Search Documents

By E. A. Werner, A. Pichler, A. Spalek, G. Reisner, P. Stiaszny

"Interstitial free (IF) sheet steels are used for complex shaped parts because of their excellent formability. If a deep drawn part is subjected· to a impact deformation at low temperature brittle fracture of the part may occur. This phenomenon\ is called secondary work embrittlement (SWE). One possibility to characterize this material/structural behavior is the drop-weight test. The result of .this .test is a temperature at and below which a crack can initiated in a deep drawn part under the investigated set of parameters. This paper addresses the influence of the preforming process on the sus- . . ceptibili.ty of IF steels to SWE.IntroductionInterstiiial:free (IF-) steels are frequently used in the automotive industry for complex· shaped p·arts because of their excellent deep drawability. The microstructure of the steel consists of a highly ductile ferritic matrix with embedded precipitates of nitrides and/or carbides. Brittle fracture can occur in deep drawn parts, if they are subjected to a high speed deformation at lo""w temperature. This phenomenon is called ~econdary Work gmbrittlement (SWE) [1-11]. Up to now there are no standardized testing procedures available to quantify the sensibility of IF-sheet steel to SWE. Neveitheless, a reasonable testing procedure which allows to quantify the tendency of a predeformed part to SWE is necessary for further material development. A commonly used test method is the drop-weight test performed at low temperatures. In such ·tests a cone-like drop weight expands a deep drawn cylindrical cup [l-3, 6, 8, 9, 11]. From this expansion experiment the temperature is determined at and below which a brittle crack can be initiated in the deep drawn cup under the investigated impact test parameters. The highest measured temperature at which a deep drawn cup fails by brittle fracture is called frack appearances !emperature (CAPT). The lower the value of the CAPT the lower is the sensibility of a deep drawn part of IF-sheet steel to SWE. This paper aims to clarify the role of the preforming process on the impact behavior of an IF steel. For this purpose a numerical analysis of the deep drawing process and cup expansion tests are conducted."

Jan 1, 2000

By Yang Wang, Xiancong Zhao, Hao Bai, Qi Shi, Zhancheng Guo

Linz-Donawitz converter gas (LDG) or basic oxygen steelmaking gas (BOSG) is one of the most important secondary energy sources in iron and steel industry, whose effective use plays a vital role in energy saving and emission reduction. However, the generation of LDG suffers from great fluctuation with respect to the production status of steel making. Therefore, a long term prediction model of LDG generation would be essential in gas system balancing and optimization. In this paper, a long term prediction model for the generation volume of LDG was proposed based on the steelmaking production estimation from Gantt chart and k-means clustering algorithm. Compared with the previous model, this model considered the influence of different steel type on LDG generation. The experimental results of a steel plant demonstrate that the proposed model exhibits high accuracy and can provide an effective guidance for balancing and scheduling of byproduct gases.

Jan 1, 2016

By Takahiro Miki

Soldering material widely used is Sn-Pb alloy, which have low melting point and excellent electrical, strength properties and wettability. However, Pb is one of the toxic elements, which is undesirable due to environmental and safety reasons, thus Pb-free alternative alloy is preferred for new soldering material. Sn-Ag and Sn-Zn based alloys have been viewed as very promising candidates, among many potential substitutes. Addition of third element to these alloys will decrease melting point of the alloys. Hence, Sn-Ag-In and Sn-Zn-Mg alloys are expected to be suitable for replacing Sn-Pb solder alloy. In order to design new Pb-free soldering materials, it is crucial to understand precise thermodynamic properties and phase diagrams of alloy systems. In the present work, ion current ratios of Ag to In and Mg to Zn were measured for Sn-Ag-In and Sn-Zn-Mg alloys by mass spectrometry, respectively. Also, the authors reviewed the thermodynamic properties of terminal binary alloys determined by other researchers and evaluated a thermodynamic functions to express the excess Gibbs free energy of each binary alloy. Thermodynamic functions to express the excess Gibbs free energy of liquid Sn-Ag-In and Sn-Zn-Mg ternary alloys were determined, utilizing the assessed Gibbs free energy of terminal binary alloys with the measured ion current ratios using mass spectrometer.

