Search Documents

By Phil A. Keele

"IntroductionGeneralThe Genesee Coal Mine is a joint venture of Fording Coal Limited and the city of Edmonton. The mine supplies thermal coal to the Genesee Generating Station operated by Edmonton Power and is located approximately 75 km southwest of Edmonton (Fig. I).Under the terms of the joint venture agreement, Fording Coal Limited has designed and developed the Genesee Coal Mine. Fording also operates the mine which has a minimum economic life of thirty-five years. Mine development started in the spring of 1987 with the construction of the dragline erection pad and mine service complex. Major development of mining areas was carried out in 1988 with the construction of haul roads, powerlines, topsoil recovery, etc. Mining officially commenced on December 14,1988.The mine produces 1.6 million tonnes of coal per year and employs 65 people. MiningGround conditions have turned out to be very poor, as expected with the majority of the overburden in the first few years a soft lacustrine clay with minor amounts of fine-grained glacial till. To compound matters, what was expected to be a relatively uniform coal subcrop turned out to be a very irregular erosional contact.The coal mined at Genesee is a sub-bituminous Class B thermal coal with approximately 16070 ash, 21% moisture, 8300 Btu/lb and 0.27% sulphur on an as-mined basis.The primary piece of mining equipment used at the Genesee Coal Mine is a M8200 walking dragline. It has an effective operating radius of 100.6 m, a 50.5 m3 bucket, and weighs approximately 3860 tonnes yielding a ground pressure of III KN/m2•Figure 2 illustrates schematically the single pass mining sequence presently employed at the Genesee Coal Mine. The M8200 is used to lift all coal out of the cut, the coal being placed in stockpiles on the prepared pad .This method maximizes coal recovery under the conditions where spoil failures due to poor material would otherwise put men and equipment at risk. The coal is subsequently loaded by the coal shovel operating on the same bench as the M8200 dragline and delivered to the plant as required.All mined areas, as required under Alberta Legislation, are to be returned to an agricultural land capability equal to or better than that which existed prior to mining. Reclamation activities, as a result, are an important and integral part of the mining process. A complete list of the primary mining equipment deployed at the Genesee Operations appears in Table I."

Jan 1, 1994

By A. J. Stapleton

"This paper gives a brief description of the occurrence and development of the Needle Mountain mine at Gaspe Copper Mines, Limited and describes the trackless mining equipment used in this highly mechanized underground operation.Maintenance of the trackless equipment is considered in detail, with particular emphasis on scheduling and control, examination and inspection. All maintenance is carried out in an underground garage, and the facilities for maintenance and field repairs are also described. Maintenance costs are given for various units and the figures for different types of loading and haulage units are compared to support the trend toward larger units and the increasing use of rubber-tired loaders."

Jan 1, 1969

By R. Liu

As Building Information Modeling (BIM) becomes widely adopted by the construction industry, it holds undeveloped possibilities for supporting Facility Management (FM). Some FM information systems on the market claim to address the needs for FM requirement. However, the question of whether the functionalities provided by the current BIM-based FM software companies are those actually required by the FM Professionals still need to be answered. The data is required by FM professionals in the operation and maintenance phases of facilities and type of maintainability problems that frequently occur, which can be solved early in design phase, have not yet been addressed. The aim of this paper is to clarify the frequently occurring maintainability problems and to investigate the potential areas that can use BIM technology to solve the maintenance problems in early the design phase. A survey was conducted to collect perspectives from the industry practitioners for the maintenance problems and their frequency. The survey results indicated that maintainability considerations should be taken into consideration during the facility design phase. The results also address the perceived areas by practitioners that need maintainability consideration in design phase

Aug 1, 2013

By G. W. Sparkes

The use of CR-39 plastic polymer as a solid state nuclear track detector in the textural analysis of radioactive minerals in geological samples was first described by I.R Basham in 1981. CR-39 autoradiographs provide a detailed, high-resolution image of the in situ distribution of the radioactive minerals within geological samples on both the macroscopic and microscopic scales. This technique is an inexpensive and effective means of obtaining detailed textural information that provides insight into the style of mineralization, its relationship to primary and secondary structures in the host rock, and its association with particular geological features or mineral phases. Although this technique does not provide any information on the identity of the minerals responsible for the radioactivity, the resultant autoradiographs can be used to select regions for further detailed analysis such as petrography, microprobe analysis, or SEM imaging. This paper summarizes the procedure and outlines the appropriate time and materials required for both the exposure and etching of the CR-39 with respect to the intensity of the radioactivity emitted by the geological samples.

