Search Documents

By M. SIDDARAJU, Rameshwar Sah, T. Umadevi, K. S. SRIDHARA, M. RAJU, GANESH SHETTY

With the depletion of high-grade iron ore resources, the utilization of existing low-grade iron ores, fines and tailings with effective beneficiation is inevitable to meet the iron and steel industry’s required specifications and demand. JSW Steel Limited is operating a 17-mtpa beneficiation plant at its Vijayanagar site in Bellary in Karnataka, which produces nearly 50 to 54 percent concentrate as sinter-grade fines. The sinter base mix consists of iron ore fines that are smaller than 10 mm, with 41 percent smaller than 0.150 mm; washed ore that is generally smaller than 3 mm and bigger than 0.150 mm, with 3 to 9 percent smaller than 0.150 mm; beneficiation plant concentrate, with 97 percent smaller than 0.150 mm; limestone; dolomite; coke breeze; lime; sinter return fines; direct reduced iron (DRI) fines; and micropellets produced from steel plant waste. Using more washed ore in the sinter base mix affects the sinter quality. Ball formation in the mixing and nodulizing drum is an important step in sinter making and requires sufficient quantity of smaller than 0.150 mm fines. Optimization of fines in the sinter base was carried out by replacing the smaller than 10 mm iron ore fines with washed ore. Size analysis, study of the granulation index (G index) and optimization of moisture with respect to sinter bed permeability were carried out to optimize the proportion of smaller than 0.150 mm fines in the sinter base mix as adhering material. This study explores the optimization of fines in the sinter base mix for ball formation to achieve higher sinter quality and productivity with higher sinter bed permeability.

By Onur Golbası, Berk Gokce

Investment decisions in the mining industry are complicated by sector-specific uncertainties. This study presents a multi-submodule system dynamics model to capture the dynamic complexities of decision-making across mineral property development stages. The model includes five interconnected subsystems: valuation, production, growth strategy, demand, and finance. Developed through system decomposition, expert input, and literature, the model is tested on a hypothetical copper mine with 850 ktpa capacity and 1% cu grade. Simulated over five years with quarterly steps, it estimates an enterprise value of $78.9 million and a target growth rate of 11.2%. Results highlight the significant effects of operating costs, capital policies, and inflation on free cash flow, and the critical role of mineral reserves in sustaining growth. This model supports strategic investment analysis across different minerals and development phases, offering mining investors a robust tool for optimizing decisions.

Feb 22, 2026

By Mark C. Williams, Shunsuke Managi, Noriko Hikosaka Behling

Particle processing is a key to using solid particles in fuel cell applications. Selectivity with regard to reactivity, impurities, etc. is an important feature and the treatment of particle surfaces could greatly impact the performance of direct carbon fuel cells. Solid fuel particles will become increasingly important in the future. Present energy conversion systems for solid fuels are too inefficient. New energy conversion systems for solid fuels with higher energy conversion efficiencies are possible. Fuel cell technology is a key technology in these new conversion systems. The direct carbon fuel cell (DCFC) operates on carbon particles obtained from a variety of solid fuel feedstocks. The DCFC is the only fuel cell designed to directly oxidize carbon particles in a special anode chamber. The particles are generally graphite structure with high purity. The electrolyte used is the high temperature solid oxide, molten carbonate, or hydroxide electrolyte. Since a pure stream of CO2 is produced, the stream can easily be sequestered and disposed. Pure carbon dioxide produced as a by-product would also have a market in many industries. A well-defined technology roadmap identifying key research and development (R&D) issues is necessary to provide a framework for the development of these systems and to prevent entrenchment in inherently inefficient technologies. This review paper describes the direct carbon fuel cell and its system, how it works, the developmental status, the characteristics of the carbon particles needed, and the research and development issues for the technology

By Thomas F. Connors

The end of an era is here. The pony-express era of industrial relations in the coal industry is ending. Those professionals who know it must end to insure the industry's future are happy, relieved, but somewhat saddened. They are sad because it did have its elements of suspense, thrills, frustrations, and at times, plain fun. The days of the Company town are ended; the wildcats are declining; violence (while a big part of today's industrial relations) is beginning-to decline. The spirit of sound industrial relations is beginning to take hold. This has to happen for the industry to compete in today's economy and it is causing major changes for those who have grown accustomed to the pony-express type industrial relations.

