Search Documents

By K. Tangri, M. Chaturvedi

The addition of 0.5 wt pct Cu to Zr-2.5 Cb alloy increases the as -quenched hardness of the hexagonal martensitic a' phase, produced by water-quenching bccß-Zr phase, by about 35 pct. This strengthening has been attributed to the solid -solution hardening of the matrix. On aging ternary martensite, a' phase reverts to equilibrium a and Zr2Cu and ß-Cb precipitate out, mainly at the twin and grain boundaries, causing a secondary hardening of the matrix. COLD-worked Zircaloy-2 pressure tubes have been in use in power reactors for a considerable period of time. The search for a better material led to the development of Zr-2.5 wt pct Cb alloy which in the quench-aged condition develops 50 pct more strength than that of cold-worked Zircaloy-2, however, its corrosion resistance in water and steam in the temperature range of 316" to 400°C, in absence of neutron flux, is inferior to that of zircaloy-2.' Work carried out by Ells et al.1 and Dalgaard2 has shown that the corrosion properties of Zr-2.5 wt pct Cb alloy can be considerably improved by the ternary addition of 0.5 wt pct Cu. This paper is concerned with the effect of 0.5 wt pct Cu on the formation of martensitic a and its aging characteristics in a Zr-2.5 wt pct Cb alloy. MATERIALS AND EXPERIMENTAL TECHNIQUES Zr-2.5 Cb-0.5 Cu (referred to as the ternary alloy) and Zr-2.5 Cb (referred to as the binary alloy) alloys, supplied by the Chalk River Nuclear Laboratories of the AECL were used. The detailed chemical analysis is given in Table I. Cold rolling and swagging with frequent intermediate anneal of 1000°C were used for the initial fabrication of the alloys. All the heat treatments were carried out after the specimens were wrapped in zirconium foils and encapsulated in silica tubes under a vacuum of 5 x 10-6 mm of Hg. For optical metallography and hardness measurements specimens were mechanically and then chemically polished in a 45 pct HNOj, 45 pct HzO, and 10 pct HF solution. Hardness was measured on a Vickers hardness tester using a 10-kg load. For each specimen at least fifteen indentations were made in order to obtain a representative value. The phase identification and structural analysis were carried out using X-rays and electron diffraction techniques. Wires of 1.5 mm diam reduced to 0.12 mm diam by chemical etching were used for making Debye-Scherrer powder patterns using Cu Ka radiation in a 114.6 mm diam camera. Carbon extraction replicas were prepared by etching the specimens, after depositing a layer of carbon on the metallographic specimen, in one part HF and thirty parts ethyl alcohol. Thin films were prepared by electropolishing heat-treated 3/4 by 1/2 by 0.005 in. thick strips using a modified Bollman-Window technique. The 10 pct perchloric acid-90 pct methyl alcohol bath was kept at -50°C and polishing was done at 5 to 10 V. The thinned specimens were washed in ethyl alcohol at -30º to -40°C and dried between filter papers. Replicas and thin films were examined in a Phillips 300 G electron microscope. For resistivity measurements thin strip specimens 0.02 by 0.3 by 10.0 cm long were used. The potential leads were spot welded to the specimens in order to maintain a fixed length for the initial and the final resistivity measurements. The resistivity was measured by a Kelvin bridge in a temperature controlled room. The temperature was maintained at 72º ±1°F and the accuracy of the resistivity measurements was 0.03 µa-cm. RESULTS As-Quenched Structures. In order to produce a homogeneous matrix to study the precipitation reaction the solution-treatments of both the alloys were carried out in the -field region. From the Zr-Cb phase diagram due to Lundin and cox3 ß/a + ß phase boundary for Zr-2.5 wt pct Cb alloy is 820°C. Ells et al.1 have reported this boundary for Zr-2.5 Cb alloy containing 1100 ppm 0 to be at 920°C. Also, the addition of 0.5 wt pct Cu reduces this temperature by 50°C. Therefore, the solution-treatments were carried out at 1000°C to ensure that the alloys were in ß-phase region. The soaking time was 1 hr and the specimens were water-quenched. The as-quenched hardness of the binary alloy was 245 Vpn whereas, that of the ternary alloy was 330 Vpn. The X-ray diffraction studies indicated that the as-quenched structure of both the alloys consists of martensitic hexagonal phase a', with a c/a ratio of 1.591, and some retained ß-Zr. The presence of a' phase was further confirmed by thin film electron microscopy. Electron micrographs of typical ß-quenched structures of the ternary and the binary alloys are shown in Figs. 1 and 2, respectively. Fig. 3 shows the diffraction pattern from an area similar to that shown in Fig. 1. Although, the as-quenched hardness of the ternary alloy is about 35 pct greater than that of the binary alloy, the structure of both the alloys seems to be the same. The matrix of both alloys is heavily twinned and shows very few dislocations. Furthermore, there is no evidence of any precipitation taking place in either of the two specimens during quenching from the solution-treatment temperature. Aging Behavior of Martensitic a'. The aging kinetics of the ternary alloy were followed by resistivity and hardness measurements. The as-quenched values

