Search Documents

By Alexandre Desbarats, Michel David

"All optimum pit design studies start from the geological are reserves inventory, the estimated grades of all blocks of potential are within the interpreted limits of the deposit. The actual optimization procedure is then carried out on block valuations based on these estimated grades. Thus, the relevance of any pit design can be seen to depend directly on the ore reserve estimation . To insure a proper pit design, a first step would be to use a geostatistical reserve estimation technique such as kriging, however, this is not enough. A frequently neglected fact is that the blocks of ore estimated during the planning stage of the mine are usually considerably larger than those on which the ore-waste selection will be made at the time of mining. Experience in the exploitation of large low-grade deposits has shown that large blocks, estimated to be are, when mined selectively in smaller blocks, often yield significant amounts of waste material. This phenomenon, known as internal waste, is a function of the variability of the grades, the size of mining unit and the amount of sampling information on which ore-waste decisions are made.In this study, it was proposed to consider the effect of internal waste caused by selective mining, on. pit design, using geostatistical methods to predict the tonnage and grade of recoverable reserves within large blocks.Optimum pits obtained using a block valuation formula taking into account the recoverable reserves within large blocks were compared with optimum pits obtained using a conventional block valuation formula. It was found that the optimum pits obtained by the proposed method had the highest total valuations and thus were, in fact, ""more optimum”. These pits were characterized by greater are tonnages at a lower average grade, the additional ore more than compensating for the drop in grade. It was also found that the consideration of internal waste in pit design could considerably alter pit limits in marginal areas of the deposit.It was concluded that selective mining had a significant, potentially critical, impact on the design of optimum pits especially in the case of large low-grade deposits."

Jan 1, 1984

This paper generalizes open stopes into elliptical cross sections and applies the results of calculations based on the mathematical theory of elasticity to indicate stress distribution on the boundaries of such stopes. These show both compressive and tensile stresses and provide an ex-planation for the development of excessive dilution in shrinkage toping. Introduction T HE stress pattern around shrinkage stopes is identical with that around other stopes under the same physical conditions. However, a shrinkage stope ends as an unsupported open stope, and the method i limited to the stress range within which the rock is generally self-supporting. If it is acceptable to generalize the outline of a shrinkage stope into an elliptical cross section, then the graphs of Geldart & Udd (1) (see also Panek (2) and Denkhaus (3)) provide a good base for approximating the stress distribution as mining progresses. However, with failure conditions in the walls, the axis ratio, as cut

Jan 1, 1964

By L. E. Djingheuzian

"ForewordTHE FOLLOWING excerpt is taken from Fine Grinding Investigations at Lake Shore Mines (C.I.M., Trans., Vol. XLIII, 1940, p. 307):""MacCalman, who has carried out exhaustive testing on the accuracy of screen analysis, makes the following statement in his report, The Accuracy of Sieving Tests, Industrial Chemistry (London, England), Vol. XIV, p. 231:"" 'It will be shown that, as no specific relationship between the sieving value and the various dimensional features of the sieve is evident, though there is an apparent tendency for the sieving value to follow the average aperture size, it is apparently impossible to define the sieving value of a screen from dimensions alone, and the calibration of sieves for important tests on a specific material, whereby the sieving values of these sieves are related to that of an arbitrarily chosen master sieve by correction values, will be recommended."" 'It will be emphasized that these correction values are probably not applicable to other materials, or the same material of different size composition. Sieve users, for important tests or in cases of dispute, will be recommended to calibrate their sieves against a mutually acceptable standard with specified conditions of test, and to recalibrate at intervals' ""."