Jan 1, 1981

By B. Mishra, Q. Shi

Numerical simulations have been used to investigate roof fall in the past decades. Comparing to the continuum based methods, the discrete element method has been well recognized for its excellent performance in simulating large strain problems and fracturing processes in the rock mass. However, the discrete element method has its limitations. When simulating a large-scale problem, a large number of particles are required, which consumes significant computational resources. In the present study, a 3D numerical model coupled with the finite-difference method (FDM) and the discreteelement method (DEM) was created to simulate the laminated roof failure in an eastern coal mine in the US. In the FDM-DEM coupled model, the laminated roof of the entry is represented by an assembly of bonded particles using PFC3D. The laminated roof is simulated by adding parallel discontinuities. The discontinuities are given certain stiffness and strength in the model. The ribs, floor, and far-field surrounding rock are represented by continuum zones using FLAC3D. The strength of the discontinuities is varied sequentially and the fracturing of the laminated roof was analyzed with respect to entry advance. The results showed that the laminated roof fractures along the discontinuities while an intact roof fractures in a dome shape. Increasing the strength of discontinuity could enlarge the tensile zone inside the laminated roof and hence change the crack distribution. In addition, the crack quantity in the laminated roof behind the advancing face decreases with the increment of discontinuity strength while this trend is not occurring ahead of the advancing face. The simulation demonstrated that coupled method using PFC3D/FLAC3D can reproduce the laminated roof failure in underground coal mines.

Mar 2, 2022

By Irina Chernyshova, Erik Larsen, Hanumantha Rao Kota, Vladislav Slabov, Garima Jain

The mining industry faces pressure to provide metals for the green digital shift using sustainable technologies. This study evaluates biosurfactants as collectors for ultrafine and coarser particles of hematite and malachite, aiming to improve the flotation of ultrafine particles.

Jun 1, 2023

By Donald Hulse

"Mining has been a source of controversy for at least 500 years. “Since there has always been the greatest disagreement amongst men concerning metals and mining, some praising, others utterly condemning them…” (Agricola, 1556). In 2016, it is widely recognized that mineral resources and reserves must give due regard to the social license in order to operate.“Most commonly, the social license to operate (SLO) is understood to refer to ‘the ongoing acceptance and approval of a [project] by local community members and other stakeholders that can affect its profitability’ (Moffat, 2014).” “Social License to Operate has gained traction, in part, because it is also a concept which – while remaining poorly, technically defined – is generally easily and widely understood by community stakeholders (Bice, 2014).”A generation ago we learned that mining is based on a stable platform supported by three pillars, geology, mining and metallurgy. The three-legged stool is a very stable structure (Fig. 1).In 2016, it seems that we have added some other legs to the stool (Fig 2). The Australasian Code for Reporting of Exploration Results, Mineral Resources and Ore Reserves (JORC Code) addresses “social, and governmental factors…” (JORC 2012), and refers specifically to social license in Section 4 of the Report Template “Estimation and Reporting of Ore Reserves.”The Canadian Institute of Mining, Metallurgy and Petroleum (CIM) Guidelines refer to “environmental, legal and social data…(CIM 2003).”Compared to these, the 2014 SME Guide is positively verbose stating “a discussion of any potential social or community related requirements and plans for the project and the status of any negotiations or agreements with local communities,” (SME 2014) although in all cases the scope of this disclosure is left at the discretion of the competent person.When there are more than three legs on the stool, it is imperative that all legs be constructed exactly to the design. Any one or more legs that are out of alignment will cause the stool to wobble.Engineers are trained to create designs to meet specifications. Loads can be estimated, forces calculated and cost studies completed that will lead to, not only a stable design, but the most efficient design that meets the specifications."