Jan 1, 1970

By Albert J. Phillips

LEAD is an inexpensive metal produced and consumed in large quantities with certain chemical and physical properties that permit handling the molten metal in bulk. These properties are its low melting point, resistance to oxidation, and its negligible solvent action on iron and steel. Thus, lead is almost always melted in large iron or steel kettles, heated from beneath, and is seldom melted in either directly or indirectly fired furnaces or electric induction or arc furnaces. Even with a modest operation a kettle holding 2 or 3 tons is employed, and the size will range up to 215 tons in the large lead refineries. The methods of handling tin and its alloys are essentially the same as for lead because of the similarity in melting point and resistance to oxidation, although because of the cost of the metal the scale is more modest. In melting lead and its alloys preliminary to a casting operation it is seldom that the melting unit is completely drained of its contents. The usual procedure is to continuously charge solid metal and continuously remove small amounts of liquid metal, so that the kettle is maintained essentially full at all times. For type metals, linotype machines usually employ automatic means of adding the solid alloy to the melting pot in proportion to the removal of the liquid metal in casting slugs of type. In the casting of grids for storage batteries, frequently automatic means of charging solid metal in direct proportion to the consumption of liquid metal in the casting is used. In the manufacture of bearing alloys, new alloy is charged in direct proportion to the consumption of metal in the bearings being cast, so that at no time does the level of the metal in the melting pot lower to any great extent. Even in the manufacture of bulky commodities such as pipe, cable. sheathing, and slabs for rolled sheet, it is the practice to employ a melting kettle of several times the capacity of the casting being made. A substantial level of liquid metal in the melting kettle is thus maintained even after the casting is poured and the original metal level is quickly restored by promptly charging new metal, even though there is no immediate need to proceed with additional casting. This procedure is permissible because the amount of fuel consumed in keeping the lead molten and immediately available for use is negligibly small and the cost is more than offset by the convenience. However, this convenient procedure necessitates study and control of certain properties of lead and tin alloys that are not of serious consequence in most other alloys and for that reason are not well known. These properties are "drossing rates" and "melting segregation." DROSSING RATE Users of lead long ago observed that the rate of dross formation on the surface of the lead in their kettles or pots varied greatly from time to time. This was particularly common in places where both antimonial lead alloys and commercially pure lead were being handled.

Jan 1, 1946

By C. A. Hartinagel

During 1941, the total production of crude oil in New York state was 5,185,000 bbl. This represents a small increase over the average for the past five years. From 1921, when the annual production of the state amounted to only 988,000 bbl., there was a regular annual increase in production (excepting one or two years) until the 5,000,000-bbl. mark was reached in 1937, After more than 20 years of oil recovery by flooding methods, it was generally believed, until a few months ago, that the rate of production was nearly at its peak and within a few years the fields would experience a gradual decline as the thicker sands became exhausted and the thinner ones could be worked only at increasing costs. As a result of the present emergency, however, unusual efforts are being made, in spite of higher costs of operation, to increase the output of Pennsylvania grade oil, to which the New York product belongs. Since most of any increased production would be obtained by flooding, and since floods travel slowly, no large increase in production can be expected for some months to come. During the first year, 10 or 15 per cent increase could be obtained, but maximum production, an increase of perhaps 40 per cent, could not be expected until some time during the second or third year. In the Allegany fields, which account for two thirds of the state's oil production, 1246 wells, including water-intake wells, were drilled during the year; 390 more than in the preceding year and 590 more than in 1939. It is evident that much of the best oil territory has already been developed. As producers move toward edge properties and thinner sands, returns will be smaller, whereas costs remain the same or, under war conditions, become higher. It is estimated that at least 60 million barrels of oil is in sight and will be produced from the thicker sands by present recovery methods. In the thinner sands and edge properties, some 35 million additional barrels can be produced at a profit only if prices become higher. In view of the fact that there is little hope of finding new oil pools in New York, one of the future problems of the oil producer will be to obtain adequate returns for increased production costs. The year started with a posted price of $2.15 per barrel of crude. There were five successive price increases until the high of the year was reached at $2.98 on Aug. 14. Eight days later the Office of Price Administration directed that the price be reduced to the June level of $2.75 a barrel, which remained in effect to the end of the year. With rising costs of operation, it is feared that many of the smaller properties cannot continue production unless the Federal price cut is revoked. During the year, Allegany Refiners Inc., a local enterprise founded in 1933, with plant at Bolivar, western Allegany County, increased its refining capacity from 1000 to 1500 bbl. daily. At the same time equipment was added to make the plant a complete lubricating-oil refinery, including facilities for the refining of wax into the finished product. Previous to the enlargement, it was necessary to sell the wax

