Search Documents

By G. Sherburne Rogers

Introduction. ONE of the features of oil-field work that puzzles operator, chemist and geologist alike, is variation in the gravity of the petroleum produced, on neighboring leases or even from adjoining wells. Few fields in the United States yield oil that is of uniform gravity throughout; in some, fields the different grades are produced from different sands, in a few from different formations, and in many from different areas in the same sand. In a few cases, perhaps, a common assumption-that the heavier oil is derived from the lighter through the escape of the more volatile constituents-is valid, but many cases can not be explained in this way. Although in the California fields the specific gravity of the oil generally decreases with depth, there are numerous exceptions to this rule; and, as in many other regions the light oil is found nearest the surface, it is evident that evaporation underground is generally an unimportant factor. It is generally recognized that the great differences between petroleum from widely separated fields are due largely to differences in age and degree of metamorphism and to variation in the composition of the original organic matter; but in the writer's opinion some of these broader differences, as well as most of the minor variations in the character of the oil from any one field, are clue to the local action of natural reagents such as sulphur or oxygen. This is particularly likely to be true if the oil has migrated from one formation to another, as in the California fields; and in some areas it appears that variation in sulphur content may even afford a rough index of the extent or distance of the migration. It is the purpose of this paper to call attention to the chemical action of sulphur and oxygen on petroleum, to show that the gravity of the oil from any one field is intimately related to its sulphur content, and to discuss the possi-

Jan 7, 1917

By Walter Rose

Theoretical expressions are presented to describe wetting and non-wetting phase relative premeability relations. These expressions have then been compared with existing published data, the conformance noted being sufficiently good to satisfy the requirements of some engineering use. As a consequence, it may be supposed that relative permeability characteristics of porous media now can be inferred from basic core analysis data, in a manner more convenient (although less direct) than presently available methods of experimental evaluation. INTRODUCTION This paper presents a new approach to the problem of relative permeability evaluation. A classification of published discussions of relative permeability concepts which have appeared in the petroleum literature will show that previously emphasis has been placed on methods of experimental measurement, on the interpretation of the data so obtained with respect to the variable properties of the system, and on theoretical and practical considerations which relate relative permeability to gross fluid behavior in petroleum reservoirs. Essentially, no detailed examination has appeared which treats the fundamental factors controlling the quantitative features of the relative permeability relation*, although cer- tain references can be Cited where a qualitative awareness of their existence and nature is indicated. This condition is explainable in terms of the recognized complexity of the problem, and in order to provide some basis for theoretical development, the general emphasis has been placed in the past on experimental procedures of evaluation, the validity of which, in principle, could be confirmed by the analysis of well and reservoir performance. However, because of the experimental difficulties which have been encountered (notably, difficulties due to the so-called "end effects"), and because of the general unreliability of field performance tests required to study the applicability of the data, relative permeability phenomena continue to be incompletely understood and described.? In this paper is examined the possibility of predicting relative permeabilities entirely from fundamental considerations. In addition, attention is called to certain important factors, previously unemphasized in the published literature, which now can serve as a basis for the eventual experimental confirmation of this and similar theoretical approaches, as well as the experimental solution of the problem in general. Therefore, the analysis presented herein has the dual purpose both of orienting future experimental activity and also of providing an immediate solution for the relative permeability porblem, sufficiently adequate for some engineering use. It will be seen that the conclusions reached are supported by theoretical and intuitive considerations, and they are not contradicted insofar as gross features are concerned by existing concepts and interpretations of published experimental data, except as specifically noted. Darcy's law, expressed simply as: k dp q = k/u dp/dx .......(1) where q is linear rate of flow (assumed horizontal), k is the † The poor comparison usually obtained between laboratory and field gas-oil ratios (c.f.. Fig. 4 of paper by L. E. Elkins) is illustrative of conditions which dimcourage unqualified acceptance of the results of previous studies except as presently useful approximations. In this connection, Evinger and Muskat have discussed in detail the discrepancy observed between field well productivity values and values obtained from the analysis of laboratory flow data.