Jan 1, 2003

By James T. Staley

Quenching and aging are critical processing steps used to produce precipitation hardenable aluminum alloy products. This work describes personal computer programs that employ models to predict certain properties after quenching and aging and graphically display them. One of the programs allows the user to predict the attainable strength and toughness of aluminum alloy products after an arbitrary quench. Another program simulates the changes in strength and electrical conductivity occurring during second-step aging alloy 7050-T7X products as a function of thickness, furnace temperature set point, and furnace characteristics.

Jan 1, 1993

By Sergey Komarov, Manuela Diaz, Sano. Masamichi

"Mixing time, bubble behavior and absorption rate of gas injected into a liquid bath through rotary L-shaped lances have been studied by cold models with an effort to improve refining characteristics of metallurgical processes. Two kinds of the rotary lances were tested, namely the single-hole lance and the multi-hole lance. The effects of gas flow rate, bath depth and rotation speed were examined.It is found that when gas is injected through the rotary lances, the mixing intensity and the gas absorption rate are larger than that for the gas injection through stationary lances. The effect of rotation speed decreases as the bath depth and the gas flow rate increase.The multi-hole lance produces much smaller bubbles, which lead to an increase in the volumetric mass transfer coefficient by 3-4 times as compared with the single-hole lance. However, the effect of rotation speed is smaller for the multi-hole lance. The obtained results are explained in terms of the bubble coalescence and fragmentation, the rate of which depends on the departure bubble size and the power supplied to the liquid bath.IntroductionIn recent years, there has been a growing interest in the development of gas injector for metallurgical processes. The majority of the previous work was focused on modification to the injector design to improve mixing and to increase the of chemical reaction rate. These two goals can not be necessarily achieved by the same way. Bottom nozzles and stationary immersed top lances, which have been widely applied to steelmaking processes, are effective for the bath mixing, but have a limit to decrease in the bubble size. This results from a vigorous coalescence occurring between the bubbles when they rise in the molten bath as a bubble swarm.One of the ways to ensure the small bubble size and the effective bath stirring is the gas purging through rotary injectors. A number of studies have been undertaken to improve the refining characteristics by using rotary injectors. All of them are related to aluminum refining. The SNIF equipment (The Spinning Nozzle Inert Flotation) has significantly improved the quality of aluminum products at National Luxemburg Aluminum [1]. Rotary injectors made in the form of a disc have been applied to the Alcoa 622 [2] and the GBF processes [3]. A study of the gas injection by a rotary impeller has been carried out by C. Leroy and G. Pignacelt [4]. All researchers note the significant improvement in removal of sodium, calcium, hydrogen and non-metallic inclusion."

Jan 1, 1996

By Petre Stelian Nita

In small steelmaking shops, in foundries and forging plants, there are not too many option to recycle the basic slags, which are not suitable for many purposes of recycling, because of their low chemical and structural stability. A solution of an adequate recycling is a direct recycling in EAF. Several quality requirements, physico-chemical properties and proportions of slags must be analysed. The progress in this fields permites to establish an adequate proportion of recycled slag, based on enough exact computation of the related property. For oxydizing slag, obtained during melting and in the first part of decarburization operation, the problem of phosphoms contents can be analysed using the phosphate capacity (C PO34-). For reducing periods, during deoxidization operation, desulphurization also occurs and the problem of the sulphur contents can be analysed using the sulphur and sulphide capacities ( Cs / Cs) Between this two complex thermodynamic indicators of the slags. a direct relation is established, using thermodynamic aspects, resulting from the equilibrium constants for dephosphorization and desulphurization process and also, using the optical basicity of slags, computable from the chemical analysis of the slags. On this basis starting from the steel quality requirements. adequate strategies can be established in order to obtain high rates of recycling (between 50-80%) of steelmaking slags. Important cost savings are obtained through this procedure, based on the correct amounts of the fresh lime, iron ore and fluidizers. Keywords: Slag, Properties, Recycling

Jan 1, 2003

By Gabriel Riveros, Ariel Balocchi, Andrzej Warczok, Daniel Smith

Blister copper from converting of copper matte is processed by fire refining prior to electrorefining. The fire refining consists of two steps: copper oxidation with impurities slagging and copper reduction. The classical batch process is carried out in vascular or reverberatory furnaces called anode furnaces. A new process for continuous copper fire refining has been proposed. The copper flows through two reactors in cascade, where is oxidized and reduced. The flow of a liquid copper through a ceramic packed bed increases the surface area and the rate of oxidation as well as the rate of reduction in the packed bed of charcoal. Mathematical modelling allowed for the design of a laboratory scale demonstration installation and industrial-pilot installation in Hernan Videla Lira Smelter (Paipote). The results have demonstrated the process feasibility and flexibility in operation.