Jan 1, 2015

By A. G. Yapo, T. W. Camm

"All-in sustaining cost is a metric used by mining companies to reflect the cost of gold mining in a consistent format useful to both investors and mining professionals. Cost reporting focused on the direct cost of mining and processing ore was summarized in the non-GAAP cash cost developed by the Gold Institute in 1996. In 2013, a group of mining companies, working with the World Gold Council, developed a more inclusive approach to reporting costs designed to solve the dilemma of showing a more comprehensive reflection of recurring costs involved in producing gold, without discouraging investors. INTRODUCTION Mining today plays a key role in the development of our civilization as a source of essential raw material and provider of essential fuels, producer of jobs, and a factor in support of the international balance of monetary payment (Camm, 2014). Professionals in mining locate, develop, design and manage ore deposits in an environmentally safe and profitable manner. As mineral deposits become increasingly scarce, new challenges face the industry. A current trend is to an increased emphasis on underground mining techniques for deeper deposits. Operations are safer today than before as companies understand better their work environment and the importance of mining responsibly. A continual challenge for the industry is accurately reflecting the costs and selling price of ore. An enduring characteristic of mining is the situation where the market typically determines the price of a commodity; the main control a company has on the bottom line is to control the cost of production. An attempt to bring light and clarity on the cost of their business will give a better idea to investors on the true profitability of the mining business. Gold producers face this struggle to accurately reflect the cost of production while also seeking to attract the interest of the investment community (Hill, 2013). In order to have a consistent format to report on their production costs, leading gold producers through their alliance inside the World Gold Council (WGC), worked on the adoption of a new cost framework: the All-in Sustaining Cost (AISC) and All-in Cost (AIC). Since 1996, the traditional cash cost reporting has focused only on the mining and processing costs incurred in mining an ounce of gold, which included the costs of goods sold (labor, energy, and consumables costs) and royalties (Table 1). But cash cost reporting ignores many important aspects, like sustaining capital, general and administrative expenses, and site rehabilitation at the end of the mine life (Whelan, 2013). The cash cost was used to attract many investors into the business. In fact the high gross margin (sales minus cash costs) has been promoted the past decades by the industry instead of the net or operating margin. As a result, even when the gold price was high, nearly $1900 per ounce in August 2011, gold producers were not reporting excessive profits in their cash flow / income statements, to the disappointment and incomprehension of investors (Milstead, 2014). The truth was simply that the other costs omitted in the traditional cash cost were reducing the apparent profits."

Jan 1, 2017

By Arif Emre Dursun

The aim of this study is to present hazard classifications of location, type and causes of accidents in the Turkish coal-extracting industry using the analytic hierarchy process (AHP). In this study, fatal mine accidents were analyzed by pairwise comparison and weighting, and the most important hazards were identified by determining the effective main and sub-criteria among location, type and causes of accidents. For this purpose, first-, second- and third-level hazards consisting of location, type and causes of accident were determined by using the data of fatal mine accidents in underground and openpit coal mining in Turkey between 2010 and 2020.

May 1, 2024

By Melvin W. Jackson

The study of the excavation of large spherical cavities in salt formations first became of interest in 1958 when it was recognized that a large cavity could be of value in the study of the detection or concealment of underground nuclear explosions. Previously unpublished studies are reported in this paper and other studies reviewed relating to the excavation of large cavities in salt by mining ad by solution. Special emphasis is placed on the utilization of the Tatum salt dome (about 22 miles southwest of Hattiesburg, Mississippi) for the proposed site of a large excavated cavity. The U. S. Atomic Energy Commission has recently been studying such a cavity as Project Payette, but no details have yet been published. If Project Payette is determined feasible and work funded, it would eventually involve the firing of a nuclear explosive at the center of a large cavity.

Jan 1, 1969

By Martin H. Stanczyk

The Organic Act of 1910 established the Bureau of Mines and gave it authority and responsibility for conducting research on separation, recovery, and recycling of waste products and scrap generated by the mineral and metals industries and the consuming public.(1)1 It was apparent to our Nation's leaders even then that mineral resources, once mined, are irreplaceable and that the development of methods for recycling the values contained in wastes would be required to solve the problem of even¬tual scarcity, Estimates of the increase in per capita consumption of mineral resources in this country indicate that the consumption of metals, minerals, and fossil fuels by 1980 will be double that consumed in 1970 (2). The United States can expect to meet its future mineral needs in three basic ways: the first is through increased production of primary raw minerals; second by increasing imports from foreign sources; and third by recycling secondary materials and metals that were formerly discarded as waste. Rather than consider these