Jan 1, 1949

By Walter Rose

Theoretical expressions are presented to describe wetting and non-wetting phase relative premeability relations. These expressions have then been compared with existing published data, the conformance noted being sufficiently good to satisfy the requirements of some engineering use. As a consequence, it may be supposed that relative permeability characteristics of porous media now can be inferred from basic core analysis data, in a manner more convenient (although less direct) than presently available methods of experimental evaluation. INTRODUCTION This paper presents a new approach to the problem of relative permeability evaluation. A classification of published discussions of relative permeability concepts which have appeared in the petroleum literature will show that previously emphasis has been placed on methods of experimental measurement, on the interpretation of the data so obtained with respect to the variable properties of the system, and on theoretical and practical considerations which relate relative permeability to gross fluid behavior in petroleum reservoirs. Essentially, no detailed examination has appeared which treats the fundamental factors controlling the quantitative features of the relative permeability relation*, although cer- tain references can be Cited where a qualitative awareness of their existence and nature is indicated. This condition is explainable in terms of the recognized complexity of the problem, and in order to provide some basis for theoretical development, the general emphasis has been placed in the past on experimental procedures of evaluation, the validity of which, in principle, could be confirmed by the analysis of well and reservoir performance. However, because of the experimental difficulties which have been encountered (notably, difficulties due to the so-called "end effects"), and because of the general unreliability of field performance tests required to study the applicability of the data, relative permeability phenomena continue to be incompletely understood and described.? In this paper is examined the possibility of predicting relative permeabilities entirely from fundamental considerations. In addition, attention is called to certain important factors, previously unemphasized in the published literature, which now can serve as a basis for the eventual experimental confirmation of this and similar theoretical approaches, as well as the experimental solution of the problem in general. Therefore, the analysis presented herein has the dual purpose both of orienting future experimental activity and also of providing an immediate solution for the relative permeability porblem, sufficiently adequate for some engineering use. It will be seen that the conclusions reached are supported by theoretical and intuitive considerations, and they are not contradicted insofar as gross features are concerned by existing concepts and interpretations of published experimental data, except as specifically noted. Darcy's law, expressed simply as: k dp q = k/u dp/dx .......(1) where q is linear rate of flow (assumed horizontal), k is the † The poor comparison usually obtained between laboratory and field gas-oil ratios (c.f.. Fig. 4 of paper by L. E. Elkins) is illustrative of conditions which dimcourage unqualified acceptance of the results of previous studies except as presently useful approximations. In this connection, Evinger and Muskat have discussed in detail the discrepancy observed between field well productivity values and values obtained from the analysis of laboratory flow data.

Jan 1, 1949

By N. B. Davis

I . INTRODUCTION WHILE working with a number of very sticky cracking clays from western Canada the writer became interested in a study of the cause of the excessive plasticity, This led to a review of the rather bulky literature on the subject and the finding that plasticity still remains to be satisfactorily explained. Most of these investigations seem to have been carried on solely from the chemical viewpoint, the geologic aspects having been ignored. In nearly every case, the investigators have worked with the higher-grade clays of low to medium plasticity, such as the kaolins, the excessively plastic ones having generally been neglected, partly because of their limited application, yet the author believes that these are

Jan 2, 1915

By R. J. Caro

The Anaconda phosphate plant was put into operation in the fall of 1923. Its present daily operating capacity is approximately 170 tons of treble superphosphate and 16 tons of phosphoric acid analyzing 42 pct P2 O5 and 52 pct P2 Os, respectively. As a result of the continued increased demand for phosphates, Anaconda decided in 1947 to expand the plant's daily output to 270 tons of treble superphosphate and 54 tons of phosphoric acid. The present daily plant intake is 335 tons of wet (footwall) phosphate rock analyzing 31.7 pct P² O5 and 0.28 pct V² O5. The rock is shipped from Anaconda's mine at Conda, Idaho, in open railroad cars, having been crushed to pass 3/8 in. mesh at the mine.' The expansion program will require an increased intake of 300 tons of rock per day. The hanging-wall rock anaIj-ses approximately 30.5 pct P2 O5 and 0.11 pct V² O5, and will be beneficiated in a new washing plant under construction