Jan 1, 2009

By Aarne Kopanen

In recent years, various renovations have been carried out in the production chain of the Outokumpu copper refinirg process. The anode casting shop, which is the final integral production section at the Harjavalta copper smelter built in its original form in 1945, was fourxl unsuitable for technical and capacity demads during longer periods of operation, and a new casting shop was built in 1974. The electrolytic copper refinery of Outokumpu Oy at Pori was built in 1941, and subsequently expanded in two stages. Even with its present limited scale of production it has been fom important to mechanize the main operations. This work was started in 1967 with the design and construction of the starting sheet machine connected with the cathode washing and unloading machine as a combined unit. Mechanized treatment of anodes has gained advantage particularly from the new design of a highly automated anode casting shop. In the further development of the mechanization a stripping machine for, starting sheets was designed and installed, starting operation in 1974.

Jan 1, 1976

By C. A. Silva

The kinetics of chlorination of titanium-bearing raw materials has been investigated. For comparison purposes pellets of controlled macro-porosity, made of analytical grade TiO2 and anatase concentrate (Brazil) , have been exposed to different combinations of gas composition - CO, CO2, C12 -, gas flowrate and temperature. A thermogravimetric technique and an adapted grain model have been used in order to assess the influence of the several experimental parameters upon the chlorination behavior.

Jan 1, 1997

By Leijun Li, M. M. Mahapatra

"A three-dimensional finite element model with moving heat source was developed for pulsed-laser powder deposition (PLPD) process. Experiments were conducted to study the repair of superalloy components using the PLPD process. During the experiments, IN 625 powder was deposited on a superalloy substrate similar to IN 738. The process was modeled using three-dimensional finite element analysis. Element birth and death technique was used in the finite element model for simulating the deposition of powder layer on the substrate. A moving distributed heat source was used in the thermal model for realistic simulation of the process. Temperature dependent thermal material properties including enthalpy were used for the powder and the substrate in the transient thermal analyses. The fusion zones and peak temperature distributions of the deposits were predicted from the transient thermal analyses.IntroductionPoor weldability is a critical issue of superalloy repairing. The microstructural directionality of the superalloy components are disrupted when repaired by the fusion welding processes. Currently there is no widely accepted method to economically and reliably repair directionally solidified superalloys components. Pulsed laser powder deposition process (PLPD) is a promising repairing technique as the substrate is not severely affected by the heat source.In this study PLPD technology is used as the tool for superalloy repairing. In most of the land based turbine engines the directionally solidified nickel based superalloy similar to IN 738 [1] is used as the bucket material. The turbine engine blade tips are subjected to a combination of extreme operating conditions and corrosive environment. The tip of the nickel based turbine engine blades can be repaired using IN 625 material as suggested in the literature [1-2]. IN 625 is considered to be ductile and strong enough for the purpose of Ni based turbine engine blade tip repair[1-2]. During the present PLPD investigation, IN 625 powder was used as the deposit material on an experimental super alloy substrate similar to IN 738 superalloy used as the cast superalloy for the turbine engine blades."

Jan 1, 2012

By Bret Boster

Facilities at Amax Gold's Sleeper Mine process some 330 kt of high grade ore and 4100 kt of low grade ore annually to produce 6.8 t of gold and 7.8 t of silver. High grade ore is processed in a conventional milling facility employing gravity concentration, CIC and CIP unit operations for gold and silver recovery. Low grade ore is processed using heap leaching and carbon adsorption methods.. Presented are the evolution and descriptions of the Sleeper processing facilities and discussions of selected' operating results.

Jan 1, 1989

By K. H. Bech, S. T. Johansen

"The mass transfer at fluid-fluid interfaces due to turbulent agitation is investigated theoretically. In particular a theory is derived for interface stresses due to interface energy and surface renewal. This theory indicates that surface renewal may take place if the geometry is sufficiently large and if surface tension is sufficiently low.By using a model for a typical turbulent structure we compute the interface mass transfer for a stressless interface and a fully interface. Results for the general situation is not presently available. The computed results are used to derive analytical expressions for the mass transfer based on turbulent kinetic energy and free stream turbulent length scales.One important application of the theory is the mass transfer at the electrolyte side of the bath-metal interface in the Hall-Heroult process. For this process we show that mass transfer should be expected to be of the rigid surface type."

