Search Documents

By Joseph D. Drew

Oregon Resources Corp. (ORC) has developed and permitted a new mining operation that incorporates a process design that will allow the unique paleo-beach placer deposits of southwestern Oregon to be extracted efficiently and economically, creating the only domestically mined source of a unique foundry grade chromite and specialty de-veining sand for precision casting. The operation will also provide an additional domestic source of garnet and zircon. Engineering design has been guided by the variable geology and mineralogy of the paleo-beach placer deposits as well as the need for a dry tailing scheme that resolves a lack of water resources at the placer locations and at the same time eliminates the need for slurry settling ponds, typical of paleo-beach placer operations in North America.

Jan 1, 2010

By A. Hammons

Automated temporary roof support (ATRS) systems have been incorporated into roof bolters since the 1970's. During roof bolting, many injuries have occurred from large pieces of draw rock falling inby the ATRS beam and tipping back into the operator's area. Other injuries have occurred due to smaller, sharp rocks falling onto the operator's hand and arm during initiation of roof bolt drilling. These injuries are attributed to weak immediate roof, sometimes called roof skin failure. Even though ATRS systems support the roof and provide a measure of protection against roof skin failure, additional hazards sometimes do exist immediately inby and outby the supported roof. Design innovations such as the ATRS mounted rocker pad deflector systems have been designed to improve the roof bolter operator safety. This paper will inform the reader of the hazards, machine evolution through different design solutions, and the current state of the art in preventing roof skin failure injuries when roof bolting.

Jan 1, 2009

By D. H. De Jager

Fluorapatite is an important constituent of the greater part of the basic and ultra-basic rock members of the Complex. The evidence for and role of primary magmatic processes in the development of concentric zones of dunite, pyroxenite, syenite and carbonatite and its consequent bearing on the distribution of apatite are discussed. The presence of at least two generations of each of the latter three rock types indicates the cyclical nature of magmatic activity. Pegmatitic-metasomatic phases corresponding to the major magmatic cycles resulted in emplacement of pegmatoidal assemblages. The abundance of apatite in the pegmatoid can be traced to the composition of its parent magma and its cooling history. Approximately 2.5 million tonnes of phosphate concentrate are produced annually from ores containing from 10 percent to 25 percent apatite.

Jan 1, 1978

By Clark Woodland, William E. Stanley

Mining companies have been required to enter a "new era of management" in the 1980's as they strive to become more efficient in an increasingly competitive market place. One response for many companies has been to modify their mine accounting systems to make them more effective for cost control and decision-making. This paper discusses some of the major issues in developing and implementing a standard costing system as part of improved management reporting and cost control procedures. It describes the key features and benefits of a computerized standard costing system with particular emphasis on budget-setting and variance analysis. It also identifies important factors to be considered in order to achieve successful project planning and Implementation.

Jan 1, 1987

By P. K. Sharma

The acidophilic and chemolithotrophic Thiobacillus ferrooxidans bacteria grown in the presence of soluble ferrous ions and solid substrates (sulfur, pyrite and chalcopyrite) as their energy source have been used in the investigations. The cell surfaces are characterised by zeta-potential, contact angle, FT-IR and FT-Raman studies. The adsorption isotherms of the cells on pyrite and chalcopyrite indicate that the adsorption begins on pyrite at a much lower equilibrium cell population than on chalcopyrite. The isotherms tend to level off at a cell adsorption density corresponding to a horizontal monolayer coverage when the geometrical dimensions of the cells are considered. In the presence of cells, the xanthate flotation of pyrite completely depressed, whereas chalcopyrite flotation is unaffected. The results suggest that chalcopyrite can be selectively floated from pyrite, also at a neutral pH region, in the presence of T. ferrooxidans cells.