Jan 1, 1950

By O. George Specht, Carl A. Zapffe

IN recent print, some remarkably contradictory statements have appeared regarding the importance to be attached to sponge iron,1-6 a metallurgical commodity whose history goes back at least to the time of Diodorus Siculus in the fourth century B.C. This disagreement, however, expresses the lack of a satisfactory method for producing sponge iron rather than defection in the commodity. The blast furnace is admitted to have certain inherent disadvantages, such as a general unsuitability for magnetite and the heating and blowing of vast quantities of undesirable nitrogen, so that a workable sponge-iron process remains attractive. In this respect, low-temperature gaseous reduction shows especial promise; but confusion persists regarding the factors involved. The present paper, therefore, has three principal divisions: (I) an exhaustive examination of all previous work on low-temperature gaseous reduction, (2) experimentation on the reduction of a magnetite with hydrogen, and (3) development of certain thermodynamic relationships in reduction, with a summarized depiction of the factors in the general process. PREVIOUS INVESTIGATIONS Gaseous media used in the reduction processes under discussion can be classified in three types: (I) H2, (2) CO, and (3) other gases. In the second, the CO is often admixed with H2. The third principally comprises hydrogeniferous gases, such as natural gas and producer gas, and in addition includes chlorine. Because hydrogen therefore features in all three, a study of hydrogen reduction based on investigations using pure hydrogen alone may be incomplete. The present paper reviews the three groups of investigations in the listed order, paying particular attention to hydrogen reduction. For the benefit of future workers, an exhaustive bibliography has been prepared and similarly classified. GROUP I: REDUCTION WITH HYDROGEN Equilibria Although the present problem is specifically one of kinetics, a first consideration is the equilibrium of the system, since the reactions to be studied comprise that equilibrium, and their direction and end points are defined by it. The historic development of these researches is interesting and informative.

Jan 1, 1946

By P. H. Dudley

The present paper was suggested by the paper read by Mr. R. W. Hunt at the New York Meeting, in February last, on rail-sections (Trans., xvii., p. 778)) in the discussion of which I brought forward some of the facts and observations here stated. Professional duties having prevented me from writing out my part of that discussion in time for its publication in the volume containing Mr. Hunt's paper, I take the opportunity to present it in separate form and greater fulness. The striking features of the series of rail-sections submitted by Mr. Hunt are their shallow heads and heavy bases. In these respects they are quite similar to the section of the 80-1b. rail, which I designed in 1883 to meet the requirements of the traffic of the New York Central and Hudson River Railroad. Before the adoption of the 80-1b. rail, this road had modified its 65-1b. section from a shallow head with rounding sides and quite heavy base to one having a deep head and thin base. All the leading railroads had changed from the earlier sections of steel rails to those having deep heads and thin bases, conforming to the recommendations of the Committee on Rails of the American Society of Civil Engineers. It is but proper to say that the committee's investigations upon the wear of rails were made upon the rails manufactured under a practice quite different from that which obtained after the committee's recommendations were carried into effect. The results in actual service have been contrary to what was expected. Fig. 1 shows my 80-1b. section of 1883. Before designing this rail I had taken, at different times, a series of diagrams of the condition of tracks, with my car, on the New York Central and Hudson River Railroad, all of the New England railroads, and all but one of the trunk lines. My diagrams gave me an opportunity which could not otherwise have been obtained to see the wear of great numbers of sections of rails under widely varying conditions of traffic.

Jan 1, 1890

By H. M. Howe

PART I. INTRODUCTORY. § 24. INTRODUCTION.-This paper discusses the chief existing data as to the temperature, in iron-carbon alloys, of Ae.3, the upper limit of the transformation range when in equilibrium, as distinguished from Ac3, the temperature at which the end of the transformation is noted in heating up, and from Ar3, that at which its beginning is noted in cooling down. The former is in fact carried above Ae3 and the latter below Ae3 by lag. I touch incidentally on the influence of manganese on Ae3 (§ 29, p. 1102). The sections, tables, and illustrations, are numbered consecutively with those in the accompanying papers by Howe and Levy on Determination of, the Position of Ae3 in Carbon-Iron Alloys, and by Burgess, Crowe, and Rawdon on Thermal and Microscopical Examination of Professor Howe's Standard Commercial Steels, to which the present paper forms a sequel. § 25. The contradictoriness of our present evidence is shown by grouping it together in Fig. 14. For instance, both Goerens and Meyer (Series 2) and Meuthen (Series 12) used practically stationary temperature, and thus reduced the influence of lag very greatly; yet Ae3 for 0.32 carbon steel according to the former investigators is 894°, but according to Meuthen it is at or below 770°, a discrepancy of 124° or more. In view of our ability to measure these high temperatures within a few degrees, the existence of such a discrepancy is as unwelcome as it seems needless. I attack the thankless task of bringing some order out of this chaos.