Jan 1, 2013

By J. M. Harrison

FIELD PARTIES of the Geological Survey of Canada have, in recent years, mapped several areas east and northeast of Flin Flon (9, 10, 12, 13, 14, 15, 118) (1). In all these areas the mineral deposits show a close geographical relation to faults although the immediate control of most of the known ore deposits appears to be folded structures in the rocks (8, 11, 18, 19). Air photographs and published geological maps were studied in order to ascertain whether or not the mineral deposits in the Flin Flon-Snow Lake mineral belt as a whole show any spatial relationship to faults. It was found that most of them do show a distinct geographical association with faults, or with topographic features that may be faults. It is further apparent on air photographs that a major lineament, for composite of lineaments, follows approximately the contact between gneisses and schists of the Kisseynew complex on the north, and Amisk volcanic rocks on the south. However, this Kisseynew lineament is not continuous and, especially in the eastern half of the district, it is exceedingly irregular in plan. Parts of this lineament have been mapped as faults (9, 10, 12, 14), other parts have been shown as stratigraphic contacts (1, 2, 21, 27), and still other parts have not been studied except by reconnaissance methods. It is suggested that the Kisseynew lineament may be due to a deformed fault that extends easterly from a point about 25 miles west-northwest of Flin Flon to a point at least 10 miles northeast of Wekusko lake and that the mineral deposits.

Jan 1, 1951

By Donald Brisebois

The mining of high-grade, narrow vein deposits is an important field of activity in the precious metal mining sector. The principle factor that has undermined the profitability and effectiveness of mining such ore zones is the substantial dilution that occurs when blasting with explosives during extraction. In order to minimise dilution, the Thermal Fragmentation Mining Method enables the operator to extract a narrow mineralised corridor, 50 cm to 1 metre wide (according to the width of the vein), between two sub-level drifts. By inserting a strong burner powered by diesel fuel and compressed air into a pilot hole previously drilled directly into the vein, a thermal reaction is created, spalling the rock and enlarging the hole to 80 cm in diameter. The remaining ore between the thermal holes is broken loose using low powered explosives, leaving the waste walls intact. This patented method produces highly concentrated ore, resulting in 400% - 500% less dilution when compared to conventional mining methods. The mining method reduces the environmental affects of mining operations since much smaller quantities of rock are displaced, stockpiled, and treated using chemical agents. The fully mechanised equipment operated by a 2-person team (1 thermal fragmentation operator, 1 drilling operator) maximises the effectiveness of skilled personnel, and increases productivity and safety. The Thermal Fragmentation is currently employed in 3 mining operations in North America.

May 1, 2010

By G. V. Fernandez

Sociedad Minera Cerro Verde S.A.A leaches secondary copper sulfides. In recent years, the mine has introduced innovations that have improved the management of mineral crushing, agglomeration, curing, and leaching. The crushing plant, for example, uses the concepts of degree of balance and percentage of time in an operationally balanced state which, displayed in real time, facilitate more intensive and uniform utilization of the crushers. High agglomerate quality is ensured with the correct dose of moisture, which is adjusted to the changing characteristics of the mineral through the use of electrical conductivity measurements. The amount of acid used for curing the agglomerate is also adjusted by using quality control information. Finally, the stockpile irrigation regime is managed using the criteria established by the "Lixiviant Request Rate", which optimizes the addition of leaching solution, creating such benefits as faster recovery, and reduced acid and energy consumption.

