Search Documents

By Moo Eob Choi

The reduction of iron oxide particles by hydrogen is one of the most widely investigated gas-solid reactions. The search for new methods for producing iron by the direct reduction of iron oxide has resulted in a large number of exhaustive studies of the various aspects of this reaction. However, previous studies have largely been done with either pellets or lump ores. Little has been published on the hydrogen reduction of very fine concentrate particles smaller than 37 µm (-400 mesh). The kinetics of hydrogen reduction of fine iron oxide concentrates were investigated in the temperature range of 900 - 1300°C.

Jan 1, 2006

By B. J. Beaudry

Intermetallic compounds are frequently required in the form of thin sheets for magnetic refrigeration and other applications. Progress has been made in the preparation of thin sheets of brittle gadolinium intermetallic compounds by hot rolling of sheathed billets. The effect of fabrication procedures on the Curie temperature of GdPd and its heat capacity at low temperatures has been studied.

Jan 1, 1989

By Kwang-suk You

This paper describes the characteristics of electric arc furnace slag (EAF slag) as an aggregate of concrete along with the chemical composition, leaching concentration of heavy metals, the soundness of EAF slag and compressive strength of mortar with 20% and 50% replacements of sand. The results showed that leaching of heavy metals and soundness of EAF slag satisfied Korean environmental limit and Korean Industrial Standard for aggregates. The compressive strength of mortar increased as the replacement ratio of EAF slag for sand increased.

Jan 1, 2006

By M. Hashiuchi

In 1972, the tankhouse of the Tamano Smelter adopted a high current density electrolysis operation applying the PRC (Periodic Reverse Current) method. In 1994, the phase four production expansion project, which incorporated significant re-structuring of the organization, was completed and we have achieved an annual production capacity of 191,000 tons. The target of this project, the production capacity, was increased by 1'8% and labor productivity by 25%. After the expansion, some improvements in the starting sheet section and the verticality of the electrodes were carried out, and the efficiency of the operation was greatly enhanced, including the improvement of the quality of the electrolytic copper.

Jan 1, 1999

By Jimsher Aneli

The investigation of some peculiarities of conductivity dependence on filler type and amount in the polymer composites has been conducted. It is established, that conductivity of composites based on phenolformaldehide resin essentially depends on proportion of double fillers: graphite + carbon black, graphite+ andesite, contained in composites. It was shown, that these composites characterized by synergetic effect ? non additive influence of fillers concentration on the conductivity of composites. Some other properties of composites contained binary fillers (effect of temperature and pressure on the conductivity) have been investigated.

Jan 1, 2006

By Natasa Mitevska

The distribution coefficients of Ag, As, Au, Bi, Co, Cu, Ni, Pb, Sb, Se, Te, and Zn between copper matte and slag from the reverb furnace No.2 at the Copper Smelter and Refinery, RTB BOR (Yugoslavia), are presented in this paper. The influence of the matte grade on the minor elements distribution coefficients between copper matte and slag is analyzed. The minor elements distribution in the slag phase along the slag melt depth and the furnace length is also determined.

Jan 1, 2002

By Peter J. Hancock

The pyrometallurgical .processing of non-ferrous, complex materials and wastes will be surveyed. Pyrometallurgy offers the most versatile way of processing a large variety of such materials because of its high temperatures, closely-controlled oxidation potential and the availability of commercially-proven reactor configurations. Some current industrial applications will be reviewed and possible new applications as well as future trends will be outlined.

Jan 1, 1994

By V. Ramachandran

ASARCO Incorporated, a large and diverse producer of non-ferrous metals, is involved primarily in smelting and refining of copper and lead. The Company also recovers by-product metals and chemicals produced in the smelting and refining process including selenium, tellurium, silver, gold, platinum, palladium, bismuth, antimony oxide, lead-antimony alloys, and nickel sulfate. The treatment of complex concentrates, containing high level's of impurities, also results in the production of various sludges, drosses, dusts and slags. This paper addresses the interplant and intraplant transfer of these materials between the copper and lead circuits and their subsequent treatment for maximum metals recovery. It also describes the role of ENCYCLB/TEXAS Inc., a subsidiary of Asarco, which treats Asarco's by-products, as well as hazardous and non-hazardous wastes produced by other manufacturers.

