions using an electro-dissolution technique. Special precautions were taken to utilize monosized and thoroughly characterized samples. The rates of iron, arsenic, gold and silver dissolution were measured as a function of temperature under controlled conditions in sodium cyanide media.

Jan 1, 1989

By Chunlin Chen

Published data on thermodynamics of a number of minor elements (As, Sb, Bi, Pb, Zn, Se, Te, Cr, Sn) in liquid copper, matte and slag have been reviewed, assessed and used in development of thermodynamic solution models of melts. The behavior of antimony in alloys, mattes and slags is used as an example to illustrate the approach taken in assessment of published data and validation of the developed models with respect to the activity of Sb in condensed phases as well as the effects of matte grade, slag chemistry, temperature etc on the equilibrium distribution of Sb between melts and the gas phase. Results obtained from a comparison of different smelting processes with the modeled multi-phase equilibrium are presented and discussed. The predicted effects of slag chemistry and matte grade on the deportment of other minor elements during smelting of copper mattes will be presented and discussed.

Jan 1, 2006