Search Documents

Wetherstones gold deposit is located just east of the township of Lawrence, in the Otago District of the South Island, New Zealand. The paper will describe aspects of the mining and exploration history of the Wetherstones gold field, current knowledge of the geology of the deposit, and speculate on possible outcomes of exploration in the modern era.   As at the famed Gabriels Gully situated nearby, most of the Wetherstones gold is/was contained in, or recycled into modern drainages from, the Blue Spur Conglomerate (æBSCÆ). The BSC is the basal member of a wedge of auriferous non-marine sediments of latest Cretaceous age which are tilted against the Tuapeka Fault Zone, a structure of regional dimensions. In particular mineralisation of elevated grade (which cannot yet be reliably estimated) appears to be concentrated in an elongate basement depression (ægutterÆ) of width around 100 m, variable thickness to a few metres, and axial length in excess of 500 m. The gutter plunges from the base of alluvial mining (where it has been partly exploited by underground methods) to depths of more than 100 m, beyond which it remains open and untested.   The prospects for a revival of mining at Wetherstones depend upon confirmation of what is here inferred to exist, and the discovery of additional gold. The economic prospects of the project however are enhanced by what is known or indicated of the geographic location, and anticipated geologic, mining and metallurgical characteristics of the mineralisation, and consequent anticipated environmental management issues.   The recognition of gold contained in pyrite in the BSC represents an upside to project economics which has never previously been evaluated. The Wetherstones Basin covers more than five square kilometres in areal extent. There is no modern exploration record of the majority of this area, leaving open the prospect of the discovery of additional gutters, and primary mineralisation in the underlying schist.   Australasia Gold Ltd has embarked on a program to reassess the potential resources of the Wetherstones gold mineralisation, and to evaluate the feasibility of mining.

Jan 1, 2004

By Sillet R, Corin P. J, Wilson G

Zinc Corporation of Broken Hi11 had some long hole stopes coming into use which could not be mined using diesel loaders, because of ventilation restrictions. In preference to use of pneumatic loaders, and because there were no field proven electric loaders in Australia, Horwood Bagshaw Ltd., were commissioned to repower a diesel loader with an electric motor, within the confines of the existing machine

Jan 1, 1977

By Butters S. E, Deslandes J. V

The selection of loading and haulage equipment in a proposed or oper- ating mine is vital in ensuring the cost effective achievement of produc- tion targets. To assist in the evaluation of different haulage systems, a truck haulage simulation model has been developed at BHP Melbourne Research Laboratories. The operation of the model is described and exam- ples of an actual application at Mt. Whaleback Mine is presented.

Jan 1, 1989

Nickel ores from three different mines, Digger Rocks, Cosmic Boy and Flying Fox, are treated at the Forrestania concentration plant. The ore types vary from oxidised supergene ores to primary pyrrhotite+pentlandite ores. Mineralogical investigations on the ore and process samples have been carried out in different stages of process development. One of the studies was done with the samples collected from the flotation circuit in 19 June 1994 when the Cosmic Boy ore was processed. The process products were screened, and the size fractions were analysed for the main elements by appropriate analytical methods. Mineralogy of the products was studied microscopically and composition of the sulphides was analysed with an electron microprobe. Liberation of the main sulphides in the flotation feed was determined with the point-counting method, and weight percentages of the minerals were calculated using chemical and mineralogical data. The typical sulphide assemblage of the Cosmic Boy ore is violarite, pentlandite, pyrite, pyrrhotite and chalcopyrite. Violarite dominates over pentlandite (ratio being 70 per cent to 30 per cent), and pyrrhotite is strongly replaced with pyrite and magnetite. One of the most common mineralogical features of this ore type is secondary magnetite, which occurs as narrow rims in porous violarite or in association with secondary pyrite. Serpentine, talc and chlorite are the main gangue minerals. In the milled feed (76 per cent -74 ¦m) locked particles between nickel and iron sulphides are common. About 41 per cent of total pentlandite occurs as pure liberated particles, and 33 per cent as locked grains with violarite. Liberation degree of violarite is 55 per cent, and the most common type of locked particles is violarite+magnetite, carrying about 20 per cent of total violarite. To achieve a recovery of 80 per cent for pentlandite, all the particles containing at least 50 vol-% pentlandite should be floated into the nickel concentrate. Correspondingly recovery of 80 per cent can be reached for violarite if all the particles containing at least 65 vol-% violarite are floated.

