Search Documents

By Eugen Gluck, Gus Van Weert, Peter Kondos

"Microwaves have the capability to heat up sulphides, especially clusters of particles of approx. 1 mm. Some sulphides absorb microwaves more readily than others. Molybdenite is especially effective in this regard, possibly due to its flaky nature and/or electrical conductivity. Even where it occurs in low concentrations in a deposit, individual rocks may be ore grade due to the high monetary value of MoS2. Such rocks often result from crushing mined veinlets or stockwork, or are contained in the cutoff grade fraction of ROM. Machine segregation of rocks high in MoS2 by infrared sensors after microwaving could therefore advantageously be used to upgrade lower grade ore between Mine and Mill. This would reduce the size of the latter, and thus its CAPEX and OPEX. Such upgrading could also yield shipping ore for a distant Mill, or extend ore reserves.Barrick Gold Corp. has been supporting the development of MW/IR sulphide sorting for the past three years. The results of MW/IR sorting work on molybdenite and other (pyritic) ore samples from a variety of sources are being presented here.INTRODUCTIONThis paper looks at mechanized, i.e. machine ore sorting technologies currently available and under development, and what conditions would be needed for the potential application of such ore sorting to sulphide mining and milling. Current machine sorting involves no-contact sensing technology for rocks, and signal processing after sensing to activate airblast segregation of certain rocks, normally the smallest mass to keep compressed air costs down.The forerunner of modern sorting is probably magnetic separation, which utilizes an inherent property of certain ores to divert it into mag and non-mags fractions. Radiometric ore sorters, which have been applied successfully for decades in the pre-concentration of uranium ores (Wotruba and Riedel, 2006) initiated modern sorting. In the 90’s, sensor-based machine sorting became a viable means of increasing the overall economic recovery of a resource. This technology became driven by the availability of low cost computing equipment and the concurrent development of algorithms, and by the availability of extremely fast response sensors and air actuators, allowing the sorting equipment to run faster, dropping the cost per tonne. It has been in industrial minerals processing that rock sorting has been most widely adopted, not really surprising. Liberation occurs on a different scale than in the base metal industry. Most industrial minerals are mined from massive deposits, requiring (in the past) no upgrading. Many of these operations now run into product contamination problems, which ore sorting can solve. One illustration: in Finland, a quarry is separating limestone from dolomite at 500 tonnes / hour, with individual rocks weighing up to 15 kg. Many of these industrial minerals operations have stockpiles of earlier discarded below-quality rocks, now being reprocessed with the help of ore sorting. The economics of this are very favourable, going from zero or negative value (stockpiles can not be left when closing the mine) to full product value for at least a portion of the stockpile. This suggests that in the future the economics of overburden sorting could become attractive under the right circumstances and such treatment could well become an integral part of open pit mine development."

Jan 1, 2009

Background Chronology 2008 Positions May 8, 2010 Summit Going Forward Say one thing and do another ??Genuine passion to see our customers succeed?, ?A passion for exceeding our customer?s expectations? Self serving actions to gain competitive advantage at the expense of the customer No single supplier or technology can manage the overall mine and its integrated operation - April 2005: Informal meeting at Toronto CIM 2004 -Unanimous interest - July 2005: Formal Calgary Meeting, developed: - Scope and vision statement , - OEM/OTM communication plan, - industry communication plan - Aug?Nov 2005: Aligned with SMART - Nov 2005?May 2006: Direct OEM, OTM communication - May ?Sept 2006: Developed baseline standards - Sept -April 2007: Developed SMART document - Sept 2007: Document distribution and request OEM OTM response - Jan ?May 2008: Acquired OEM OTM feedback and positions May 2008: Results presented to SMART and discussions on next steps

