Search Documents

By G. G. Krishna Murthy

Several experiments were carried out to simulate the bath smelting reactions where iron oxide particles were dropped on to an iron-carbon bath containing molten CaO-SiO2-Al2O3 slag layer on its surface. The composition of the slags used in the experiments was %CaO:46.1; %SiO2:41.7; and %A1203:12.2. Experiments were con¬ducted with carbon saturated iron melts contained in either a pure graphite crucible whose walls were covered with a pure alumina tube, or a pure flat bottom alumina crucible, at 1723-1823 K. Degree of reduction of a pure iron oxide particle was linear with time in the initial stages (up to about 20% oxygen of the original pellet was reduced). The rate of reduction of smaller oxide pellets was smaller than that of a bigger pellet - the time for complete reduction of a 5.6 g wustite pellet was smaller than that for a 1.2 g wustite pellet. It was also established that the interaction rates obtained by adding a molten pure oxide particle of given weight to the system were lower than that determined by using a solid oxide particle of same weight. The overall rates of reduction decreased with decreasing the bath temperature. The experimentally determined rates of reduction based on the time for 70% reduction were influenced substantially by addition of slag up to about 50 g on to a bath of 78.8 mm in diameter, and remained constant when slag present on the bath surface was between 50 g and 200 g.

Jan 1, 1993

By Marcelo B. Mourao

Interactions of carbonaceous materials with liquid Fe-C melts have been investigated experimentally by determining the volatile yield due to rapid devolatilization (Flash Pyrolysis) and rates of dissolution at temperatures ranging from 1623 to 1873 K. The volatile yield increased with increasing the temperature. The comparison of results of different types of carbonaceous materials was possible by expressing the volatile yield in terms of Enhancement Factor, fE. The rates of dissolution of spectroscopic graphite and an industrial coke seemed to obey the correlation for natural convection under turbulent conditions. The experimental data for the graphite suggested that the rate of dissolution was controlled by the mass-transfer in the liquid boundary layer adjacent to the solid sample. The value for the empirical parameter correlating the dissolution coefficient and the operating variables was found to be 0.19 which was close to that reported in the literature. The comparison of the results obtained for the coke samples with those for the graphite revealed that the impurities and the porosity of the samples can effect the dissolution rates.

Jan 1, 1992

By Ana E. Bohé, Fabiola J. Alvarez

"The separation of nickel from the aluminum present in spent catalysts and different metallic industrial residues, is proposed in the following systems: alloy Al2Ni and the mixtures 50 wt% Ni + 50 wt% Al, 10 wt% Ni + 90 wt% Al2O3 and 12 wt% NiO + 88 wt% Al2O3. The experiments were carried out in a tubular reactor with a flow of 2 l/h of gaseous chlorine and from 200 ° to 800 °C. The final products of the reaction, extracted from the hottest zones of the reactor where characterized by XRD, SEM, EDS, AA and XRF, as NiCl2 y NiCl2.6H2O while in the coldest regions AlCl3 was deposited in the first two cases and in the other there was a residue of ?, a- Al2O3, sometimes mixed with some remainder of Ni and NiO. The procedure attained different separation factors which showed the optimun conditions for the recovery of both metals. Introduction Some studies of nickel corrosion were carried out in chlorine gas at temperatures above 950ºC, and suggested that nickel is not corroded below 538ºC. [1] However, in a previous work it was shown that the chlorination allows the separation of nickel from aluminum and the formation of NiCl2 was detected from 200ºC in binary mixtures Ni-Al 50 wt%, for isothermal conditions in chlorine flux. [2] Other researchers obtained selective chlorination above 650ºC of a fly ash containing 1.4 wt% of Ni and other metals (V, Mg, Al and Fe). The Ni was separated from the Mg and NiCl2 started to vaporize at 550ºC and was after condensed in a zone of the reactor above 380ºC with 90% of purity. [3]"

Jan 1, 2008

By A. A. EI-Geassy

High-grade iron ore fines rejected from the DRI plants (>96%Fe2O3) were isothermally reduced in 30-60%CO/H2 gas mixtures at 973-1273K. The freshly reduced reaction products were then subsequently carburised in either Hz/CO or H2/CO/S mixtures at 823-1 073K for 30-120 min. The thermogarvimetric technique was used to follow up both of reduction and carburisation reactions as a function of time. The carburised samples were characterized by X-ray and Mossbauer techniques. Chemical and carbon analyses were also applied. The influence of temperature and gas composition on the reduction behavior was investigated. The calculated values of apparent activation energy, application of gas-solid mathematical formulations were correlated with the microstructures to predict the reduetion mechanism. The influenee of carburization time, temperature, CO contents in H2/CO or H2/CO/S were investigated. A conversion extent of Fe to Fe3C was taken as a measurable index for the efficiency of carburization rcaction under the different experimental conditions.