Jan 1, 2007

By William E. Roscoe

"Valuation methods are well established for mineral properties with production or imminent production, and include discounted cash flow and comparable transactions. Valuation methods for non-producing mineral properties, however, are more subjective. Non-producing mineral properties include those at various stages of exploration, properties at the prefeasibility or feasibility stage, properties with currently uneconomic mineral resources, and past-producers. Different valuation methods may be appropriate for different types of mineral properties.Income approach methods such as discounted cash flow and option pricing are generally not applicable to properties at the exploration stage. The market approach is generally appropriate to all types of mineral properties, although it is difficult to find good comparables because of the unique nature of mineral properties and the small number of transactions. Cost approach methods, such as appraised value and geoscience factor, are commonly used for exploration stage properties.Canadian standards and guidelines for valuation of mineral properties are in the process of being finalized by a Special Committee of the Canadian Institute of Mining, Metallurgy and Petroleum (CIMVal Committee). The CIMVal Standards are intended to be consistent with National Instrument 43-101, which sets regulatory standards of disclosure for mineral projects, and with International Valuation Standards. The intent of the CIMVal Standards and Guidelines is that mineral property valuation be carried out by appropriately qualified individuals and that all relevant information be disclosed."

Jan 1, 2003

By M. J. Collins, B. Parekh, A. Hasenbank, B. Hewitt

Newcrest Mining Limited, originally as Lihir Gold, has operated a pressure oxidation plant for the recovery of gold from refractory ore since 1997. The mine and gold plant are located on Lihir Island in Papua New Guinea. Design of the original pressure oxidation circuit was based on the results of pilot plant tests conducted by Sherritt in Fort Saskatchewan. Following a decision to expand the plant in 2008, Lihir Gold contracted Sherritt to design a new autoclave. The design exercise utilized the original pilot plant test results, commercial process results at Lihir, and an understanding of advances in autoclave technology since the original plant was built. The new Lihir autoclave will be the largest horizontal, multiple-compartment autoclave in the world. The design process for the pressure oxidation expansion is described in this paper.

Jan 1, 2011

By A. Motamedi

Indoor localization has gained importance as it has the potential to improve various processes related to the lifecycle management of facilities and to deliver personalized and location-based services. Radio Frequency Identification (RFID) based systems, on the other hand, have been widely used in different applications in construction and maintenance. This paper investigates the usage of RFID technology for indoor localization of RFID equipped movable assets during the operation phase of facilities. The location-related data on RFID tags attached to fixed assets are extracted from a Building Information Model (BIM) and can provide context-aware information inside the building which can improve Facilities Management (FM) processes. The paper proposes a new approach to use received signals from available reference tags in the building attached to fixed assets to locate movable assets. The approach uses signal pattern matching and clustering algorithms for localization. As a result, a user equipped with an RFID reader is able to estimate the location of target assets, without having access to any Real- Time Location System (RTLS) infrastructure. A case study is performed to demonstrate the feasibility of proposed methods.

Aug 1, 2013

By T. Imgrund, A. Bischoff, S. Spürk

"Specific conditions of underground coal mines at great depth, such as high temperatures, high rates of methane inflow and natural ventilation pressure provide considerable challenges for the reliable design of appropriate mine ventilation systems. For decades coal mining in Germany has coped with these extreme circumstances. Based on these experiences appropriate software tools for simulating mine ventilation networks have been developed and continuously enhanced. This paper examines differences in the simulation results and underlying calculation methods of two software solutions. The analysis is based on the comparison of FlowNetTM and VentSim DesignTM (Version 5.1) regarding the accurate prediction of fluid mechanical quantities and their validation with real measurements. A special focus lies on exceptional ventilation scenarios typical for deep coal mines, like gas inflows, fire events and buoyancy effects. The purpose of the comparison is the future utilization of the experiences gained during mining at up to 1,500 m depth for state of the art ventilation design. INTRODUCTION Ventilation is an essential component of mine operations—as providing fresh air to workplaces, diluting and removing explosive, toxic or asphyxiating pollutants and assuring sufficient climate conditions. On the other hand, the costs of ventilation contribute to a large extend to the overall operating costs of a mine, as the share in the energy consumption of a mine may be in the range of 25–50% (Belle, 2008). Accordingly, proper design of ventilation systems has been a task since early times. Consequently software for modelling of ventilation networks has been developed in order to improve efficiency and accuracy of calculations (Maleki, 2018). Compressible flow has not been considered by initial ventilation modelling software tools. In Germany, the consideration of changes in airflow density—depending on pressure and temperature—in the algorithms of ventilation simulation software has been started in 1974 by Duepre & Hofbauer. This development had been continued by the Pruefstelle fuer Grubenbewetterung (Test Centre for Mine Ventilation) and resulted in the release of a computer ventilation software named “Wetter”. The mine inspectorate of the German state of North Rhine-Westphalia, which supervises the major coal mining district in Germany, declared ventilation simulation based on compressible flow being “state of the art” in 1985 (Pollak, 1985). This pronouncement made allowance for assessing the consequences of underground fires and downtimes of main fans based on advanced software solutions."

