Search Documents

By J. O. Betterton, W. M. Spicer

The solubilities of antimony in the a and ß-forms of zirconium were determined between 750" and 1300°C. The a-phase forms by a peritectoid reaction, and the a/(a + ß) and ß/(a + ß) phase boundaries rise in temperature with in- ' creasing antimony. Impurities in the 99.95 pct zirconium were sufficient to influence the phase boundaries and the variation reported is approximate. The restricted solid solubility of the terminal zirconium phases, which is especially characteristic of this system, is thought to result from the low free energy of the Zr2Sb phase. ZIRCONIUM-antimony alloys are important in zirconium alloying studies since antimony is one of the highest valent elements which can be used to make zirconium alloys. The dilute alloys are of further interest as they have somewhat better corrosion resistance' than pure zirconium. The first investigation of the phase diagram was made by Russi and wilhelm2 who found a eutectic reaction, liquid (- 17.5 at. pct Sb) = ß zirconium (- 11 at. pct Sb) + Zr2Sb, at 1430°C'. The Zr2Sb phase was of complicated hexagonal structure, and by thermal analyses of the relatively impure alloys then available, Russi and Wilhelm found evidence for the peritectoid formation of the a-phase. EXPERIMENTAL In the present work, the phase diagram was re-investigated in the region 0 to 5 at. pct Sb and 750" to 1300°C using iodide-zirconium alloys. Details of the procedure have been described earlier. Essentially the alloys were prepared by arc casting and were then examined by the annealing and quenching method. The times of annealing varied from 1 hr at 1300°C to 30 days at 760°C. As in other zirconium phase-diagram studies1"5 the impurities in the zirconium were still sufficient to affect the results, and the experiments will therefore be described in 3 parts. The results from the first 2 parts of the work are shown in Fig. 1. Here the ß/(ß + Zr2Sb) and a/(a + ZrzSb) phase boundaries were determined with alloys made from 99.9 pct zirconium,* and cast under such conditions that the Vickers hardness of a alloys extrapolated to 95 to 110 VPN at 0 at. pct Sb. Such alloys were not suitable for investigations of the (a + ß) region, and the results shown in Fig. 1 near the (a+ ß) and (a +ß + Zr2Sb) regions were determined with purer alloys. These alloys had an extrapolated hardness range of 75 to 85 VPN and were made from 99.95 pct zirconium. A deviation from binary equilibrium occurs in Fig. 1 as indicated by the (a + ß) region of pure

Jan 1, 1959

By John V. Beall

Copper production in the. United States in 1972 amounted to 1,658,000 tons according to the USBM. This figure is up over 1971 but falls below 1970 production of 1,719,101 tons. This report is essentially about the status of copper mining operations in the U.S. and is an update and expansion of the report "Southwest Copper-A Position Survey" published in [A=], October 1965. At that time, the trend was toward using larger equipment to mine lower grade ore and toward the expansion of dump leaching practice. That trend continues today but, it is overlain by intensive activity to comply with existing environ¬mental legislation and uncertainty over proposed revisions of venerable laws governing mining. In the U.S. today there is, practically speaking, no excess smelting capacity so that expansion of copper production through the startup of new mines is inhibited. Owners of a large undeveloped orebody would have to decide before going into production whether to sell the concentrates offshore, which has many problems, whether to try one of several unproved chemical processes for producing refined metal from concentrates or embarking on the construction of a traditional pyrometallurgical plant in the face of considerable uncertainty over the pollution standards that eventually must be met. The situation is such that not only is the present rate of U.S. copper production threatened but the ability to meet projected increased demand in the years ahead may have been severely retarded.

Jan 4, 1973

By Francis T. Havard

A Reply to the Discussion by Mr. Francis T. Havard of the Paper by Mr. Henry W. Edwards, which was read at the Atlantic City Meeting, February, 1.904. (Annual Meeting, February, 1905.) MR. HENRY W. EDWARDS, Grand Junction, Colo. (communication to the Secretary) :* Effect of Heat. It should be remembered that the coefficient of expansion of concrete is nearly that of iron; therefore in constructing flues the design must take account of this important detail. The cracking of flues, mentioned by Mr. Havard as having occurred at a temperature of 100° C. and above, . were possibly caused by neglecting to appreciate the extent of the expansion and contraction of the concrete. Effect of Atmospheric Moisture.-The moisture present in the atmosphere is exceedingly injurious to flues of any material, and those made of concrete are no more susceptible than of brick. My experience with flues of the Monier construction, having walls from 1.5 to 2.5 in. thick plastered upon a net-work of iron rods, was unsatisfactory from the standpoint of dura¬bility.