May 1, 2010

By Chris Fleming, John R. Goode, James Brown

"Data will be produced from two uranium feasibility studies that were conducted in 2008, both involving uranium recovery from leached slurry by resin-in-pulp (RIP) with strong base resins. Excellent metallurgical results were produced in RIP pilot plants in both studies, and the loaded resins were eluted with strong sulphuric acid and recycled to RIP in an integrated process. Resin losses by either abrasion or mechanical breakage were immeasurably low.Metallurgical results from these two campaigns will be presented, along with an economic analysis of RIP versus the alternative process of CCD or filtration and solvent extraction.INTRODUCTIONThe recovery of uranium directly from pulp with strong base resins in RIP contactors was practiced commercially in the USA in the 1960s, but the process never established itself as a viable alternative to solid/liquid separation and solvent extraction. This was due mainly to the necessity to do a sand-slime separation partially resulting from the unavailability of coarse resin beads, inadequacies in the design of the RIP contactors and screens to separate resin from pulp, as well as problems with the strength and durability of resins in agitated pulps.There have been significant advances in the last 30 years in each of these areas. All the commercial resin manufacturers are now producing very tough, durable, strong base resins, and are manufacturing them in a large bead size that is better suited to RIP applications. In addition, with the emergence and wide spread implementation of the carbon in pulp process in the gold industry in the 1980s, many innovative techniques for preparing leached slurries and separating carbon from pulp have become firmly established. These techniques have proven to be equally applicable to resin separation from pulps in RIP contactors."

Jan 1, 2010

By S. Rajeswari, D. Gopi

"Pitting corrosion inhibition of 304 stainless steel (SS) in groundwater with a ternary inhibitor mixture (phosphonic acid + bivalent cation + various surfactants) was studied with different environmental variables such as temperature, pH, dissolved oxygen and chloride ions. Critical pitting potential and corrosion potential were calculated for these test media using electrochemical techniques. Under the tested condition, the localized corrosion resistance of 304 SS was determined and the results are discussed. IntroductionPitting corrosion of metals and alloys is a major cause of failure in chemical processing desalination plants, scrubber for flue gas desulphurization (FGD) plants, water storage tanks and pipelines, petroleum refineries, etc.Heat exchangers and condensers in inland thermal and nuclear powerplants utilize groundwater as a coolant, but materials of construction are generally prone to localized corrosion.Localized corrosion attack can be initiated when the passive film on the metal is disrupted. The presence of certain aggressive anions such as chlorides (Cl-) can migrate to the actively corroding area and stabilize pitting corrosion. Attention has been focussed on improving the resistance of stainless steel against localizedcorrosion in aqueous environments.One of the most accepted methods of avoiding corrosion is by the addition of chemicals (inhibitors). Over the past two decades, some phosphonic acids have been explored due to their good corrosion inhibition efficiency and low toxicity (Fang et al., 1993; Karman et al., 1998; Rajendran et al., 1998; Gopi and Rajeswari, 2000a). Bivalent cations like Zn2+ are often applied as additives to inhibit the metal dissolution (Sekine and Hirakawa, 1986; Aruna Bahadur, 1998)."