Jan 1, 1953

By F. H. Samuel, P. Burke, F. Mucciardi, J. Gruzleski, S. A. Musmar

A new thermal analysis technique has been developed and tested. It utilizes the enhancement in heat transfer characteristics associated with a recent advancement in heat pipe technology. Heat is extracted from a liquid sample of a melt taken in-situ within a vessel or furnace. The rate of heat extraction is such as to cause the sample to solidify. The technique was tested in both laboratory scale and industrial scale (Grenville Castings, Perth, Ontario). A 356 Al Alloy, subjected to various melt treatments was used to perform the tests. Classical thermal analysis was also performed simultaneously using a preheated graphite cup and at the same melt conditions. The comparison showed the potential of the new technique over classical thermal analysis. The major advantages of the new method are that it conducts the analysis inside the melt (i.e. a physical sample is not removed from the melt), it consumes less time and the cooling rate can be precisely controlled during the solidification process. Moreover, the resolution of the results is better than that of conventional techniques. Aluminium

Jan 1, 2006

By R. Bonifaz

The Chagres Smelter, part of the Anglo American plc group situated 80 Km north of Santiago in Chile, completed a series of operational improvement in 2005 resulting in an optimum capacity in its operational units. At present the Chagres Smelter has developed an operational strategy which seeks to reduce bottle-necks in the production process. In this way we have managed to lower operational cost, decrease energy consumption and maximize the capacity of the Acid, Oxygen, and Smelting, Converting, Refining and Casting units. A constant application of international benchmarks together with continuous staff improvement and the latest smelter technology have combined to place Chagres among the finest smelting works in the world. In response to environmental challenges, we have studying various options for investment suitable for a profitable business of benefits to both Anglo American and Chile as a whole. The most relevant technical indicators are the figures : Energy consumption less than 6,3 GJ/ton fine copper, Intensity of smelting rate in Flash Smelting unit of 6900 ton of copper concentrate/m2 settler of furnace area and be one of the top five smelter in direct cash cost .

Jan 1, 2007

By Derek Harvey

"The paper briefly describes the development of the Eickhoff ESA60 roadcutter which is based on the old and well used principles of the shearer loader. It is intended to show that the machine offers a viable alternative to the normal methods used for driving roadways and also for coal production . References are made to installations currently operating in Europe with applications ranging from roadway drivage to pillar recovery. The paper also looks at possible applications in Canada.IntroductionThis paper is an attempt to show how the principles used in mechanical cutting, conveying and roof support are being applied to a development system capable of catering to a variety of situations and conditions. It is also intended to illustrate how the same system can be used as a total mining system for the mining of many minerals.In order to give some sort of time perspective to the age of the principles, reference can be made to an article in Coal Mining & Processing which states:- During World War II the Germans developed the "" panzer"" or armoured face conveyor.- After the war the English developed power cutters or trepanners that were mounted on the face conveyor, this then developed into the shearer.- The first shearer was produced by the Anderson Company in England in 1950 and shortly after that the Eickhoff Company started manufacturing shearers in German y.- The first hydraulic roof support was produced in 1954 by Gullick.This is a potted history of the three major components of the new system, i.e.:- Mechanical cutting element based on the shearer.- Transport element based on the panzer.- Optional roof support based on the hydraulic face supports.It can therefore be said that since the "" youngest"" of the elements was produced in 1954 the principles of the system in respect of the rapid change in mining equipment are in fact old.Of the three major components the most important is the cutting element since the major benefits of the system are to be obtained from this."