Jan 1, 1942

By C. A. Hartinagel

During 1941, the total production of crude oil in New York state was 5,185,000 bbl. This represents a small increase over the average for the past five years. From 1921, when the annual production of the state amounted to only 988,000 bbl., there was a regular annual increase in production (excepting one or two years) until the 5,000,000-bbl. mark was reached in 1937, After more than 20 years of oil recovery by flooding methods, it was generally believed, until a few months ago, that the rate of production was nearly at its peak and within a few years the fields would experience a gradual decline as the thicker sands became exhausted and the thinner ones could be worked only at increasing costs. As a result of the present emergency, however, unusual efforts are being made, in spite of higher costs of operation, to increase the output of Pennsylvania grade oil, to which the New York product belongs. Since most of any increased production would be obtained by flooding, and since floods travel slowly, no large increase in production can be expected for some months to come. During the first year, 10 or 15 per cent increase could be obtained, but maximum production, an increase of perhaps 40 per cent, could not be expected until some time during the second or third year. In the Allegany fields, which account for two thirds of the state's oil production, 1246 wells, including water-intake wells, were drilled during the year; 390 more than in the preceding year and 590 more than in 1939. It is evident that much of the best oil territory has already been developed. As producers move toward edge properties and thinner sands, returns will be smaller, whereas costs remain the same or, under war conditions, become higher. It is estimated that at least 60 million barrels of oil is in sight and will be produced from the thicker sands by present recovery methods. In the thinner sands and edge properties, some 35 million additional barrels can be produced at a profit only if prices become higher. In view of the fact that there is little hope of finding new oil pools in New York, one of the future problems of the oil producer will be to obtain adequate returns for increased production costs. The year started with a posted price of $2.15 per barrel of crude. There were five successive price increases until the high of the year was reached at $2.98 on Aug. 14. Eight days later the Office of Price Administration directed that the price be reduced to the June level of $2.75 a barrel, which remained in effect to the end of the year. With rising costs of operation, it is feared that many of the smaller properties cannot continue production unless the Federal price cut is revoked. During the year, Allegany Refiners Inc., a local enterprise founded in 1933, with plant at Bolivar, western Allegany County, increased its refining capacity from 1000 to 1500 bbl. daily. At the same time equipment was added to make the plant a complete lubricating-oil refinery, including facilities for the refining of wax into the finished product. Previous to the enlargement, it was necessary to sell the wax

Jan 1, 1942

By R. Philip Hammond

MONAZITE has had a Cinderella-like history. Although nearly go per cent pure rare-earth compound (rare-earth phosphate) it was sought at first not for the rare earths but for the sake of a minor constituent-thorium. The thorium, essential for the Welsbach gaslight mantle, was present in only small quantities and the principal constituents, the rare earths, were largely discarded. Gradually, however, the rare earths have developed uses of their own and today have left the thorium far behind in value. OCCURRENCE Monazite was first produced commercially about 1886, in North Carolina, where it was collected in small sluices by farmers who found it in stream beds on their land. The deposits were later exploited on a larger scale, but were mostly abandoned in a few years, when monazite from Brazil came upon the market in far larger quantities. Domestic production ceased entirely in 1906. The Brazilian source is still active, together with Indian, Dutch East Indies, and Australian deposits. Several other localities in the United States have yielded monazite, but none of these has produced commercially as yet. Monazite occurs originally in pegmatites and gneisses, through which, unfortunately, it is scattered in highly dispersed form. All commercially useful deposits consist of transported monazite sands liberated by erosion and concentrated by the action of water, which has sluiced away lighter materials and concentrated the heavy (D = 5.0 to 5.2) grains of monazite, together with ilmenite, zircon, garnet, and other dense minerals. The Carolina deposits were in stream beds; most of the other deposits mentioned are on or near the seashore, where the action of the waves has served to concentrate the monazite. In most cases today, the sands are worked to obtain the ilmenite and zircon, as well as monazite. The minerals are separated by means of sluices, dry tables, and magnetic separators, and each is finally obtained nearly pure. No crushing or grinding is necessary. The concentrates are shipped in fiber bags. COMPOSITION OF MONAZITE As Table I illustrates, monazite is the anhydrous orthophosphate of the cerium [ ] group of rare-earth elements. A small amount of yttrium and terbium group phosphate is also present.* All the rare-

Jan 1, 1946

By J. R. Bridge, D. A. Vaughan

The phase diagram of the Zr-H system over the range 0 to 65 atomic pet was determined by high temperature X-ray diffraction methods. Results show a eutectoid between a zirconium and the hydride phase. The eutectoid temperature was established at 560±10°C with a eutectoid composition of 42*3 atomic pet H. The hydride phase of the lowest hydrogen content is stable only above the eutectoid temperature, but is formed and retained in a metastable state during reaction of zirconium with hydrogen at temperatures below 560°C. One hydride phase is indicated that exists over the composition range 55 to 65 atomic pet H. RECENT increase in the industrial importance of zirconium has stimulated several investigations of the reaction of zirconium with hydrogen. Review of the literature on interpretation of absorption isotherms' ' shows that attempts were made to relate the observations to the room temperature hydride phases reported by Hagg.3 However, more recently Schwartz and Mallett' reported the existence of a new hydride phase, isomorphous with the lower hydride in the Hf-H system described by Sidhu.4 This phase was found adjacent to the metal in a diffusion gradient sample. In addition to the new phase, Schwartz and Mallett reported on only two of the five hydrides found by Hagg. Gulbransen" confirmed the existence of only three hydrides of

