Search Documents

The purpose of this paper is to present validation studies of the mine-fire simulator using data gathered from an actual mine fire which occurred in November 1991 at the Pattiki Mine. To develop the model of the ventilation system with the fire in this validation study, the following adjustments were made: (1) flow and gas distribution in the entire ventilation network, and (2) fire parameters matching the data recorded by the monitoring system. After close correlations between simulation and real data were achieved, additional analysis of the ventilation system with the mine fire was performed. Presented and discussed in this paper are the following stages of the fire at the Pattiki Mine: (1) early fire (before the fire was detected), (2) preparation for and fire fighting with water, (3) fire sealing, and (4) fire extinguishing. This study evaluates the suitability of the computer software package for modeling underground fires. The paper also discusses the importance of the on-line monitoring system for the validation process.

Jan 1, 1995

By V. M. Lepetic

Large tonnages of copper and molybdenum sulfide ore are treated by flotation. Substantial savings could be realized, particularly in high-capacity concentrators, by use of a simplified flotation technique involving lower reagent consumption. Chalcopyrite and molybdenite from some deposits can be floated by use of only a frother as a single flotation reagent; acceptable concentrate grade and recovery can be obtained. Separation of molybdenite from copper sulfides may become simpler and less costly. The genesis of the ore and the ions present in the flotation pulp liquid phase appear to be the major success-determining factors.

Jan 1, 1972

By Earl Cook

A high-energy economy based on fossil fuels is in fundamental conflict with an ideal of clean air, clean water, undisturbed scenery, and maintenance of fragile ecosystems. There is an inevitable trade-off between the material standard of living of a modern society and the conservation of its environment. During the past four years, some of the costs of environmental protection have been internalized in the energy-flow system of the United States. The cost of bituminous coal and fuel oil usable under new air-quality standards has doubled or more. The cost of mining coal underground has risen because of a 20-30 percent reduction in productivity resulting from new environmental health and safety legislation; the economic impact of proposed surface-mine regulation may be equally severe. The cost of producing electric power has been rising at a 12 percent annual rate because of environmental costs, and would be climbing still more steeply were it not for the continued forced subsidy of natural-gas consumers by natural-gas producers. The efficiency of the automobile, already a monument to the triumph of self- indulgence over economy, is being further decreased by addition of anti-pollution devices. Part of the recent sharp rise in agricultural costs stems from the fact that five energy units of fossil fuel go into U.S. agriculture for every energy unit of raw food that leaves the farm; further large injections of fossil-fuel energy occur in the transport, processing, and refrigeration of farm products.

Jan 1, 1974

By W. Robert Power

Dimension stone includes a wide variety of natural materials that are put to an equally wide variety of uses. It is possible to classify dimension stone according to the end use to which the stone is put or according to the lithology of the stone. Both schemes are used by the United States Bureau of Mines in the annual Minerals Yearbook. The 1969 Yearbook lists 15 specific uses and has additional miscellaneous catagories. The same Yearbook lists five specific rock types or lithologies, and also includes a miscellaneous category. In a short presentation it would hardly be possible to list and define all these categories, much less discuss the evaluation of deposits with regard to all possible combinations. Besides, I am only slightly familiar with some of the uses and their requirements. I have therefore chosen to limit my remarks to some special problems in evaluating dimension stone that is to be cut and finished to specific sizes, tolerances, and finishes for use in buildings and some monuments. This use class is called cut stone in the Minerals Yearbook. In terms of dollar value it is the largest single use category. In 1969 the dollar value of cut stone was $29,122,000 which is more than twice the value of the next largest category. For those of you who are interested in other use applications of dimension stone I suggest that you start with recent articles by Bowles (1960), Currier (1960), and Barton (1968).

Jan 1, 1972

By M. Ploc

The grinding process in the mining industry has seen an increased throughput to accomplish greater production and lower overall production costs. Up to 8-9 MW, a single motor can be connected to drive the mill through a pinion and ring gear. Above the single-pinion drive limit, the dual pinion approach was developed to allow two drive motors to be used. This allowed the mill input power to be increased to 16-18 MW. Recent developments in clutch and ring gear materials and design are allowing greater input powers of up to 20 MW to be considered. To avoid damage to the ring gear by uneven load sharing between the two motors, it is critical that the two machines accurately share load. This is typically achieved by either drives capable of controlling load torque between motors or using a GE proprietary control system that accurately controls the load torque from each motor.