Jan 1, 1999

By CHENGLONG XU, HAORAN LI, YALI FENG, JINRONG JU, Shunliang Liu

In order to realize the resource utilization of spent hydrodesulfurization catalyst, a solvent extraction-oxalic acid precipitation process is studied in this paper for efficiently recovering vanadium, nickel, and aluminum from the acid leaching solution of spent hydrodesulfurization catalyst. The process conditions for extracting vanadium with Cyanex 272 and precipitating nickel using oxalic acid as a precipitation agent were explored in detail. The results show that vanadium (IV) in the sulfuric acid medium containing nickel and aluminum was efficiently and selectively extracted by Cyanex 272. After three-stage countercurrent extraction, the extraction efficiency of vanadium was 99.76%, and the co-extraction efficiencies of nickel and aluminum were only 2.47% and 1.87%, respectively. Thermodynamic calculation shows that the extraction of vanadium (IV) from the sulfuric acid medium with Cyanex 272 is an endothermic reaction. The innovative method of oxalic acid precipitation was used to recover nickel from the raffinate, achieving selective extraction of nickel from the solution containing a high concentration of aluminum. The precipitation efficiency of nickel was 98.58%, while that of aluminum was only 0.75% under optimal conditions. The proposed flowsheet for the separation of vanadium, nickel, and aluminum from acid leaching solution may provide a new idea for the comprehensive recovery of valuable metals from spent hydrodesulfurization catalyst.

Nov 30, 2022

By Cheng Xie, Zhihu Li, Xiaoming Sun, Linsen He, Jiaxu Ding, Jinkun Yang, Yong Zhang, Zhenmin Qi

To solve the problem of large deformation of deep soft rock roadway, taking the soft rock roadway of no. 1 coal mine in New Shanghai as an engineering example, the deformation mechanism of surrounding rock of deep soft rock roadway is analyzed by combining theoretical analysis, numerical simulation and field test, and the control countermeasures centering on deep and shallow dense drilling are put forward. Through theoretical derivation, based on the masonry beam theory, surrounding rock structure S-R stability principle and composite beam principle, the length, angle, and spacing of deep and shallow dense drilling are determined. Through numerical simulation, the deformation evolution process of soft rock roadway surrounding rock after dense drilling pressure relief is reproduced, and the influence of drilling parameters (drilling spacing, dip angle) on pressure relief effect is analyzed and compared. The field application test and monitoring verify that the deformation control measures of deep and shallow dense drilling broken roof surrounding rock have a good effect of large deformation control of soft rock roadway, and provide a new support means for the safety and stability control of soft rock roadway.

Mar 2, 2024

By H. J. van Antwerpen

AngloGold Ashanti operates the world`s deepest mine, Mponeng gold mine, in South Africa. A vast refrigeration and ventilation system provides acceptable working conditions 3800m below surface at 60°C rock temperature. In such a system, optimisation and assessment of modifications becomes very difficult. With that in mind, a research project was launched to determine whether recently developed system simulation technology can be applied to a mine as vast and complex as Mponeng. Using the techniques and methods as implemented in FLOWNEX software, it was indeed proven to be possible to do a mine-wide combined simulation of compressed air flow, ventilation air psychrometry and refrigeration water systems. Interactions between the various streams included heat transfer, pressure drop, evaporation and condensation. The simulation model was used in a parametric study to test various water flow and temperature operating points for the refrigeration system. It was found that, given current limitations, the mine refrigeration system is running fairly close to optimal but with some opportunities for improvement. The simulation model also provided useful insight for future changes or extensions to the system.

Feb 23, 2014

Mineral processes are relatively simple and metallurgical accounting would also be simple if it were not for the nature of the raw materials and the large scale of operations. Essentially the balance between input and output requires only weighing and assaying of the feed, salable products, and waste. but because of complexities to be described in the following pages there are few plants that do not encounter difficulties that cause some sacrifice of precision for economy and practicality. In arriving at a sound compromise, capable