Jan 6, 1913

By Glenn C. Waterman

THE diamond drill is a very important tool in exploration and development testing and its use is increasing. In almost all cases results of diamond drilling are analyzed on the basis of grade and tons. A proper evaluation of core and sludge assays is important if drilling results are to be acceptable as a basis for geologic and engineering appraisal. The relatively wide variation in assay averages as calculated by various well-known combining methods indicates that the engineering choice of a method may affect the outcome of the drilling in terms of ore and waste. The problem of combining assay results from core and sludge samples has been discussed many times in conference and in the literature.'-' Most writers agree that the field of disagreement in methods is large and that the engineer on the job must consider features unique to his drilling, pick one of several combining methods, and depart from the rules when abnormal results come in. All the discussion to date can be summed up by the admission that as yet there is no fairly simple, generally acceptable combining method that is practicable over a wide range of drilling conditions, ground conditions, and ore occurrence. The combining problem is important in evaluating drilling results at Chuquicamata. Recently a reappraisal has been made of recovery variables and their effect on assays, with the result that a new combining method is offered which fits average drilling conditions and is mathematically reasonable. It is simple in application, fundamentally correct, and an improvement over most combining methods. At Chuquicamata diamond drillholes are used to outline the grade and position of blocks of normal and marginal grade oxide, mixed, and sulphide ore. Most holes penetrate all classes of material (and waste), and it is important for mining programs as well as ore reserves to know almost precisely the soluble and insoluble copper content of mineralized ground. At present three classes of ore are mined and treated differently. For an orderly sequence of mining operations which can provide regular daily tonnages of all three ore types and keep grade at certain levels with minimum variation, ore type and its grade must be predicted. Diamond drilling plus geologic mapping and bench sampling are tools for prediction. And drilling data are largely used to calculate grade of material more than a few meters away from bench faces. The orebody at Chuquicamata" is criss-crossed by millions of barren or mineralized weak to fairly strong slips and fault fissures. Mineralization is diverse and encompasses many quartz and oxide or sulphide-bearing copper veins, as well as seams and disseminated grains. Copper occurs in oxide or sulphide minerals or mixtures of these two mineral types. Rock conditions vary from intensely seri-citized (soft and porous) through clay-altered ground to almost fresh granodiorite. The result is an orebody which offers many obstacles to good and consistent core recovery in diamond drilling. Recovery varies considerably in the several alteration zones, the various types of oxide and sulphide ores, and the position and inclination of the drillhole within the complex fracture pattern. As core recovery drops sludge samples must be used with core samples to calculate grade. Many years of drilling at Chuquicamata indicate that in good grade oxide zones and in the sulphide areas core recovery is good and the ground uniformly mineralized. Moderate loss of core, therefore, does not markedly affect grade calculations based on core assays. An early core-sludge combining method used core assays at face value as indicating grade down to 50 pct core recovery, but below this recovery percentage sludge samples were used and weighted according to the standard Longyear chart. This method apparently did not introduce serious errors, but it abruptly used sludge assays with high weighting factors representing 100 pct return irrespective of actual percentage of sludge recovered. Recent drilling activities have been directed toward outlining the marginal ore areas. The non-uniform mineralization and generally poorer core recovery in such ground indicated that a more exact core-sludge combining method was required to equate wide differences between core and sludge assays and recovery. In fringe ore areas at Chuquicamata core recovery averages about 50 pct, from a minimum of 10 to 15 pct to a maximum of 100 pct. Sludge recovery is likewise variable and averages perhaps 80 pct even though holes are cemented as water return falls off. In a homogeneously mineralized area cut by many slips and faults, with hard and soft ribs, loss of core is loss of ground which has a grade similar to that of core recovered, and core assays approximate true grade. In this case sludge samples need not be used. However, it would be unusual to know beforehand that an area is uniformly mineralized, and in fact this condition is probably uncommon. Generally the distribution of valuable minerals in the ground does not exactly compare with their recoverability in core. Thus, in the usual case, loss of core decreases the