Jan 1, 2003

"The characterisation of resources and description of variability across different ore domains is key to accurate prediction of probable metallurgical performance. Such characterisation testwork often has limited drill-core from which to work and this immediately confines the characterisation method to smallscale. For flotation feeds, the JKMSI (Mineral Separability Indicator) is being developed as a potential characterisation tool, building on earlier work by Chudacek, (1990), which used shaken test tubes, and was called the EMDEE device. In addition, the consistency of flotation recovery for specified size fractions has shown to be preserved, irrespective of the amount of material in that size fraction obtained by different milling conditions, so that the overall recovery can be estimated from knowing the particle size distribution (McIvor and Finch, 1991; Bazin et al, 1994, Runge, 2007 and Wightman et al, 2010) The JKMSI unit uses less than 10 g of material per test in narrowly sized classes and results to date have demonstrated the value of the test. This paper discusses the potential of the test by demonstrating the link between JKMSI performance and mineralogy of five different ores from Laguna Seca, Escondida Minera Limitada as well as the correlation to plant scale performance obtained in an earlier survey (Coleman et al, 2006). Further work to tie down the proof of representatively of the small sample has been identified and is discussed and included in the paper. INTRODUCTIONSince the uptake of the flotation process at the turn of the twentieth century, small scale, laboratory methods have been sought to characterise flotation response. Although laboratory batch flotation tests are the most widely used method to evaluate reagents, characterise ore variability and obtain suitable model parameters using various scale up factors Runge (2101) other methods using less ore would be useful where ore samples were limited.A method using test tubes for testing ores’s flotation response to reagents was first developed by Ian Walk (Wark & Wark, 1935; Wark; 1938; Sutherland and Wark 1955). In these tests a 50 cc stoppered measuring cylinder served as a means for a qualitative experiment, the aeration being effected through violent shaking by hand. In these experiments about 10 g of mineral was ground by pestle and mortar under water after which the ground material was deslimed and adequately conditioned with the appropriate reagents."

Jan 1, 2013

By S. R. Amos, N. O. Lotter, A. L. Hannaford, J. F. Oliveira, D. W. Broughton

"Ivanplats Ltd appointed Xstrata Process Support to perform the flowsheeting development work for their hypogene and supergene geomet units of the Kamoa Copper deposit, located in the Democratic Republic of the Congo. Through systematic flowsheet development using modern Process Mineralogy, the optimised milestone flowsheet delivered a saleable concentrate grade of 32.8% Cu at 85.4% recovery with hypogene ore, and a saleable concentrate grade of 45.1% Cu at a recovery of 83.4% for supergene ore. The significant value of this development is that a single flowsheet will treat both hypogene and supergene ores and produce saleable concentrates. Further work to advance the flowsheet performance has been identified for investigation in the near future.INTRODUCTIONLocation and Description of the Kamoa DepositThe Kamoa copper resource is located some 40 km west of the city of Kolwezi, in the south west of the Katanga Province of the Democratic Republic of the Congo, in the region of Central Africa. Drilling at Kamoa in 2008-2009 had discovered laterally continuous, sediment-hosted, high-grade stratiform copper mineralisation in a newly discovered copper district that forms a previously unrecognised western extension of the famous Central African Copperbelt – which hosts such world-class deposits as Kolwezi, Tenke-Fungurume, Konkola and Nchanga. This discovery showed that the western end of the Copperbelt in the Congo does not terminate at Kolwezi (Friedland & Broughton, 2009). The resource contains hypogene and supergene geomet units with a transitional zone located inbetween the (upper) supergene and the (lower) hypogene. In the hypogene unit, the major copper sulphides are bornite, chalcopyrite and chalcocite, whilst in the supergene, the sequence is led by chalcocite, then bornite, and finally chalcopyrite. Covellite is present in both units as a minor copper sulphide. Both geomet units will be mined and treated in one concentrator, either as blends or as campaigns."

Jan 1, 2013

By V. K. Gupta

"Effect of mill speed on grinding kinetics has been investigated with a view to using mill speed as a manipulated variable for control and optimization of the grinding circuit performance under variable ore hardness conditions. Dry and wet batch grinding tests were carried out for quartz, limestone and cement clinker in a 29 cm x 18 cm laboratory ball mill. Mill speed values selected were 55 and 70% critical. In the case of dry grinding operation, with an exception of quartz, for all materials studied the effect of mill speed on grinding rate was found to be insignificant for sizes finer than about 35 mesh. In the case of wet operation, grinding rates were found to be approximately proportional to the mill speed. The implications of these results are discussed.INTRODUCTIONIt is well known that mill speed has a considerable effect on the grinding rate of the ore particles l-3 For particles of a given size there is an optimum speed at which mill grinding efficiency is maximum (i.e. specific energy consumption is minimum) 3•4. Mill speed can, therefore, be effectively used as a manipulated variable to deal with the disturbances arising from changes in the size and hardness (grinding rate) of the ore being fed to the grinding circuit. Though, it has not been the case so far, with recent developments of ring motors2 and frequency inverters5 a continuous variation of mill speed has now become feasible, and it is expected that mill speed control will soon be a regular feature of plant operation2,6."