Jan 1, 2010

By G. L. Brooke

At present, there are two known cobalt deposits in the 48 contiguous states. This paper is a brief description of one of these deposits. It is a Mississippi Valley type deposit, but somewhat atypical in that the metal of greater interest is cobalt as opposed to lead, zinc, and copper. The history and present work are outlined along with a discussion of the geology and mineralogy.

Jan 1, 1981

By Gregory M. Rumbaugh, Todd Kostecki, Christopher Mark

From 2015 to 2021, five massive pillar collapses occurred at four underground stone mines in the eastern United States. These events resulted in powerful airblasts that damaged mine infrastructure and mobile equipment, seriously injured miners, and disrupted underground travelways. Each of these pillar collapses propagated through the overlying strata, causing a subsidence basin on the surface. Pillar collapses are particularly hazardous for miners because they can occur with little warning and can affect miners that are far from the pillar collapse area. The following case studies show that certain factors may increase the likelihood of a pillar collapse. For instance, each of the five events involved the collapse of at least twelve benched pillars with width-to-height ratios (w/h) of 0.8 or less. This study elaborates on

By Terry O. Arney

This paper is a description of the digital Data Acquisition and control System that is installed at Cities Service's Pinto Valley Concentrator. Pinto Valley Concentrator ? The Pinto Valley Concentrator (5, 41 is located approximately seven miles west of the town of Miami, Arizona. The Concentrator is situated south of the open pit mine and was designed to process 40,000 tons of ore per day with an average grade of .45% copper. The comminution process consists of primary, secondary, and tertiary crushing, and single-stage closed-circuit grinding 161. Concentration of the copper sulfides is by means of froth flotation. Concentrates are transferred to the Inspiration Consolidated Copper Company smelter in Miami, Arizona through a slurry pipeline.

Jan 1, 1976

By Douglas M. Dwosh

INLAND STEEL COAL COMPANY'S experience with a gypsum cement, with and without fiber glass filler, indicates that the concept of utilizing standard rock dust equipment to dry handle and apply gypsum cement as a mine sealant is feasible, simple and economical. Prior to 1975, Inland had casually experimented with a few sealants and had discussed the advantages and shortcomings of other sealants with various users. Hower in mid-1975, Inland foresaw the need to seriously acquire a practical sealant system. There were nearly a dozen sealant materials on the market at that time: silicate-based materials, Portland cements, vermiculite cements, gypsum cements, and magnesium-oxysulfate cements, each with their own fillers and additives. The applicating equipment ranged from simple to complex: wet mix or slurry machines operating on either a batch or continuous basis, high viscosity pumps, and pneumatic, dry conveying machines with water nozzles. Compounding the selection process, two or more products could often be used with the same machine, or a given material could be successfully applied with more than one type of machine.

Jan 1, 1976

By W. C. Baver

Even before the energy crisis developed in the early '70's, considerable research world-wide was being directed towards the development of schemes to both reduce the energy requirements and to reduce air pollution emissions associated with the manufacture of glass. In many cases the sought-for solutions would benefit both objectives. If, for example, the glass batch could be consolidated into such compact forms as briquettes or pellets, they could be preheated in a moving-bed heat exchanger with the high-temperature exhaust gases from the glass furnace. Lower furnace temperatures would thus be possible with a corresponding reduction in heat losses and total fuel consumption. Moreover, the lower temperatures would also reduce the amount of nitrogen oxides generated in the furnace and emitted to the atmosphere. Many tests on consolidated glass batch have been run in many countries. In some cases, extended tests on production furnaces have also been included in the programs. For various reasons, however, none of these has proved to be economically attractive. The current, but temporary lull in the rapidly rising cost of energy which has been with us in recent years, has reduced the push for research for energy saving means for melting glass. A few of the current programs will be discussed. Since raw material requirements, primarily physical in nature, are affected by some of these schemes, these will also be considered.