Jan 1, 1996

By Johnstone RD, Rattenbury MS

RACE Quartz-calcite veins containing Au, As, W, Cu, Pb, Zn and Fe cross-cut Alpine Fault- related structures in the Alpine Schist of South Island, New Zealand. These veins, and some other related veins have been deposited by metamorphic fluids at 250¦C to >320¦C at pressures of a few hundred bars. The fluids were very variable in composition, with 0 to 50 mole % CO2 and 2 to 18 wt. % NaCl equivalent. Penetration of hot metamorphic fluids to shallow levels in the crust was facilitated by rapid uplift of hot rocks at a compressive plate margin. Fluid immiscibility at shallow levels caused concentration of salts and metals into the aqueous phase. Gold precipitation was caused by reduction by pelitic country rock and/nr dluILion by other aqueous fluids.

Jan 1, 1987

By R Loweth

The application of discreet event simulation has matured in modelling manufacturing systems for production analysis. This simulation tool was used in studying a number of mining operations, especially material handling processes. The study of truck-shovel operation including equipment matching, selection, and production estimation utilised the discrete event simulation for providing valuable decision-making information. The sophistication of the available simulation tools grew over times, and simulation driven animation was used to facilitate the validation and visualisation of the simulated system. This form of visualisation enhanced the simulation use greatly. First of all, it provided a communication medium to transfer information to the non-technical managerial personnel as a better decision-making tool. Moreover, the animated visualisation provided a validation tool to check the working of the simulated system and interaction among its components.

Jan 1, 2003

By S Porter

The Melbourne City Link Project is a privately funded road infrastructure project linking three significant existing freeways in the vicinity of the Central Business District. The State Government, through the Melbourne City Link Authority, has contracted Transurban to build, own and operate City Link for a concession period of 34 years before the road network is transferred to the State. Transurban has a contract with Transfield Obayashi Joint Venture (TOJV) to design and construct the works. The project is divided into the southern and western sections and the tunnel works comprised the significant component of the Southern Link. Outside of the cut and cover tunnels at the portals, the driven tunnels component was constructed by TOJV direct labour. TOJV subcontracted all design work to a joint venture of Hyder Consulting and CMPS&F (Hyder/CMP). The geology in the tunnel corridor and generally below the city of Melbourne is highly variable and constantly changing. The tunnels were driven, for the most part, in siltstone and sandstone of the Silurian age, but also intersected overlying basalts and clays. The Silurian bedrock is a fractured aquifer that is connected to overlying alluvial aquifers. Consequently, the construction of the tunnels was a complex engineering task. This paper details the operational relationships and procedures developed to deliver a design that was aligned to the construction constraints and delivered an end product that met all technical, quality, cost and program goals.

Jan 1, 1999

Maps of mineral grade used to assess mineral reserves are most commonly generated using one of the many estimation methods available such as inverse distance weighting or ordinary kriging. Most such maps incorporate a degree of spatial smoothing which is an integral part of the averaging process. In deposits with highly variable grade which include many gold deposits, this smoothing can mask the detailed geometry of the mineralization at the economic cutoff grades being considered. In underground mining, a knowledge of this geometry is important in the choice of mining method and thus in the assessment of the minable reserves.The method of conditional simulation in geostatistics can be used to generate maps of grade which reflect the actual spatial variability of grade as measured through the variograms of the drill hole data. Simulated maps can provide a number of equiprobable images of the mineralization geometry from which a more appropriate mining model of the mineralization can be developed. Multiple simulations can also be used to assess the uncertainty existing in the current knowledge of the reserves.