Jan 1, 1985

By K. E. Harley, M. J. Whiting, T. J. Sabin, E. M. Ryan, J. F. Watts

"Wire and Arc Additive Manufacturing (WAAM) has the potential to enable a very significant reduction in buy-to-fly ratio compared to conventional manufacturing through the ability to build near-net shape components. Components manufactured from AA 2319 by WAAM can exhibit significant levels of porosity. There is also a variation in the physical appearance of the surface deposit sometimes found on such components. This deposit is similar to those observed on aluminium joined by MIG and TIG welding processes. It has been suggested that both the bulk porosity and the surface deposit are caused by hydrocarbon-based lubricant on the feedstock wire. An established correlation between surface deposit and porosity would offer valuable insight into WAAM products and enable early interventions in quality control or process monitoring based on visual examination. The relationship between the nature of the surface deposit and porosity has been studied for AA 2319 WAAM components manufactured using different wire batches. Evidence is presented to support the assertion that (i) there does not appear to be a relationship between surface deposit coverage and porosity, (ii) batch-to-batch variability in feedstock wire affects porosity. This study has led to a better understanding of the cause of porosity in WAAM components.INTRODUCTION There is a high cost associated with conventional, subtractive manufacturing because of the high ‘buy-to-fly’ ratio, a measure of the initial material bought compared to the material found in the finished part (Allen, 2006; Yilmaz & Ulga, 2016). A typical aerospace product may have up to 90% of the purchased billet of forging machined away which is cost inefficient and high in material waste. Wire and Arc Additive Manufacturing (WAAM) has the potential to reduce costs and lead time. Robotically controlled weld torches rapidly deposit feedstock wire in layers to build large near-net shapes with mechanical properties similar to those of conventional manufactured parts (Sequeira Almedia & Williams, 2010; Martina et al., 2012; Ding et al., 2015; Williams et al., 2015). A high level of porosity variation has been observed in aluminium WAAM parts (Cong, Ding & Williams, 2014; Gu et al, 2016) which can result in a range of material properties (Rudy & Rupert, 1970). This leads to difficulties in regards to standardisation and qualification of process and parts. In order for WAAM to be used commercially, porosity will need to be understood, monitored and reduced to a reproducible acceptable level or eliminated."

Jan 1, 2018

By Margaret Armstrong, Normand Champigny

"In order to define the ore/waste boundaries as finely as possible, mine planners often insist on kriging very small blocks (relative to the spacing of the available sample grades). These kriged estimates for very small blocks are over-smoothed. For several simple sampling patterns the relation between the block size and the variogram range, and the kriging results were studied. Meaningful estimates of individual blocks are obtained when the variogram range is large compared to the block size and the sample spacing. For a variogram range less than half the sample spacing, the kriged block estimates were found to be uncorrelated with the actual grades. The over-smoothed estimates should not be used for calculating recoverable reserves IntroductionNowadays most mining companies know that the geostatistical estimation method, kriging, gives the best estimates of individual block grades. As most mining engineers and geologists are now familiar with the basics of geostatistics, the definitions of the variogram and of kriging will not be repeated here. An appendix containing definitions and mathematical formulae is given at the end of the article for the sake of completeness.Even though it is well known that the kriged estimates for very small blocks are over-smoothed, mine planners who want to define the ore/waste limits as finely as possible (especially for selective underground mines), are often tempted to krige very small blocks. So we ask how small is ""too small""? Clearly ""smallness"" cannot be expressed in yards or metres. It depends on the nature of the orebody under study and this is reflected in the variogram model chosen to describe it.To answer this question, the changes in four key parameters are studied:• the kriging variance,• the variance of the estimated grade,• the slope of the linear regression of the true but unknown grade on its estimated value, and• the coefficient of correlation between the actual grade and the estimate;as a function of the block size and the variogram range. (Definitions of these four parameters are given in the appendix). Ideally the kriging variance should be low while the variance of the estimated grade should be equal to the dispersion variance of the blocks. The slope should be l.0, and so should the correlation coefficient.These four parameters have been calculated for several simple 2-D examples. The effect of using kriged block estimates that are too heavily smoothed are shown, and the dangers of trying to use these estimates for predicting recoverable reserves for small blocks (i.e. selective mining units) are pointed out."

Jan 1, 1989

By E. Ghali, J. F. Dorion

This paper presents the results of on-going investigations on the influence of corrosion on the performance of support systems in selected underground gold mines. Rock support is exposed to various conditions that can be aggressive. Samples of corroded support were analysed using SEM and photomicrography to determine the main corrosion forms. Tests are on-going in controlled corrosion chambers to qualify and quantify the impact of rock and minerals particles on steel corrosion. As more data become available these relationships can lead to useful information on the choice of support systems and reliable estimates of their longevity.