Jan 1, 1999

By Kouji Mimura, Manabu Kishida, Minoru Isshiki

"Purification of metallurgical grade silicon (MG-Si) by the plasma-arc zone melting method (PZM) has been examined. The process consisted in the horizontal displacement of a molten zone heated by Ar- and 10%H2+Ar- plasma-arc under atmospheric pressure. This technique, especially using hydrogen plasma-arc, promoted the segregation of impurities from the head to the tail of the bar and the vaporization of impurities of higher vapor pressures. Metallic impurities such as Fe, Ti, Cr, Mn,. Cu, Al and Ca were reduced to less than 1 mass ppm at the head side of the Si bar. Non-metallic impurities such as boron, phosphorous, carbon and oxygen were also reduced by the zoning effect and, furthermore, by activated hydrogen atoms dissociated in the high temperature plasma-arc according to the following reaction: Q (in liq.Si) + 2H = H20. Plasma-arc zone melting with hydrogen plasma has been recognized to become an effective purification technique of MG-Si for the production of a low cost solar grade Si (SOG-Si).IntroductionDemand of high-purity Si for solar grade silicon (SOG-Si) is supposed to be further growing in the near future. The purity of SOG-Si required for the photovoltaic cell is more than six nines. An expensive semiconductor grade silicon (SEG-Si) with the purity of around eleven nines has been used to satisfy the demand. Development of techniques and processes for the production of a low cost SOG-Si is therefore necessary [l]. Although many purification techniques, such as directional solidification, plasmaarc melting and electron beam melting [1-6], and processes, such as carbothermic reduction of high purity silica [7], have been examined and proposed for this purpose, a more efficient and practical purification technique is still required.In the present work, the purification of MG-Si has been investigated using a plasma-arc zone melting (PZM) technique developed by the authors. Plasma-arc melting, which is well· known as a useful melting method for various metals and alloys, has been recognized to be efficient for refining and degassing several metals if hydrogen is added to the plasma generating gas, resulting in the so-called hydrogen plasma-arc. For example, deoxidation of Fe, Co and Ta [8,9], decarburization of Fe [9] and removal of metallic impurities from Zr, Ta and Fe [10-12] have been reported. This excellent refining effect is considered to be caused by dissociated and activated hydrogen atoms formed in the high temperature plasma-arc."

Jan 1, 2000

By F. J. Hogan

In early 1982 Atlantic Cement Company, a wholly-owned subsidiary of Newmont Mining Corp. will come on line with a new water granulating grinding facility at Sparrows Point, Maryland to produce 800, 000 tons a year of separately ground granulated blast-furnace slag. The process and product will be unique to the United States. This paper will review some initial investigations undertaken to evaluate the cementitious properties of granulated slag. The effect of slag fineness on strength development is discussed and data is presented showing a relationship between glass content and hydraulicity and grindability of slag.

Jan 1, 1982

By Toshihiko Emi

The quest for cleaner steel is driven by increasingly stringent requirements from the manufacturing and construction industries. Key issues are the occurrence and removal of inclusions; These are discussed in the context of the unit processes of deoxidation, refining, transfer and casting of molten steel. Process thermodynamics and kinetics are also discussed. Recent progresses achieved and problems yet to be solved are elaborated, and an integration of the unit processes into a system to produce extra clean, steels with better performance is presented.

Jan 1, 1999

By R. L. Nyirenda

The use of ammoniacal ammonium carbonate (AAC) leaching for the treatment of carbon steelmaking EAF dust has been investigated on a laboratory scale. The experiments have been conducted on dust samples obtained from three European steelmaking companies. As received, the dusts were found to be toxic when tested according to current EPA toxicity testing procedures. Toxicity was on account of the leachability of one or more of the following elements: Ag, Hg, Pb, and Cd. Leaching experiments with concentrated AAC solution at 40 " C showed that zinc oxide present in the three dust samples, 60-80% of the total contained zinc, was rapidly solubilized. Data on the dissolution characteristics of Cd, Fe, Pb, Mg, and Mn are also presented. Toxicity tests conducted on residues of the leaching experiments found these to have leachates below past and current EPA toxicity threshold limits.