Jan 1, 1957

By I. Fatt

Networks of resistors are used as analog computers to obtain relative permeability and resistivity index curves for networks of tubes. These curves have all of the characteristics of those obtained on porous media and, therefore demonstrate the validity of the network of tubes model. INTRODUCTION In paper I' of this series the network model was shown to give information on the structure of porous media that could not be obtained from the bundle of tubes model. The agreement between the capillary pressure characteristics of a network of tubes and those of typical porous media does not prove the validity of the network made. The bundle of tubes model, although it gives less information, also shows this agreement. In this paper the flow properties of a network of tubes are shown to be in agreement with flow properties of porous media. The flow properties of the bundle of tubes model are not in adequate agreement with those of porous media. The dynamic properties of porous media, such as fluid permeability and electrical conductivity, have been found experimentally to be more sensitive functions of structure and pore size distribution than are the static properties such as porosity and capillary pressure characteristics. The network model can, therefore, be best tested by comparing the dynamic properties of a network of tubes with the observed properties of porous media. All static and dynamic properties of a completely valid model must agree with the observed properties. The most commonly measured sensitive dynamic properties are the relative fluid permeability and the relative electrical resistivity. Experimental measurements of these dynamic properties on sandstone, sintered glass, sintered alumina, and soil are reported in the petroleum and soil science literature. These properties were chosen, therefore, for the test of the network model. In the network model, relative permeability is the permeability of the network when some of the tubes are not conducting fluid, relative to the permeability when all tubes are conducting fluid. Similarly, the relative resistivity is the electrical resistivity of the network of tubes when some of the tubes are filled with a nonconductor. relative to the resistivity when all tubes are filled with the electrical conducting fluid. Single Size Tube Network The simplest porous medium is one in which all pores are of the same size. Such media can be approached by packing beds or columns of uniform size particles of sand, glass, or metal. The model of such medium in this study is a network of single size tubes. The network form, the ß factor, is usually not known for real porous media. If the validity of the network model can be established, then the study of the flow properties

Jan 1, 1957

By A. T. Beckwith

This paper concerns measurements of low-velocity air currents and investigations on mine ventilation by means of chemical smoke. The chemical smoke used is produced without flame and at ordinary mine temperatures, and therefore presents no ignition hazard in gaseous mines. Mining men who have worked in open-light mines are familiar with the use of tobacco smoke in determining the direction of air travel and approximately measuring low-velocity air currents. The use of chemical smoke is merely a refinement on the use of tobacco smoke and the flameless low-temperature source of chemical smoke has the additional advantage that it can be used in gaseous mines. Ventilation smoke apparatus, Fig I, is a simple device for producing dense white smoke. The apparatus as shown consists of a rubber aspirator bulb which is used to force air through a glass "smoke tube" containing a chemical substance that produces a dense white smoke on contact with air. The apparatus was developed by engineers of the U. S. Bureau of Mines.' It is inexpensive, weighs less than 3 oz, is easily carried in a pocket, and requires no skill to operate. Smoke apparatus is invaluable in practical mine ventilation work for: (I) measuring low-velocity air currents, (2) detecting air leakage, (3) observing airflow characteristics. This paper is written to show the merits of the apparatus, and is based upon findings through its extensive use, during the past six years, in mines operated by the Lehigh Navigation Coal Co. Inc. The Apparatus Certain chemicals, such as stannic chloride (SnCl4) and pyrosulphuric acid (H2S2O7) produce "white smoke" when exposed to air. Stannic chloride gives off vapors which on contact with moist air cause the formation of solid hydrates, of which SnCl4.5H20 is the most important. Pyrosulphuric acid decomposes when exposed to air with the evolution of sulphur trioxide (SO3) fumes, which become white upon contacting moisture in the air. A chemical, such as one of the above, is the active substance in a smoke tube. The glass tubes are hermetically sealed during manufacture, and are made ready for use by merely breaking off the tips at the conveniently located file cuts. When the smoke tube is connected to the aspirator, depressing the aspirator bulb forces air into contact with the chemical, and smoke discharges from the open end of the tube. A white solid (a hydrate if stannic chloride is used, or sulphur trioxide if pyrosulphuric acid is used) may occasionally form a cake in the outlet opening of a smoke tube. A small wire such as an ordinary paper clip can be conveniently employed to dislodge the cake should it seal the tube. When the assembled apparatus is not