Jan 1, 1972

By W. R. Peters

An experimental hole-to-hole seismic probe system has been developed for use in coal measure geology as a means of determining the structural conditions of coal seams. The source probe produces a 500-joule electric arc discharge whose seismic wavelet has a spectrum in the 200 to 2,000 Hz frequency range. Low compliance hydrophones contained in the source probe as well as in a separate seismic detector probe are matched to the frequency range of the source. Both probes are constructed with 5-72 cm diameter housings. The transducers in the probes are equipped with fluid-inflatable boots to permit operation in either wet or dry boreholes. Preliminary tests in vertical boreholes drilled 213 m apart in sedimentary rock formations show reliable operation and useful seismic propagation measurements along horizontal and oblique paths up to 232 m in length. Because the seismic wave- let has an accurately repeatable waveshape, multiple shots and signal averaging techniques can be used to enhance the signal-to-noise ratio and extend the transmission distances.

Jan 1, 1985

By Thomas Konstantis, Spyridon Konstantis, Panagiotis Spyridis

"Tunneling and Underground works are unequivocally subject to a diversity of inherent uncertainties associated with the geotechnical, hydro-geological and environmental regime that surrounds them. On many occasions, these uncertainties can provoke loss events of considerable consequences. The present contribution elaborates on losses that the insurance market has suffered in the recent years, following a construction failure event. These losses are being considered and analysed on a quantitative basis through evaluation of cost related data, with explicit discretization of the applied construction methodology and of the subsequent developed failure type since both of which are considered of major importance. Given the identified persistence and regularity of some loss-contributing factors, recommendations are provided on the basis of a proactive risk engineering management approach that are envisaged to reinforce the understanding of project risks and alleviate the incurred insurance cost. 1 INTRODUCTION The underground construction sector has always been a very challenging area for all involved parties, including the insurance market. Main reason for that remains the uniqueness of the uncertainties sources and the subsequent inherent risks that the tunneling and underground projects are exposed to. In many instances, these risks materialize, leading to loss events with substantially high impact on reinstatement cost and incurred delays, which depending among others on the insurance coverage will have to be bared by the Insurance market. In the recent decades and as the tunneling industry boomed and expanded with many major and significant projects undertaken around the world, the insurance market was faced with additional challenges. Increased competition during tender coupled with the scale and complexity of the projects and politically driven decision making exerted pressure on the project timelines, completion dates and budget. The pressure for on-time or even early project completion- to avoid liquidated damages or achieve bonus payments, respectively- along with cost reduction efforts and the incentive for innovative failure events. That, in turn, put additional pressure on the Insurance market which had experienced a significant amount of losses with substantial cost. One of the triggered mitigation actions was the introduction of the Code of Practice for Risk Management of Tunnel Works (ITIG, 2006 & 2012; MunichRe 2006, Wannick, 2007, Spencer, 2008, Adeyemo, 2011)."

Jan 1, 2016

By Cody Giroux, Homer Scurlock, Michel Wasag

Silica and Crystalline Quartz exposure continues to be a serious health threat to nearly 2 million workers in the United States, including more than 100,000 working in high risk jobs such as abrasive blasting, foundry work, stonecutting, rock drilling, quarry work, mining and tunneling. The primary focus of this study is to identify the best methodology to reduce particulate-laden air and limit/eliminate exposure to respirable dust with silica/crystalline quartz during tunneling operations. This study focuses on two de-dusting systems employed on similar tunnel construction projects. The first project is the Coxwell Bypass Tunnel located in Toronto, Ontario Canada. The second project is the Westerly Storage Tunnel located in Cleveland, Ohio. The Toronto project is utilizing a wet de-dusting system. The Cleveland project is using a dry de-dusting system. The objective is to determine which system provides the best protection and suitability to capture, remove and ultimately reduce respirable concentrations of silica/ crystalline quartz to safety and healthy levels in underground tunneling activities.

