Search Documents

By H. J. Rose, J. J. S. Sebastian

When coal is stored under ordinary conditions, progressive changes take place in its chemical and physical properties. These changes are largely caused by the reaction of atmospheric oxygen with the coal substance. Although this "oxidation" or "weathering" occurs slowly in the case of high-rank coals, it is nevertheless a matter of considerable importance, since even a small amount of oxidation may affect the value of coal for carbonization purposes. Coal storage is a necessity at all carbonizing plants. In normal times there are about 5,000,000 tons in storage at by-product coke ovens and gas retorts in the United States, as compared with an annual throughput of about 75,000,000 tons. In other words, the average coal reserve at such plants is slightly less than one month's supply. However, owing to the cost of storage and recovery, coal is usually left in stockpile for as long a time as the management thinks advisable. Storage for six to eight months is common practice and is, in fact, a necessity at certain plants which obtain their coal by water routes that are closed during winter months. Modern by-product coke ovens operate continuously, and they are not cooled down from the time that they arc put into operation until they are shut down for rebuilding—perhaps 20 years later. This continuous operation is imposed by silica-brick construction and high operating temperatures. It is therefore obvious that coke plants must at all times maintain an adequate supply of stored coal, in order to prevent a failure in supply from any cause whatever. Thus when strikes or other emergencies threaten, abnormally large coal stocks are accumulated and held at coke and gas plants. Many of these plants have been forced, at some time or other, to use coal that has been stored for several years. Such coal may fail to coke at all, or it may produce a dirty appearing, weak coke of reduced value. The yields of salable by-products may also be distinctly lowered. However, it must not be assumed that slight oxidation or heat effects are always injurious. Certain high-volatile coals produce a stronger, blockier

Jan 1, 1930

By John H. G. Monypenny

The range of chromium content of stainless steel is, in most cases, included in the limits 11 to 14 per cent., or the middle part of the range, 9 to 16 per cent., specified by the discoverer. For some time after the steel was produced commercially, the carbon content was about 0.3 to 0.4 per cent. and occasionally higher; only rarely was material with 0.25 per cent. carbon or less produced. The reason for this is obvious from the nature of the alloys of chromium available for making such steels; as the lowest carbon content generally available was about 1 per cent., and this in conjunction with a chromium content of about 60 per cent., the production of a 12-per cent. chromium steel with less than 0.25 to 0.30 per cent. carbon was impossible. The advent, on a reasonable commercial scale, of carbonless ferrochromium has modified this condition, however, so that for the last three years stainless material containing 0.1 per cent. or less carbon and the normal amount of chromium has been on the market. As far as the author is aware, the material was first made on a commercial scale by the firm with which he is associated in June, 1920, when a 5- or 6-ton cast of material containing 0.07 per cent. carbon and 11.7 per cent. chromium was made and cast into 12-in. ingots. The necessity for using a totally different raw material, carbonless ferrochromium, instead of the ordinary low-carbon ferro (0.6 to 1.0 per cent. carbon) has led to the idea that stainless iron is a quite distinct product and quite different from stainless steel. While this may be true from a commercial aspect, it is wrong metallurgically. The name stainless iron is unfortunate as the material is a very mild stainless steel and forms the lowest carbon member of a series of steels of continuously varying content which are, in many respccts, the counterpart of the series of ordinary carbon steels ranging from "dead soft" to tool steels. In an article on stainless steel in the Journal of the Society of Chemical Industry, November, 1920, the author said "Just as in the far-off days 'steel' was regarded as a hard product of iron, and little or no attempt was made to grade it into harder or softer varieties, so at present stainless

Jan 1, 1924

By John H. G. Monypenny

The range of chromium content of stainless steel is, in most cases, included in the limits 11 to 14 per cent., or the middle part of the range, 9 to 16 per cent., specified by the discoverer. For some time after the steel was produced commercially, the carbon content was about 0.3 to 0.4 per cent. and occasionally higher; only rarely was material with 0.25 per cent. carbon or less produced. The reason for this is obvious from the nature of the alloys of chromium available for making such steels; as the lowest carbon content generally available was about 1 per cent., and this in conjunction with a chromium content of about 60 per cent., the production of a 12-per cent. chromium steel with less than 0.25 to 0.30 per cent. carbon was impossible. The advent, on a reasonable commercial scale, of carbonless ferrochromium has modified this condition, however, so that for the last three years stainless material containing 0.1 per cent. or less carbon and the normal amount of chromium has been on the market. As far as the author is aware, the material was first made on a commercial scale by the firm with which he is associated in June, 1920, when a 5- or 6-ton cast of material containing 0.07 per cent. carbon and 11.7 per cent. chromium was made and cast into 12-in. ingots. The necessity for using a totally different raw material, carbonless ferrochromium, instead of the ordinary low-carbon ferro (0.6 to 1.0 per cent. carbon) has led to the idea that stainless iron is a quite distinct product and quite different from stainless steel. While this may be true from a commercial aspect, it is wrong metallurgically. The name stainless iron is unfortunate as the material is a very mild stainless steel and forms the lowest carbon member of a series of steels of continuously varying content which are, in many respccts, the counterpart of the series of ordinary carbon steels ranging from "dead soft" to tool steels. In an article on stainless steel in the Journal of the Society of Chemical Industry, November, 1920, the author said "Just as in the far-off days 'steel' was regarded as a hard product of iron, and little or no attempt was made to grade it into harder or softer varieties, so at present stainless