Jan 1, 2003

By C. P. Broadbent

The process metallurgy of many nickel laterite smelting operations is controlled largely by the physical chemistry of the slag system. Consequently, accurate phase diagram information and physicochemical property data are essential to interpret and predict the behaviour and optimisation of the overall process. The system (SiO2 - MgO - FeO) first described by Bowen et al. between 1914 and 1935 and the system (SiO2 - MgO - FeO - Fe2O3) determined by Muan and Osborne in 1956 are of particular relevance to the study of nickel laterite smelting slags as these systems form a reasonable approximation of many industrial slags. This paper will review the literature for these (and other relevant) phase systems. In addition data available from the ternary and (quasi)ternary phase diagrams will be compared with data obtained from industrial slags. The physico-chemical properties under consideration will include; melting and crystallisation behaviour (solidus and liquidus temperatures), viscosity - temperature relationships, heat flux considerations, electrical conductivity, surface and interfacial tension.

Jan 1, 1993

By Shadia J. Ikhmayies

"Tin oxide (SnU2) thin films of thicknesses in the range 100-600 nm were prepared on glass substrates by vacuum evaporation at ambient temperature. The films were characterized by transmittance measurements, X-ray diffraction (XRD), scanning electron microscope (SEM) observations and energy dispersion X-ray analysis (EDAX). It is found that the films have high transmittance and non sharp absorption edges. XRD diffractograms showed that the films are amorphous and the SEM micrographs showed that the surfaces are smooth, uniform and well covered with the material. The EDAX analysis showed that the films are deficient in oxygen. Indirect optical bandgap energy and Urbach tailing in the bandgap was observed, and the width of the tail, which is related with disorder and localized states, was estimated.IntroductionTin oxide is an n-type wide bandgap semiconducting material with a direct bandgap energy of 4 eV and an indirect bandgap of 2.6 eV [1], where inherent oxygen vacancies act as an n-type dopant [2], Tin oxide thin films have been used for transparent electrodes in photoelectric conversion devices namely amorphous silicon solar cells, liquid crystal displays, gas discharge displays, etc. [3]. Perfectly amorphous thin SnO2 films show good electrical response to reducing gases in air and could, hence, be applied to construct semiconductor gas sensors where the metal oxide films function as a monograin-eqivalent active layer [4]. Amorphous SnU2 can also be used in extended gate field-effect transistors (EGFET) as a pH sensor, where the sensitive part is made of the SnO2/Al structure. This device can be used to detect and to quantify any kind of substance that can produce or consume protons, like an enzymatic reaction, therefore showing a large range of applications as biosensors [5].There are different methods to prepare SnO2 films, such as atomic layer deposition (ALD) [6], reactive magnetron sputtering [7], chemical vapor deposition [8, 9], dip coating [10], spray pyrolysis (SP) [3, 11-14], and evaporation [8], The thermal evaporation method was chosen to produce SnO2 thin films in this work because deposition by this technique does not present any compositional problems. In addition, it is a low temperature technique, which increases the probability of producing amorphous films. To increase this probability, the films were deposited at ambient temperature."

Jan 1, 2012

By J. Szekely, S. Rhee

"A mathematical formulation has been presented to describe heat and fluid flow phenomena in CVD operations. In the statement of the problem, which included consideration of plasma enhanced CVD systems, emphasis was placed on identifying the parameters which play a key role in determining the rate and the spatial uniformity of the deposition process. This was done both through the appropriate dimensionless groups and by presenting an extensive set of computed results. The main conclusions that may be drawn from this work are that the deposition rate will be inherently non-uniform for atmospheric CVD systems; this may be somewhat ameliorated by inclining the susceptor or changing the vessel contours. Operation at greatly redeced pressures and for PECVD systems will give a much more spatially uniform deposition rate.1. INTRODUCTIONIn recent years, there has been a growing interest in chemical vapor deposition techniques for the preparation of thin films for semiconductor, photovoltaic applications and for coatings in general, as evidenced by numerous journal articles and symposium proceedings devoted to this topic (1-6). An interesting variant of this technique is to perform the deposition in a plasma or glow discharge at low pressures because this technology obviates the need for the thermal decomposition of the precursor at the substrate surface and permits operation at greatly reduced temperatures (7-10).By far, the largest portion of the reported work dealing with both these aspects of the technology has been concerned with the characterization of the deposit, quite properly so. However, in more recent times it has been realized that the transport aspects of these processes are also deserving of attention because the understanding of heat flow, fluid flow and diffusional phenomena may provide the key to the solution of problems associated with obtaining uniform deposits and the proper scaling of laboratory measurements in order to design industrial CVD systems."