Jan 1, 2011

By M. Walmsley, D. Maynard

"This paper describes the use of terrain and soil information in the planning of mine developments, particularly in satisfying many of the existing provincial regulatory requirements. It is also noted that, if properly used, this will provide a solid data base for cost-efficient and environmentally acceptable land use.IntroductionIn planning the development or expansion of a new or existing mine, engineering alternatives are judged on many factors, one of which is the environmental influence. Ecological investigations, ensuring consideration of a rational approach to managing land use and environmental impacts, should be carried out prior to a final decision being made on mine development. The Pit Slope Manual (CANMET, 1976) suggests that both baseline aquatic and terrestrial data be collected and interpreted in such pre-mining surveys. In British Columbia, planning procedures now exist which incorporate biophysical studies to help identify, assess and manage major environmental impacts associated with mine development.Methods outlined in the Guidelines for Coal Development (E.L.U.C., 1976) have been successfully applied in recent years. Following this example, the Inspection and Engineering Division of the B.C. Mineral Resources Branch prepared guidelines to help expedite the development of new base metal mines (Procedures for Obtaining Approval for Metal Mine Development; Ministry of Energy, Mines and PetroleumResources, 1979).The metal-mine guidelines require the proponent of a new mine development project to prepare a two-stage assessment proposal which systematically moves from a preliminary feasibility study (Stage I) to a final project design (Stage II), including application for regulatory approvals. One purpose of the Stage I report is to provide a description of the existing environmental conditions that could be affected by the proposed development. A preliminary environmental impact assessment should also be reported. The Stage II report will contain detailed assessment and management of environmental impacts."

Jan 1, 1981

By Yongfeng Jia, Shaofeng Wang, Danni Zhang

Arsenic in mineral processing solutions and effluents is commonly removed and immobilized via iron(III)-arsenatecoprecipitation. The effect of re-crystallization of 2-line ferrihydrite on the long-term stability of iron(III)-arsenate coprecipitate is still not fully understood. This work investigated the redistribution of arsenic and iron during 2-line ferrihydrite transformation at different pHs and temperatures over time. X-ray diffraction (XRD), transmission electron microscopy (TEM) and chemical extraction were employed to characterize the crystallinity of the iron oxyhydroxides. Results showed that the amount of arsenic released into solution during aging increased significantly with increasing media pH.

Jan 1, 2014

By C. J. Rockingham

"A comparative study of sulphide textures has been carried out on samples from four Archean copper-zinc massive base metal sulphide deposits: Kidd Creek, Ontario; Lake Dufault -Norbec, Quebec; Hood River-41, N. W. T.; and Geco, Ontario. These deposits have undergone metamorphic recrystallization under a range of conditions, and results of this study indicate that certain sulphide textures may be used as qualitative indicators of metamorphic grade, whereas other cannot.The sulphide textures of most value in this regard are sulphide grain sizes, which increase with increasing metamorphic grade, and the presence or absence of sedimentary/diagenetic textures, which are destroyed at the lower amphibolite facies of metamorphism. Chalcopyrite and pyrrhotite intergrowths in sphalerite increase in size, in degree of coalescence and in the ratio of unmixed pyrrhotite to chalcopyrite inclusions with increasing metamorphic rank. With increased metamorphic grade, the pyrrhotite intergrowths change from rounded inclusions on grain boundaries to rod-like shapes along sphalerite twin planes. There is also a general increase in the relative proportion of pyrrhotite in the deposits. Textures that appear to have little value as indicators of metamorphic grade are sulphide deformation textures, and triple junction point angles and their standard deviations, which show little variation from the lower greenschist to the upper amphibolite facies of metamorphism. The presence or absence of myrmekite-like magnetite also has little value in determining the relative metamorphic history of these deposits, as it is a product of local contact metamorphism."