Jan 1, 1949

By Charles W. Allen

The Athens mine is in the city of Negaunee, Mich. It is one of the larger producers of soft hematite ore on the Marquette iron range. The property is held under lease by the Athens Iron Mining Co., and is operated by the Cleveland-Cliffs Iron Co., which is a partner with Pickands, Mather & Co. in the Athens company. The mine was opened in 1913, and shipments of ore commenced in 1918, the total reaching 3,063,711 tons up to Jan. 1, 1932. Diamond-drilling from surface, together with a knowledge of geological conditions in neighboring properties, gave a comprehensive picture of the location, size and shape of the orebody before shaft-sinking started. Striking east and west, the orebody entered the east boundary of the property at a depth of about 1500 ft. below surface. A pitch of 15" to the west carried it down to about 2500 ft. on the west boundary, about double the depth of that of any soft-ore property heretofore worked on the Marquette Range. The width of ore averaged close to 500 ft., and the thickness 300 feet. The depth of the deposit and its size, together with an overburden of quicksand, which in places reached a thickness of 150 ft., presented unusual mining problems. The use of a caving system made surface drainage into the orebody inevitable, because the north boundary of the deposit was a vertical diorite dike 200 ft. wide, and the south boundary a northward-dipping impervious slate. S. R. Elliott, manager of the mining department of the Cleveland-Cliffs Iron Co., who was superintendent of the mine at that time, conceived the idea of starting at the bottom of the orebody and working upward, reversing the usual mining procedure. This innovation divided the Athens orebody into a series of steps, or blocks, the first of which was adjacent to the western boundary, and therefore in the lowest portion of the deposit. Top-slicing was to start under the capping in this first block by raising from the bottom level, and development and mining were to progress upward in successive blocks to the east. A complete description of the Athens system of mining was

Jan 1, 1934

By R. D. Caudle, Yoginder P. Chugh, V. K. Agarwala

Longwall coal mining is a growing mining technique in the United States. However, very little premining exploration data are collected presently by coal companies to 1) select coal winning equipment, 2) select and design face supports and supports in gate and tail entries, or 3) optimize operational parameters such as length, width, and orientation of face. The authors are of the opinion that much of the data needed for mine planning and design for longwall mining can be obtained during exploration. In this paper, the authors identify the data requirements, discuss how these data can be obtained during exploration, propose an exploration program and estimate the cost to obtain the necessary data.

Jan 1, 1982

By William P. Blake

THE use of diamonds upon a large scale in drilling rocks, and the substitution to a certain degree of rotary diamond drills for the ordinary steel percussion drills, marks a new era in the art of mining. Since the invention by Leschot of the diamond drill, it has steadily advanced in its utility and range of application, and in the appreciation of miners and engineers. I t must be claimed as one of the many gifts of science to the arts ; and it is, in particular, one of the fruits of the scientific education given at the Ecole Centrale, at Paris. Members are all, doubtless, more or less familiar with the construction of the drill and of the machinery by which it is applied in boring. I t is, therefore, my present purpose only to direct your attention to some recent marked improvements, made by the American Diamond Drill Company, by which the economy and efficiency of the machines have been increased. Form of Bit.-The annular or ring form of the drill-head or bit was, I believe, the earliest; and it is still in use, without essential modification, wherever it is desired to obtain a sample " core" or specimen of the rock traversed. But for mere drilling, regardless ~f the preservation of a test-core, a solid-head bit is preferred, except for very large holes. Until recently, these solid-head bits were made with a pointed cutting face shaped like an obtuse cone. This form was assumed to be the best, being most in accordance with the experience obtained with percussion drills. I t is found, however, that the exact reverse

By William P. Blake

THE use of diamonds upon a large scale in drilling rocks, and the substitution to a certain degree of rotary diamond drills for the ordinary steel percussion drills, marks a new era in the art of mining. Since the invention by Leschot of the diamond drill, it has steadily advanced in its utility and range of application, and in the appreciation of miners and engineers. It must be claimed as one of the many gifts of science to the arts ; and it is, in particular, one of the fruits of the scientific education given at the Ecole Centrale, at Paris. Members are all, doubtless, more or less familiar with the construction of the drill and of the machinery by which it is applied in boring. It is, therefore, my present purpose only to direct your attention to some recent marked improvements, made by the American Diamond Drill Company, by which the economy and efficiency of the machines have been increased. Form of Bit. The annular or ring form of the drill-head or bit was, I believe, the earliest; and it is still in use, without essential modification, wherever it is desired to obtain a sample "core" or specimen of the rock traversed. But for mere drilling, regardless of the preservation of a test-core, a solid-head bit is preferred, except for very large holes. Until recently, these solid-head bits were made with a pointed cutting face shaped like an obtuse cone. This form was assumed to be the best, being most in accordance with the experience obtained with percussion drills. It is found, however, that the exact reverse