Jan 1, 1924

By J. R. Mihalisin, J. S. Iwanski

The response of Inconel "700" to heat treatment has been studied by light and electron microscopy combined with X-ray and electron diffraction techniques. A heat treatment which vesults in low ductility for this alloy appears to be associated with the formation of MC carbide in a Widmanstdtten distribution. This type of precipitation can be suppressed by suitable heat treatment with concurrent increase in ductility. Various other phases precipitated in this alloy are also identified. RECENT studies of commercial nickel base su peralloys have demonstrated the importance of the morphology of carbide phases upon physical properties.' For example, empirical heat treatment studies applied to Nimonic "80" and Inconel "X" have resulted in prescribing double aging treatments for optimum physical properties. These treatments have subsequently been related micro-structurally to grain boundary carbide morphology.2 The purpose of this study was to obtain information about the morphology and identity of some of the phases precipitated in Inconel "700" after heat treatment. It was hoped that some correlation could be made of micro structure with heat treatment similar to that observed with Inconel "X" and Nimonic "80." EXPERIMENTAL PROCEDURE Specimens were obtained from a hot-rolled bar of Inconel "700" of the following composition: C Mn Fe S Si 0.10 0707 0.42 0.007 0.12 Cu Cr -A1 -Ti- Co Mo Ni 0.02 -14.90 TM 2.22 27.61 2.92-- Bal. Specimens were prepared in the following heat-treated conditions: (A) 2275°F for 2 hr WQ (B) 2275°F for 2 hr WQ + 2000°F for 1 hr (C) 2275°F for 2 hr WQ + 1600°F for 48 hr. (D) 2275°F for 2 hr WQ + 2000°F for 1 hr + 1600°F for 48 hr. Empirical stress-rupture studies had shown that treatment (D) resulted in optimum stress-rupture life and ductility. Treatment (C), although giving a good aging response, resulted in low ductility. Treatments (A) and (B), respresenting individual. steps in treatments (C) and (D) were added here for microstructural comparison studies. The procedure was to make an optical and electron microscopic investigation supplemented by X-ray diffraction analysis of electrolytically extracted residues. Electron diffraction studies were made utilizing selected area diffraction techniques with extraction

Jan 1, 1960

By Frederick Jr. Prime

THE first catalogue of Geological Reports of the United States was prepared by Prof. O. C. Marsh, and published in the American Journal of Science and Arts for 1867, vol. xliii, second series. Since then the list has more than doubled, and it was thought that the publication of a new catalogue, brought down to date, would be useful to many of the members of the Institute of Mining Engineers. The compiler will be most thankful to have any omissions or inaccuracies in the list sent to him, to be published as a supplement in the next volume of the Transactions. Especially to have the correct title, number of pages, plates, and maps of any volume on the list to which an * is prefixed, as he has been unable to personally consult such works. A preliminary list was issued last February, which has been almost doubled by the kindness of many friends. The writer desires more especially to express the obligations he is under to the following gentlemen The Chief of Engineers, U. S. A.; Principal Dawson, Mr. G. M. Dawson, Drs. B. J. Harrington and T. Sterry Hunt, of Montreal; Mr. H. Engelmann, of La Salle, Ill.; Dr. F. V. Hayden and Prof. J. W. Powell, U. S. Department of the Interior ; Prof. E. W. Hilgard, University of California; Prof. Henry Y. Hind, Windsor, N. S.; Prof. C. H. Hitchcock, of Dartmouth College; Mr. Henry A. Holmes, State Librarian, Albany; Maj. Jed. Hotchkiss, Staunton, Va. ; Prof. W. C. Kerr, Raleigh, N. C.; Dr. J. S. Newberry, of Columbia College ; Prof. W. H. Pettee, of the University of Michigan ; Dr. Samuel H. Scudder, Prof. N. S. Shaler, and Prof. J. D. Whitney, of Harvard College ; Mr. Sanderson Smith and Prof. J. J. Stevenson, of New York ; Mr. Addison Van Name, of Yale College, and Lieut. Geo. M. Wheeler, U. S. Engineers. PHILADELPHIA, 907 Walnut Street, October 1st, 1879.