Jan 1, 1985

By H. Ewaschuk

"INTRODUCTIONRio Algom's Stanleigh Mill in Elliot Lake began production in June of 1983. The highly instrumented mill treats uranium ore at an average rate of 3900 metric tons per day. To help ensure a good start-up and low operating costs, an extensive training program was undertaken prior to and during start-up. This presentation describes how an unconventional operating crew were combined to form an operating unit with a high efficiency in terms of production and labour utilization. I would like to point out at the outset that the operating philosophy, and the role of the supervisors and the operators as set up at Stanleigh is not unique. Indeed, I have seen the same results at a couple of small plants where efficiency meant survival. However, these situations appeared to be the exception, and it was not readily apparent how similar results could be obtained in a larger plant. A factor that existed at the time was low labour turnover. As in most parts of Canada, jobs were easy to get in the Elliot Lake camp in the late 1970's. This, and other factors, contributed to an unusually high labour turnover. This changed dramatically in the early 1980's. Indeed, Rio's two other operating mills, Quirke and Panel reduced crew sizes at this time to reduce operating costs. As a result all of Stanleigh's operators came from Quirke and Panel with experience varying from 4 to 7 years. The experience that operators had was obviously of benefit and served to reduce the scope of the training program from what would have been required with inexperienced personnel."

Jan 1, 1985

By L. S. Urbanoski

This presentation describes a major modernization project at the Geco concentrator. The objectives of the program were to replace obsolete flotation equipment and upgrade process controls.Noranda Minerals Inc. — Gecc Division is located at Manitouwadge in Northern Ontario. The community is situated north of Lake Superior approximately equidistant from Thunder Bay and Sault Ste. Marie.Milling operations began in September, 1957. The mill processes a complex base metal ore by differential flotation techniques to produce copper, lead and zinc concentrates. To date some 43 million tons have been milled, qualifying Geco as a rather major base metal deposit.II. BACKGROUND:The Geco concentrator was designed and constructed in the mid 50's. A number of features specific to a concentrator of that vintage provided the justification for the modernization efforts described herein.Firstly, the mill was constructed without any instrumentation, not even pneumatic controls. Solid state electronics, computers and related instrumentation were unheard of, or rather primitive by today's standards.Secondly, some of the major equipment, in particular the flotation equipment, did not compare favourably to that in use today. MacIntosh flotation machines (more commonly known as Mac cells) were installed at Geco. These cells were prevalent in a number of concentrators built by Noranda, including Quemont Mining Corporation Limited, Gaspe Copper Mines Limited and Noranda — Horne Division. The Mac cells were used for copper and zinc rougher and scavenger operations. Some units were also installed for a pyrite recovery circuit that was never operated. In total, 104 Mac cells were installed in the main flotation area of the concentrator.