Jan 1, 1873

Some Things We Don't Know about the Creep of Metals. By H. W. Gillett (T.P. 1087) Reduction of Iron Ores under Pressure by Hydrogen. By Michael Tenenbaum and T. L. Joseph (T.P. loll, with discussion) Induction Furnaces for Rotating Liquid Crucibles. By E. P. Barrett, W. F. Hol- bRook and C. E. Wood (T.P. 986, with discussion) Mechanism of Solidification and Segregation in a Low-carbon Rimming-steel Ingot,. By Anson Hayes and John Chipman (T.P. 988, with discussion) Solidification of Rimming-steel Ingots. By A. HultGRen and G. PhRagmen. (Contribution 112) Dendritic Structure of Some Alloy Steels. By Daniel .I. Martin and James L. Martin (T.P. 1066, with discussion) Occlusion and Evolution of Hydrogen by Pure Iron. By George A. Moore and Donald P. Smith (T.P. 1065, with discussion) Structure of Iron after Con~pression. Hy Charles S. Barrett (T.P. 977, with discussion) Structure of Iron after Drawing, Swaging, and Elongating in Tension. Ry Charles S. Barrett and L. H. LevensoN (T.P. 1038, with discussion) Magnetic Torque Studies of the Texture of Cold-rolled and of Recrystallized Iron-silicon Alloys. By Leo P. TaraSovJ(T.P. 1012, with discussion) Influence of Atmosphere and Pressure on Structure of Iron-carbon-silicon Alloys. By Alfred Boyles (T.P. 1046) Kinetics of the Decomposition of Austenite at Constant Temperature. By J. H. Austin and R. L. Rickett (T.P. 964, with discussion) Reaction Kinctics in Processes of Nucleation and Growth. By William A. Johnson and Robert F. Mehl (T.P. 1089, with discussion) Phase Changes in 3.5 Per Cent Nickel Steel in the Acl Region. By I. N. Bavarine (T.P. 1031, with discussion) Chromium in Structural Steel. By Walter Crafts (T.P. 1055) Surface Allotropic Transformation in Stainless Steel Induced by Polishing. By J. T. BuHwell and J. WUlff (T.P. 1032, with discussion) Nature of :Passivity in Stainless Steels and Other Alloys, I and 11. Ry H. H. Uhlig and John WUlff (T.P. 1050, with discussion) Thermal Expansion of Nickel-iron Alloys (Nickel from 30 to 70 Per Cent). Ry J. M. Lohr and Charles H. Hopkins (T.P. 987, with discussion) Low-temperature Transformation in Iron-nickel-cobalt Alloys. By L. L. Wy~Ian (T.P. 1013, with discussion) Fracture of Steels at Elevated Temperatures after Prolonged Loading. By R. H. Thielemann and E. R. Parker (T.P. 1034, with discussion)

Jan 1, 1939

Some Things We Don't Know about the Creep of Metals. By H. W. Gillett (T.P. 1087) Reduction of Iron Ores under Pressure by Hydrogen. By Michael Tenenbaum and T. L. Joseph (T.P. loll, with discussion) Induction Furnaces for Rotating Liquid Crucibles. By E. P. Barrett, W. F. Hol- bRook and C. E. Wood (T.P. 986, with discussion) Mechanism of Solidification and Segregation in a Low-carbon Rimming-steel Ingot,. By Anson Hayes and John Chipman (T.P. 988, with discussion) Solidification of Rimming-steel Ingots. By A. HultGRen and G. PhRagmen. (Contribution 112) Dendritic Structure of Some Alloy Steels. By Daniel .I. Martin and James L. Martin (T.P. 1066, with discussion) Occlusion and Evolution of Hydrogen by Pure Iron. By George A. Moore and Donald P. Smith (T.P. 1065, with discussion) Structure of Iron after Con~pression. Hy Charles S. Barrett (T.P. 977, with discussion) Structure of Iron after Drawing, Swaging, and Elongating in Tension. Ry Charles S. Barrett and L. H. LevensoN (T.P. 1038, with discussion) Magnetic Torque Studies of the Texture of Cold-rolled and of Recrystallized Iron-silicon Alloys. By Leo P. TaraSovJ(T.P. 1012, with discussion) Influence of Atmosphere and Pressure on Structure of Iron-carbon-silicon Alloys. By Alfred Boyles (T.P. 1046) Kinetics of the Decomposition of Austenite at Constant Temperature. By J. H. Austin and R. L. Rickett (T.P. 964, with discussion) Reaction Kinctics in Processes of Nucleation and Growth. By William A. Johnson and Robert F. Mehl (T.P. 1089, with discussion) Phase Changes in 3.5 Per Cent Nickel Steel in the Acl Region. By I. N. Bavarine (T.P. 1031, with discussion) Chromium in Structural Steel. By Walter Crafts (T.P. 1055) Surface Allotropic Transformation in Stainless Steel Induced by Polishing. By J. T. BuHwell and J. WUlff (T.P. 1032, with discussion) Nature of :Passivity in Stainless Steels and Other Alloys, I and 11. Ry H. H. Uhlig and John WUlff (T.P. 1050, with discussion) Thermal Expansion of Nickel-iron Alloys (Nickel from 30 to 70 Per Cent). Ry J. M. Lohr and Charles H. Hopkins (T.P. 987, with discussion) Low-temperature Transformation in Iron-nickel-cobalt Alloys. By L. L. Wy~Ian (T.P. 1013, with discussion) Fracture of Steels at Elevated Temperatures after Prolonged Loading. By R. H. Thielemann and E. R. Parker (T.P. 1034, with discussion)