Jan 1, 1986

By Mark Osborne, Ray D. Peterson, C. Edward Eckert

"The theoretical melting energy requirement for a typical hypoeutectic aluminum-silicon alloy is approximately 520 BTU/lb. It has been demonstrated, however, that even a state of the art secondary processing-automated lost foam casting operation can exceed this value by at least an order of magnitude when the actual thermal energy input from melting to solidification is monitored. Metal transfer and holding operations constitutes over 65% of this expenditure. The authors present relative benchmark energy expenditure information by unit operation for an offsite melting/lost foam casting line with a daily throughput in excess of 100,000 lbs. Efficiency improvements through optimization of the current process, and anticipated energy values at the culmination of a U.S. Department of Energy sponsored project to develop, integrate and demonstrate an advanced melting, transportation, and dispensation system will be cited.IntroductionThe size of the U.S. aluminum remelt pool was approximated to be 14.21 billion kg (31.27 billion pounds) by a recent study?, with the engineered castings (foundry) sector accounting for 3.25 billion kg (7.16 billion pounds) or 23% of that total. This study considered overall process yield and all major contributors to scrap. The values cited, therefore, are more meaningful than simply tabulating annual pounds shipped by sector.The foundry sector consists of Sand Castings, PM Castings and Die Castings categories appearing in Figure 1. All other categories comprise the wrought alloy sector. Wrought alloy production enjoys an energetic benefit from both scale and a relatively continuous operation. Many foundry operations, however, operate in batch mode at less than design metal throughput with characteristically longer melt holding periods. Since any detention of molten metal beyond melting represents an overhead use of energy, melt holding (secondary) energy expenditures can appreciably inflate melting energy requirements in the foundry."

Jan 1, 2009

Based on experimental and computer simulation results from our group, we report a systematic, atomic level analysis of carbon dissolution from carbonaceous materials in molten iron. Experimental results on graphite/Fe-C-S system were obtained using carbon dissolution studies, XRD and FESEM investigations and were supplemented with Monte Carlo simulations. Three basic mechanisms, namely carbon atom dissociation rate, interfacial phenomena and mass transfer in the melt were found to be responsible for the overall dissolution process. While mass transfer in the melt is governed by the concentration gradients, melt composition and temperature; impurities present in ash play a significant role in the interfacial phenomena. For less ordered forms of carbonaceous materials, carbon atom dissociation rate depends strongly on the degree of long-range order and is an important rate controlling mechanism in the overall dissolution process. A systematic comparison of dissolution rates for a variety of coal-chars, natural and synthetic graphites has been carried out in an attempt to identify rate-controlling mechanisms. The structure of the carbonaceous material appears to be an important underlying factor in the carbon dissolution process.

Jan 1, 2003

By Marion Dattilo

The search for an improved anode for the electrowinning of lead from fluosi1icic acid medium has led the U.S. Bureau of Mines to investigate composites. Polymer bonded metal oxide powders which may contain catalyst additions were prepared by pressing. These composites display an improved activity toward the oxygen evolution reaction over electrodeposited lead dioxide on titanium, carbon, and nickel substrates. These composite electrodes contain 5 to 10 wt. " binding polymer, with the balance being metal oxides. Lowered anodic potentials achieved using the compnsite anodes resulted in lower levels of lead dioxide deposition during electrowinning.