Jan 1, 1980

By Henry Brehaut

"It is difficult to know how much environmental information is absorbed by those in a position to put it to use. The following information may seem like ""old stuff"" to those whose companies are taking steps to improve their environmental performance. This paper is directed in particular to those people who are interested in determining what further changes are required to make improvements as concerned environment citizens.IntroductionUntil recently, the author was comfortable with the fact that none of the operations for which he was responsible had any environmental charges against them. It was not until one of his operations was charged with non-compliance that the author discovered due diligence as a way to avoid a second charge, and when an unfortunate spill occurred at another operation, the meaning of risk prevention was learned. Knowledge was gained step by step to the point where finally environmental information is being heeded, rather than waiting to learn from sad experience. With the appreciation of what it takes to do a good environmental job, comes an understanding of the challenge that lies ahead, and the fact that there is a lot to learn.At a recent environmental gathering, comments from the participants varied considerably. Some just didn't understand why government was being so unreasonable, while at the other end of the spectrum one individual whose company was well along the path to becoming a good environmental citizen remarked that it was all very basic. What was immediately understandable to one went right over the heads of others, indicating the different stages that have been attained in the acceptance of environmental responsibilities."

Jan 1, 1991

By M. Maldonado, P. Olivares

"A submersible sensor for real-time gas holdup measurement in the collection zone of industrial flotation machines is introduced. The working principle is based on the generation and measurement of a pulp flow using a gas-exclusion cell immersed in the aerated slurry. The gas exclusion cell consists of a variable-area open vertical tube designed to be filled only with pulp by preventing gas bubbles entrance. The higher density of the fluid column within the cell generates a downward flow of pulp; the rate of this flow is proportional to the gas holdup outside the cell. The gas holdup measurement is achieved by tracking the velocity of the pulp flow leaving the gas-exclusion cell, using a magnetic flowmeter. Construction details of a prototype and its testing in two- and three-phases are discussed.INTRODUCTIONFlotation process optimization consists of finding and maintaining operating conditions that maximize flotation performance measured in terms of recovery and grade. The selective separation of mineral particles proceeds in two interactive zones where different and simultaneous phenomena take place: in the collection zone, the valuable particles are separated by collection on the surface of bubbles, while in the froth zone, the bubble-particle aggregates are gathered, drained to remove entrained particles, and taken into the concentrate stream. The cell overall performance, which can be determined from proper stream sampling, is a function of the recoveries in the individual zones. These zone recoveries cannot be independently measured nor calculated from operating variables. Progress in the assessment of these recoveries has been slow because on-line and reliable sensors to measure properties of the drastically different dispersions existing in both zones are not available.In the case of the collection zone, it has been demonstrated that the recovery of hydrophobic particles on the surface of bubbles, considered as a process with first-order kinetics, correlates with the bubble surface area flux (Finch et al., 2000; Hernandez, et al., 2003; Lopez-Saucedo et al., 2012). Bubble surface area flux (bubble area generated per unit time and cell cross-sectional area), is a variable affected by gas flow rate, bubble size distribution, and frother type and concentration. Gas holdup (volumetric fraction of gas dispersed in the slurry) is also affected by the same variables, and as such, carries information on the interacting variables that define the performance of the process. Therefore, a correlation between gas holdup and bubble surface area flux was expected and demonstrated (Finch et al, 2000), and since gas holdup is easier to measure as no bubble size is required, it has the potential to be the basis of a cell control and optimization strategy if a continuous sensor is available."