Jun 13, 2021

By Franziska Günther, Helmut Mischo

The calculation of costs for an underground mine, as well as the planning of the equipment and materials to be used, is a complex and time-consuming process. The estimation depends on a multitude of parameters, and all mining processes are interconnected. A novel tool has been developed that enables automated calculation of underground mines and allows for the comparison of the effects of changing individual parameters. Previously, changing individual planning parameters often necessitated a complete recalculation of the mine. The newly developed calculation tool provides an innovative planning aid that allows for more efficient and accurate mine planning and cost estimation. The tool enables the user to implement continuously up-to-data costs and prices. This allows for more accurate planning data and results. The underlying concept of the calculation tool, its implementation at a planned quartz porphyry mine in Germany, and the verification of the tool at an existing underground mine will be presented.

Feb 1, 2025

By J. K. Wilmshurst

Absorption, emission and reflection techniques for the study of [molten] inorganic materials at high temperatures have been critically examined. In general, the reflection technique is the most satisfactory for tine study of pure materials, while the absorption, and possibly also the emission techniques, may be useful for studies of certain dilute solutions. In the present investigation infrared emission spectra for sodium nitrate and silver chloride were obtained together with absorption spectra derived from reflectivity data by the method of Robinson and Price for sodium nitrate, silver chloride, lithium and potassium fluoride and their 1:2, 1:1 and 2:1 mixtures and for solutions of zirconium tetrafluoride in lithium-potassium fluoride (1:1) and sodium-potassium fluoride (1:1). It is concluded that vibrational spectroscopy cannot give unambiguous information concerning the existence of complex ions in fused salt, mixtures.

Jan 1, 1963

By T. E. Masoner

The struggle to get the minerals industry seriously interested in high intensity wet magnetic separation* has been difficult. The high capital cost of the equipment, the lack of basic research, the lack of operating information, and the diverse characteristics associated with different minerals and ores have prevented the development and use of HIMS-W on a wide scale. The Climax Molybdenum Company, a Division of American Metal Climax, Inc., located at Climax, Colorado, was among the first companies in the Americas in recent years to support the development of HIMS-W to recover weakly magnetic minerals on a large scale. The Climax Molybdenum Company, one of the world's largest underground mines, processes about 40,000 tons per day of ore, from which about fifty million pounds of molybdenum disulfide are produced each year. By-products include tungsten, iron pyrite, tin, and some monazite.

Jan 1, 1968

By K. C. Kocsis

"Diesel-powered equipment has allowed the mining industry to raise production rates and significantly improve productivity, as it is rugged, mobile and reliable, but its widespread use in underground mines has generated concerns regarding the exposure of mine workers to harmful diesel engine exhaust gases and particulate components such as diesel particulate matter (DPM), which has recently been classified as a human carcinogen by the International Agency for Research on Cancer. The agency expressed further concerns that workers’ exposure to high DPM concentrations can increase the risk of cardiovascular, cardiopulmonary and respiratory illnesses. Three emerging technologies could have the ability to replace dieselpowered equipment and remove DPM from underground mines: fuel-cell-powered mining equipment, battery-powered mining equipment and advanced material handling systems. This paper reviews them and assesses whether they have reached the point where the pollutants emitted by diesel-powered equipment can be removed from underground mines through the introduction of zero-emission mining equipment and power systems. Information is also provided from the results of a feasibility study, including a detailed cost benefit analysis, carried out at six Canadian and nine U.S. underground mines, which looked at the possibility of replacing diesel-powered production equipment with fuel-cell-powered equipment. The remarkable pace at which battery technology is progressing is also reviewed, and the feasibility of replacing diesel-powered mining equipment with battery-powered equipment is assessed. IntroductionHazardous pollutants in underground mines. Why is it important to remove diesel particulate matter (DPM) from underground mines? Over the past 40 years, diesel-powered equipment has allowed the mining industry to achieve rising production rates and major improvements in productivity, as the diesel engine is an economical source of power and diesel-powered equipment is usually rugged, mobile and reliable. On the negative side, the toxicity of some diesel exhaust gases is well known (Grenier et al., 2001), and the widespread use of diesel-powered equipment in underground mines has generated increasing concerns about the occupational exposure of mine workers to harmful diesel engine exhaust gases and particulate components such as DPM. Diesel equipment also entails other hazards like heat and humidity. Exposure to excessive heat can cause heat illnesses, such as heat rash, heat exhaustion and heat stroke (Donoghue, 2004; Roghanchi et al., 2016), and a hot and humid underground environment negatively affects the efficiency of the workforce, which may result in a decline in production output (Roghanchi et al., 2017)."