Jan 1, 1995

By D. Papazoglou

This work was undertaken to investigate the thermodynamic and kinetic feasibility of using hot sulfur dioxide bearing gases from smelting processes to selectively sulfate the nickel in nickel laterite ores for subsequent extraction in water. The environmental benefits of this approach, as opposed to releasing the gas to the atmosphere, and the economic benefit of directly utilizing the SO2 rather than converting it to sulfuric acid are strong drivers for such a process. A thermodynamic analysis indicated that selective sulfation of the nickel could be feasible under appropriate conditions and these were explored through a series of laboratory scale experiments. Laterite samples were reacted at temperatures between 500 and 800°C with an equilibrated mixture of sulfur dioxide, oxygen and nitrogen in a fixed bed reactor. Tests were conducted on saprolitic ore from Bulong, Western Australia:, limonitic ore from New Caledonia and gamieritic ore from Indonesia. Nickel extractions were highest from the limonite and relatively low from the other ores. The maximum selective extraction of nickel from the limonite in a single stage sulfation was 73%. Sulfation of other elements present in the laterites was also examined. A two-stage process was also identified which involved sulfation using a strong sulfation potenrial followed by weaker sulfation potential to attempt to convert ferric sulfate formed in the first stage to ferric oxide. This increased the extraction for the limonite ore to around 84% Ni, 95% Co and 2% Fe. Direct sulfation of laterite could be feasible in locations where sulfide smelting or roasting operations are relatively close to laterite deposits.

Jan 1, 2003

By Xia Lou, Hossein Dashti

Gas hydrates technology has been considered as an alternative method for carbon dioxide (CO2) separation. A wide range of studies have been reported in the past decade on the improvement of the separation efficiency by using chemical additives. While most of these studies have shown improved kinetics, thermodynamics and/or separation efficiency at the laboratory scale, there has been no quantitative analysis of the energy consumption for viable industrial applications. Comparison of the effectiveness of the chemical additives from separate studies or groups also is impossible. The present work is focused on the modelling of the hydrate-based CO2 separation process and provides a quantitative approach that is new in its analysis of the effectiveness of chemical additives in relation to the energy required and the kinetic parameters involved in the process.

Mar 1, 2018

By Vasil Kopaleishvili

The bainitic Fe-C-Si alloys with optimum content of retained austenite serve as ?containers? for storing of hydrogen. Both the vacancies of fcc lattice and the possibility of forming hydrides of silicon and other alloying elements will be used. The idea is based on our scientific hypothesis. There is the silicon threshold (Si=0,50%) in "Fe-Si" system and Fe-C bainitic alloys, above which it causes self-organized phenomena: sudden increase of hydrogen solubility and amount of retained austenite in the alloy after ??ß transformation, formation of two supersaturated solid solutions <a??r>, "rejuvenation? and its reverse process. Rapprochement of iron atoms when Si=0,50%, causes appearance of new covalent forces where uncompensated electrons of 3d-subshell are involved and it provokes synergetic phenomena. They ?free? silicon atoms from the previous bonds. After that silicon itself becomes a getter of hydrogen using vacancies (14) of 3P2(6)d0(10) subshell and it results in sudden increase of hydrogen solubility in metal. Simultaneously sudden decrease of iron activity takes place. That in its turn ?releases? the carbon. Thus, its redistribution, controlling the bainitic transformation, is hastened. It stipulates for creation of ?brittle bainite" B[a(C,H)+?r(C,H)] after ??ß transformation. While weathering of metal, "rejuvenating", hydrogen diffuses in ?islets? of retained austenite and ?relaxed bainite? (B[(C)+?r(C,H+H)]) is obtained. When heating austenite ?(C,H) is obtained, and after cooling ?brittle bainite? is obtained, etc. Presented scientific hypothesis explains the available experimental facts ("rejuvenation? and its reverse process, graphitization, weldability, forming of flakes, reaching high strength, etc.) in a new manner, as well as, gives real opportunity for creating of new trends in many fields, e.g. iron based HAA. Provisional data having been obtained are encouraging.

Jan 1, 2006

By Jay S. Gunasekera

Since great emphasis is being placed on the manufacturing science and processing science programs in the Department of Defence and other government research agencies and industries; currently, extensive research on computer aided design(CAD)/ computer aided manufacturing (CAM)/ and computer aided engineering (CAE) is being conducted at Ohio University (OU) . OU has invested over a million dollars in CAD/CAM hardware and software. Design and analysis packages like ALPID, NIKE, STREAM, SHEAR, POLY_FLON, RINGROLL have been developed or modified at OUusing finite element method, finite difference techniques or enhanced slab analysis. Packages like ABAQUS, FLUENT, and NASTRAN have been extensively used.

Jan 1, 1990

By Robert P. Stevens

It is important for a refractory supplier to make systematic petro-graphic examinations of products which have been in service in the furnaces and kilns of customers. The petrographic examination of refractory service samples involves the microscopic study of polished and/or thin sections, supplemented by electron probe microanalysis, as well as the bulk chemical and XRD analysis of zones in the samples. The evolution of the A. P. Green Refractories Company petrographic laboratory is described, and the application of petrographic methods is illustrated in the examination of service refractories from a Portland cement rotary kiln and an AOD stainless steel vessel. The objectives of such studies are to assist the customer in the solution of his refractory problems, and to accumulate data which are of use in the design of improved refractory products.