Jan 1, 1879

By H. C. Brown

SINCE 1934 the steel industry has been utilizing the spectrograph for supplementing wet chemical analysis in the production control of electric and open hearth furnaces. This means of control made great strides during the war years because of the general acceptance of the spectrograph and the increased emphasis that was placed on rapid control methods. However, in the post war era, with the demand still on increased production, it became apparent that a still more rapid and economical means of production control was needed. Since the spectrograph had been used mostly in the analysis of low alloying and residual elements, it also became apparent that equipment was needed to extend the spectrographic technique to the analysis of the high alloying elements in stainless steel. For these reasons, companies manufacturing spectrographic equipment were prompted to start development work on direct reading instruments. In June 1949, the Applied Research Laboratories of Glendale, Calif., announced that a direct method of spectrochemical analysis for stainless type steels had been developed. This paper will describe the use of the Applied Research Laboratories Production Control Quantometer in the quantitative control of stainless, silicon, and plain carbon steels being made at the Butler Pennsylvania Div. of the Armco Steel Corp. The Armco Butler Div. has one 70-ton electric furnace and six 150-ton open hearth furnaces. The electric furnace is employed in the making of all types of stainless steel and the open hearth furnaces are used for the production of silicon, wheel, and plain carbon steels. The ARL quantometer was purchased primarily for the purpose of controlling the steelmaking in the electric furnace, but its use has been extended for the analysis of final tests (ladle tests) on a number of different types of stainless, silicon, and plain carbon steels. Because of this additional work by the quantometer, substantial savings in manpower and time have been realized by the laboratory. In the analysis of a set of preliminary tests from the stainless steel furnace, approximately 40 min in laboratory time are saved due to quantometric analyses. Despite the fact that more specialty grades of stainless steel are being made in the electric furnace, the average tons per hour have been increased since the quantometer was put into operation. Specialty grades require more furnace time than regular commodity grades of stainless steel. The installation of the ARL production control quantometer was completed on March 13, 1952. By May 1, 1952, the instrument was calibrated for nickel, chromium, manganese, silicon, and molybdenum, which are the elements necessary for the production control of the stainless steel furnace. Within the following month, training of personnel on the quantometer was achieved and a study of the accuracy of the instrument showed that the results obtained were sufficiently accurate for control purposes. Therefore, on June 11, 1952, the quantometer was placed on production control for all types of stainless steels. Starting September 11, 1952, the instrument was gradually placed on ladle analysis (final tests) as the analytical curves were refined and additional curves were drawn. The quantometer has been relatively free of breakdowns since placing it on production control. The samples from only one stainless steel heat have had to be analyzed by wet chemistry because of instrument trouble. The previously existing heat-time record was also bettered by 15 min on a commodity grade of 18-8 stainless steel. Scope of Control In general, the quantometer determines all elements necessary for the production control of all types of stainless steel heats and for the ladle analysis of various types of stainless steel heats. It is also used in reporting final results for silicon, manganese, chromium, nickel, molybdenum, tin, copper, and aluminum on all silicon steel grades and manganese, chromium, nickel, molybdenum, tin, and copper on several plain carbon steel grades. Table I shows the elements and the concentration ranges of these elements in the various types of stainless, silicon, and plain carbon steel that are determined on the quantometer. A study of the results obtained on ladle test samples of stainless steel types 410, 430, 430 Ti, 446, 301, 302, 304, 304L, 305, and 17-7 PH will be discussed. Also included in the study are the results obtained on ladle test samples of a number of silicon steels. Apparatus In order to take full advantage of the potentials of the production control quantometer, the unit has been placed in an air-conditioned room with relative humidity control. The temperature is maintained at 73'22°F and the humidity at 45&5 pct. The air conditioning serves as a precaution to minimize the amount of adjustment and calibration needed during operation. It also reduces contaminating fumes and dust and thereby lessens the necessity for maintenance on the equipment. The quantometer is composed of three units: the high precision multisource unit, the 1.5 meter vertical spectrometer, and the console. The source unit supplies excitation conditions varying from spark-like discharges to arc-like discharges. The voltage to the source unit is supplied by a motor-generator

Jan 1, 1955

By Bernard E. Fernow

About eight years ago a comprehensive study of American timbers was begun in the U. S. Division of Forestry with a twofold object. On the one hand, it was desired to deternliiie the working-qualities of our numerous economically important timbers, and to furnish reliable standards of strength. 011 the other hand, it was intended to get a clearer insight into the properties and behavior of wood in general, with a view of establishing more rational methods in its use, and to furnish data for physical inspectioil which would permit an intelligent application of the standards of strength, and place upon a rational foundation the so-called " factor of safety," which is at present a mere baseless guess. The first object, namely, the establishment of standards for any given species, requires a very large series of tests, since Wood is an exceedingly variable substance, so much so that in the same tree a variation of 50 per cent. in strength may be found; hence the greater need of rational data of inspection. So far, the insufficient appropriations and facilities at our disposal have permitted us to establish really reliable standards for five species of southern conifers only. These have been deduced from nearly 20,000 tests. Besides these, 10,000 other tests have furnished indicatious regarding some two dozen other species. This work is now entirely abandoned, waiting for more prosperous times. The study of wood in general, however, can be carried on with smaller means, and has this year yielded not only very interesting, but highly important results, which will soon be published in detail. It is the purpose of this paper to make to the Institute the

Jan 1, 1899

By H. K. Livingston

A technique has been developed which makes it possible to determine the spreading pressure of liquids and solids, for simple systems. Data for surface tensions, interfacial tensions, spreading pressures, and contact angles for water, heptane, and silica are tabulated.' These results can be applied to the evaluation of capillary rise and displacement pressure in a petroleum reservoir. Appropriate equations are presented and the application of these equations is discussed. The presence of surface-active components affects both capillary rise and displacement pressure and also seems to influence the rate of fluid flow. The purpose of this paper is to supplement and bring up to date the last article on the subject of the surface chemistry of petroleum reservoirs, that of Garrison in the 1935 Oil and Gas Journa1.1 A discussion of the "adhesion tension" concept used by Garrison has been presented in another publication,2 together with the reasons for the recommendation that the term "adhesion tension" be abandoned. In view of the fact that some of the data used by Garrison have been superseded by more recent work, it seemed advisable to call attention to this fact and present the more important data currently believed to be correct. In the earlier paper, Garrison set up the equations that 'relate solid-oil and solid-water interfacial tensions to each other, and applied data from Bartell and Miller3 to these equations. However the adhesion tension measurements made by Bartell and Miller involved a confusion of symbols, so that they did not actually measure the spreading pressure, ?s — ?sf.2 The spreading pressure is a convenient method of indicating the amount by which the surface energy of a solid surface is lowered on immersion in a liquid or vapor. Since the initial value of the free surface energy is represented by the symbol ?s and the final value is ?sF, the spreading pressure is ?s — ?SF. A technique has now been developed4 that makes possible the determination of ?s — ?sF for simple systems. This method would be very difficult to carry out with a multicomponent system such as exists in the petroleum reservoir. However, already results have been obtained for ?s — ?sF for water and heptane in contact with silica and graphite. These values will be of the same order of magnitude as those in the petroleum reservoir. Accordingly, it is possible for the first time to discuss the surface-energy relations of the petroleum reservoir on a semi-quantitative basis. Preliminary Generalizations A petroleum reservoir may contain the following four phases: gas, hydrocarbon liquid, aqueous liquid, and solid. The three fluid phases are dispersed through the solid reservoir rock. If gravity were the only force acting, it is obvious that the