Jan 1, 1987

"The Detour Lake Mine is located in northeastern, Ontario, approximately 300 kilometres northest of Timmins and 185 kilometres by road northeast of Cochrane. The mill processes a free milling gold ore using both gravity circuit and leaching with a state-of-the-art carbon-in-pulp circuit. The grinding circuit is a conventional SABC circuit with a tonnage of 55,000 mtpd at 95 microns with the addition of pre-crushing upstream of the SAG mill.The present paper will describe the methodology used to successfully prove that gold of the Detour Lake Mine ore is mostly concentrated into the fine size fraction of the blasted rocks. It will describe the various options possible to create value from this ore property.IntroductionThe purpose of this test work was to determine the grade of the pebbles and consider if there was value into discarding the pebbles and replacing the material by fresh feed.1. Pebble samplingThe pebbles were sampled and assayed for grade every day for 3 months. After 3 months of sampling, the results showed that the pebbles only carried 28% of the fresh feed grade. This phenomenon can possibly be explained by the fact the gold is located into area of fracture in the rocks.January-March 2014 – Pebble assay average• Line #1 = 0.222 g. Au/t• Line#2 = 0.275 g. Au/t• Head grade = 0.88 g. Au/t2. Crushing and grinding circuit surveysWith the above information, a grinding circuit survey was planned. The purpose of the survey was to build a JKSIMMET model of the grinding circuit for mill optimization but also to understand the deportment of gold into various size fractions that may explain why there is so little gold in the pebbles. All streams and size fractions was analysed for particle size analysis and for gold.Since Detour has dual grinding lines, both circuits were sample at the end of May. Two supplemental survey of the secondary crushers were also done and a survey of the gyratory crusher."

Jan 1, 2016

By Jack J. Ayotte, Michael R. Nadon

"Today's demand for better and more efficient methods inspires new approaches to construction and mine development.A project at Asarco's Aquarius Mine provided a challenge that resulted in the adaptation of a civil construction technique to a mining application.This paper describes the construction of an escapeway shaft to surface from the mine's 150m level. The prime consideration was to provide the most cost-effective method of establishing a shaft collar in the 145 ft (44 m) of water-bearing overburden. This problem was resolved with the employment of the drilled in-caisson method.The remainder of the 500ft (152m) deep shaft was raise bored and portable hoisting equipment was used to install a permanentmanway and shaft liner.IntroductionHaving completed the first phase of exploration development in 1982, J.S. Redpath Limited was engaged to carry out an engineering and cost study to investigate the feasibility of re-opening Asarco's Aquarius Mine near Timmins, Ontario. The scheme was to develop the proven ore reserves and proceed with shrinkage stoping while carrying out further exploration development and diamond drilling.One significant and costly component of the project was the provision of an escapeway shaft to supply additional ventilation as well as a second means of egress from the mine. The major complication to this task was the presence of 145 ft (44 m) of water-bearing overburden at the site. The first and obvious approach was to use conventional ground-freezing methods as had been employed previously on .this property for the initial development shaft. This being the only ""sure"" method available at the time of the budget estimate, it was used as a basis for the study but its considerable projected cost and time demand inspired further investigation into other possible solutions.After considerable research and several brainstorming sessions, a Redpath team came up with an approach whose basic procedures had been used extensively in the civil construction field, although they were novel to the mining industry."

Jan 1, 1987

By Jonas Olsson

"The picture of China as an antiquated continent is changing rapidly and fast-forwarding progress is a fact in most infrastructural fields. Mining is not an exception. China is today the largest producer of aluminum, coal, steel, zinc, tin, lead and manganese and the country’s mineral resources comprising approximately 12% of the global reserves ranks them number three in the world after US and Russia.In order to feed the growth industry is needed to take extra ordinary strides to improve supply of raw material and Chinese mines are continuously being upgraded with the latest western technology to meet the increasing domestic demand of base metals.In Anshan located in China’s northeast province Liaoning we find one of the fastest developing mining companies, Angang Iron & Steel Group Co. Ltd. With their six mines that together process approximately 60 M ton iron ore/year Angang Iron & Steel Group Co. Ltd is the largest iron ore company in China. The group’s thorough pre-studies and technical evaluations over the past five years have made them very successful in both plant upgrades of existing operations and green field projects.INTRODUCTIONWe live in a time when the world market is gradually acclimatising to the global consequences of “The China effect”. An effect caused by a formerly sleeping giant nation that during the last years has awakened and developed beyond comparison, primarily because of booming infrastructure projects and demand for capital and consumer goods"