Jan 1, 1986

By Alex Stewart

Most iron bearing ores treated by the R=N Direct Reduction Process yield products lower in phosphorus than the initial ores. The sulfur is also removed and generally is in the range of 0.02 to 0.05 percent in the final R=N product, independent of the sulfur content of both the ore and carbon fuel used. The mechanism and thermodynamic justification of the principal reactions leading to the removal of both phosphorus and sulfur and the control of sulfur in the iron concentrate produced are discussed and supported by the results of laboratory experiments. In substantially all iron ores (containing up to 4% sulfur as sulfate) and solid carbon fuels (containing sulfur from 1 to 8%) tested, the rejection of sulfur has been in the order of 90-95%, with not more than 0.02 0.05% sulfur in the final metallic iron product. With respect to phosphorus-bearing iron ores ranging up to 0.70% P205, the rejection to tailings has been in the order of 70-95%, resulting in not more than 0.03 - 0.07% phosphorus in the final product.

Jan 1, 1958

Water contact angles in the air/water/francolite, fuel oil/water/francolite and fuel oil/water/quartz systems were measured to describe the wetting characteristics of these minerals. It was found that white francolite is more hydrophilic than black and tan francolite both in the absence and presence of fatty acid addition. The contact angle measurement results do not correlate very well with the flotation response and it appears that kinetic aspects of the bubble attachment process play an important role in the francolite-fatty acid flotation system.

Jan 1, 1997

By James Paone

Subsidence movements have damaged houses, schools, streets, and public utility lines in some undermined sections of Belleville and Maryville, Ill. In cooperation with local officials and the State of Illinois, the Interior Department's Bureau of Mines is sharing experience in backfilling abandoned coal mines to demonstrate that bituminous coal mine workings in south-western Illinois can be successfully backfilled and subsidence-prone areas stabilized. Subsurface investigations revealed that mine workings are dry and underlain by underclay deposits susceptible to instability upon wetting. Backfilling will therefore be accomplished by pneumatic injection instead of the hydraulic methods used in previous subsidence-control projects.

Jan 1, 1977

By J. A. Organiscak

This paper describes the research con-ducted on bit wear and respirable dust generation conducted by the US Bureau of Mines (USBM) and West Virginia University (WVU), a member of the Generic Technology Center on Respirable Dust. The USBM investigated wear, energy and dust characteristics of various conical bit designs when cutting rock. WVU studied the functional relationships between wear, cutting force, energy, and dust of one conical bit type when cutting coal. The objective of the USBM study was to identify qualitative bit selection guidelines for cut-ting rock; WVU's research objective was to determine optimum bit replacement guidelines. These research studies both found that bit geometry (a function of bit design and wear) influences energy consumption and dust generation. Bit selection and replacement recommendations are given.

Jan 1, 1995

By R. J. Zagrocki

Rekindled public concern about lead toxicity has intensified the awareness of lead-bearing materials in contact with the environment and the human population. Lead's common association with other metals makes the increasingly restrictive lead standards a primary concern for a large number of metal and metal-related industries. In commercial scale demonstration tests with lead-bearing wastes, the HRD Flame Reactor process has a demonstrated ability to separate and recover over 95% of the lead as a recyclable oxide, while rendering the remainder of the material as vitrified, non-leaching, and nonhazardous co-product. Recent Flame Reactor process tests and preliminary cost data for secondary lead soda slag are highlighted.

Jan 1, 1992

By Ronald M. Tipton

Freeze and thaw deterioration is a serious problem In con¬crete pavements. The main cause of distress Is thought to be the pore structure of coarse aggregate. In an attempt to characterize deleterious pores, the Iowa Pore Index test and the Expected Durability Factor, as Calculated from the mer¬cury intrusion porosimeter, were devised. This study Included freeze-thaw and sodium and magnesium sulfate soundness testing of sixteen carbonate aggregate samples. In addition, the Iowa Pore Index and the Expected Durability factor were determined for each of the samples. All of the Above mentioned physicochemical parameters were examined using bivriate correlation analysis with the In¬tent to evaluate the effectiveness of the Iowa Pore Index and Expected Durability factor for predicting the frost dur¬ability of an aggregate. The results from the bivariate correlation analysis showed no significant correlation, between the Iowa Pore In¬dex And- Expected Durability factor with the other physico¬chemical parameters investigated. Rust interesting is that the Iowa Pore index predicted that All of the tested samples would resist freeze-thaw failure, whereas the Expected Durability factor predicted that -ash sample would he non-durable.