Jan 1, 1993

By Jose Antonio Silva Souza, Emanuel Negrao Macedo, Iara Ferreira Santos, Otacilio Dias, Luis C. A. Venancio

"The Bayer process alumina production generates 0.7 to 2.0 ton of bauxite residue (BR) and an average of 1.0 ton of C02 per ton of alumina produced. The direct reaction of exhaust gases to reduce the alkalinity of the BR may allow a triple gain: improve the storage conditions, open a range of new applications for BR and sequester from 16 to 102 kg of C02 per ton of alumina. This paper shows the measurement of C02 captured during a pilot scale reaction of a suspension of BR in water with flue gas, produced from direct oil burning. Three different types of reactors were used: one spray tower and two packed columns. The inlet and exhaust gases were analyzed using electrochemical and non dispersive infrared sensors. The pH of the suspension was monitored during and after the reaction to evaluate the buffer effect.IntroductionAlumina is mainly produced from refining bauxite using the Bayer process. This process consists of extracting the aluminum oxide through its dissolution in caustic soda and the separation of insoluble residues. The remaining bauxite residue (BR) although not particularly toxic, poses risks to the environment due to the large volume and its reactivity. According to the latest technology it is stacked on sealed deposits specially constructed. To date the vast majority of the bauxite residue that has been produced was stored and were not incorporated into any existing production processes to significant amount with exception to some extent of the sintering process residue at Russia and China [l]. On the other hand, a strategic goal was set in 2010 by the Bauxite and Alumina Committee of the International Aluminium Institute (formed by the majority of the industries) to reuse 20% of BR in 2025 [2]. China has established the same objective for 2015[1].This paper is a sequel of two others presented at TMS 2010/2012 [3-4] and describes:• A pilot plant assembled for testing the carbonation process of BR with gaseous effluents similar of the refining process.• The methodology used to measure the amount of C02 captured during the carbonation process.• The results of the carbonation process, the C02 capture and the buffering effect of the pH.This process is studied in order to consume minimal power and use the effluent as efficiently as possible in different reactors from low cost to ultra high performance. The process is designed for minimizing the power consumption and equipment investment."

Jan 1, 2013

By A. Lackner

Using the CFD software package FIRE, the smelting process inside a cyclone reactor is modelled. The fluid flow is calculated 3 dim., using different turbulence models. The effects of design parameters (length and diameter of the cyclone, concentrate feeding tangentially or from the top,..) and operating conditions are investigated. Single particle traces illustrate how to increase particle retention time before the particles reach the liquid film flowing down the cyclone wall. Moreover a two phase flow approach is developed, based on the "Discrete Droplet Model". The position, velocity, diameter and temperature of each reacting particle is described. The results show the advantages of top concentrate feeding, large height/width ratio of the tuyeres and increasing number of tangentially gas inlets.

Jan 1, 1995

By Debbie Marshall

Process water is an important consideration in the development of a nickel laterite project. Depending on the location of the ore body, sufficient fresh water may not be available and it may be necessary to use seawater (or saline groundwater) for ore preparation. This introduces various species, which have major effects on materials of construction and leaching chemistry. This paper summarizes batch testwork completed at the Falconbridge Technology Center. The leaching behaviour of eleven different laterite ore samples were compared using seawater and fresh water. For brevity, six of the eleven samples are reported here-the other five samples showed similar results. Each ore type was leached under identical conditions in both freshwater and seawater and the leaching chemistry compared. The batch test results were confirmed in a continuous pilot plant, and leach kinetics for the two systems were compared. Keywords: high pressure acid leaching, laterites

Jan 1, 2004

By G. A. Brooks

Increasing interfacial area through gas injection is one of the main methods for accelerating reaction between slag, metals, and gases in modern pyrometallurgical reactors. In slag-metal reactors, the generation of a large number of metal droplets into the slag phase through high gas velocity has a much larger effect on the overall kinetics compared to the enhanced mass transfer through mixing. Top blowing technology generates large interfacial areas (>300 m2/tonne) through high impingement gas velocity at short distances between the exit of the injection lance and the metal-slag interface. Phase separation may become a limit at the case of very high interfacial areas, though there is still only limited understanding of the trajectories of metal droplets in slag-metal-gas emulsions.

Jan 1, 2003