Jan 1, 1943

By H. K. Livingston

A technique has been developed which makes it possible to determine the spreading pressure of liquids and solids, for simple systems. Data for surface tensions, interfacial tensions, spreading pressures, and contact angles for water, heptane, and silica are tabulated.' These results can be applied to the evaluation of capillary rise and displacement pressure in a petroleum reservoir. Appropriate equations are presented and the application of these equations is discussed. The presence of surface-active components affects both capillary rise and displacement pressure and also seems to influence the rate of fluid flow. The purpose of this paper is to supplement and bring up to date the last article on the subject of the surface chemistry of petroleum reservoirs, that of Garrison in the 1935 Oil and Gas Journa1.1 A discussion of the "adhesion tension" concept used by Garrison has been presented in another publication,2 together with the reasons for the recommendation that the term "adhesion tension" be abandoned. In view of the fact that some of the data used by Garrison have been superseded by more recent work, it seemed advisable to call attention to this fact and present the more important data currently believed to be correct. In the earlier paper, Garrison set up the equations that 'relate solid-oil and solid-water interfacial tensions to each other, and applied data from Bartell and Miller3 to these equations. However the adhesion tension measurements made by Bartell and Miller involved a confusion of symbols, so that they did not actually measure the spreading pressure, ?s — ?sf.2 The spreading pressure is a convenient method of indicating the amount by which the surface energy of a solid surface is lowered on immersion in a liquid or vapor. Since the initial value of the free surface energy is represented by the symbol ?s and the final value is ?sF, the spreading pressure is ?s — ?SF. A technique has now been developed4 that makes possible the determination of ?s — ?sF for simple systems. This method would be very difficult to carry out with a multicomponent system such as exists in the petroleum reservoir. However, already results have been obtained for ?s — ?sF for water and heptane in contact with silica and graphite. These values will be of the same order of magnitude as those in the petroleum reservoir. Accordingly, it is possible for the first time to discuss the surface-energy relations of the petroleum reservoir on a semi-quantitative basis. Preliminary Generalizations A petroleum reservoir may contain the following four phases: gas, hydrocarbon liquid, aqueous liquid, and solid. The three fluid phases are dispersed through the solid reservoir rock. If gravity were the only force acting, it is obvious that the

Jan 1, 1943

By W. T. Bishop

For many years pine oil has been used extensively as a frother for the flotation of minerals, particularly sulphides, yet the published information available to the average user on its composition, chemical and physical properties, has been rather meager. It is the purpose of this paper to discuss these points and their relationship to the frothing properties of pine oil used in flotation processes. Pine oil, as the name implies, is a liquid obtained from the processing of wood of the longleaf and other southern pines. It is a complex mixture of naturally occurring terpene derivatives, primarily alcohols, and a smaller amount of terpenes, which has found many uses in various industries. Its use as a frother in flotation processes was the first large-scale application in industry and today the mining industry still consumes large quantities of pine oil but the textile and disinfectant industries consume comparable volumes. Much is used in soap manufacture and laundry operations. The surface-active properties of pine oil are in a large degree responsible for this versatility. History The name "Naval Stores" goes back to the days when pine tar and pitch were used to caulk leaky ships and 'Oat their ropes and rigging. Today this term is still used to include not only the oleoresinous products of the pine tree—rosin and turpentine— but other products such as pine oil, pine tar, and the many terpene and resinous compounds obtained by extracting the pine wood or tapping the tree. That part of the industry known as "wood naval stores" dates from about the beginning of this century and today produces a large part of the country's rosin and turpentine by processing pine wood. In addition, all of our natural pine oil is supplied by the wood naval stores industry, as tapping of the live tree gives only rosin and turpentine. This latter phase is known as the "gum naval stores " industry. The first successful commercial operation of the steam and solvent process of the wood naval stores in industry was carried out by Yaryan at Cadillac, Mich., in 1909.1 This operation did not prove profitable, so Yaryan went south to utilize the longleaf pine, and built a plant at Gulfport, Miss.2 Soon after, another plant was built at Brunswick, Ga., which is still in operation, and in 1914 was reported to have processed about 500 tons of wood per day.' In 1921 Hercules Powder Co. acquired the Yaryan interests, at which time the production of pine oil was only 3 to 5 million pounds per year and flotation was the largest customer. As time went on, technological advances were made, other companies entered the field, and the production of pine oil increased many fold. The growth of the industry was especially marked during the past 10 years, and in