Jan 1, 1985

By Evgueni Jak

Pyrometallurgy is an important sector of modern industrial society actively participating in solving current environmental, economic, materials scarcity and other challenges. Recent advances in analytical methods, experimental techniques, thermodynamic, phase equilibria and process modelling tools provide new opportunities to increase the productivity of pyrometallurgical reactors, the treatment of complex feeds and metal recoveries. Fundamental theoretical models can now be used to make a significant next step towards the development and implementation of computerised models describing real industrial processes—Virtual Reactors, and computer-aided smart-decision-making systems that may be called Pyro-GPS by analogy to GPS; these developments can facilitate knowledge-based improvement and optimization strategies. The implementation of these improvements require ongoing collaboration between researchers, industry and government

By Randy Reed, Barbara J. Arnold

Respirable crystalline silica poses a significant health risk, with the American Lung Association estimating that 2.3 million workers are exposed to silica in the workplace. This includes mine workers as well as those in many other industries. Reducing dust formation is sometimes not possible so other methods to reduce exposure are critical. These methods include the use of surfactants to reduce airborne dust particles. However, it is the proper selection and application of surfactants that leads to reduced dust exposure. A discussion of how surfactants work, especially for silica dust, leads to guidance for surfactant selection followed by a review of technologies for their application.

Feb 1, 2024

By Bruce K. Cantrell, Stephen W. Stein, Kenneth L. Williams, David Hassel, Harvey Patashnick

In June 1992, the Mine Safety and Health Administration (MSHA) published the 'Report of the Coal Mine Respirable Dust Task Group; Review of the Program to Control Respirable Coal Mine Dust in the United States." As one of its recommendations, the report called for the accelerated development of two mine dust monitors: (1) a fixed-site monitor capable of providing continuous information on dust levels to the miner, mine operator, and to MSHA, if necessary, and (2) a personal sampling device capable of providing both a short-term personal exposure measurement as well as a full-shift measurement. In response to this recommendation, the National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Center, initiated the development of a fixed-site machine-mounted continuous respirable dust monitor. The technology chosen for monitor development is the Rupprecht and Patashnick Co., Inc. tapered element oscillating microbalance. Laboratory and in- mine tests have indicated that, with modification, this sensor can meet the humidity and vibration requirements for underground coal mine use. NIOSH is continuing that effort by developing prototypes of a continuous dust monitor based on this technology. These prototypes are being evaluated in underground coal mines as they become available. This effort, conducted as a joint venture with MSHA, is nearing completion with every promise of success. The immediate benefit of this effort will be to researchers, regulatory personnel, and mine personnel, by permitting evaluation of specific mining practices to see which expose mine workers to excessive dust levels. Using this information, mine personnel can optimize mining procedures to reduce dust exposure. MSHA and the operators will also be able to use the dust concentration data to judge whether dust plan parameters are adequate to continuously maintaining environmental dust levels below the applicable standard. The second development recommended by the Dust Task Group was a person-wearable version of the continuous dust monitor. It will be a monitoring system designed to provide a measurement of worker exposure to respirable dust, both during and at the end of the shift.

Jan 1, 1997

By Isa Nozari, Asghar Azizi

The extraction of copper from sulfate leaching liquor was investigated using Acorga M5640 commercial extractant in kerosene diluent. The effects of important factors such as the extractant concentration, contact time, liquor pH, and temperature were examined on the separation factor Cu/Fe and the extraction efficiency of copper. The results indicated that nearly 92.32% copper was extracted from the leach liquor at 10% (v/v) Acorga M5640 concentration, 1:1 aqueous/organic phase ratio, 20 min contact time, pH 2.5, and 25 °C temperature. Also, the further increase in the values determined had no positive impact on the extraction of copper. Under these conditions, the separation factor Cu/Fe was obtained about 29.64. The extraction mechanism was studied applying the plot of log(D) – 2 pH against log [extractant] and it proved the association of two moles of Acorga M5640 for the extraction of one mole of copper. McCabe–Thiele diagram was constructed and a single-step extraction process was found to obtain themaximumextraction. Additionally, thermodynamic datawere investigated and the extraction process was endothermic and non-spontaneous at 298 K (ΔH = 27.05 and ΔG = 15.52 kJ mol−1). Moreover, the loaded organic phase was stripped and 80.94% copper was recovered after 20 min using 10% sulfuric acid concentration.