Jan 1, 1956

By Frank Reiber

The study of earthquakes long ago developed the fact that by study-ing the travel .times of the various groups of waves from the same earthquake, as received on seismographs :it varying distances, major discont'inuities in the earth's crust, could be reasonably well defined. Using this original discovery, and adapting the mathematical methods originally devised in seismology for determining the depth below the surface at which such discontinuities occur, other investigators were able to develop a new branch of seismology which promises to be extremely useful in extending the boundaries of our information on local conditions Below the earth's surface. As an outstanding example of the applications of this work, we have the so-called " seismograph " exploration of the Gulf Coastal region, which has resulted in the discovery of a large number of salt domes, from many of which oil fields may be developed. The original seismological investigations, from which different major discontinuities in the earth's crust were deduced, as well as these later successful experiments in locating salt-dome structures, involve relatively simple problems. In each case we arc dealing with surface materials in which elastic waves will be propagated with a fairly definite velocity. Under this material we have something quite different', in which the elastic waves will be propagated with a much higher velocity. The transition from one medium to the other is likewise relativtly abrupt. For example, in the Gulf Coastal region the sedimentary formations have a velocity of 6000 or 7000 ft. per sec., while the velocity of elastic waves in the cap rock of a salt dome may exceed 15,000 ft. per sec. Under such conditions, delineation of the formation is a relatively simple matter, and, furthermore, there is very little opportunity for ambiguous results. Development of Elastic-wave Method The success of this Gulf Coast work immediately suggested the advisability of attempting to extend elastic-wave methods to a point

Jan 1, 1929

By John D. Wiebmer

Lignite Development in North Dakota is a "shotgun wedding" according to former state senator Robert L. Stroup-the unwilling groom (North Dakota) is being led to the altar by the nation's demand for increased coal production. The state's attorney general, Allen I. Olson, reacts to the situation this way: "We have no specific coal policy. We plan to keep the whole matter down to a dull roar and drag our feet until we see how we fit into the national energy picture." But despite a state administration labeled as "cautiously negative" toward resource development, North Dakota has experienced a twofold increase in annual lignite production within the last two years. And within the next four years, three more mine additions will double the state's output again.

Jan 8, 1977

By Virgil Kirkham

NORTH AMERICA has for many years led the world in phosphate production, but with development of African deposits and their marketing conditions with respect to European countries, this leadership will shortly pass to Africa. Algeria, Egypt, Tunis, and Morocco have large phosphate reserves and a correspondingly large production because of easy mining and a ready European market, which was developed during the war. An increase in home consumption is destined to develop for the eastern American fields, and the countries of the Pacific will provide a market for the western producers. New processes indicate a decrease in fertilizer costs, which will encourage a more widespread domestic use and assure better marketing conditions. The African deposits, although benefited by a water haul, have the disadvantage of being isolated from a source of acid so that the crude rock is shipped from Africa to its destination, whereas in the United States the chief product shipped is acidulated rock or various types of superphosphatic fertilizers. The principal types of phosphate deposits used in the manufacture of fertilizers are guanos, apatite, phosphatic marl, phosphatic limestone, phosphatic shale, and phosphate rock which is also known as phosphorite. Some of these deposits are found on each of the continents; Table 1 gives their occurrence, age, location, character, extent, etc. Most of , the information found in this table represents a compilation of information published elsewhere in a different form and widely scattered.

Jan 1, 1925

By Eli Sani

Investment in the mineral industries-particularly in the mining industry-differs from investment in nonminera1 industries in that the latter have an indeterminate life, assumed to be perpetual, and are not called upon to replace the firm's original investment. In mining ventures, on the other hand, once the ore bodies are depleted the mine has no economic value; the original capital investment must be returned to the investor by the time the ore is exhausted. A mining venture is also characterized by the significant cost and time associated with the exploration phase. A myriad of samples must be taken, geological features investigated, and ore grade assured. In addition, most mining ventures require substantial capital expenditures aggregating several hundred million dollars for a number of years before the project begins producing any revenue. Any theoretical model employed in evaluating a mining venture, as well as similar mineral ventures, must take all these factors into consideration.