Jan 1, 1990

By Brinkmann J. R

The relative effects of the two basic mechanisms contributing to rock breakage during blasting, shock and gas penetration, are neither well understood nor well characterized, and need further clarification. Blasthole liner (BHL) tests separate the two effects, and by enabling direct measurement of borehole expansion give insight into the shock/gas energy partitioning in rock confinement. The hydrodynamic code DYNA2D is used to simulate the shock effect of the detonation of emulsion in a stainless steel lined hole, and the predicted expansion is compared with experiment. Workers in the past have neglected near-blasthole phenomena and have calibrated models based on stress measurements remote from the blasthole. Extrapolation back to the blasthole has inherent limitations, and indeed, one of the deficiencies of these models is that they have not been able to predict correct borehole expansions, as observed in BHL experiments. DYNA2D has been enhanced by the ICI group with a detonation model which resolves the explosive reaction zone. As a preliminary step towards the ultimate goal of devising a practical damage model, simulations are used to predict the maximum expansion that would take place if the rock were to remain undamaged. Various material parameters are investigated and it is shown that calculated liner expansions are appreciably lower than measured values for high rock yield strengths, while greater than values for low yield strengths.

Jan 1, 1990

By Gottlieb P, Sutherland DN

The paper describes a method of making quantitative mineralogical measurements on many of the major lead/zinc orebodies in Australia. The work was done using QEM*SEM. It was found that a relationship betwen phase-specific surface area and particle size, when plotted in a suitable way, gave a straight line with slope related to the grain size of the mineral in question. The method provides an excellent way of differen- tiating between minerals in existing orebodies and, consequently, an easy way to establish a comparison between a new prospect or orezone and current operations.

Jan 1, 1988

By Hart A. T, Lanigan P. G

BHP is currently undertaking research into plasma are metallurgical processing at the Central Research Laboratories (CRL), Shortland. The use of high intensity plasma arcs for melting and smelting has a number of advantages, including; the ability to control atmosphere and furnace operating conditions, total enclosure, high temperatures, versatility, and low in-process inventory in a compact system. The intensive conditions, achievable in a plasma furnace system, make it particularly useful for the smelting and melting of difficult-to-treat materials, such as ore and metallic fines and refractory ores. Two transferred arc plasma smelting furnaces have been set up at CRL; a 100kg furnace is used for small scale melting and smelting studies and a 1 tonne furnace for pilot scale plasma processing studies and equipment development. Power is supplied by a 1MW GEC thyristor DC power supply. A 220kW DC power supply is available for "off site" pilot process trials and demonstrations, and a 150kW non-transfered are plasma torch is also available for other studies. The facility has been designed to allow maximum flexibility in researching and developing applications in metallurgical processing and transferring developed technology to company operations. The objectives behind the development of the facility, details of the facility and an outline of current research areas will be Discussed.

Jan 1, 1987

Australasian mining companies expect a high standard of professionalism from their metals exploration teams. They also have, increasingly, a global perspective, employing explorationists of diverse cultural backgrounds and operating in diverse environments. Human resource development (HRD) of these professional explorationists needs to address all personal facets of functioning independently and interdependently in a modem working culture, as well as the needed technical competency. Creation of a learning organisation to promote this development is critical. Organisational consultants can support managers and supervisors as mentors facing the wide spectrum of development required by the explorationists; mentorship and guidance counselling can then complement training in the maturing of professionals from technical competence to professional independence and interdependence. Empowerment and clearly stated expectations are keys by which professionals can learn efficiently and effectively.

Jan 1, 1996

By Gadsden R. W

Physical and chemical requirements are defined for coke and ferrous materials used in modern high productivity blast furnaces operating in Australian conditions. Recent developments in the type of equipment required to be installed at the steelworks to ensure these requirements are described with illustrations from current plant practice provided.