Mar 1, 1905

By Rich Akerman

as 1866, I wish to assure both these gentlemen that I had not seen the section when I designed mine, :md even if I had, I should not have then dared to put it forth as a standard for English rail makers; tind the soundness of my opinion has a simple but conclusive proof in the statement made concerning the extra price which was at that time required for their production. I need not say that I highly approve of the original Welch section, for it is in principle similar to the design which I made ufteen yeam subsequently; and from a professional point of view I would fully concecle to Mr. Welch the credit of first designing the modern steel-rail section. From com- mercial, matter of tict, and practical point of view, he was, however, before his time by many years; or to put it in another way, rail making was ten years behind its time when the new metal steel was first introduced for rails. If his design has been incorrectly identified with my name (as the sections are similar in principle, though they differ in thickness of flange and web), I beg to say (1st) that I much regret the misun- Understanding which has arisen through no fault of niine, aud (2d) that no confusion has been intentionally created by me. It is a pity that the section designed so long ago has not been made public at an earlier date, as it would make a really goal stand- and pattern, anil even now be quite equal to present requirements. In conclusion, I wish to say that I have never desired to claim any invention or novelty by the publication of my sections; they Were put forth as being such as English railmakers could and would produce at the ordinary market. price, and as being the best and most suitable to be so obtained. Had Mr. Welch or Mr. Holley put forward theirs ten or fifteen years ago, I should have been the first to recommend theru. In fact I should have been glad to see their narnes associated with rail patterns in their own country, in the same way as mine has been. PROFESSOR RICH. AKERMAN, STOCKHOLM, SWEDEN: i AGREE with your (Mr. Sandberg's) views that it is too early yet to stipulate only one definite chemical composition in the rails. Such a stipulation, I think, might he justified, if it were not for the manganese; but this metal changes the properties of the iron aud steel in tho same direc- tion ae carbon, silicon. and phosphorus, by increasing its tensile strength, stiffness, hardness, and brittleaess. If the iron and steel does not only contain carbon and manganese but also phosphorus,

Jan 1, 1881

By Fred S. Mulock

THE principal operating and producing properties covered by the Western Operations of the United States Smelting Refining and Mining Company are the U. S. and Lark mine in the Bingham district of Utah, the Bayard department in the Central mining district of New Mexico, the Midvale mill and smelter near Salt Lake City, the lead refinery of its subsidiary, U. S. S. Lead Refinery, Inc., at East Chicago, Ind., and the coal operations of its subsidiary, United States Fuel Company, at Hiawatha, Utah. Operations of lesser importance at this time are conducted either on company account or by lessees in the Centennial, Bullion Beck, and Eagle and Blue Bell mines in the Tintic district of Utah, the Hidden Treasure and Ophir mines in the Ophir district of Utah, and the White Knob mine in Custer County, Idaho. The Richmond-Eureka Mining Company, in which the Company owns a controlling interest, has leased its properties near Eureka, Nev., to the Eureka Corporation Limited. The Gold-road property at Goldroad, Ariz., has been shut down since 1942, and due to high costs of labor and supplies, consideration is now being given to removal of all surface and underground improvements. The mine and mill im¬provements at the Sunnyside property in Colorado, recently purchased by the Sunbank Corporation, a subsidiary of the Company, are now being dismantled.

Jan 1, 1948

By D. Mills, G. B. Craig

The defortnaliotz of zirconicltt single crystals conlaining osygen in the range 740 to 6800 atom parts per nilllion was esanined oc7er the range 77" to 950°K. An anctlsis of the dqfarmaliotz parameters leads to the cotcllsiotr that the rale -cotzfrolling thermally activated dqivr,irrtion process oe-r /he range 77" to 560°K is oc.crco,ling osvgen alotns. A thermally actitaled defor,ilntion process is not found between 600" and 800", but does occur aboz%e 800°K. THE present investigation was undertaken to measure the effects of controlled amounts of oxygen on the deformation parameters of a zirconium single crystals over the temperature range 77" to 950°K and to determine the rate-controlling mechanisms. Although there is no doubt that the mechanical properties of the group IV metals, titanium, zirconium, and hafnium, are strongly influenced by the interstitial impurities oxygen, nitrogen, carbon, and hydrogen, there are many conflicting theories as to the role played by the interstitials during the deformation proess.'- There is general agreement that the mechanisms which control plastic flow in a metal impose characteristic values on such parameters as the flow stress and its temperature dependence, the activation volume, and the activation energies. These parameters will be used to analyze the deformation mechanisms. eltham,' Sargent,16 and ibbs' have shown that the stress relaxation technique allows the activation volume characteristic of the deformation process to be found during the course of a simple tension test. In many cases it is found that the relaxation of stress is logarithmic with time and obeys a relationship of the following form: T-T = AT =S logl0(qt + C) [I] where t, is the shear stress at the start of the relaxation test, t is the shear stress at time t, and S. q, and C are experimental constants, and S is the strain rate sensitivity of the stress t as shown in the appendix. The slope found from a semilogarithmic plot of At vs time is approximately equal to S. The activation volume u, association with the deformation process, is found from the following relationship: The theoretical treatment of thermally activated plastic flow due to schoeck18 shows that the activation volume when combined with the temperature dependence of the flow stress gives the activation energy for the process according to equations: seegerZ3 considers that the flow stress at lower temperatures ld is composed of two parts such that Tapplied = tinternal + Teffective , where Teffective 3 ff , is the stress necessary to overcome the local obstacles to deformation and Tinternal, ri, is the stress necessary to overcome the long-range elastic stress field of dislocations on other planes. ri is considered to be largely elastic in origin and can be estimated from the stress value at the temperature independent portion of the flow stress-temperature curve. EXPERIMENTAL The crystal bar zirconium used in this investigation was supplied by Wah Chang Corp. whose certified analysis gave the following impurity contents in parts per million by weight: oxygen, 150; nitrogen, 10; iron, 180. All others were less than 100 ppm. The oxygen and iron contents were confirmed by neutron activation and chemical analyses, respectively. Single crystals were grown in an electron beam furnace according to the method of Wilson and Pickle-simer'' and ills.'' The orientation of the crystals was such that the specimen axes were located in the lower third of the standard section of the basal plane stereographic projection for zirconium. This orienta-