Jan 5, 1977

By J. J. Scott

INTRODUCTION Rock mechanics theory needs to be applied to solve ground control problems, but in the final analysis the mining method and equipment which is used will be those which solve problems in a practical manner. Equipment and its inherent productivity and safety as supplied as "off the shelf" items by manufacturers often dictate the size of mine openings. Operators may tolerate falls of ground and associated hazards if productivity and safety problems are not too severe. In this whole process the costs of mining finally dictates just what system will be employed and what equipment will be used. True solutions to ground control problems sometimes require that the mine operator step back and totally rethink his problems. The true cost of accidents are often missed and hidden in overhead costs. Losses in production and accompanying profit are not fully considered, false economics, such as using inappropriate roof support devices, are undertaken at times when using the most expensive devices to totally eliminate accidents may be the best overall solution. Automation to remove the worker from the hazard area is often over- looked as the initial capitol expense to apply it may be high. Cooperation between mine engineers, mine operators, safety personnel, equipment suppliers, and government inspectors, both state and federal, is required to reach workable solutions that best meet the goals of all parties.

Jan 1, 1983

By S. Skowronski

OvErpolEd copper, as commonly defined,- is copper which has been excessively reduced during the poling period of the refining process. Owing to its porosity, such coppcr is unfit for commercial purposes. The cause of this phenomenon is undoubtedly the lack of oxides in the copper, yet this does not completely explain it. Refined copper of the same "pitch" and "set" varies considerably in oxygen contents, and analyses of overpoled bars also show similar wide differences; moreover, it is possible to melt copper in 'crucibles so as to obtain bars that are practically free from oxygen although they show a "tough pitch" and "level set" surface. Frederick Johnson advances the following theory: The regulation of the quantity of oxygen in copper is the keynote of all copper refining. It is the presence of a well defined proportion of oxygen in the form of cuprous oxide, forming a copper-cuprous oxide eutectic, which enablcs copper to be cast free from blowholes. It seems that when oxygen is present, other gases are less soluble in molten copper; when oxygen is absent, or is present in insufficient quantity, the copper dissolves other gases, such as hydrogen and carbon monoxide, which are insoluble in the copper when solid, and, being rejected during the process of solidification, causes internal porosity and external ridges and excrescences.1 The "level set" of wire bars, etc., is entirely the result of a compromise between the occluded gases and cuprous oxide. With excess of the former the metal would be "overpitch" and spongy, while an excess of the latter would result in the metal being "underpitch" and brittle.2 The result of the absorption and subsequent expulsion of reducing gases, carbon monoxide and hydrogen,' and the effect of this action on the overpoling of copper are in dispute; the literature on the subject is full of contradictory statements and will continue to be so until better analytical methods have been developed. Sulfur, however, is tangible. The refiner can see it in his button sample and consequently attributes to it any trouble that may happen during the melting of the copper.

Jan 1, 1919

By Frederick W. Bacorn

The paper of Reno H. Sales on Ore Deposits at Butte, Mont.,' is a careful and painstaking work, an important contribution to the literature of the subject. As is almost inevitable in a work of such magnitude, a few misstatements occur; and some of these I shall endeavor to point out. Mr. Sales has also fallen into error, as I think, in the application of his theory of ore deposition; and while the modification which I venture to suggest is a minor one geologically, it is of great economic importance. I refer to Mr. Sales's idea of an outward migration of mineralizing solutions from a supposed central copper zone. In order that I may make myself plain, I must first epitomize the theory as a whole, which I understand to be this: All of the Butte ore deposits (save those along the Continental fault, not herein considered) are derived from solutions of magmatic origin, which, at the beginning of their ascent from a great depth, were acid in reaction, hot, and were carriers of copper, zinc, manganese and other metals. As they departed from their point of origin they lost heat, and, because of reactions with the wall rock, became more and more alkaline. The metal deposited from these solutions in their hot condition was principally copper; and, as they cooled, they deposited less and less copper and more and more manganese and zinc, until the copper practically disappeared. With this theory in general I have no fault to find, nor have I, it must be stated, the qualifications necessary to enable me to pass upon it critically; but it seems to me to be reasonable and probable, and is one which I am quite willing to accept. But Mr. Sales, for what seem to me to be insufficient reasons, has assumed that there is one deep central source of copper, relatively rich and small, from which all the solutions emanated. From this central source the solutions rose, through one channel or through a group of channels, to the surface, at and within a small area called the central copper zone,

