Search Documents

By Richard P. Rothwell

THE anthracite coals of Pennsylvania are all mined from large veins. A seam less than four feet. in thickness is generally considered as unworkable, those from which most of the coal now comes being from 8 to 30 feet thick. The system of mining employed is, almost without exception, that known as "chamber and pillar work;" that is, the coal is taken out of chambers of from 18 to 30 feet in width, and pillars of from 12 to 20 feet are left between these to support the roof. In general, the entire thickness of the seam, even

Jan 1, 1875

By H. I. Aaronson

The nucleation of pearlite at proeutectoid ferrite is inhibited, to an increasing extent, at the following locations: At twin boundary-nucleated ferrite, between closely spaced ferrite sideplates, and at intragranular plates. These effects are discussed in terms of the influence of transformation strain energies and of the interfacial free energy of austen-ite:ferrite boundaries on the rate of pearlite nucleation. The growth of pearlite into the interiors of austenite grains from the region of the grain boundaries is markedly restricted when low reaction temperatures and large austenite grain sizes permit the development of interlocking networks of intragranular ferrite plates. PREVIOUS investigators have made extensive studies of the interactions which occur between the proeutectoid ferrite and the pearlite reactions from the viewpoint of the mechanisms through which pearlite interferes with the nucleation and growth of proeutectoid ferrite.1-3 In the present investigation, the processes through which proeutectoid ferrite (hereafter termed simply "ferrite") can reduce the rate of formation of pearlite have been explored in some detail. A steel with a relatively low carbon content, in which the ferrite reaction can compete successfully with the pearlite reaction over a wide range of reaction temperature, and exceptionally coarse-grained specimens, which further emphasize the role of the ferrite reaction, have been employed for most of this work. A brief examination also has been made, however, of the effects of smaller austenite grain sizes upon these processes. Experimental Procedure The steel employed had the following composition: 0.29 pet C, 0.76 pet Mn, 0.25 pet si, 0,007 pet S, and 0.005 pct P. This alloy was homogenized for 48 hr at 1250°C. The investigation was performed

Jan 1, 1959

By Arthur Phillips

DURING the past few years considerable interest has been shown in the study of fiber, and its effect, in wrought metals. Fiber has recently been defined as a "condition of parallelism of important lines or details in the structure. "1 Briefly stated, two distinct types of fiber are commonly encountered. One results from the alignment in the direction of working of constituents, more or less segregated, such as slag, oxides, carbides and dendritic formations. The second, and least understood, type is produced by working the metal below the recrystallization temperature in such a way as to develop a parallelism of the grains. This condition is readily recognized by the pronounced elongation of the grains in the direction of working. Under certain deformational treatments the grain fragments produced by cold working tend to orient in certain definite directions with respect to the axis of extension. Furthermore, even in metals that have been annealed after cold working preferred orientations may be present. It is perhaps logical to assume that such marked parallelism of structural elements would be manifested by directional properties in the metal. As a matter of fact, tests on many kinds of materials have shown differences in varying degrees. In recognition of this condition, propel design, for many purposes, places the fiber axis in such a way as to present the direction of maximum strength to the greatest applied stress.