Jan 1, 1969

By Harold Margolin

The Ti-Al system certainly merits the investigative attention it has been receiving and this latest contribution by Blackburn is therefore to be welcomed. The titanium-rich end of the phase diagram shown here, as well as the diagram by crossley,17 Clark et a1.,18 and Tsujimoto and Adachi,29 reveal no other intermediate phase than Ti3A1, although a previous work by Ence and Margolin20 had reported an additional intermediate phase. Since then, Buerger Precession pictures of single crystals of 10.5, 11.5, and 12.5 wt pct A1 were made at New York university21 and the extinctions were found to be typical of a D6h a Ti structure. Some superlat-tice spots and/or streaks suggesting the presence of an Mg3Cd structure, i.e., Ti3Al, were also found. Since these specimens had been quenched from the y region20 and had revealed a Ti, it was concludedz1 that y does not exist and the structures interpreted as m + y could not be so considered. The absence of normal two-phase behavior in these structures had been indicated in the paper. Accordingly, the two-phase region y + 6 becomes a + Ti3Al and there is some agreement between the results of Blackburn and of Ence and Margolin20 as to both shape and existence above 900°C of an a + Ti3Al field. Crossley 17 proposed that Ti3Al is a line compound which decomposes congruently at 900°C. It is difficult to discount entirely the fact that clear two-phase structures, varying in amount with position in the two-phase field, could be detected above 900°C by Ence and Margolin.20 Precipitation during quenching could not have been so regular and the twin-phase syndrome17 does not apply. The heat treatment and quenching technique was essentially the same as was used by Crossley, whereas Blackburn, who used a rapid quenching procedure, also showed a two-phase a + Ti3A1 field above 900°C. If the two-phase field exists above 900° C, it is easy to picture a two-phase field which could account for the data of Crossley below 900°C without invoking a line compound existence of Ti3A1. All that would be necessary would be an 0 + Ti3Al/Ti3Al boundary which curved sharply to higher aluminum contents below 900° C. It is clear that the controversy must be solved by techniques which obtain data at elevated temperatures without quenching. It is conceivable that the difference in width of the a + Ti3N fields reported by Blackburn and by Ence and Margolin is due to the longer annealing times used by the latter investigators. The criterion for establishment of equilibrium in our work20 was the

Jan 1, 1969

By A. S. Venkatadri, H. B. Bell

The equilibrium sulfur distribution between molten iron and Ca0-Mg0-Al203 slags containing iron oxide was investigated at 1550°C. The results were used to derive the iron oxide activities at low iron oxide concentrations in the slag by combining the sulfide capacity data obtained from gas-slag work with the free energies of both the sulfur solution in iron and the iron oxide formation in slag. The derived ferrous oxide activities were compared with values based on Tem-kin's kin's and Flood's ionic models. One difficulty in using these models is that the nature of the aluminate ion in slag is uncertain. Nevertheless, such indirect methods, in particular, those described in the present paper, are of value because of the difficulty of measuring small amounts of oxygen in liquid iron in equilibrium with slag. It is shown that these methods confirm the consistency of thermodynamics data on liquid iron and slags. It is well established that decreasing the iron oxide activity in the slag increases the desulfurization of molten iron at constant slag basicity. This effect is most pronounced at the very low iron oxide activities, characteristic of blast furnace slags. Yet a precise quantitative determination of the significance of low iron oxide contents in slag in blast furnace desulfuri-zation is not possible for the following reasons: a) difficulty of separation of iron "shots" from the slag, and b) errors in chemical analysis of small amounts of iron oxide in slags. In view of these obstacles, one must resort to indirect methods of calculating iron oxide activities. EXPERIMENTAL TECHNIQUE The apparatus for providing the sulfur equilibrium data has been described previously1 and was similar to that used by ell' in connection with the study of slag-metal manganese equilibrium. The procedure consisted of: a) melting about 50 g of Armco iron in a magnesia crucible in a platinum furnace, b) adding a mixture of about 15 g of lime-alumina slag and varying amounts of Fe2O3 and CaS, and c) maintaining the temperature at 1550°C for more than an hour in an atmosphere of argon to enable the sulfur equilibrium to be attained. Several melts were made using lime-alumina slags with basic composition 55, 50, and 45 pct lime. During the experiment the temperature was controlled manually using a Pt/10 pet Rh-Pt thermocouple. After the experiment, the Power was shut off and the flow rate of argon was increased to freeze the melt as quickly as possible. The analysis of sulfur in the metal was carried out by the oxygen combustion method3 using uniform drillings from the top and bottom of the metal button. After crushing and grinding and removal of any iron particles with the aid of a hand magnet, the slag was analyzed for sulfur by the CO2 combustion method.4 The E.D.T.A. method was employed for the analysis of lime5,6 and magnesia,= the ceric sulfate method7 for the analysis of slag iron oxide, and the perchloric acid dehydration method5 for the analysis of silica. The remaining amount was taken to be Al2O3 precipitation with ammonium hydroxide in several preliminary melts had confirmed the propriety of using this simple procedure. RESULTS The activity of iron oxide in binary, ternary, and more complex slags has been the object of numerous investigations, and the two experimental methods for its determination are: 1) Equilibrating the metal with the slag in question and measuring the oxygen content of the metal. The ferrous oxide activity is then given by aFeO L%OJSat where [%0]sat is the oxygen content of the metal in equilibrium with pure iron oxide slag. This method was used by Chipman et al.8,9 2) Equilibrating the slag in iron crucibles with known partial pressures of H2/H2O or CO/CO2 mix-tures.10-12 This method is limited to temperatures between 1265" and 1500°C. The very low oxygen content of the melts in this investigation made it impossible to derive the ferrous oxide activity by the first of these methods. Therefore, the iron oxide activities were computed by means of: Sulfide capacity data from the gas-slag work" Temkin's concept14 Flood's approach15 a FeO from Sulfide Capacity. The method of calculating the aFeO involves the sulfide capacity of the slag (c,), the sulfur distribution coefficient (Ls), the free energy of dissolution of sulfur in iron, and the free energy of formation of iron oxide in the slag. Bell and Kalyanram13 have investigated the sulfur absorption characteristics of lime-alumina slags containing magnesia by the Carter-Macfarlane method16 (based on comparing the sulfide capacity of the slag in question with that of a standard slag of unit lime activity) and have derived lime activity values. The relation between sulfide capacity and their lime activity a'CaO is given by: Cs= 3—: Xa'CaO at 1500°C