Jan 1, 1994

By G. J. Shiflet

This paper will review work done in our laboratory on the formation, thermodynamics and crystallization of aluminum based metallic glass with the addition of rare earth elements. The results demonstrate that the metallic glasses are truly amorphous and not microcrystalline and that they are unusual in their formation because the alloys contain 90 at. % aluminum and there is no deep eutectic present in the phase diagram. Tensile strengths that exceed 900 MPa are obtained for several of the compositions and exceed 1000 MPa after partial crystallization.

Jan 1, 1992

By M. A. Llavona

The study of the formation and components of copper patina and its conservation has assumed great importance. The changing environment has accelerated the processes of patinas degradation; thus, the exhaustive study of factors capable of affecting the patina formation, growth and durability has assumed great importance for the industrial activity of copper. The main components of the patina, oxides, chlorides, nitrates and sulfates, have been determined; the effect of physical, chemical and microbiological factors on patina formation, particularly the influence of acid rain, natural organic matter, particles and microorganisms have been defined. The effect of different electrolytic solutions that accelerate the formation of copper patinas has been determined, and a review of the state of knowledge of the formation and evolution of metal patinas has been made.

Jan 1, 1999

By K. L. Hardee

A recent development has emerged which produces a retrofittable, low cost anode by attaching disposable, electrocatalytically active titanium mesh over the existing lead anodes. The coated titanium mesh anode operates at potentials of several hundred millivolts lower than the lead anode, providing significant power savings. The exposed lead surfaces are stabilized since most of the current flows through the titanium mesh. With the minimal lead corrosion, the sludge formation is virtually eliminated and the purity of the plated copper is greatly enhanced. Further savings may be realized by the elimination of non-essential chemicals such as cobalt. Since the combination anode is stable and uniform, the plated copper is also more uniform with minimal formation of dendrites, reducing the shorting. Full-size anodes have been tested for over 6 months in commercial copper electrowinning cells. The laboratory and field performance of the stabilized lead anode will be reviewed, including the voltage characteristics, the lead stability and the copper cathode purity.

Jan 1, 1999

By Todd S. Fayram

The Gordonsville Operation of Pasminco US Inc. along with the Center for Advanced Mineral and Metallurgical Processing (CAMP) at Montana Tech studied, developed and implemented a pilot scale hydrometallurgical facility for the industrial recovery of germanium and gallium. This paper describes the joint testing and engineering program that culminated in this successful process.

Jan 1, 2003

By K. Osseo-Asare

Aqueous stability diagrams (25°C) are presented for the systems M-H2O and M-Oxalate-H2O where M=Sm, Nd, Co, and Fe. With the aid of these diagrams (i.e., Eh-pH and log[Metal]- log[Oxalate]), the solution-chemical constraints on metal dissolution and precipitation are identified. By comparing the corresponding stability diagrams, conceptual flowsheets are developed for metal recovery from Sm-Co and Nd-Fe-B magnet scrap.

Jan 1, 1997

By KNona C. Liddell

The time and spatial dependence of component and species concentrations during in situ uraninite leaching have been modeled using a reactive transport model based on partial equilibrium between reactive minerals and the solution. The flow field is represented by mixing cells in series. The effects of the H2O2, (NH4)2CO3, and NH4HCO3 component concentrations have been simulated, and results are presented for a one-dimensional flow field.