Jan 1, 1931

By J. E. Jopling, J. R. Chenneour, E. L. Derby, S. R. Elliott

The Marquette range, on which are situated the iron mines of Mar-quette County, together with a few in Baraga County, Mich., extends from a point 10 miles southwest of Marquette westward for 30 miles. The tracts are usually a multiple of the standard 40-acre parcel, which is the smallest government subdivision of a square mile or section. About half of the mines are held in fee, these being owned by the older mining companies. Some of them date back to about 1880, and a few are as early as 1850. During the past 40 years most of the mines opened have been on leased lands, the royalty being either for a stated amount per ton or a percentage of the selling price of the ore at the lower lake ports, or the selling price on board of cars at the mine. The first merchantable body of ore discovered in the Lake Superior district was found, in 1845, at what is known as the Jackson mine, near Negaunee. This ore was hard hematite. After unprofitable attempts had been made, in 1848, to smelt it in forges, shipments were begun to lower lake ports, which increased rapidly upon the completion of the locks at Sault Ste. Marie, in 1855, and the railroad from the mines to Marquette, in 1857. Beginning with the Pioneer, in 1858, a number of small charcoal furnaces were built to smelt a part of the product. At various points in the upper and lower peninsulas, large charcoal furnaces are still making iron from the ores of the Marquette range. In connection with these furnaces are byproduct plants. As the deposits were opened up, soft ore was encountered, but for a few years this was disregaided, as only the hard ore was used. Underground mining was begun about 1880 and during the next few years the open-pit mines producing high-grade ore were exhausted. The first mines in the district were owned by the Jackson, Cleveland, Lake Superior, Lake Angeline, Champion, Iron Cliffs, Humboldt, Republic, and Michigamme companies. Many of these companies have been merged in the holdings of The Cleveland-Cliffs Iron Co., which controls most of the tonnage of the district.

Jan 1, 1925

By D. E. Thomas

Oxidation rate constants were determined for Cu-Pd and Cu-Pt alloys as a function of alloy composition and temperature. Reaction products were identified. Relationship between oxidation rate constants and diffusion constants in the reaction zones is discussed. THE mechanism of oxidation of alloys is consider--'¦ ably more complex and not so well understood as that of pure metals. The oxidation of a one-phase binary alloy of which one component is a noble metal should logically be the simplest case of alloy oxidation, for in this case one is concerned presumably only with the oxidation of the base metal and the diffusion process by which it reaches the reaction site. This had led a number of investigators to study such systems. Probably the earliest work was that of Tammann and Rienacker' on the tarnishing of Cu-Au alloys at temperatures up to 300°C. These alloys oxidize according to the logarithmic law, that is, the film thickness is proportional to the logarithm of the time. The rate of film formation was found to decrease with increasing gold content. Raub and Engel² investigated the oxidation of Au-Cu, Cu-Pd, Au-Ag-Cu, Au-Pd-Cu, and Ag-Pd-Cu alloys at 750°C in air. These alloy systems form a continuous series of solid solutions at the temperature of oxidation with the exception of those containing silver. Au-Cu alloys oxidize parabolically, the rate constant decreasing slowly with increasing gold content up to about 15 atomic pct* Au, and more rapidly thereafter. An alloy with 14 pct Cu forms only a very thin layer of CuO on the surface and probably also a subscale.† Alloys containing more than 14 pct Cu have scales consisting of CuO and subscales of Cu,O embedded in nearly pure gold. The Cu-Pd alloys obey the parabolic law except for slight deviations for alloys containing 53 and 84 pct Cu. The overall oxidation rate decreases rather smoothly with increasing palladium content. A scale consisting of a thin layer of CuO and a thick layer of Cu²O and a subscale of Cu²O embedded in nearly pure palladium was observed for alloys containing 84, 53, and 30 pct Cu. An alloy with 19 pct Cu formed only a subscale of CuO embedded in nearly pure palladium, and an 8 pct Cu alloy formed only a thin film which was presumed to be PdO. The ternary alloys considered by Raub and Engel oxidized in much the same way as did the binaries. Wagner and Grunewald³ found that Ni-Au alloys, oxidized at 900°C in oxygen, formed a scale of NiO and a subscale containing NiO and gold. The overall oxidation rate increases with increasing gold content, passes through a maximum and then decreases to zero for pure gold. The fact that gold increases the oxidation rate was attributed to "pores" in the scale. Kubaschewski' investigated the air oxidation of alloys of platinum or gold with up to 10 pct Cu or Ni at temperatures in the range 300" to 1550°C. Parabolic behavior was noted for all alloys except Au-Ni, with rates decreasing in the order Au-Cu, Au-Ni, Pt-Ni, Pt-Cu. The diffusion coefficients for the latter three systems are known, and they decrease in the same order. However, activation energies for the oxidation of these alloys do not agree with the activation energies for diffusion in the respective alloy systems. Kubaschewski and Goldbeck7 nvestigated the oxidation of Ni-Pt alloys in air at temperatures of 600"