Jan 1, 2006

By G. A. Kosick, G. S. Dobby, O. Matwijenko

"A 100 kg/hr portable flotation pilot plant has been operated at Kidd Creek Mines with the objectives of:(a) determining performance expected by column flotation circuits on primary zinc and copper cleaning, and (b) evaluating column flotation circuit configurations.The self-supporting pilot plant, owned by Minnovex Technologies Inc. and operated by Minnovex and the University of Toronto, consisted of three 16 cm diameter by 6.5 m high columns and a bank of four Denver No. 7 cells. It was configurable to any arrangement using these four (or fewer) units. The columns were controlled through the use of multiple pressure transducer measurements. This paper presents the approach to testing and the results of more than 70 circuit tests. INTRODUCTIONThe integration and retrofitting of flotation columns within existing mechanical cell flotation circuits is becoming a common occurrence. The correct approach to this integration, however, is often difficult to define, due to a scarcity of previous experience and the difficulty in predicting column circuit performance. In most cases, the effect of column implementation has been experimentally assessed using a single pilot column, with the consequence that selection of an appropriate circuit to implement is difficult. Important considerations are the impact that column water addition will have on the existing operations, and the differences between mechanical cell and column performance in integrated cleaning circuits.To address the problem of circuit selection a portable flotation pilot plant, consisting of both columns and mechanical cells, was designed and constructed by Minnovex Technologies. The pilot plant was structured for complete flexibility of circuit configuration, with the intent to provide a means by which both research and plant personnel could determine the best possible column circuit configuration for a given application."

Jan 1, 1990

By A. M. Hill

"This is an account of the expansion of Texasgulf's Timmins concentrator by the building of a fourth circuit.The original capacity of the mine and concentrator was 3.6 million tons per year of ore. In 1974, Texasgulf decided to increase that capacity by about one third to 4.8 million tons per year. It was planned that the increased capacity would be available by mid-1978.The expansion involved work at the rninesite, increased railroad capacity, and a new circuit in the concentrator, and it is the concentrator expansion which is described here.In 1974, the minesite drew its ore from the open pit. The pit was being phased out and was to be replaced by No. 1 mine. To allow for the expansion, a second mine was required. The railroad was capable of handling 18 car trains. Its capacity had to be increased to 27 cars per train and this, in turn, required two new locomotives. Each of these alone cost half a million dollars.The concentrator building in 1974 contained the concentrating equipment and miscellaneous services (such as machine shop, warehouse, analytical lab). The grinding and flotation sections were divided into three circuits ('A', 'B', & 'C'). 'A' and 'B' circuits treated copper-zinc ore and 'C' circuit treated the much more difficult copperzinc- lead ore. This 'C' circuit had been modified over the years to implement improvements in the metallurgy."

Jan 1, 1979

By Adam Wright

"Les Mines Selbaie have been producing copper and zinc concentrates from the A-1 ore zone since 1986. This paper reviews major developments in flotation practice over that period. Firstly, ore blending strategies for Selbaie's non-homogeneous polymetallic ore are discussed. The evolution of reagent use is then reviewed, focussing on copper collector trials. A description of Selbaie's flotation columns follows. Finally, past and future developments for process control are outlined.Depuis 1986, Les Mines Selbaie produisent du concentré de cuivre et de zinc provenant de la zone A-1. Cette conférence présente !es développements majeurs en flottation qui ont eu lieu depuis ce temps. Premièrement, la stratégie du mélange de minerai non homogène polymétallique est présentée. L'évolution des réactifs utilises est démontrée, particulièrement !es collecteurs de cuivre. Par la suite !es colonnes de flottation sont presénteés et finalement !es développements futurs ainsi que ceux qui ont eu lieu dans le contrille de procédé sont expliqués.1.0 INTRODUCTIONLes Mines Selbaie, wholly owned by Billiton Metals Canada Inc., is currently mining and processing ore from a polymetallic surface deposit located 288 km northwest of Val D'or, Quebec (fig. 1). The mine produces copper concentrates containing gold and silver as well as zinc concentrates containing silver. 8000 dmt/day of ore is crushed and ground to 80% passing 49 µm, prior to processing by conventional copper/zinc differential flotation. The flotation circuits consist of both conventional and column cells (fig. 2). Detailed descriptions of the mill are available elsewhere in the literature (8,9)."