Jan 1, 2019

By Sydney H. Ball

It is a peculiar anomaly that while the world uses the term "rich as a gold mine" as the superlative figure of speech descriptive of wealth, the shares of gold mines are not as popular investments in America as certain of them should be. One of the most able of Manhattan's bankers is a director in an investment trust with a portfolio the value of which has gone the way of other such portfolios. Luckily a couple of years ago a few hundred shares of Homestake were purchased, and since then the trust has not only received therefrom satisfactory dividends but has benefitted from a large appreciation in their value. At each directors' meeting, however, the banker in question, Cato-like, suggests the sale of these shares, gold shares being, in his opinion, too speculative to be included in the portfolio of any trust. A short time ago the financial pages of one of our great metropolitan papers featured an article listing the corporations still paying dividends at the 1929 rate. Gold-mining shares were, the article stated, excluded, although in reality every gold mine on the New York Stock Exchange paid higher dividends in 1932 than in 1929. This 'Alice in Wonderland' treatment of the gold-mining shares is admittedly a bit confusing to those of us who believe that the shares of certain gold-mining companies have a rightful place in any well diversified portfolio. It should, however, here be recorded that whereas, fifty years ago, in America, gold-mining shares were considered by the public as instruments of nefarious gambling, now shares of the better gold mines are sought by astute investors. In England for well over a generation their value as sound investments has been widely recognized.

Jan 1, 1933

By M. Medraj, M. A. Arafin, D. P. Turner, P. Bocher

In this study, the kinetics of isothermal solidification during TLP bonding of Inconel 625 and 718 superalloys with nickel based multi-component filler alloy BNi-2 have been studied through a combination of direct experimentation and mathematical modeling in order to determine the effect of process variables and, thus, to optimize the process. The predicted isothermal solidification completion times from the boron diffusion model and migrating solid/liquid interface model were in good agreement with the experimentally determined values and, they were found to be significantly less than those of other nickel superalloys with different nickel based filler alloys. Further, significant reduction of holding time was observed with increasing bonding temperature and with decreasing joint gap. No significant grain growth in the base metals has been observed in the temperature range being investigated (1325 - 1394K).

Jan 1, 2006

By L. E. Reed, I. G. L. Sinclair

An exploration program seeking kimberlite pipes, the common primary hosts for diamonds, Was' conducted during the years 1979 through 1982 in the James Bay Lowlands of Ontario by Selco Mining Corporation (now the Mining Division of BP Resources Canada) and Esso Minerals Canada. The area to be explored was selected on the basis of its regional geological setting, and because of the known presence of kimberlite indicator minerals in the region. The primary exploration technique was low level airborne magnetic surveying, followed by detailed ground geophysics. This work located many pipe-like bodies, with diameters of a few hundred metres, as well as several dykes. Targets located by these geophysical methods were drilled, intersecting a total of45 intrusions, consisting of34 alkaline diatremes containing tuffisitic breccias, 7 carbonatites, and 4 massive alnoites. K-Ar determinations indicated ages of 152 Ma and 180 Ma for two of the massive alnoites. The texture and general mineralogy of the tuffisitic breccias are similar to those of diatreme facies kimberlites, but detailed examination of their mineralogy and chemistry demonstrated that they lie within the alnoitic rather than the kimberlitic compositional field. Although the exploration program did not lead to the discovery of true kimberlites, it did demonstrate the presence of a large, previously unknown province of alkaline volcanic activity, which has no surface expression.