Jan 1, 1939

By T. D. Murphy

This chapter deals with those types of silica raw materials that have been segregated and refined by natural processes into nearly monomineralic deposits and hence, by virtue of their high degree of purity, have become the sources of commodities having special and somewhat restricted commercial uses. In some instances, these raw materials occur in nature as unconsolidated quartzose sand or gravel and can be exploited and used with very little preparation and expense. More often, they occur as sandstone, conglomerate, quartzite, quartz mica schist, or massive igneous quartz which must be crushed, washed, screened, and sometimes chemically treated before commodities of suitable compositional and textural characteristics can be successfully prepared. The occurrence and distribution of silica raw materials is summarized and an effort has been made to bring commodity definitions, critical properties, and specifications up to date. Presentation of mining and processing methods is considered beyond the scope of this article; they are, for the most part, conventional and well known. New production techniques are currently reported in the trade journals and are later adequately described in technical publications as promptly as competitive restrictions allow. Discussion on Basis of Use ABRASIVE USES Industrial silica used for abrasive purposes falls into three main categories: (a) blasting sand; (b) glass-grinding sand; and (c) stone-sawing and rubbing sand. Blasting sand is a sound closely-sized quartz sand which, when propelled at high velocity by air, water, or controlled centrifugal force, is effective for such uses as cleaning metal castings, removing paint and rust, or renovating stone veneer. It is commonly referred to as Sand Blast sand. Multicycle quartz sand is an efficient blasting agent by merit of its survival characteristics which are soundness, toughness, and hardness. Steel grit and shot have supplanted it to a large extent but owing to their higher cost and tendency toward deterioration in storage, are still not universally used. It is conceded that angularity promotes faster cutting but this is offset by a higher loss in fines. The peening action of a rounded grain is a desirable feature in achieving a satin finish for certain light metal castings but a subangular grain is unsurpassed for fast heavy cutting. Specifications are chiefly based on size frequency distribution but it is mandatory that the grain be free of adhering clay or irony coatings. Material that dusts upon handling will not be tolerated. There is no uniform trade designation for the many blasting sand grades. Most producers sell on the basis of numbered grades; that is, No. 1, No. 2 and so on, this generally connoting fine to coarser grades. Designation of grade by the two sieve sizes between which most of the material lies, is practiced in some areas. Thus, in a No. 1220 grade, 98 pct of the material passes a 12 mesh sieve and is retained on a 20 mesh sieve. Blasting sand specifications vary according to use. Coarse grades range from 4 mesh to 12 mesh, medium grades range from 12 mesh to 30 mesh, finer grades may range from 20 mesh to 100 mesh or finer. Specifications generally call for narrow limits of gradation, requiring precise sizing methods. The fact that most blasting sands are retained

Jan 1, 1960

By Alden B. Greninger

THE time-honored description of the growth of metal crystals to form polycrystalline aggregates is. one in which two important steps are considered: (1) nucleation, and (2) dendritic growth, each dendrite starting from its individual nucleus and resulting (upon slow cooling, assuming no solid phase changes) in a macrograin. This picture of the process of crystallization is incomplete, and it is with the hope of enlarging upon it that the following summary and correlation of experimental results are given. MOSAIC STRUCTURE For an exact definition of the mosaic structure of metal crystals-if, indeed, one can be found that will hold for all metals-one must await the results of much experimental work in this field. The writer's investigations have been. confined almost entirely to copper and a few of its alloys. The following terms are proposed, and will be used in this report: Macromosaic Structure1.-Large-scale mosaic structure; more specifically, mosaic structure of a scale large enough to produce splitting of Laue spots on back-reflection Lane X-ray patterns2. The deviation from exact parallelism of neighboring macromosaics varies from a few

Jan 1, 1935

By W. Irwin Moyer

Two methods for the rapid valuation of oil properties are in common use. The one best known and most widely used is the "per barrel" value, based on the present daily production of the well, without regard to its past performance or the history of the sand or pool from which it produces. The second method is the "time to pay out," or the lengt of time required for a well to place itself upon the credit side of the ledger, from which time the returns from its production (less the operating expenses) will be clear profit. The time basis for valuation is also commonly used in the appraisal of an undeveloped lease. In most oil fields, it is not thought good business to invest in production that will not pay out in at least 4 to 5 years. Nearly all buyers (except in certain regions of very persistent production like the deep-sand territory of the Appalachian field) expect wells to pay out in considerably less time than this. Like the barrel-per-day price, the time necessary for a well to pay out has been determined for each field, so that one frequently hears a field or district referred to as having a certain time to pay out. This is considered the norm for that field or district and the buyer and seller base their value, to greater or less extent, on their belief in the accuracy of this time. The writer long ago became convinced of the inaccuracy of the barrel-per-day method, except when greatly modified for local conditions, such as the age of the wells, their economic limit, operating conditions in the field, the future price of oil, and the persistence of the sand as a producer. When so modified, this method becomes more of an analytic or predicted probable-yield valuation. While the appraiser may not go through each step in a valuation based on future returnable revenue, his knowledge of the field and the local conditions surrounding his leases make it possible for him to estimate a fair sales value that, in many cases, will be a close approximation to the truth. This is quite different from she commonly understood barrel-per-day value, in that the conditions turrounding the sale of one lease or property at a fair market value may