Jan 1, 1970

By Franz R. Dykstra

DEFINITIONS The ores of iron are classified in three general categories: direct shipping, concentrates, and agglomerated-i.e., pelletized or sintered. Direct Shipping As the name implies, direct-shipping ores are shipped as mined or, perhaps, after screening. Generally, direct-shipping ores are hematitic (R203), magnetitic (R304), or limonitic (2Fe2O3.3H20) in nature. Grades of direct-shipping ores vary widely. Prices are frequently related to the historical Mesabi standard of 51.5% iron, although certain premium lump ores may contain up to 68% iron. The use of direct-shipping ores is diminishing as the advantages of beneficiated ores become evident and reserves are depleted. Concentrates Where the nature of the deposit and economics allows, certain ores are upgraded. This may include no more than washing and screening, or may be as elaborate as fine grinding followed by magnetic, gravity, or even flotation procedures for separation. Coarser concentrates may be smelted "as is.'; Fine concentrates usually are sold as sinter feed. (Sinter, as used here and in the following, refers to a process by which a fine ore-carbon mixture is agglomerated at elevated temperatures on a direct-fired moving grate to eliminate fines and improve chemical and physical homogeneity.) Agglomerates-Pellets or Sinter The development of economic techniques of mining and concentrating taconite (fine-grained, ferruginous jasperoids) led to the introduction of the iron-ore pellet, which is now becoming the major form in which iron is introduced into the furnace. The tremendous reserves of magnetic taconites of the northern United States and Canadian Precambrian shield had been recognized for many years. A century of mining has seen the reserves of the direct-shipping or "red ores" of the Minnesota, Michigan, and Wisconsin ranges approach depletion. Research started in the 1930s has seen the evolution of motives and techniques to concentrate these stubborn refractory ores. The efficacy of concentrate pellets in iron-making has been such as to induce mines throughout the world to grind, concentrate, and pelletize otherwise shipping-grade ores. Table 14.1A.1 shows typical analyses of iron ore. Marketing-Prices of iron may be quoted on a value per long-ton (2240 lbs) or metric-ton (1000 kg or 2204 lb) basis, or on a value per long-ton-unit or metric-ton-unit basis. One iron unit represents 1 % of contained iron per ton. (Thus, a price of $0.45 per iron unit for ore containing

Jan 1, 1976

By Paul A. Schafer

BALATOC mine, the principal gold-producing mine in the Philippines, is 10 miles southeast of Baguio, in the Cordillera Central of northern Luzon.1 The region is a deeply dissected plateau, ranging in altitude from 3000 t0 5000 ft. above sea level. The rocks consist chiefly of granodiorite, diorite, and remnants of metamorphosed sediments, cut by dikes of andesite porphyry and quartz-diorite porphyry. All are intruded by a volcanic breccia plug, oval in horizontal section, about 3200 ft. long and 2300 ft. wide, which is the north central part of the mineralized area. Three main vein systems have been developed (Fig. 1): q6, 231 and 364, which strike about N.70°E. and dip 5o to 90°S. Each system is a braided zone consisting of many individual components. They are disturbed by a series of premineral faults or shear zones striking about N.45°E. Twelve of these produce important effects on the persistence, character, and quality of veins. From west to east the faults are named (after claims): Hog, Big Gun, Bull, Pine, Lolita, Bar No. I, Bar No. 2, Curt, Sun, Helen, Itoe, and Frog. They are early breaks formed prior to the N.70°E. vein fractures. Mineralization occurs on them but, with several prominent exceptions, they are too low grade to mine. A number of northwesterly striking faults complete the structural pattern. Although they are relatively abundant, the effect on the veins is so small that they do not present any problems in mining or development. All of these faults that have been observed are later than the N.70°E. veins and offset them to the left. NORTHEAST FAULTS The early northeast faults* are notably continuous in spite of their small displacements, 20 to 100 ft. Frequently they appear so weak that their importance is masked and their identity clouded. The gouge along any of these faults may vary from exceedingly weak at one point to very strong at another point only a short distance away. In other words, the amount of gouge depends on the changes of attitude of the fault plane, and is no indication of the extent of the movement. Places where walls are spread apart are filled with gouge squeezed from tight places. Also, mineralization sometimes obscures fault gouges by replacement. The mineralization of northeast faults has produced several important ore bodies; namely, 231 west on Pine fault and q6 vein on the same fault. To a smaller extent, Lolita, Curt, Bull, Bar No. I, and Sun