Jan 1, 1995

By Jan E. Nesset, Phillip J. Mackey

"Studies have shown that there is a correlation between commissioning and start-up time, i.e. time to reach full plant design capacity, and the degree of innovation and technical/engineering uncertainty in the project design. The paper describes the types of start-up curves for plants according to the level of technology or uncertainty in the process design. The need to properly describe and understand the commissioning and start-up time is examined using these curves and the importance on project success is highlighted. A number of case histories of recent mining and metallurgical projects are also reviewed. Finally, the paper reviews how to better assess the level of start-up uncertainty associated with a project and makes suggestions for decreasing the commissioning time due to technological risk.INTRODUCTIOThe start-up of a new mining and metallurgical facility, a much anticipated event, is a critical step in the life of such a project. Achieving a successful start-up and reaching the design capacity on-time requires careful planning, a thorough understanding of the key technological and engineering components involved and a well-trained and adequatelystaffed start-up crew. In this paper, some of the aspects related to start-up of a mining/metallurgical project will be explored, and in particular, the impact of the technology component will be examined. In order to illustrate this, a number of case histories based on recent mining and metallurgical projects will be discussed. Ways of assessing and understanding the uncertainty associated with technological issues related to start-up of a mining and metallurgical plant will also be examined.The history on mining and metallurgy is full of success stories of great mines and mills that are now considered “company makers” (well known examples of such successes include the Horne mine for Noranda which had a 1 year start-up in 1926-27, the Dome mine for Placer Dome, the Grasberg deposit for FMI in Indonesia). Less well documented are specific studies relating to plant start-ups and what constitutes a success or a failure, however there are a few notable references in the literature and these will be reviewed."

Jan 1, 2003

By A. Vien, B. C. Flintoff, R. P. Edwards

"This paper provides a critical review of the development and application of advanced controls in mineral processing at the industrial level. These algorithms can be sub-divided into four broad categories: Kalman filter, self-tuning, extended horizon, and knowledge based or expert systems. Applications from each category are described outlining the benefits derived, the relative advantages of that particular controller, and potential limitations of the controller which may inhibit their more widespread application. The paper will conclude with a description of control algorithms which are currently in the rudimentary design stage, but may hold tremendous potential for mineral processing control systems in the next decade. INTRODUCTIONThe Canadian mining industry has a large installed milling base and many plants are run with manual or low level automatic process control. The competitive pressures imposed by the market will not allow these operations to ignore the significant increase in efficiency that can be achieved through the effective application of advanced process control. These improvements will come in the form of better quality, higher productivity and reduced costs.There have been quite a number of reports of successful applications of advanced control in mineral processing applications. As this trend continues, and more of the work is documented, the technology will be more effectively transferred to process and control engineers. It is the authors' opinion that the most difficult problems facing process control are not really technical in nature. Rather, they lie more in process control education. This extends from management, through engineering to the operators.The purpose of this paper is to provide a tutorial type overview of some of the more frequently encountered advanced control algorithms. The assumption is that the reader has a superficial knowledge of this technology. In the discussions which follow, several techniques are explored within the framework of simple process examples. Industrial examples are cited for each and an evaluation of the expected longer term potential is given."

Jan 1, 1992

By Ken Dyck Sr.