Jan 1, 1976

The problem of manufacturing from sulphuric 'acid and Christmas Igland "A" phosphate, superphosphate of acceptable physical condition and agronomic phosphate availability, is directly related- to the crystallisation of a reac- tion product, monocalcium phosphate monohydrate. Two solutions to the problem, vacuum drying the superphosphate and calcination of the ore before reaction with acid, are discussed.

Jan 1, 1971

By Molloy GR, Eaton RA

The crusher development programme for 7ft Super Extra Heavy Duty (SXHD) Symons cone crushers commenced in 1984. The main objective of the programme was to run the crushers at maxi- mum power for the full life of the liners. This would give a finer product sizing enabling grinding and flotation plant throughput to be maximised. The study was conducted along two basic lines of attack, the first main- taining an effective profile through the life of the liners, the second improv- ing the properties of the liners. It has been found that crusher liner life can be extended and crushing efficiency improved by modification of liner composition and profile.

Jan 1, 1988

By Sheng X. L

The Jurassic coals at Datong are characterised by their strong, massive sandstone and conglomerate roofs which fail suddenly over large areas, crushing pillars and creating destructive windblasts. collapsed areas have exceeded 180,000m2 and windblasts have extended over one km underground and 200m on the surface and have been accompanied by subsidence troughs on the surface. Scientific analysis has researched premonitory signs of caving and the nature of windblasts leading to considerations of alternative mining methods and ways of dissipating the energy of windblasts to reduce their damage and danger..

Jan 1, 1992

Any engineering firm hoping to do business in the modern world must understand-and take into account-the social and economic realities of client, country, culture, and community. If these considerations are ignored, any large-scale international development project is doomed to failure even before it begins. In this changing world, the distinctions between `developed', `developing', and `less developed' nations are more and more blurred. The so-called `less-developed' and `developing' nations are rapidly acquiring technology, an educated man- agerial and technical class, manufacturing capa- bilities, a growing spectrum of developed financial and raw materials resources, and a broad range of labour skills. These nations are establishing themselves as an integral part of the modern world, on an equal footing with other nations and with justifiable expectations for an ever higher standard of living and an ever better quality of Life.

Jan 1, 1978

The paper describes the reasons for developing, specifically in South Africa, dense medium processes to allow baths to operate at low (about 1,35) and high (about 2,0) cut points. Low density processing was developed to meet the demand for low ash coals; high density processing was developed to enable heavily contaminated raw coals, destined to be burned in captive power stations, to be de-shaled without loss of combustibles. The anticipated and actual technical difficulties of operating baths at such density extremes are described, and the results from operating plants outlined.

Jan 1, 1987

By Bangerter PJ

The use of gravity concentration is, and has always been, the conventional primary method for gold recovery from alluvial deposits. The development of high capacity cone concentrators and metallurgically efficient wash-waterless spiral separators has had some impact in the technology for alluvial gold processing, but perhaps more significantly has led to the relatively recent use of this gravity concentration technology in grinding circuits of hard rock ore for "coarse" gold removal and for scavenging gold locked in sulphides from cyanidation tailings streams.Gravity concentration systems are relatively low-cost, non-polluting and energy efficient; and their judicial use in gold treatment plants can significantly reduce overall capital and operating costs.The application of modern gravity concentration technology to hard-rock and alluvial gold ore treatment is discussed. Flowsheets and test and operating data from a number of gold processing operations incorporating gravity concentration treatment are presented.

Jan 1, 1984

The comparison of belt drives with other types of power transmission involves the consideration of many factors before a final choice is made. Where other forms of power transmission might also be suitable, the selection of the correct type of belt has first to be made, in order to obtain a true comparison. The paper first deals with the types of belting available, followed by a description of most other forms of transmission equipment. An example is then given of the selection of suitable belts, which are then compared with other types of transmission. Comparative costs are also given. Reference charts provided show drives found suitable in general practice...

Jan 1, 1964