Jan 10, 2017

"Mining used to be a business primarily focused on the technical aspects of getting valuable ore out of the ground and extracting the minerals efficiently. Without denying the importance of these skills, a narrow focus on technical issues is no longer enough to guarantee success when it comes to exploiting rare earth element (REE) deposits. Molycorp failed to enter the global REE market in a successful manner, while none of the many REE exploration projects has turned into an active mine so far and none is expected to commence operations in the near future. Accordingly, the world of REE is far more complex compared to other commodities. This paper looks into the REE industry to identify the factors that can connect potential U.S. REE mines to the market. The ability to break free from past thinking and become future-focused is a key driver. Mining of REE is pointless without a corresponding value-adding chain, while developing a value chain without first establishing an uninterruptible source of REE is also senseless. The mining sector must be based on the REE value chain and vice versa, along with the establishment of a market channel for the REE products that come out of the mine. INTRODUCTION It has been seven years since rare earth elements became the subjects of front-page headlines. It was when the controversial Chinese export policy for these critical commodities was epitomised in a maritime border dispute with Japan in September 2010 that resulted in the big REE crisis and price spike of 2011 (Barakos et al, 2016c; Mancheri, 2015). The world was dismayed, especially in REE-importing countries, such as the United States that was and is still totally dependent on Chinese production and exports (Barakos et al, 2016c; Kennedy, 2015). The short-lived alarm initiated a treasure hunt by way of exploration for REE deposits all over the world. The continuously growing demand on the one hand and the Chinese sovereignty of the REE-market on the other, led the rest of the world to explore their own REE resources. In just a few years, more than 400 projects were initiated to explore REE deposits outside of China (ERECON, 2015; Goodenough, 2016). The prices of REE, however, dropped rapidly and at the moment of writing this paper are in 6-year lows, at the level of the price average before the 2011 crisis (Barakos, 2017). The viability of even major established producers is being challenged, not to mention the development prospects of potential REE-market entrants (Barakos et al, 2016b; Rollat et al, 2016). Production cutbacks and industry consolidation in China impel REE market experts to forecast that prices have already reached their lowest point and have nowhere to go but up (Adamas, 2015; Roskill 2015). Yet, expectations for increased REE prices are limited and drastic changes are unlikely to happen in the near future, as there is still excess supply in the overall REE market (Barakos, 2017). Nevertheless, the low prices of rare earths are not the only reason that potential producers are struggling to enter the global REE market. Among other parameters, the separation of the individual elements seems to be the most important factor, as it is technically challenging and expensive to build and to operate."

Jan 1, 2018

By T. BACHMANN, G. SHAPLAND, E. Amini, N. BEATON, M. BECERRA

Process plant modeling in the computer environment has been developed over the past 40 years by implementing the comminution models formed by the Julius Kruttschnitt Mineral Research Centre, University of Queensland, in the early 1970s. The models for the other processes in a mine value chain, such as blast fragmentation and flotation, were continuously developed and improved in parallel as well. Other research and commercial entities have also developed process modeling methodologies in the computer environment, which evolved as specialized commercial software or through equations set up in Excel spreadsheets. These were performed on a local computer, in thousands of simulations over a long period of time due to hardware limitations and the lack of a fully automated process. This limits the application of detailed process simulations for scale-up and strategic planning analysis, as they require many simulations to cover all possible scenarios which would take a lifetime when using local computers. The Integrated Extraction Simulator (IES), as the next generation of cloud-based software package, has made it possible to run simulations on the entire operation value chain in the same platform, including drilling and blasting, crushing, grinding, flotation, and other downstream process and material-handling units. This capability has allowed IES to handle multivariable simulations across the mine value chain, including pre-concentration and in-pit size reduction, and modify the process simultaneously.