Jan 1, 2016

By Malcolm R. Gent

"The presence in Saskatchewan of sixteen kimberlite pipes of probable late Albian age has been reported. An abundance of aeromagnetic anomalies possibly attributable to kimberlite pipes have been identified and it is anticipated that industry has acquired reasonable proof of the presence of more than seventy k imberlite pipes in Saskatchewan. Historical reports of diamonds, the discovery of kimberlite pipes and these aeromagnetic anomalies indicate the Phanerozoic Basin and some parts of the exposed Shield in Saskatchewan have an excellent potential f or the occurrence of economically exploitable diamond deposits. The presence of some igneous minerals found in some salt solution breccias also indicates the probable occurrence of extensive diatreme activity during the Devonian.A Laramide Orogeny-induced crustal hinging or arching of the eastern margin of the Phanerozoic Basin and probably dextral wrenching-induced arching and faulting within the basin are proposed as major factors in the emplacement of Cretaceous or younger kimberlites. Zones of crustal weakness between subcratonic Archean blocks and internal faults are also thought to be significant controlling factors in the location of kimberlites in Saskatchewan.Mapped aeromagnetic anomalies interpreted as being possibly due to kimberlite pipes generally tend to be concentrated in, areas underlain by a basement of or with components of Archean age. Within Saskatchewan, these anomalies occur within the probable Trans-Hudson Orogen zone; the Rae-Hearn Craton margin; and the northeast flank of the Elkpoint Basin. Recognized areas of potential f or kimberlite emplacement are the Phanerozoic basin margin, the western limit of the Superior Province adjoining the Churchill Province, and a swath approximately 150m wide along the northeast-southwest trending Shaunavon linear and other areas of inner basin arching."

Jan 1, 1992

By J. D. McFarlane, V. Robinson

"The paper begins with a brief account of the naturarly occurring resources of gypsum and anhydrite and a discussion of their relative value and utility as sources of sulphur. The fundamental chemistry of recovering sul-phur values from calcium sulphate is discussed. (a) Thermal decomposition -discussed as impracticable; (b) Reduction to calcium sulphide; (i) Total Reduction-The chemistry is outlined and the Dorr-Oliver and Bureau of Mines processes mentioned. The Elcor process is mentioned and certain deductions made from available information.(ii) Partial Reduction-This is stated as the basis of the only proven process, namely ""The Cement -Sulphuric Acid Process."" The possibility of recovering lime is mentioned as an aside, but dismissed for lack of commercial application. The history of the cement -sulphuric acid process is covered briefly and a list of plants in commercial operation included. A brief elementary account of the basic chemistry of cement production is followed by a discussion on raw materials and fuels. A short account of the flow scheme of a typical plant, with notes on the operating peculiarities, precedes an account of product quality. The latest developments which enable by-product gypsum to be used as a raw material are discussed, with an indication of how the flow scheme is modified. A statement of feasible plant capacities is followed by requirements of raw materials, services, labour, etc., and finally some indication is given of capital costs."

Jan 1, 1969

By James A. Finch, Yue Hua Tan, Wei Zhang

"The paper is part of our study of the frother structure-property relationship using bubble rise velocity. Single bubble rise velocity profiles were determined in a 350 cm column for surfactants from the polypropylene glycol (PPG) family. Using velocity at 300 cm, the concentration to reach minimum velocity (CMV) is determined. The CMV is shown to decrease as alkyl chain length (n, number of carbons) increases and as the number of propylene oxide groups (m) increases. Linear correlations log CMV vs. n and m were observed. Taking literature data for critical coalescence concentration (CCC), linear log CMV vs. log CCC correlations were also noted. Mechanisms are briefly discussed, and prediction of CCC made for a commercial polypropylene glycol.INTRODUCTIONAs one of the great enabling technologies of the 20th century, froth flotation is a highly versatile method for physically separating minerals by exploiting differences in wettability (hydrophobicity). Over the last century, flotation reagents have undergone significant developments (Khoshdast and Sam, 2011). One important group of reagents is frothers which are used to reduce bubble size, slow bubble rise velocity and help stabilize froth (Klimpel and Isherwood, 1991).Frothers, originally derived from natural sources (e.g., pine oil and cresylic acid), are largely replaced today by synthetic products which provide more consistent properties. Polyglycols, based on PEO (polyethylene oxide), PPO (polypropylene oxide), or PBO (polybutylene oxide) groups, were first described by Leja and Nixon (1957) and have attracted wide use since then (Farrokhpay 2011). The chemical structure of polyglycols can be represented by a general formula: R(X)mOH, where R = H, or CnH2n+1 and X stands for EO (-C2H4O-), PO (-C3H6O-), or BO (-C4H8O-). The polypropylene glycol ethers (CnH2n+1(PO)mOH) are the most common of these reagents (Pugh, 2007) and the focus of this study.In general, the chemical structure of frother molecules comprises two parts, a non-polar hydrophobic hydrocarbon (alkyl: CnH2n+1) chain and a polar hydrophilic head. By introducing the ether -Olinkage, which acts as another polar site, the propoxy group (-OC3H6-) in the structure makes the frother readily soluble in water (Somasundaran and Wang, 2006), facilitating the industrial use of these frothers. Available as by-products, Dow Chemicals introduced as series of polyglycols, e.g., Dowfroth (DF) 200, 250, 263, and 1012, the most familiar being DF250 (CH3(PO)4OH), a polypropylene glycol methyl ether. While no longer available from Dow, these and other polyglycols are still widely used."