Jan 1, 1995

By Y. Mori, K. Kawanaka

The permeability changes during the sintering of the feed for the Imperial Smelting Process (ISP) were investigated using an experimental sintering pot, as well as with a mathematical model. The results obtained were as follows. The blowing resistance in the sintering bed changes as the sintering reaction proceeds. It increases at the beginning of the reaction when the temperature of the bed is still low. Then it decreases as the reaction continues, accompanied by an increase of the bed temperature. The increase of the blowing resistance in the bed during the sintering process mainly occurred in the drying zone, and was comparatively small in the reaction and cooling zones. Based on Erugen's equation, the change of the permeability during sintering is explained by the decrease of the apparent fractional void volume in the drying zone of the bed.

Jan 1, 2000

By Jin-Chun Kim

Nanosized W based powders (W, WC, WC-Co) were produced by chemical vapor condensation (CVC) process. Two different solid W(CO)6 and Co2(CO)8 metal-organic materials were used as precursors. CVC experiment was conducted in the temperature range of 400-1100. As-CVC WC1-x powder which had non-stoichiometric composition was carburized by using of the CH4-H2 mixed gas in temperature range of 750-850. The CVC W and WC1-x powders showed loosely agglomeration structure, and the Co powder had intricate long stand structure because of intrinsic magnetic properties of Co phase. Carbon content of the CVC powders controlled by gas-phase carburization was well matched with theoretical WC stoichiometry (6.13wt%).

Jan 1, 2006

By Wenshan Zhang

This paper described the present status of China electrolytic manganese industrial production. Electrochemical reactions on cathode and anode, the major technological process, technical requirements on the production and technical index and quality control of the products and the ways of increasing current efficiency during Manganese electrolytic process have been expatiated.

Jan 1, 2006

By José C. Escobedo B.

A kinetic study of nitrogen dissolution in a. electromagnetically stirred Co-Cr-Mo alloy bath was made. The experiments were carried out at 1693, 1723 and 1743K of temperature, with a nitrogen pressure of 0.67 atm. The mass transfer coefficients were obtained, finding that their values increase as temperature grows. The true kinetic constants were calculated. It was found that at 1693K of temperature, the kinetics of the nitrogen dissolution process is controlled by a mixed mechanism involving both transport processes and chemical reaction, while at 1723 and 1743K of temperature, the kinetics is controlled only by transport processes mechanisms.

Jan 1, 1995

By Christian Hecker

An Eh-pH electrochemical sensor developed for on-line pH and redox potentials copper sulphide flotation process control was studied. The electrochemical sensor cell includes two metallic platinum electrodes, a metallic antimony electrode and a high impedance reference cell which are polarized with a potentiostat. For pH and redox potential determinations, the Sb and platinum electrode potentials are measured, respectively, against the polarized electrochemical reference system. The behaviour of this electrode configuration has been investigated in a laboratory scale. An electrochemical sensor device has been succesfully installed and checked in El Teninte Colon Concentrator's SAG line feeding the copper flotation rougher circuit.

Jan 1, 1999

By Vladyslav M. Sokolov

The cost effective and environmentally friendly recycling technology was developed and tested. It enables utilization of the fine nickel-base superalloy scrap in a form of heavily oxidized scarfing granulates. The process of granulates generation was discussed in details. Their properties were investigated. The results of literature search showed anticipated sufficient improvement of the properties of cast iron by its alloying with the elements from the scarfing granulates. The novel alloying approach is based on the two stage reduction operation. Firstly thegranulates were partially reduced in a solid state by their exposure with powdery carbon at the range of 1550 ? 1700°C. Then the gotten product was efficiently introduced into liquid iron since it has a form of fine natural agglomerates for arranging the optimal conditions for reduction of the granulates. The thermodynamic evaluation demonstrates higher reduction efficiency of carbon and silicon dissolved in iron than of the same elements in a form of the separate phases. The considered process partially provides itself by energy since the reaction of reduction of the chromium oxide by silicon dissolved in liquid iron has exothermal character. The mostly complete extraction of Ni was received. The sufficient reclamation of Cr was gotten at the same time.

Jan 1, 2006