Jan 1, 1947

By W. T. Bishop

For many years pine oil has been used extensively as a frother for the flotation of minerals, particularly sulphides, yet the published information available to the average user on its composition, chemical and physical properties, has been rather meager. It is the purpose of this paper to discuss these points and their relationship to the frothing properties of pine oil used in flotation processes. Pine oil, as the name implies, is a liquid obtained from the processing of wood of the longleaf and other southern pines. It is a complex mixture of naturally occurring terpene derivatives, primarily alcohols, and a smaller amount of terpenes, which has found many uses in various industries. Its use as a frother in flotation processes was the first large-scale application in industry and today the mining industry still consumes large quantities of pine oil but the textile and disinfectant industries consume comparable volumes. Much is used in soap manufacture and laundry operations. The surface-active properties of pine oil are in a large degree responsible for this versatility. History The name "Naval Stores" goes back to the days when pine tar and pitch were used to caulk leaky ships and 'Oat their ropes and rigging. Today this term is still used to include not only the oleoresinous products of the pine tree—rosin and turpentine— but other products such as pine oil, pine tar, and the many terpene and resinous compounds obtained by extracting the pine wood or tapping the tree. That part of the industry known as "wood naval stores" dates from about the beginning of this century and today produces a large part of the country's rosin and turpentine by processing pine wood. In addition, all of our natural pine oil is supplied by the wood naval stores industry, as tapping of the live tree gives only rosin and turpentine. This latter phase is known as the "gum naval stores " industry. The first successful commercial operation of the steam and solvent process of the wood naval stores in industry was carried out by Yaryan at Cadillac, Mich., in 1909.1 This operation did not prove profitable, so Yaryan went south to utilize the longleaf pine, and built a plant at Gulfport, Miss.2 Soon after, another plant was built at Brunswick, Ga., which is still in operation, and in 1914 was reported to have processed about 500 tons of wood per day.' In 1921 Hercules Powder Co. acquired the Yaryan interests, at which time the production of pine oil was only 3 to 5 million pounds per year and flotation was the largest customer. As time went on, technological advances were made, other companies entered the field, and the production of pine oil increased many fold. The growth of the industry was especially marked during the past 10 years, and in

Jan 1, 1947

By Stewart, J. B.

THE property at which this work was done consists of a large deposit of potash salts occurring in massive beds of rock salt, overlain by 600 ft. of salt-impregnated shales and marls. It is in the Province of Cataluiia, Spain, about 45 miles from the railway station of Mauresa and about a mile south of Suria. In addition to sinking the shaft, the program of construction work laid out by the European owners (not Spaniards) included a single-track narrow-gage railroad from Mauresa to the mine; one large office building and several large shop buildings, all of brick and concrete with steel truss roofs; two extensive benches for the future recovery plant; and a large village of stone dwellings for employees. The pay-roll showed approximately 1200 to 1500 men employed. After two years' operation, ending early in the autumn of 1920, the shaft had been sunk 325 ft. and still had an equal distance to go to reach the potash; all tunnels for the railroad were done and the road-bed $0 per cent completed; only a little more than the foundations were completed for all the large buildings, and the excavations of the benches were about 75 per cent done-while only a fair start had been made upon the employees' village. This was the state of affairs when the European owners decided to offer this property under a one-year option to an American syndicate, providing that they agreed to carry on the entire building program and to sink the shaft as fast as was consistent with the quality of work which they demanded, for they wished the shaft to endure at least 200 years.

Jan 1, 1926

By W. F. Rogers, J. A. Stewart, P. J. Kalish, E. O. Bennett

Detailed descriptions are given of materials, apparatus and the experimental procedure used to study the effect of bacteria on sandstone permeability. The factors affecting permeability during injection of bacterial suspensions which have been investigated are: (I) concentration of bacteria; (2) core permeability and median pore size; (3) species of bacteria, mode of aggregation and relative size; (4) injection rate or pressure differential; (5) mean pressure; and (6) depth of penetration of bacteria. The investigation demonstrated that bacteria cannot reduce core pertneability to zero and that their effect on permeability is subject to definite limitations. Remedial or permeability restoration studies also were made. Acidization in combination with reverse flow war found to be an effective method for restoring permeability In cores partially plugged with bacteria. The relationship between the bacterial quantities in the laboratory tests and those found in field operations is discussed. The linear laboratory flow data have been translated into terms of field radial systems; these data indicate the most practical methods of maintaining injection rates in the presence of bacteria are to increase injection pressures or hydraulically fracture the formation. INTRODUCTION It has long been known that various bacteria flourish in the above-ground components of oil field water-injection systems. The presence of these bacteria has led to the suspicion that they might enter into the causes for reduction of injection well permeability, but only recently has an attempt been made to describe the effects quantitatively.1 Biocides are used in many cases without a firm knowledge as to whether the bacteria are killed, or if they are, whether the dead cells affect formation permeability. This project was undertaken as part of a study to determine the effect of bacteria, residual oil and precipitated solids such as iron sulfide or calcium carbonate on the permeability of sandstones and to learn whether any of these materials adversely affect brine injectivity in secondary recovery or disposal operations. This report deals with that portion relating to the effect of bacteria. MATERIALS CORES Three different permeability ranges of Berea sandstone cores were used in the study. The range of initial, absolute brine permeabilities kj were: high — 278 to 400 md: medium—130 to 162 md; and low—17.7 to 48.3 md. The permeability data for the cores used in the tests are included in Table 1. All cores were cut to a nominal 1 in. diameter. Following air permeability determinations, they were molded with an epoxy resin in 1.5 in. ID aluminum sleeves. The sleeves had drilled and tapped holes for intermediate pressure connections along the length of the cores. After molding, the high- and medium-permeability cores were trimmed to 4 in. in length and the low-permeability cores to 2 in. These lengths resulted in pore volumes of approximately 10.9, 10.4 and 4.4 ml, respectively, for the high-, medium- and low-permeability cores. Pressure-transmitting channels were drilled through the plastic into the core proper, using the sleeve holes as drill guides. Width and depth of channel penetration into the core proper were approximately 0.03 in. and 0.05 in., respectively. Three pressure taps were used with all cores; for the high- and medium-permeability cores the taps were spaced 1 in. apart; for the low-permeability cores the taps were spaced 0.4, 0.8 and 1.2 in. from the inlet end. Pore size distributions were calculated from restored-state capillary pressure curves for representative cores in each of the three permeability ranges. In each case the pore size range with the greatest percentage of the pore space included the very small pores up to 0.5 micron in radius. The median pore radii were in the 5.5 to 6 micron range for the high-permeability cores; in the 4.5 to 5 micron range for the medium-permeability cores; and in the 3.5 to 4 micron range for the low-permeability cores.