Jan 1, 2016

By J. G. Schofield, R. C. Francki, K. M. Donaldson, F. E. Ham

"Developments in pyrometallurgical technology have led to larger furnaces operating under more intense process conditions. In order to maintain the reliability of these furnaces, which are frequently single-line units, the design of the refractories, cooling systems and bindings has become more critical. Traditional thermal and chemical requirements for the refractory to resist slag attack must still be carefully determined. The larger, modem furnaces have placed a new emphasis on the structural properties of the refractories as well as their thermal properties to suit the extensive cooling systems. Based on operating experience, supported by computer models, the refractories and bindings are designed to work together to accommodate the thermal expansions and contractions in order to minimize permanent furnace growth and the risks of leaks. IntroductionElectric furnaces are used extensively in smelting copper and nickel ores and concentrates. Laterite nickel ores and high-magnesia copper, nickel and platinum sulphide concentrates are smelted virtually exclusively in electric furnaces to accommodate the high melting point of the slags produced. Although a number of smelting processes using oxygen-enriched and/or preheated air have been developed to replace reverberatory furnace smelting of conventional copper and copper-nickel concentrates, (lnco, Noranda, Outokumpu, Mitsubishi) electric matte furnaces remain a strong process alternative for these concentrates, either as the primary smelting vessel or for cleaning the slags produced from these processes.The development of large, high-powered furnaces has been an important factor in the growth of electric smelting technology, as evidenced by the list of operating matte and ferronickel furnaces shown in Table I. Because the compressive forces required to maintain a tight, leak-free furnace increase with furnace dimensions, the selection and design of the furnace refractories, cooling systems and bindings require increased attention."

Jan 1, 1993

By J. Thiriar

The electrolytic tan/chouse at CCR was recognized by management as lagging behind modem refineries in terms of productivity, energy efficiency and controls. The operation was also burdened by high maintenance costs of cells, floors and electrolyte recirculation systems. A bench marking program was started in 1986 to evaluate processes and other technology by visiting major copper refineries in North America, Europe and Japan. The basic principles necessary to optimize the operation were defined, and a program called CCR 2000 was prepared for approval of the necessary capital investments. This paper describes the results obtained to date and outlines the remaining work to complete the modernization program, in particular, the control of electrolytes, the elimination of the Baltimore groove and studies to modernize the stripping operation or adopt permanent cathode technology.

Jun 1, 1993

By A. Zangooi, J. A. Finch

Flotation is a separation process based on the collection of particles on the surface of bubbles. Flotation machines disperse air into bubbles using a variety of techniques. The characteristics of the bubble population are strongly affected by the selection of frother type and concentration. As metallurgical results depend on the bubble distribution, the measurement of frother concentration is vital to understand and control performance. A previously developed colorimetric technique was refined to work with low solubility frothers and to increase daily analysis rate. Field-testing demonstrated that the method is robust, reliable and accurate. As well as relating frother concentration to gas dispersion measurements, the results can be used to answer operational questions including: how well a frother dissolves, how reliable and stable frother delivery is, how evenly frother is distributed down a bank, and whether frother distributes between the pulp and froth zones. Some of these points are illustrated from plant experiences. Advances in Mineral Processing Science and Technology Proceedings of the 48th Annual Conference of Metallurgists ofCIM Sudbury, Ontario, Canada Edited by

Jan 1, 2009