Jan 1, 1981

By G. C. Yao

Branch and needle-shaped intermctallic compounds of iron, silicon and aluminum normally exist in the molten aluminum. If a suitable amount of manganese metal is added into molten aluminum, the shape of the intermallie compound particlcs may become lumpish and spherical. According to the difference in electric and magnetic properties of these impurity particles and molten aluminum, these impurity intermctallie compound particles can be separated by applying an alternating magnetic field. In this experiment the alternating magnetic field was formed by a "C" type loop with AC (50Hz) current. The inner vacuum of the fireclay refractory separator is 25>< 15" 130mm3 with a lateral baffle inside. The separator was put into the interspace of the "C" type loop. It was found that the longer the separation time, the larger the amount transferred of impurities. The amount of transferred impurities increases with the increase of separation time and intensity of magnetic field. The addition of manganese metal enhanees signifieantly the efficiency of impurity separation.

Jan 1, 2003

By G. C. Yao

Iron and silicon impurities can form needle and branch shape intermetallie compounds in molten aluminum when there is no manganese. It is difficult to separate them from molten aluminum by electromagnetic separation. The Fe-Si-AI and Fe-AI intcrmetallic compounds were transformed into Mn-Fe-Si-AI and Mn-Fe-AI compounds by the addition of manganesc into molten aluminum, In molten aluminum the morphology of these intermetallic compound particles is lumpish and spherical. Migration resistance of these impurity particles is small, which is beneficial to separation. FeSiMnAl4 and FeMnAl6 arc paramagnetic. These impurity particles can be moved by magnetic force and can be separated from the molten aluminum.

Jan 1, 2003

By Onuralp Yiicel, Ozlem Okur, Murat Alkan

"In this study, Co-Cr-Mo alloys were produced using a mixture of Co304, Cr203 and Mo03 powders with Al powders by a Self-propagating high temperature synthesis process. SHS is a process of material synthesis that has revealed a number of reactants combinations capable of much higher energy release than conventional explosives. Al203 is added to the mixture to decrease the adiabatic temperature of the system. The thermodynamic simulations and the calculations of adiabatic temperature were examined with FactSage 6.2. In the SHS experiments, different Co304/ Cr203/Mo03 ratios were examined, and their effects on the metal recovery and alloy compositions were carried out. The samples were characterized by using chemical analysis, XRD, XRF and SEM/EDS techniques.IntroductionSelf Propagating High Temperature Synthesis (SHS) has significant advantages compared to the high technology furnace applications, such as very short processing time, simple operation, low energy requirement and low cost [l, 2]. In a SHS process, the ignition starts the combustion and propagates throughout the reactant mixture yielding the desired product. However, the disadvantages of the process such as inhomogeneous or unreacted products due to undesirable reaction rates needs to be overcome by changing some parameters such as ignition temperature, particle size, additive, atmosphere etc. [3, 4]. This work aims to establish a scientific and engineering background in the production of some cast Co-Cr-Mo master alloys via SHS (Self Propagating High Temperature Synthesis) metallurgy which is attractive process technique regarding fast and low-cost production ability of cast alloys."

Jan 1, 2013

By Wenjun Duan, Zongliang Zuo, Qingbo Yu, Qin Qin, Junxiang Liu

Moving bed has been widely used in the field of heat and mass transfer and reaction between solid particles and gas. In order to enhance the heat exchange coefficient, there will be tube banks inserted in the moving bed. In the process of drying ammoniates particles or heat recovery from high-temperature particles with moving bed, the particles flow behavior around the tube banks is significant. In this paper, the particles flow behavior around the tube banks is investigated, and all the results can provide guidance for the design and operation of a moving bed.

Jan 1, 2016

By José R. de Tenorio

The aim of the present work was to investigate the reduction process of MnO~FeO-Si02 slags by carbon-saturated liquid iron. The effect of the initial Mn content in the bath was explored. The initial Mn content was in the range of 0 up to 40 wt. %. The MnO content in the slag was kept constant at 40 wt. %. Tests were performed in laboratory apparatus. Samples of slags and bath were taken. In the first 5 minutes, it was observed a very strong reduction of FeO. This first step promoted a MnO-Si02 enrichment of the slag and a formation of CO bubbles, which increases the slag level. The increase ofMn content decreases the MnO reduction rate.

Jan 1, 1996