Jan 1, 1965

By Clyde E. Williams

IN planning a postwar program for manufactured products, it is essential that the bases for the plans be wisely chosen. First we must make certain assumptions as to the war's ending. Let us assume: (1) complete victory by the United Nations, (2) peace terms that will ensure the direction of the economy of all nations of the world toward peaceful pursuits, and (3) an early ending of the war, that is, before the nations of the world, excluding the enemy, are near the point of physical and spiritual exhaustion. Thus, our manufacturing plants and transportation facilities will still be in good shape. The plants and transportation facilities, as well as the cities of a large part of Europe, however, will be badly crippled. The rich mineral and other raw material resources of the world, little of which was under control. of the Axis powers before the war or will be after the war, will not be used up. Control of these raw materials, or at least an important part of them, will remain in the hands of the strong peaceful nations.

Jan 1, 1943

By James E. Adler, Timothy C. Richmond

The Stillwater District is located in south central Montana approximately 75 miles southwest of Billings, the state's largest city. It lies along the northeast front of the Beartooth Mountains and is within the boundaries of the Custer and Galatin National Forests. The first white visitors in the district were the early trappers, who were soon followed by the prospectors. These early prospectors were drawn to the area by gold and silver discoveries at Cooke City in 1870 as well as by the large gossan formation in Verdigris Creek near the west bank of the Stillwater River and by several scattered smaller gossan exposures throughout the area. The first patented mining claims were recorded in September, 1886.

Jan 3, 1974

By Y. Nakada, U. F. Kocks, B. Chalrners

THE orientation dependence of work hardening has previously been studied over the entire range, i.e., including special orientations of high symmetry, in aluminum1-3 and silver.* The differences between various orientations are substantial, and the trend is the same in all fcc crystals. However, there are quantitative differences in behavior between aluminum and silver at room temperature, particularly in the (100) orientation. While many experiments on gold have been reported,5'9 none included the special orientations. We therefore undertook tension tests on gold crystals of the axial orientations (100),(110), (Ill), (211), and, as a representative of single slip, one whose Schmid factor was 0.5 (hereafter referred to as m = 0.5). Single crystals of dimensions 1/4 by .1/4 by 6 in. were grown from the melt1' at a rate of 4 in. per hr, using gold of 99.99 pct purity obtained from Handy and Harman. A growth rate of 1/8 in. per hr, or a purity of 99.999 pct,ll produced no difference in results. The crystals were annealed at 1000°C in air for 24 hr and furnace-cooled down to room temperature, after which they were electro-polished in a solution of potassium cyanide (40 g), potassium ferrocyanide (10 g), soda (20 g), and enough distilled water to make 1 liter of solution, at a current density of 0.02 amp per sq mm. After 2 or 3 hr, a very smooth surface was obtained by this method. Nine m = 0.5, two (loo), one (110), three (Ill), and one (211; crystals were tested at room temperature in a floor-model Instron machine at a tensile strain rate of 0.5 pct per min. The accuracy of the stress measurement was k10 g per sq mm up to 500 g per sq mm, k2 pct for higher stresses. The strain measurement was accurate to t2 pct. The scatter of stress at a given strain among the crystals of the same orientation was small, *5 pct being the largest. The representative stress-strain curves for various orientations are shown in Fig. 1. Table I summarizes the work-hardening parameters as used by seeger.12 Results of other investigators are also included in this table for comparison. There are no previous data for the corner orientations. Values for m = 0.5 crystals agree fairly well with those of Berner. Tm is defined as the stress at which the stress-strain curve begins to deviate from linearity of Stage 11. However, in practice this is a very difficult value to estimate because each investigator has a different idea of linearity. Therefore, the comparison with the values of other investigators may not be valid. In the present experiment, (100) crystals had the highest 111, followed by (111) crystals. The work-hardening rate in Stage I1 was highest for the (111) crystal followed by the (100) crystals. Our value for 0x1 of m = 0.5 orientation agrees very well with those of other investigators. 1) Single-Slip orientation (m = 0.5). These crystals were oriented so that the primary-slip vector was contained in one side face. The dimension perpendicular to this side should then not change if single slip indeed takes place. Within the accuracy of measurement, this dimension did not change during the deformation. Since the accuracy is k0.2 pct, the amount of secondary slip is less than 0.7 pct of the slip on the primary-slip system at 30 pct tensile strain. This is in conformity with the results obtained by Kocks" for aluminum crystals. The tensile axis moved toward (211) during the deformation. Slip bands, Fig. 2(a), were very fine and closely spaced. Some deformation bands were observed. There were no clear-cut cross-slip traces such as the ones observed on aluminum m = 0.5 crystals. 2) (111) Crystals. The orientation of the tensile axis was stable during the deformation. From this observation, one can deduce that at least three slip systems must have operated, and probably all six because the remaining three all have cross-slip relation to one of the first three.' It was very difficult to observe the slip markings. Consequently, we could not confirm by this method that six systems were operative during the deformation. At high strains (above 50 pct shear strain), this orientation had the highest stress-strain curve. At 80