Jan 1, 1991

By F J. Kelly

A chemical process, based on laboratory investigations, is proposed for the production of high-purity niobium oxide from a pyrochlore-perovsk1te flotation concentrate produced from ore obtained at the Oka, Quebec property of Columbium Mining Products Limited. The method developed included the decomposition and dissolution of the flotation concentrate with hot, concentrated sulphuric acid. The dissolved niobium was purified and concentrated by a solvent extraction step, using methyl isobutyl ketone as the extractant. The niobium was recovered from the extractant with ammonium fluoride solution from which niobium oxide was precipitated with ammonia. Finally, the filtered and washed precipitate was calcined. Ninety-six per cent of the niobium was recovered in a product analysing 99.9 per cent Nzo.. The reagent cost was in the range of $1.00 to $1.25 per pound of niobium recovered. Introduction OVER the past few years, Columbium Mining Products Limited has been engaged in the development of a niobium-bearing mineral deposit in the vicinity of Oka, Quebec. One phase of this program resulted in a flotation process capable of producing concentrates containing up to 50 per cent Nb205? Flotation pilot-plant

Jan 1, 1965

By A. Quilodran, B. Jakovljevic, T. McCallum, P. Wong

"Rare earth separation by solvent extraction (SX) requires multiple separation plants each consisting of many extract, scrub, and strip stages to separate the individual metals. SX modeling advances have brought benefits to circuit design and process optimization by quickly narrowing test conditions without the need for exhaustive laboratory studies. Modeling can be used to optimize circuit configuration, O/A ratios, and acidities, which allows for CAPEX and OPEX savings. A comparison between pilot plant data and the results expected from modeling is presented for rare earth separations with CYANEX® 572.INTRODUCTIONRare earth separations can be difficult due to limited separation between the elements (Xie, Zhang, Dreisinger, & Doyle, 2014). This requires relatively complex solvent extraction circuits utilizing multiple extract, scrub, and strip stages as well as multiple SX configurations to achieve the desired metal purities. Designing rare earth circuits can be complex, and significant time and testing may be necessary to determine the required staging and optimal conditions.Circuit modeling for rare earth separations has been introduced to the industry using CYANEX® 572 extractant (Soderstrom, McCallum, Jakovljevic, & Quilodran, 2014). CYANEX® 572 is an acidic organophosphorus extractant formulation which has a weaker ligand-metal complex strength than that of the traditionally used phosphonic acid extractants. This allows efficient extraction while requiring a significantly lower acid concentration for stripping (Wang, Li, Zhao, Dong, & Sun, 2015). The reduced acid requirement in strip is expected to provide OPEX savings.The modeling can be utilized to quickly determine the required acidity and organic/aqueous (O/A) ratio for a given separation. It is also expected to reduce CAPEX requirements as optimal staging can be determined, and implemented.CYANEX® 572, combined with modeling, was utilized to produce a purified dysprosium (Dy) stream. To achieve this separation, multiple SX circuits were designed and operational conditions specified to separate Dy from the mixed rare earth chloride feed."

Jan 1, 2016

By P. Marcotte, G. LeBlanc, S. Ouellette, J. Boutin

"To characterize noise and vibration sources of different types of mining equipment used in underground mining, the authors performed a study in eight Quebec mines on 28 pieces of equipment. This paper presents the procedure followed to select the equipment to be evaluated, and the low-cost acquisition system developed to perform multichannel time-domain data acquisition in harsh environments. It also presents the results obtained for the noise level produced by the equipment and for handarm and whole-body vibration exposures.RÉSUMÉ Dans le but de caractériser les sources de bruits et de vibrations de divers équipements miniers utilisés sous terre, les auteurs ont étudié 28 équipements dans huit mines du Québec. L’article présente la procédure suivie pour choisir les équipements à évaluer ainsi qu’un système multicanal à faible coût développé pour acquérir des données dans des environnements difficiles. Il présente aussi les résultats obtenus pour les niveaux de bruit produit par les équipements et pour les expositions main-bras et du corps entier aux vibrations."