Jan 1, 1915

By Ian Wark

IN defending the chemical theory of flotation, Taggart, del Giudice and Ziehl have criticized1 the views of those who prefer to attribute the effects of certain flotation agents to adsorption. Perhaps with some justifica-tion, they describe the latter term as the "haven of refuge of writers lost in a morass of shaky experiment and muddy thinking." We prefer to regard it, however, as a haven of refuge for writers who seek a conven-tional term to describe the formation of films of flotation reagents on solid surfaces, because in many cases it is not yet possible to specify the forces that hold them there. Originally, as Taggart and his associates state, adsorption connoted a. concentration difference and nothing more. In recent years, workers in the field of surface chemistry have tacitly added other meanings, and they now speak of orientated adsorption of unimolecular films on a solid sub-strate, of chemi-adsorption, and of exchange adsorption. Thus the term adsorption may connote-simply the Gibbs layer of excess concentration at the surface of a solution, or a unimolecular film at the surface of a solid. Perhaps this has led to the misunderstanding of Taggart, del Giudice and Ziehl concerning the relationship between surface tension and adsorption at solid surfaces. The change in "surface tension" accompanying adsorp-tion at a liquid surface can be used as a measure of the adsorption, and the Gibbs equation as quoted by these authors correlates these two con-ceptions. But, to correlate two conceptions does not necessarily imply an attempt to explain either, although sometimes. such an "explanation" is carelessly inferred. Use of "surface energy per unit area" instead of the numerically equal but more difficult and less definite conception of "surface tension per unit length" would lessen many of the present diffi-culties. (Compare with Adam.2) At interfaces involving a solid phase, neither "surface tension" nor "interfacial tension" can have any meaning, but the conception "interfacial energy per unit area" can be understood by anyone who is familiar with the concept of free energy. While it is true that surface energy cannot be directly measured at a solid surface,

Jan 1, 1936

By Robert R. Turner, Arthur R. MacPherson

This chapter reviews the steps which should be taken from the time it is decided to consider autogenous grinding in the development of a new ore deposit or the expansion of an existing plant up until the purchase of the new autogenous mills. In this case the term autogenous includes semi -autogenous, secondary pebble mills, and lump milling as well as fully autogenous grinding systems. Also, both wet and dry grinding alternatives have been included. Before the test program it must be decided how many bulk samples are required to properly assess the autogenous grinding possibilities of the deposit. Also, a decision must be made on where and how the samples are to be ground i.e. pilot mill at site or in established location, wet and or dry grinding, etc. In the test program itself, certain fundamental data must be obtained. The testing should include enough work to determine whether fully autogenous or semi-autogenous grinding should be used and what type produces best power efficiency. Also, all the other pertinent data should be collected such as power; tonnages; feed, charge, and product sizing; circulating loads, etc. If a secondary mill is required to produce a final grind the decision on whether a pebble or ball mill should be used may require additional test work. Finally, the concentration of the mineral may play an important part in selection of the circuit and should become a part of the final testing once the grinding has been established.

Jan 1, 1978

By George W. Becker, Blair R. Benner, Ronald J. Roman

A computer model for the leaching of oxide copper heaps is developed and verified in laboratory tests. The model can be used to scale-up laboratory test data and to simulate the results of various operating philosophies on heap leaching. The model is applicable to leaching processes where the rate of leaching is controlled by a deficiency of reactant or diffusion of a reactant through the leached rock. Several examples are presented showing the sensitivity of the recovery vs. time curve to the variables in leaching.

Jan 1, 1975

By E. L. Brack

ASARCO's copper smelter at Hayden, Arizona has been upgraded to meet the increasing Environmental Protection Agency (EPA) and Occupational Safety and Health Administration (OSHA) environmental standards. Fortunately, means were found to accomplish these standards and provide for more efficient operations. With the adaptation of oxygen flash smelting and other related operations at Hayden, ASARCO has turned to the use of minicomputers and microprocessors for inter-plant communications and local area process control. The applications of distributive and computer controls to the plant operations at the Hayden smelter are discussed in this paper.

Jan 1, 1984