Jan 1, 1964

By F. W. Smith

Within the Northern Pennine Orefield, England, intersections of fluorite veins are generally richest in ore, and their recognition enables investigation of the ore potential of the intersecting bodies. A method, based on routine analysis of fluorite for yttrium, has been used with success in mines of the district to predict the location of intersections in partially developed fluorite-bearing ore bodies. This short note is intended as a brief introduction; the details of United Kingdom applications are to be published at a later date. Geology The Northern Pennine Orefield is the second largest fluorspar-producing region in Britain. The associated minerals galena, sphalerite, chalcopyrite, barite, and witherite have all been extensively worked in the past but, with the exception of a single barytes mine, all of these operations are now abandoned. Galena alone is recovered as a byproduct of fluorspar beneficiation. At the present time two companies are producing about 38,000 tpy of fluorspar from high grade vein ore bodies, and a number of concerns are actively prospecting in old lead workings. The mineralization is localized in veins and replacement flats within favorable lithologies in an alternating limestone, sandstone, shale sequence. Since the thickness of individual beds is not great (generally less than 20 m), vein bodies tend to be ribbon-shaped, with length greatly exceeding width and height (Dunham). They thus present difficult exploration targets for conventional diamond drilling techniques. Ore grade varies greatly along the veins, which can change rapidly in character from mineral stained fault gouge to massive mineral bodies up to 10 m in width. It has been known for a very long time that the richer ore bodies tend to be associated with vein intersections in favorable beds. It is assumed that vein fissure intersections provided vertical channelways through which hot ore-bearing brines were able to ascend from deeper cavities in the sequence. Thus investigation of intersections at other horizons generally yields further ore bodies. Technique The relative concentration of yttrium in fluorite is a good indicator, in the North Pennines, of the direction of flow of mineralizing fluids. In all of the ore bodies so far studied in detail in this region, the concentration of yttrium increases markedly in the direction of vein intersections that are believed to have acted as feeder zones to the remainder of the bodies. The reason for this relationship is probably connected with the degradation of soluble rare earths-fluoride complexes by the changes in various physicochemical parameters of the hydrothermal fluids as they entered the ore body cavities from the feeder zones. The simultaneous release of free fluoride ions also contributed to the increased ore values in these intersection zones. Yttrium values in fluorite taken from a longitudinal traverse of the western ore body, Redburn mine, Rookhope, are plotted in [Fig. 1.] The position of a major vein branch and three cross veins are clearly indicated by yttrium maxima. The cross veins themselves contain up to 2.5 m of low grade fluorspar ore. The exact positions of B and C were unknown previous to the geochemical survey. Similar results have been obtained for several other veins and ore bodies in the area. Clean fluorspar was collected as bulk samples from within 300 mm of the vein wall and, since the vein infilling is simple, with mineral growth from the walls inward, analyses of the samples are considered comparable along the length of the ore body. A number of samples taken from the center of the vein show a

Jan 1, 1975

By W. V. Green

The creep-rupture behavior of commercial powder-metallurgy tungsten rod is reported for temperatures of 2250°, 2500°, 2700°, and 2800°C, stresses up to 7000 psi, and times up to 4 hr. The temperature dependence and the stress dependence of creep rates are evaluated. Rupture time is fitted to the Larson-Miller parameter and compared to lower-temperature and higher stress results reported by pugh.4 THE tensile strength of single-crystal wire1 and of polycrystalline wire2 have been measured by Goucher. More recently Bechtold3 and pugh4 have studied the mechanical properties of tungsten rod between room temperature and 1200°C. Since tungsten has the highest melting point of all metals, it should retain useful strength to very high temperatures, and should find many applications in missiles, rockets, and so forth. Therefore, the mechanical usefulness of polycrystalline tungsten rod was investigated in the 2250" to 2800°C temperature range by short-time creep-rupture tests. MATERIALS TESTED Creep specimens were machined from 1/2-in. round commercial tungsten rod which was manufactured from powder by cold pressing, sintering, and hot swaging. Purity reported by the vendor was 99.95 pct W. Spectrochemical analyses showed "traces" (less than 0.01 pct) of silicon, iron, and titanium, and "faint traces" (less than 0.001 pct) of calcium and manganese. Carbon content was 30 ppm and nitrogen content was 70 to 110 ppm. No oxygen analysis was obtained. Room-temperature stress-strain tests on the as-received tungsten gave badly scattered results. Threaded end specimens broke at the threads. When these specimens were retested using shoulder grips, the specimens broke at the shoulders. No fractures occurred in the gage lengths. The fracture stresses were: 127,000; 137,000; and 154,000 psi for three specimens which fractured at the shoulders. The microstructure of the as-received tungsten rod is shown in Fig. 1. SPECIMENS USED Fig. 2 shows the two types of creep specimens tested. The threaded-end type specimen, which was used in most tests, had a 3/4-in. gage length and 1/4-in. gage diam. The cone-end specimen, which was used primarily to investigate the effects of a smaller gage diameter and the practicability of the modified grips and specimen, had a 3/4-in. gage length and a 1/8-in. gage diam. In both cases, the gage length terminated at 0.005-in. high shoulders which served as fiducial marks for optical strain measurements. Surface finish on the gage length was 16 µ-in. rms. Creep rates and rupture times were not significantly different for the two types of specimens and were not affected by electropolishing the specimens before testing. TESTING PROCEDURE The constant-load creep-testing machine used has been described by Smith, Olson, and Brown.5 In it the specimen is held vertically by grips of similar material and on the axis of a cylindrical tungsten or tantalum heater-tube. The specimen is loaded by means of the specimen grips, a pull rod (which is sealed to the chamber lid by a vacuum-tight bellows), a mechanical lever system, and hanging dead weights. Both specimen and grips are heated by radiation from the heater-tube, which is heated by its own electrical resistance. An optical system views the incandescent specimen through slits in the radiation shielding and heater-tube. The optical system projects an enlarged image of the specimen gage length on a ground-glass screen. Periodic gage-length measurements are made on this image with two cathetometers. Thorium oxide coatings on the specimen threads or conical end surfaces completely prevented diffusion-welding of specimens to grips, and were used