Jan 1, 2015

By B. C. Tripathy, S. K. Padhy, R. K. Paramguru, Pinak Patnaik

"Cobalt is regarded as technology enabling metal among the less abundant metals found in the earth crust. Electrodeposition of the metal from aqueous sulphate solutions is the preferred technology for its commercial production. Certain additives are added in the electrolytic bath during electrodeposition for the production of uniform, smooth and bright deposits of cobalt metal with higher current efficiencies and lower energy consumptions. A detailed investigation has been carried out to determine the effect of additive Sodium octyl sulphate (SOS) on the electrodeposition of cobalt. The results indicated that the additive apart from increasing the current efficiency enhanced the quality of cobalt electrodeposits. A maximum current efficiency of 98.4% was achieved at 10 mg/L SOS. The presence of SOS in the electrolytic bath did not result in any noticeable change in the crystal orientation of the cobalt electrodeposits except at higher concentrations (50 g/L) of the additive. Scanning electron micrographs indicate that smooth, compact and uniform deposits of cobalt were obtained at 10 mg/L of the additive beyond which there is detoriation in the quality of deposits. Polarisation of the cathode was seen in the presence of SOS. The effect of SOS on the electro kinetic parameters: Tafel slope (b), transfer coefficient (a) and exchange current density (I0) has also been investigated.INTRODUCTIONCobalt is recognised to be a strategic metal among the various base metals, owing to its numerous applications in various industries. Cobalt as a metal finds its use in the preparation of rechargeable batteries, as an alloying component in the manufacture of space craft and jet engines, as a drying agent for paint varnishes, ground coats for porcelain enamels and in the manufacture of the catalysts for the petroleum and chemical industries (Davis, 2000). Although there is a huge demand of the metal the supply of the metal is limited due to its scarcity in the earth crust. The metal comprises of only 0.02% of the earth’s crust for which the metal is recovered from various ores of nickel and copper as a byproduct (Hawkins, 1998). The present day techniques for cobalt production includes mostly hydrometallurgical methods which are preferred over the earlier used pryometallurgcial methods carried out for the metal production. Almost 70% of the world’s cobalt produced currently is from hydrometallurgical techniques in which electrodeposition of the metal from aqueous solutions is the final step for metal production (Verney, 1988). The most preferred route for electrodeposition of cobalt metal involves a sulphate medium (Das and Subbaiah, 1984; Lenthall and Bryson, 1997; Sharma et al., 2005)."

Jan 1, 2016

By A. Aaltonen, S. Paloranta, H. Myllykangas

A property based dynamic model of flotation was built and validated for training purposes. The model is based on the work of the AMIRA P9 project. The recovery of each particle with composition and size is calculated in a given simulation step. The model takes into account machine and operational parameters such as air flowrate and froth height. The model was created using fullscale test data on Pyhlisalmi Cu-Zn-pyrite ore with flotation kinetics of multiphase particles determined. Simulation and validation shows that model can predict the dynamic behavior of the process accurately enough for training purposes.

Jan 1, 2009

By S. Steinlechner, G. Schneeberger, J. Antrekowitsch

The recycling of steel mill dusts is getting more and more important. The costs and requirements of land filling are rising and companies are interested in new recycling strategies. The rising of sustaina¬bility hand in hand with the high rate of valuable metals in these residues supports new research activities on the recycling sector. Especially zinc but also iron and lead are economical factors due to the treatment of steel mill dusts. This paper gives a small overview of fundamental studies concerning the chemical and physical composition of these dusts. Furthermore aggregates for the reduction of these dusts in the liquid phase are introduced and compared. The Flash-Reactor, the TBRC-Technology (Top Blown Rotary Converter) and submerged arc furnaces and there use for melting and treatment of these dusts are in the center of interest of this paper. The final conclusion gives an overview of possibilities for reduction of filter dusts in the liquid phase.

Jan 1, 2011