"Construction of the Cigar Lake uranium mine in northern Saskatchewan is well under way. Production is anticipated to begin in the first half of 2007. When in full production, the mine is projected to produce a net 18,000,000 pounds of U3O8 per annum from a high grade ore averaging approximately 20% U3O8.Water management was a major issue that required substantial effort in the Cigar Lake design. Not only is effluent quality controlled, a tight water balance to minimize effluent volume is also designed into processes in order to minimize environmental impact. This paper focuses on the water treatment process and water handling equipment, as well as the operating philosophies that will reduce fresh water consumption to a minimum. An overview of the mining and ore handling systems, as well as aspects of controlling water production from the ore formation and the mine development areas will also be discussed.INTRODUCTIONThe Cigar Lake ore body has proven and probable reserves that total 232 million pounds U3O8. Cigar Lake is the world’s largest undeveloped high-grade deposit. It is the second largest highgrade deposit surpassed only by the McArthur River deposit another Cameco - operated mine in the Saskatchewan Athabasca Basin. Cigar Lake is owned 50% by Cameco Corporation, 37% by AREVA (COGEMA Resources Inc.), 8% by Idemitsu Uranium Exploration Canada Ltd. and 5% by TEPCO Resources Inc. When production starts in 2007, ground ore slurry from Cigar Lake will be shipped to the McClean Lake mill (owned by AREVA) some 80 km away. All of the Cigar Lake uranium will be leached from the ore at McClean Lake. During initial production ramp up, all uranium will be processed at McClean Lake to yellow cake (uranium oxide). After the average production has exceeded a 10 million pound per year rate, Cigar Lake uranium will begin to flow from the McClean Lake Mill to the Rabbit Lake Mill. At this point, subject to regulatory approval, 57% of the Cigar Lake uranium, in a uranium rich solution, will be transported to Rabbit Lake mill (owned by Cameco) for purification to yellow cake. A complete summary of the flow of uranium from the Cigar Lake ore body through to product at both McClean Lake and Rabbit Lake can be found in a recent paper titled “The Cigar Lake Project – Mining, Ore Handling and Milling” in the March 2004 issue of the CIM Bulletin. The paper was written by C.R. Edwards."

Jan 1, 2006

By Q. Zhang

The necessary capability of the gravity transportation pipeline system for cemented coal gangue backfilling at the Suncun Coal Mine, China, is about 74.4 m3?h-1 according to mining production and working times in the mine. It is estimated that the working velocity and maximum pipe length-backfill depth ratio of the backfill system are 3.82m?s-1 and 5.4, respectively and that the probable backfill capability of the system is 110.18m3?h-1. Results of hydraulic calculations for the backfill transportation system show that the designed backfill system is reliable in flowability and sufficient for backfill capability needs.

May 1, 2007

By James R. Lang

The Xietongmen deposit is located 350 km west of Lhasa, Tibet. It is a new, high-grade porphyry copper-gold discovery and the first deposit to be systematically explored by a western company in southern Tibet. In 2005, Continental Minerals Corporation drilled 21,332 m of core in 63 holes and demonstrated excellent lateral and vertical continuity of high-grade copper-gold mineralization over an area 750 m by up to 350 m in size which remains open in all lateral directions. Drill intersections repeatedly yield grades >1% Cu equivalent (based on gold and copper prices) and include 308.5 m at 0.87% Cu and 1.25 g/T Au (1.60 CuEQ%), and 315.6 metres at 0.61% Cu and 1.11 g/T Au (1.26 CuEQ%). Extensive drilling in 2006 will expand and delineate the deposit, and metallurgical, engineering, environmental and socio-economic evaluations will begin. Xietongmen is hosted by volcanic and intrusive rocks of the Gangdese belt, a magmatic arc active between 120 and 30 Ma along the southern margin of Eurasia. Pervasive alteration is dominated by a well-mineralized K-feldspar and biotite assemblage, and by a more peripheral sericitic assemblage also with strong chalcopyrite. Major vein stages include chalcopyrite-bearing quartz, biotite, magnetite and pyrite-pyrrhotite types.

May 1, 2006