Jan 1, 1942

By D. R. Miller

Internal friction and elastic modulus variations in electrorefined titanium, iodide refined titanium, and alloys of the latter material with oxygen, nitrogen, aluminum, and zirconium were investigated. No oxygen peak was detected with electrorefined titanium but, provided precautions were taken to prevent increases in background damping, an oxygen peak at about 410°C could be resolved with each of the other materials. An additional partially resolved peak was observed at 500°C in a Ti-N alloy. An anomaly in the variation of rigidity modulus with temperature was observed. Possible mechanisms for the formation of any oxygen peak have been discussed. PRATT, Bratina, and Chalmersl investigated the internal friction of commercial purity titanium and alloys of this material containing 1.5, 3.5, and 4.5 at. pct O. With commercial titanium the internal friction curve consisted of two components, a background which increased steadily with temperature and a peak at about 600" C which was due to grain boundary relaxation. In the Ti-O alloys, however, an additional internal friction peak was observed at 430" to 450°C and, since this peak increased in height as the oxygen content was increased, it was thought to be associated with the presence of oxygen. The diffusion of oxygen in titanium at temperatures between 300" and 500° C is believed to have marked effects in its tensile properties2'3 and the present internal friction measurements were undertaken to obtain further information on this diffusion, using material of higher purity than that of Pratt et d. and an apparatus of very much greater sensitivity. In the course of the investigation a number of important limitations on the work of Pratt et al. were revealed and results have been obtained which emphasize the need for ensuring that in this type of experiment, internal friction is independent of strain amplitude and that the values obtained are reproducible. 1) MATERIALS AND APPARATUS The basis material from which the majority of the specimens was prepared was iodide-refined titanium, the major impurities in which were oxygen and nitrogen—the metallic impurities being present at concentrations less than 0.001 at. pct. The hardness of this material after arc melting, forging, and swaging to rods 1/4 in. diameter was Dph = 110. Specimens 10 in. long and 0.020 in. (0.51 mm) diameter were prepared from these rods by further swaging and wire drawing and were finally annealed in vacuo (5 x 10-6 mmHg) for 24 hr at 800°C. The oxygen alloys were prepared from iodide-

Jan 1, 1962

By James O. Elton

This paper covers, besides laboratory work, a study of actual operation at the Washoe Smelter over a considerable period of time, together with the results of a visit to the Midvale plant of the United States Smelting & Refining Co., near Salt Lake. For the latter privilege, as well as permission to publish the resulting data herein given, I am indebted to George W. Heintz, General Manager of the Midvale plant, and here take pleasure in expressing my appreciation for the many courtesies extended to me by Mr. Heintz and members of the technical staff at the smelter. Almost all of the world's supply of arsenic is recovered as a byproduct in the smelting of other metals. It is seen 'on the market in various forms, the most common being arsenic trioxide, the " white arsenic " of commerce, which is sold as a heavy white powder, or in white, glassy, translucent masses. The trioxide is used in the manufacture of pigment, glass, and insecticides. About 50 per cent. of the domestic consumption is supplied by imports. Statistics of Arsenic Trioxide in United States.' Production. Consumption. Price Per Pound. Year. Tons. Tons. Cents. 1907..........1.010 5.471 5 1908,.........1,302 6,098 33/4 1909,.........1,007 4,600 2 7/8 1910,.........1,526 5,428 2 1/2 1911,.........3,081 6,539 2 1912,2........ 2,926 Closed at 4 7/8 Arsenic occurs in combitlation with sulphur and the metals in a large number of minerals. It is present in small amounts in many ores. In the roasting and smelting furnaces many of its compounds break down, liberating arsenic trioxide, which is volatilized and carried by the gases into the flue system, where a part is condensed and settles with the flue dust.

Jan 1, 1914

THE opening session of the Institute was held at the rooms of the American Society of Civil Engineers, No. 4 East 23d Street, Vice-President R. W. Raymond in the chair. After a short introductory address by the chairman, the following names were presented by the Council for election as members and associates of the Institute. They were unanimously elected : MEMBERS. Abbott, James W., - Lake City, Col. Abbott, J. J., Jr., - Lake City, Col. Bartlett, J. C., - Cambridge, Mass. Billings, G. H., - Boston, Mass. Blake, Frank C., - Lafayette College, Easton, Pa. Dewey, Fred. P., - Lafayette College, Easton, Pa. Douglass, Samuel T., - Ann Arbor, Mich. Emmons, S. F., - New York City. Engle, George U., - Philadelphia. Harrington, Dr. Bernard J., - Montreal, Canada. Hayden, Wm. B., - Columbus, O. Hill, Leslie C., - Capelton, Quebec, Canada. Land, W. J., - Atlanta, Ga. May, Wm. A., - Scranton, Pa. Mills, James E., - St. Louis, Mo. Moore, Charles W., - Montezuma, Ind. Page, William Byrd, - Lexington, Ky. Putnam, Douglas, Jr., - Ashland, Ky. Richards, Henry, - Dover, N. J. Roberts, Percival, Jr., - Philadelphia. Sackett, S. G., - Brooklyn, N. Y. Schley, Wm. S., - Atlanta, Ga. Setz, Gustav, - Mine La Motte, Mo. Talbutt, John H., - Lexington, Ky. Torrey, Herbert G., - U. S. Assay Office, New York City. Wernlitz, Fred. W., - Cartersville, Bartow Co., Ga. Wiestling, Geo. B., - Mont Alto, Franklin Co., Pa.