Jul 31, 2020

By Wei Victor Liu, Na Zhang, Chengkai Fan, Bei Jiang

The truck haulage data from open-pit mine sites are usually massive and multidimensional with multi-peak Gaussian distributions. Artificial neural networks (ANNs) are well-known machine learning algorithms to handle massive and multidimensional data for building models. Moreover, Gaussian mixture modeling (GMM) is a suitable option for processing the data under multi-peak Gaussian distributions and improving model accuracy. For the first time, this study used a back propagation neural network (BPNN), an extreme learning machine (ELM), and a Bayesian regularized neural network (BRNN) coupled with GMM to deal with the complex truck haulage data and build three weighted ensemble models (WE-BPNN, WE-ELM, and WE-BRNN models) to predict truck productivity at mine sites. Decision tree (DT), random forest (RF), gradient boosting machine (GBM), and extreme gradient boosting (XGBoost) were used to build models to be compared with the weighted ensemble models. The results showed that the WE-BRNN had a higher accuracy than the WE-BPNN and WE-ELM models. The proposed weighted ensemble models performed better than the benchmark models in predicting truck productivity, indicating that a weighted ensemble approach based on the GMM analysis significantly improved the model accuracy. Based on the relative importance analysis, haul distance was the most crucial input variable for predicting truck productivity. This study provides a new approach to predicting truck productivity, which will help mining companies make sound budget decisions and improve mine planning.

Mar 2, 2023

By H. Sevim

An innovative approach in designing the haulage systems for underground coal mines is discussed in this paper. The haulage systems are formed by serially connected components. Therefore an economic and efficient design of the entire system is necessary. The computer model that uses a heuristic algorithm solves this design problem globally in a single run. It is a probabilistic model because it considers the probabilistic aspects of face operations. It is versatile because it can accommodate any type of mining and belt conveyor network configuration. The hoisting section can be used to design drum or friction hoisting systems for single or multiple level operations. These systems can have two skips in balance or a skip and a counterweight in balance. The model also has the option to internally determine the capacity of bunker(s) and shaft-bottom bin. The objective is to minimize the expected cost per ton of coal hauled from the coal faces to the surface. At the end of the paper is an example that illustrated the capabilities of the model.

Jan 1, 1987

By A. A. Zatout, G. H. Sedahmed, T. M. Zewail, M. H. Abdel-Aziz, B. S. Ibrahim, E-S. Z. El-Ashtoukhy

In this work, the possibility of intensifying the cementation process in stirred vessels was studied by using the perforated baffles as turbulence promoters; the cementation reaction of Cu+2 on Zn was selected as a model. Zn was used in the form of a sheet lining the inner wall of an agitated vessel. Parameters considered are initial concentration of Cu+2, solution temperature, impeller rotation speed, and impeller geometry. Within the present range of parameters studied, the rate of cementation was found to increase with increasing initial concentration of Cu+2, solution temperature, and impeller rotation speed. At the same rotational speed, a flat turbine gave a higher rate of cementation than a 45° pitched turbine. The present suggested that baffles’ geometry gave superior performance in terms of mass transfer of copper cementation compared to the conventional baffle geometry. All parameters that affect the rate of cementation were correlated in the form of dimensionless equations suitable for the design and performance prediction of the agitated vessel. Potential applications of the obtained results in the field of hydrometallurgical processes and wastewater treatment were discussed.

Jan 12, 2021

By J. Ke

Traditional geostatistical methods have been used in ore reserve estimation for decades. Neural Networks (NNs) have provided an alternative approach to data analysis and ore reserve estimation. Unlike the traditional geostatistical methods, neural network uses a highly non-linear complex algorithm to do the estimation. Although Neural Networks have been demonstrated to be attractive alternatives as with every new techniques, there are questions which remain unanswered. This paper presents a comparative analysis with different types of metamodeling approaches -- Triangular, Kriging, Spline, and Neural Network. The neural-network is organized in a multiple-layers and Back-propagation model is used to handle the non-linearity and hidden slabs for smoothing the predicted results. With multiple dimensional and very noisy drill hole sample data, the ore grade is predicted and the overall performance is validated by the analysis of R-squared (R2), Root-Mean-Squared (RMS), and contours of ore grade spatial variability. The ore grade and tonnage of estimated outputs are also compared with various cut-off grades.