Jan 1, 1987

By C. L. Karr

Researchers at the University of Alabama have developed a method for producing fuzzy linguistic models of mineral processing equipment directly from engineering data. These fuzzy linguistic models rely exclusively on data collected from the processing systems being modeled and do not presuppose an understanding of the physics of the system. The fuzzy linguistic models use descriptive rules and explicit membership functions that provide a precise, nonmathematical description of the processing equipment. A genetic algorithm is employed to simultaneously select rules and tune membership functions used in the fuzzy models. The result is an extremely flexible approach to modelling that is applicable in a variety of linear and nonlinear systems. The effectiveness of this approach to modelling is demonstrated using a four-input, two-output model of a grinding circuit.

Jan 1, 1996

By D. C. Martin

Construction of the Cerro Colorado on-off leach pad in northern Chile required placement of approximately 3,000,000m3 of fill over a P1an area of approximately 600,000m in irregular terrain with relief of up to 40m. Earthwork construction was completed in approximately six months using mine waste which was placed in 4 to 6m lifts using mine haul trucks. The lift thickness was reduced and the compactive effort increased in the upper 10m to enable development of a mat and additional resistance to possible differential settlements under dynamic (earthquake) conditions. A single 80 mil (2mm) HOPE liner was used below the leach pads and this was protected from the loading and unloading equipment using an engineered liner system consisting of screened sand, gravel and silt from local sources as the bedding and cover layers, and a heel of screened gravel and primary crushed low grade ore. Settlement monitoring, field testing and subsequent assessments of liner performance have indicated an adequate design was achieved and the project proceeded with considerable savings in time and construction costs.

Jan 1, 1995

By J. W. Langhans, B. D. Blake

The U. S. Bureau of Mines has been investigating the application of thiosulfate to recover gold directly from low grade refractory carbonaceous ores for the past four years. Statistical experimental methods were used to determine the effects of various leaching parameters on both gold extraction and thiosulfate consumption. Seven variables were investigated, including thiosulfate, copper, ammonia, sulfite, and sulfate concentrations, leaching time, and leaching atmosphere. This information was used in face-centered cubic (FCC) surface response experiments to define the optimum leaching conditions for a low grade ore. Two models were generated from the data to predict gold extraction and thiosulfate consumption as a function of the leaching parameters. The models predicted a gold extraction of 67 pct and reagent consumption of 2 kg [S2032/mt ore at 0.25 M S2032-, 0.0014 M Cu2+, 0.27 M NH,OH, 0.00625 M SO;-,] and leaching for 16 h. Actual tests resulted in 62 pct gold extraction with 0.93 kg S2032- consumed/mt ore. Subsequent column leaching tests have further demonstrated the viability of applying this technology to recover gold from carbonaceous ores without first pretreating the material. Gold extractions in the column tests ranged from 69 to 78 pct with thiosulfate consumption ranging from 0.4 to 5.4 kg/mt ore. These results compare to <5 pct gold extraction using standard cyanide leaching conditions.

Jan 1, 1996

By R. Zhang, S. Azam, S. Liu, J. H. Golbeck, V. Kurashov, S. Bhattacharyya

Free radicals (FRs) present in coal dust directly influence the interaction behavior between lung cells and dust particles. FRs are atoms or groups containing unpaired electrons, with strong chemical reactivity and a short lifespan. FRs which are quite persistent in natural environments, termed environmentally persistent free radicals (EPFRs), have recently received much attention as new environmentally hazardous substances. EPFRs present on coal dust serves as an active intermediary to catalyze reactive oxygen species (ROS) production by oxygen molecules endangering mine workers’ health. Many EPFR species may be bonded to the particle surface or trapped within the particle during coalification and can be modified with progressive size reduction through cutting at the mining face or crushing/pulverization in the plant. This study measured EPFRs for lignite, sub-bituminous, and anthracite coal dust at various sizes. We especially focused on EPFRs for submicron coal dust prepared by cryogenic methods. The outcome of this study will directly improve the free radical-dependent toxicity quantification and ultimately contribute to the size-dependent coal dust toxicity quantification.

Mar 2, 2022