Jan 1, 1923

By W. Irwin Moyer

Two methods for the rapid valuation of oil properties are in common use. The one best known and most widely used is the "per barrel" value, based on the present daily production of the well, without regard to its past performance or the history of the sand or pool from which it produces. The second method is the "time to pay out," or the lengt of time required for a well to place itself upon the credit side of the ledger, from which time the returns from its production (less the operating expenses) will be clear profit. The time basis for valuation is also commonly used in the appraisal of an undeveloped lease. In most oil fields, it is not thought good business to invest in production that will not pay out in at least 4 to 5 years. Nearly all buyers (except in certain regions of very persistent production like the deep-sand territory of the Appalachian field) expect wells to pay out in considerably less time than this. Like the barrel-per-day price, the time necessary for a well to pay out has been determined for each field, so that one frequently hears a field or district referred to as having a certain time to pay out. This is considered the norm for that field or district and the buyer and seller base their value, to greater or less extent, on their belief in the accuracy of this time. The writer long ago became convinced of the inaccuracy of the barrel-per-day method, except when greatly modified for local conditions, such as the age of the wells, their economic limit, operating conditions in the field, the future price of oil, and the persistence of the sand as a producer. When so modified, this method becomes more of an analytic or predicted probable-yield valuation. While the appraiser may not go through each step in a valuation based on future returnable revenue, his knowledge of the field and the local conditions surrounding his leases make it possible for him to estimate a fair sales value that, in many cases, will be a close approximation to the truth. This is quite different from she commonly understood barrel-per-day value, in that the conditions turrounding the sale of one lease or property at a fair market value may

Jan 1, 1923

By Paul J. Fopiano

SOME relationships between the flow characteristics of iron single crystals of 99.9 pct purity and the behavior of imperfections have been investigated. X-ray rocking-curve measurements and etch-pit counts were made as a function of plastic strain, and compared to the stress-strain curve obtained on a modified Polyani tensile machine. Crystals grown from rolled strips of vacuum-melted iron by the strain-anneal method1 had a high preference for a (110) longitudinal direction and a (211) face normal. The tensile specimens were prepared from 2 by i by 0.040 in. single crystals having a gage area of 3 by \ in. Rocking-curve measurements were carried out with a highly perfect germanium monochromating crystal in which the dazz spacing was matched to that of the dZl1 in the ir0n.l Well-collimated CuKal radiation was used throughout. These procedures practically eliminated errors due to geometrical and wavelength resolution. Inasmuch as the rocking-curve half breadth may vary markedly from point to point in the specimen being irradiated, the crystals were strained in place by mounting a hydraulic loading device on the double-crystal spectrometer. The rocking curves were taken after each increment of strain in the unloaded condition, since no observable difference was found in the rocking-curves between the loaded and unloaded states. The rocking-curve half breadths of the as-grown specimens were in the range 90 to 120 sec of arc when the beam irradiated an area of about -£ by -& in. on the specimen. DeMarco and weiss3 have shown that, for a well-colli- mated X-ray beam, irradiating about 10"! sq in. of the very same material, half breadths within 10 pct of the Darwin natural half breadth were observed. Since the rocking-curve specimens were stressed by the load-unload technique, the strain achieved at any given stress depended on the time of holding because of low-temperature creep. Fig. 1 shows the rocking-curve half breadth (also area/peak height) as a function of plastic strain for a relatively short holding time (2 to 5 min) at each stress level. For strains less than 0.1 pct the rocking-curve breadth is essentially constant; it is only for larger strains that there occurs a significant increase in this breadth. Where the holding times at each stress level were longer (by well over an order of magnitude) there occurs a significant increase in the rocking-curve breadth only after plastic strains of the order of 0.6 pct had been introduced into the specimen. This observation is related to the time dependence of creep phenomena and emphasizes the difficulty in comparing data obtained by two such different straining methods. Etch-pit results were obtained using a 2 pct nital etch on specimens strained in the range of 0 to 1 pct. Prior to etching, all specimens were annealed for 3 hr at 150°C, the carbon content being sufficient to decorate the dislocations for strains of at least 1 p~t.~ The data points were all taken from parts of the same single crystal which had been strained with short holding times at stress in increments of strain of the order of tenths of 1 pct. The (211) plane is particularly difficult to etch-pit in vacuum-melted iron and therefore it is felt that these values are as much as an order of magnitude low. Fig. 2 shows the etch-pit density as a function of plastic strain. The smooth curve passing through the data points is not meant to infer a quantitative correlation with the rocking-curve data. What is of interest, however, is the change in etch-pit density in the region of 0.2 pct plastic strain. The first three increments in strain (points 2,3, and 4) did not produce a measurable change in the etch-pit density while subsequent increments did produce a measurable change. While the absolute values of these results do not appear to be cor-

Jan 1, 1967

By Forbes K. Wilson

Dick Hunt is known for having said, "Ore bodies are found but mines are made." This was certainly true of the Ertsberg-it was stumbled upon, literally, by a group of mountain climbers, but to develop it into a mine took 12 years of concerted effort. For more than a century, explorers had attempted to penetrate the jungles of New Guinea and climb the snow-covered Mt. Carstensz, named for a Dutch navigator who first saw it in 1620. But the first to succeed was the Colijn expedition which reached the 5030-m (16,500-ft) pinnacle in December 1936 after starting out from the south coast57 days earlier. Members of that expedition were A. H. Colijn and Jean Jacques Dozy, employees of Shell Oil Co., and Lt. Wissel, a pilot in the Royal Dutch Navy.

Jan 6, 1977