Jan 1, 1877

(Members are urged to send in for this column any notes of interest; concerning themselves or their fellow-members.) Members and guests who called at Institute headquarters during the period Nov. .10, 19 16 to Dec. 1.0, 1916: Chester Atkinson, La Fundicion, Peru. , Paul Llewellyn, East Chicago, Ind. F. J. Brule, Toronto, Ont., Canada. Harry March, London, England. Sterling H. Bunnell, New York, N. Y. E. P. Mathewson, Toronto, Ont., Canada. G. H. Cunningham, Hobart, Tasmania.' E. W. Moore, Budapest, Rumania. Courtenay DeKalb, Tucson, Ariz. W. J. Pentland, Guadalajara, Mex., E. H. Dickenson, New Y.. Heinrich Ries, Ithaca, N. Y. E. B. Durham, Mount Kisco, N. Y. W. E. Saunders, Philadelphia, Pa. L. B. Eames, Pueblo. Colo. J. G. Scrugham, Reno, Nev. N: H. Emmons, 2d, Copperhill, Tens. - W. H, Seagrave, Kennecott, .Alaska. R. E. Hoffman, Hannibal Mo.'s H. B. Small, Magangue, Colombia. B. B. Hood, Chronic, N. J. W. H. Staver, Washington, D. C. H. E. Jackman, Rochester, N. Y. R. K. Stockwell, Santiago, Chile. F. H. Jackson, Joplin, Mo. Warren D. Thompson, Boston, Mass. Knight S. Jordan, Provo. Utah. Thor Warner, Kingman, Ariz. William Kelly, Vulcan, Mich. S. T. Wellman, Cleveland, Ohio. W. H. Lanagan, San Francisco. Cal. F. H. Willcox, Pittsburgh, Pa. H. H. Lauer, Northampton, Pa. Arthur K. Adams has been appointed geologist to the Andes Copper Co.

Jan 1, 1917

PRESIDENTS DAVID THOMAS 1871 R W RAYMOND 1872-1874 A L HOLLEY1875 ABRAM S HEWITT 1876 T STERRY HUNT 1877 ECKLEY B COXE 1878 - 1879 WILLIAM P SHINN 1880 WILLIAM METCALF 1881 RICHARD P ROTHWELL 1882 ROBERY W HUNT 1883 JAMES C, BAYLES 1884-1885 ROBERT H RICHARDS 1886 THOMAS EGLESTON 1887 WILLIAM B POTTER 1888 RICHARD PEARCE 1889 ADAM S HEWITT 1890 JOHN BIRKINBINE 1891-1892

Jan 1, 1923

By A. E. Dwight, Paul A. Beck

Known CsCl-type phases in transition metal alloys are shown to be formed preferentially at an electron concentration of approximately 6; a tetragonally distorted version of the CsCl structure is stable at -e/a = 6.5. The relationship of the distortion to electron concentration is verified by experimental data for the quasibinary systems Time ,Os) , Ti(Re,Ir), and Ti(Re,Pt) and the ternary system Ti-Ru-Rh. It was noted some years ago1j2 that the occurrence of CsC1-type ordered structures in equiatomic binary alloys, AB, of transition metals correlates with the location of the component elements in the periodic table. One of the components, A, must be to the left and the other component. B, must be to the right of the chromium group. It was pointed out2 that the CsCl structure does not occur in CrFe. is metastable in VFe,3 and is stable in TiFe up to high temperatures, and that this progressively increasing stability may correspond to an increase in electron transfer between the two components and to a correlated decrease of the magnetic moment associated with the iron atoms. Such a decrease was in fact later demonstrated by Nevitt. 4 The binary CsC1-type phases that are formed by a transition metal with either another transition metal or a lanthanide are listed in Table I. Thirty-three of these phases occur at an average electron concentration (average number of electrons outside of closed shells) of e/a = 6. The five phases that are formed at an electron concentration of e/a = 5.5 appear to be borderline cases. This is suggested for instance by the fact that TiRe is bcc. without any long-range order, while TiTc (at the same electron concentration) has a CsCl ordered structure. Six of the undistorted CsCl phases formed by transition metals with one another have an average electron concentration of e/a = 6. 5. Table I. With the exception of Zr4,Rhs4 and Hf48Rh52. the B component in these phases is a first long-period transition metal, i.e.. iron or cobalt. TiNi. with an electron concentration of e/n = 7, appears to undergo transformation at around room temperature to a more complex ordered struct~re.~ The five other CsCl structures known to occur at e/a = 6.5 have either scandium or a lanthanide metal as the A component; the difference in the elec-tronegativity and in the e/a ratio between the component elements is in these phases very large, A(e/a) - 7, and they may be expected to have a rather strong ionic bond component. Presumably the ionic bond stabilizes the CsCl-type structure at the equiatomic composition and it overrides the electron concentration requirement. When the B element is not from the first long period and the A component is not a rare earth metal. equiatomic (AB) alloys of transition metals with an average electron concentration of e/a = 6.5 in most cases have a crystal structure closely related to the CsC1-type, but slightly distorted tetragonally, Table I. This was first found6 for VRu, NbRu. and TaRu. It was noted6 that the undistorted CsCl structure is also stable in the three systems. but at a lower electron concentration, near e/a = 6. In these systems this requires a deviation from equiatomic stoichiometry. which is otherwise ideally suited for the CsC1-type structure. A similar situation was later found in the Ti-Rh7 and the Ti-Ir systems. 8 The Ti-Rh alloys undergo a second distortion and become orthorhombic when the rhodium content becomes somewhat larger than 50 pct. As mentioned previously. TiRe does not have the CsC1-type ordered structure. In order to investigate how close TiRe is to the borderline of stability of the