Jan 1, 2003

By C. J. Bise, M. F. Sindelar

Regulations, such as the MINER Act of 2006, require the installation of redundant and secondary communication systems to assure that contact can be established with coal miners who may become trapped underground as a result of an event such as a fire, explosion or inundation. For half a century, the orientation towards underground communications has been that more complex systems better serve the coal miner. However, if a goal is to provide for an alternative means of establishing communication between the surface and trapped miners underground, then some of the technology employed should be simple, reliable and cost-effective. Coal mines spend hundreds of thousands of dollars on exploratory drillholes to characterize reserves, sometimes decades ahead of mine development. During the pre-mine planning phases, certain exploratory drillholes could be located and then outfitted with a simple communication link that would remain compatible with the continuing evolution of communication systems. Inexpensive links, whose locations would be accurately recorded, would be exposed by continuous miners during mine entry development, thereby allowing an underground phone to be connected to a surface station in the event of an emergency. A latent network of these communication links could be installed for less than $500 each, minimally affecting drilling and grouting operations, and could be designed to be compatible with many communication devices. This research examines methods and materials for incorporating an embedded communication link during pre-mine exploration drilling, addresses significant factors affecting its implementation, and presents a recommended design. Since mine plans are known to change, the objective is to minimize cost so that, if not used, the investment is minimal for a potential secondary means of communication between the surface and underground workings.

Jan 1, 2014

By Fei Chen, Xun Xu, Dezhong Kong, Yu Xiong

We address the problem of rib spalling caused by mining-induced roof movement. This problem affects production and safety of the working face. We address this problem by using the 3DEC numerical software to simulate the distribution and evolution regularity of displacement, stress, and the extent of plastic zone in the overlying strata and coal face during the advancing excavation of the 10,905 working face of the mine. Results showed that the first weighting interval of the 10,905 working face is 50 m, and the periodic weighting interval is 20 m. The fractures of overlying strata develop during the first weighting; the vertical stress and vertical displacement of the main roof increase by 45% and 10%, respectively; the vertical stress of the coal face increases by 11%; and the plastic zone in front of the working face increases rapidly. The displacement and stress of the main roof and coal face change periodically during the period of periodic weighting. The variation range during the periodic weighting is less than 30%, but the overall degree is larger than that before the first weighting. Finally, the integrity and rationality of numerical simulation are supplemented and verified by similarity simulation. On this basis, the proposed roof and coal face stability control scheme reduces the maximum horizontal displacement of the coal face from 16 to 4 cm, that is, a decrease of 75%. This study provides theoretical guidance for roof support and coal face stability control of working faces under similar conditions.

Dec 26, 2022

By J. H. van Laar, C. S. L. Schutte, M. Le Roux

Highly energy-intensive systems prone to wastage are significant causes of unnecessary energy losses in industry. Deep-level mine chilled water reticulation systems fall within this category of inefficient energy-intensive systems. Some techniques (measured baselining, zero-waste baselining, leak detection, and control valves) exist to identify and reduce wastage in mine water reticulation systems. However, these techniques have not been compared, which begs the question of which is more accurate. A need, therefore, exists to compare these methods to determine the effectiveness of each. This study investigates each method and applies them to a case study mine, providing a platform for comparison. These methods identified wastage ranging between 2 and 20 l/s (3–30% of water consumption). The comparative effectiveness of the methods from best to worst was found to be zero-waste baselining, leak detection, control valves, then measure baselining. This study proposes an application procedure combining the considered methods to identify and eliminate wastage on deep-level mine systems more efficiently.

Jan 31, 2024