Jan 1, 1960

By John Treweek

FOR many years the Homestake Mining Co. has devoted serious attention to the elimination of accidents, and ground is steadily being gained in this direction. In accident prevention work it is line-plunging with perfect teamwork and not the spectacular forward pass that brings progress toward the goal. In both surface plants and under- ground workings we regard "good housekeeping" as a first requisite for safety as well as efficiency. Under this term are included all types of safety guards and protective devices as well as cleanliness and orderliness it working places. Perhaps the most important factor in safety work is to arouse and maintain employee interest. The general morale and contentment of employees is of particular importance.

Jan 1, 1938

By D. E. Light, J. Y. Somnay

The use of alkyl acid phosphates and their alkali salts as collectors for the uranium minerals brannerite and uranothorite was investigated. In particular a detailed flotation study was carried out using isooctyl acid phosphate as a promoter. Tests were conducted on an Elliot Lake ore analyzing 0.11% U 3 O 8, chiefly as brannerite, and approximately 9% pyrite. Pyrite was floated with conventional reagents; the flotation of brannerite from the sulfide tails was studied to determine the optimum pH and pulp density to employ with isooctyl phosphate. 4 uranium recovery of over 90% was possible with a selectivity index of 8.95 when these tails were floated at 17% solids and a pH of 1.7. The effect of various modifying agents was also investigated. Aluminum sulfate, lactic acid and sodium silicate improved the selectivity of collection yielding selectivity indices of 9.5 to 11.5. Ferric chloride was found to be a depressant for brannerite. A Bancroft ore which analyzed 0.13% U308, and contained uranothorite was also amenable to flotation using isooctyl acid phosphate. The composite uranium concentrate obtained assayed 0.41% U308 at a recovery of 95.3% and a ratio of concentration of 3.24. Previous investigations1,2 on the flotation of brannerite, pitchblende, uraninite and/or uranothorite from various Canadian ores showed that fatty acids, including oleic acid and tall oils, petroleum sulfo-nates and alkyl acid phosphates, were suitable collectors for these uranium minerals. Additional work carried out by the Mines Branch in Ottawa on brannerite ores from the Elliot Lake area3 used the tall oil Acintol FA-1, or FA-2, as a collector. A recovery of 92% of the uranium in a concentrate which contained about 55% of the weight and assayed 0.2% U3O8 was obtained from a feed of 0.1% U308 in this latter instance. Eigeles et a1.4 carried out flotation on pitchblende ores and found that the most promising results were obtained with alkyl acid phosphates and their alkali salts as collectors. Within the homologous series of alkyl phosphates, the best flotation characteristics were displayed by isooctyl phosphates. Further, isooctyl phosphate derivatives were much less sensitive to hardness forming salts than oleic acid, enabling all flotation tests to be made with tap water. This paper describes tests employing alkyl acid phosphates for the flotation of ores containing brannerite and uranothorite. The flotation work described herein was conducted in conjunction with the development of a leaching process for Elliot Lake, Ontario, brannerite ores. In this process pyrite in the ore was concentrated by flotation and roasted, providing sulfur dioxide which was used to produce sulfuric acid in situ in a liquid-solid extraction process. A 40% conversion to sulfuric acid was indicated at a leaching temperature of 80°C; this resulted in the extraction of 93% of the total uranium after a contact period of 6 hr. A rotary kiln was used as a leaching vessel. Preconcentration by flotation was studied in conjunction with the above process to reduce the bulk of solids for leaching and, consequently, capital expenditure. The materials and methods used in this study will be described initially. Then the results will be presented in two sections, the first dealing with the brannerite ore, and the second with the uranothorite. Finally an economic analysis of the results on the brannerite material will be made. MATERIALS AND METHODS The two ore samples examined were from uranium-producing mines. One was a brannerite ore, a uraniferous quartz pebble conglomerate from the Elliot Lake area, which contained 0.11% U3O8, 4.3% S and 4.5% total Fe. Mineralogical studies of similar samples indicated the presence of quartz, microcline, sericite, pyrite and minor quantities of rutile, pyrrho-tite and zircon. The other ore was from a biotite-rich pegmatite in the Bancroft area; feldspar, quartz and biotite formed the major gangue components. Uranothorite was the principal uranium mineral; the head assay was 0.13% U 3 O 8. Preparation of Feed: The ores were crushed to —10

Jan 1, 1963