Jan 1, 1970

By James E. Howard

At the request of the Council of the Institute, I have the honor to submit the following remarks upon the Program of Tests under which the current work of the Watertown Arsenal Testing Laboratory is carried on, which comprises, among other items, the tests of steel ingot metal and derivative shapes. The intended scope of the tests may be illustrated by extracts from the descriptive part of the program as submitted by the Laboratory under date of April 17,1907, and subsequently approved by the Chief of Ordnance, U. S. A. Under Item 1, Ingot Metal—Open hearth, acid and basic; Bessemer, acid and basic; crucible; fluid compressed and uncompreesed—descriptive remarks were made as follon-s: "A thorough, fundamental inquiry into the physical properties of steel necessarily begins with the ingot metal. Investigations, having for their object the improvement of steels, should also begin with the ingot. A knowledge of the ingot structure is essential for judging of the subsequent behavior or appearance of the metal. Under ordinary conditions, so little information is obtained from the ingot in individual cases that practically none of importance is acquired. These remarks have particular reference to the state of physical and structural

Jan 1, 1909

By Sherwin F. Kelly

FRONTIERS of geological knowledge retreated further this past year before an ever-widening geophysical attack, as governments and endowed institutions continued to take an increasing practical interest in the geophysical line of approach to the study of earth phenomena. A year ago I opened this annual review with a brief account of the efforts to discover what formations lie concealed beneath the deep sediments which form the superficial portions of the Continental Shelf off the eastern United States. That work was but the beginning, and 1938 saw its continuation and expansion. With the assistance of a Guggenheim Fellowship, Maurice Ewing pushed his researches in the development of instruments and techniques for deep-sea seismic refraction studies. Ewing's early refraction profile from the Virginia Capes to the edge of the Continental Shelf has been followed by a similar traverse in Great Britain from the coast of Cornwall to the edge of the Continental Shelf southwest of England. This showed that the thickness of the sedimentary mantle and the rates of slope of the basement surfaces there are comparable to those in the Virginia Cape district.

Jan 1, 1939

By M. O. Abo-el Fotoh, J. B. Mitchell, J. E. Dorn

The effect of strain rate and temperature on the tensile flow stress of a polycrystalline bcc alloy of magnesium containing 14 wt pct Li and 1.5 wt pct Al was investigated for strain rates of 3.13 x lom5 to 3.13 x 10-3 per sec over the range from 20° to 300°K. From about 180° to 300°K the alloy exhibited an ather-ma1 deformation behavior where the flow stress was independent of strain rate and increased only slightly with decreasing temperature. At lower temperatures the flow stress was strongly strain-rate- and temperature-dependent, characteristic of deformations controlled by thermally activated mechmzisms. The activation volume for thermally activated plastic defornzation was between 5 and 30 cu Burgers vectors, independent of plastic strain. This low-temperature thermally activated deformation behavior was found lo be in satisfactory agreement with the theoretical dictates of the Dorn-Rajnak1 formulation of the Peierls mechanism where deformation is controlled by the rate of nucleation of pairs of dislocation kinks over the Peierls energy barriers. SEVERAL studies of the low-temperature thermally activated deformation of bcc metals and alloys (molybdenum,1 tantalum,1 Fe-2 pct Mn,2 Fe-11 pct MO,3 and AgMg4) have revealed that the strain rate is controlled by the activation of dislocations over the Peierls-Nabarro energy hills. Although there is some uncertainty as to the nature and effect of solute atom-dislocation interactions during low-temperature deformation of bcc metals, it has been concluded by Dorn and Rajnak,1 Conrad,1 and Christian and Masters6 among others that overcoming the Peierls-Nabarro stress which arises from the variations in bond energies of atoms in the dislocation core as it is displaced is the probable mechanism controlling low-temperature deformation. The purpose of this research was to investigate the low-temperature plastic deformation of the bcc alloy Mg-14 wt pct Li-1.5 wt pct A1 to determine if the behavior of this alkali metal alloy might be analogous to that for other bcc metals. This alloy was selected because of its availability and its current industrial importance as a lightweight material for aircraft and aerospace applications. I) EXPERIMENTAL PROCEDURE Polycrystalline tensile specimens having cylindrical gage sections 2 in. long by 0.2 in. in diam were machined from as-received alloy sheet stock of Mg-14 wt pct Li-1.5 wt pct Al. Specimens were annealed in an argon atmosphere at 423°K for 4 hr and maintained in a kerosene bath together with the sheet stock to prevent corrosion. The resulting specimen microstructure consisted of a coarse uniform dispersion of incoherent precipitate MgLi2Al particles7 in a bcc 0 phase matrix having an average grain size of 150 p. Prior to testing the specimens were chemically polished in dilute hydrochloric acid. Comparison of tensile properties and microstructures of specimens cut from center and edge sections of the sheet stock revealed no effects of inhomogeneities in the sheet material. Tensile tests were performed on an Instron machine at crosshead speeds corresponding to tensile strain rates of 1.56 x 10-5 and 1.56 x 10"3 per sec. Stresses were determined to ±2 x 106 dynes per sq cm and strains to within ±0.0001. Average values of shear stress t and shear strain y reported were taken as one half the tensile stress and three halves the tensile strain, respectively. Flow stresses were taken at 0.05 pct strain offset. Test temperatures down to 77°K were obtained by immersing the specimens in constant-temperature baths. Lower-temperature tests were performed in a liquid helium cryostat to within ±2°K of the reported values. Prior to testing at the various temperatures and strain rates all specimens were prestrained at 2 35°K at a shear strain rate of 3.13 x 10-5 per sec to a stress level of 0.606 x 10' dynes per sq cm to obtain a uniform initial state. Additional tests were made to determine the effect of changes in strain rate and strain on the flow stress by rapidly changing the crosshead motion during testing. Shear moduli of elasticity, needed for analyses of the data, were obtained at several temperatures by a common technique of determining the resonant frequencies of vibrations of rectangular test specimens. 11) EXPERIMENTAL RESULTS Fig. 1 shows the experimentally determined flow stress vs temperature for two strain rates. Two distinct regions of behavior are evident. Below about 180°K the strong increase in flow stress with increased strain rate and decreasing temperature indicates that deformation is controlled by a thermally activated dislocation mechanism. At higher temperatures an athermal region is evident where the flow stress is independent of strain rate and only slightly dependent on temperature. The applied stress t to cause plastic flow was separated into two components:

Jan 1, 1969

By Nigel B. Pearson

INTRODUCTION Chingola Division of Nchanga Consolidated Copper Mines Limited is situated in the Copper- belt of Zambia, approximately 30 kilometres south of the border with Zaire. It is the country's leading producer of copper and its principal foreign exchange earner, and has been, in its time, the largest single copper producer in the British Commonwealth and the second largest in the world. There are two 'primary' copper sources at the Division, namely Underground producing approximately 100 000 tonnes of contained copper annually, and the Open Pits, producing approximately 200 000 tonnes annually. Following the commissioning of the Tailings Leach Plant in 1974, treating final tailings, metallurgical recovery increased from approximately 70% to in excess of 80%. Extensive deposits of cobalt are present and following the rise in the market price in 1979 and 1980, plans were made to extract this separately. Cobalt production commenced in 1980 from Underground and will increase substantially when the Open Pit cobalt reserves become available in approximately 2 years time. This paper covers the development of the production method of the principal Underground Orebody, known as the Lower Orebody, and the control systems applied to it. HISTORY The Lower Orebody, formerly known as the Nchanga West Orebody, was discovered by extensive Diamond Drilling operations in the late 1920's. Development of the Shaft complex and the orebody commenced and continued until 1931 when flooding from development on the 480 foot horizon necessitated closure. The mine remained closed until 1937 and production commenced from the Lower Orebody in 1939. Various expansion schemes of the Metallurgical Plants and the Underground workings were completed over the years with the result that Underground production increased steadily to in excess of 150 000 tonnes copper annually in the 1960's. In recent years production has levelled out at slightly less than 100 000 tonnes annually. This decrease is as a result of producing from a lower grade reserve, available within a more limited production front, and the application of production constraints in the light of experience gained. GEOLOGY Within the Nchanga Mining Licence Area of Chingola Division, there are a total of 14 known copper orebodies in the basal part of a thick succession of sediments of Pre-Cambrian age. The sediments rest on a Basement Complex of granites, gneisses and schists. Three superimposed stratiform orebodies, known locally as the Lower, Intermediate and Upper Orebodies, occur over a vertical interval of approximately 150m. Current annual copper production is approximately 300 000 tonnes. The ore originates from four different mining operations, one Underground mine and three Open Pits. Approximately 9 million tonnes of ore grading between 3 and 3.5% copper are milled annually. The two largest sources of ore, the Under- ground mine and the Nchanga Open Pit are on the gently dipping south limb of the Nchanga Syncline (Figure 1). In the Nchanga Open Pit the major source of ore is the Upper Orebody with lesser tonnages from the Intermediate and Lower Orebodies. In the Underground mine the Lower Orebody is the only orebody being mined, underground mining of the Upper Orebody being suspended for economic reasons in 1978. The typical stratigraphic column is illust- rated in the legend on Figure 1. The footwall rocks comprise either Nchanga Red Granite or the Arkose formation, both of which are hard competent rocks, offering generally good mining conditions for footwall development. Copper mineralisation of the Lower Orebody extends from the upper part of the Arkose to the top of the Lower Banded Shales. Overlying the Arkose is the Transition zone (0-18111 in thickness). The Transition zone comprise a lower member, Transitional Arkose, consisting of incoherent kaolinised sandstone, and an upper member, Transitional Lower Banded Shales consisting of normally soft bleached and silicified shale. The soft nature of the Transitional rocks is

Jan 1, 1981