Jan 1, 1952

By J. E. Hove

The high temperature physical properties of graphite are reviewed and interpreted in the light of present day knowledge of the mechanisms affecting these properties. The thermal and mechanical behaviors only are discussed and, whenever possible, comparisons are made with other refractory materials. Possible further studies are indicated, including some carbide work. AS long as the term high temperature implied only temperatures up to about 1000°C, the materials problems which arose could usually be handled by fairly conventional metal alloy types, such as the Co-Cr-Ni superalloys, for which there exists a great deal of technology. Perhaps this temperature can still be considered an upper limit for normal applications, but it is certainly true that the number of abnormal applications is increasing rapidly. The advent, in recent years, of ram-jet and rocket missiles and of high power nuclear reactor heat sources has raised a host of questions concerning the basic problem of what material to use in the temperature range up to 2000°C and higher. While there are, of course, many metals, in the second and third transition series, which melt at considerably higher temperatures than this, these metals are, at present, pretty well excluded from practical use by other considerations, such as re-crystallization, chemical activity, or excessive plastic deformation. The behavior of metals, from the standpoint of dislocation theory, is just beginning to be understood and thus there is some hope for the future development of very high temperature metals, but the immediate problems would most logically appear to have solutions involving the nonmetals, such as the refractory ceramics and graphite. For this reason, there is presently a great deal of engineering and experimental research being performed on the latter materials, much of this research being exploratory in the sense of gathering new property data. The situation, so far as graphite is concerned, is somewhat more fortunate than with the other refractory solids in the sense that a great deal is already known about its basic properties. This stems both from the fact that the carbon-carbon bond has been of interest to chemists for a long time (and graphite can be considered as a very large aromatic molecule, if desired) and the fact that its properties, both as a function of temperature and of radiation damage, are of critical importance to nuclear reactor designers. It is still true, of course, that such fundamental questions as why graphite remains solid to such a high temperature and why it has such a high thermal conductivity cannot entirely be answered at the present time. It is, nonetheless, meaningful and instructive to consider such problems in the light of existing knowledge. This is what the present paper will attempt to do. Before going on, it may be appropriate to classify graphite and justify its discussion before readers primarily interested in metals. Graphite is comparatively unique among materials in that there is always a property or group of properties which precludes calling it either a metal, a semiconductor, or a ceramic. It has the high electrical and thermal conductivities of a metal, but the artificial, poly-crystalline types show a negative thermal coefficient of electrical resistivity, generally characteristic of semiconductors. On the other hand, semiconductors, by definition, show an ever increasing resistivity as the temperature is lowered, whereas graphite approaches a finite, and, indeed, a rather low resistivity in the region of 10°K and, furthermore, a good single crystal of graphite has a positive temperature coefficient, as for a metal.' On still another hand, its porosity and brittleness at lower temperatures would put graphite in the ceramic class although, unlike most ceramics, it is readily machinable and has a high resistance to thermal shock. All things considered, it is probably more nearly appropriate to call graphite a metal than anything else. Although certainly outstanding in some ways, graphite has its peculiarities and, especially if the reader is unfamiliar with the data, it is probably valuable to review some representative property variations at high temperature. This review is meant to be mainly illustrative and no attempt has been made to be exhaustive. Review of High Temperature Properties At ordinary pressures, graphite does not melt, but sublimes directly into the gaseous phase at about 3700°C. Although the phase equilibrium diagram is still in some doubt, graphite will melt, at a slightly higher temperature, at pressures in excess of about 100 atm. The chief difficulty of using graphite in an oxidizing atmosphere is that the reaction rate becomes quite high at fairly low temperatures. If a threshold oxidation temperature2 is defined as the temperature at which graphite loses 1 pet of its weight in 24 hr, the value in air is 450°, the value in steam is 700°, and the value in carbon dioxide is 900°C. Efforts are presently being made to raise this threshold temperature either by impregnation with a retardant of some type (sodium tung-state and phosphoric acid, for example) or by a suitable metal or oxide coating. It is probably fair to say that, to date, these attempts have not shown any outstanding success in all respects. Most commercial graphites are fabricated by impregnating a carbon flour (say of coke or lampblack particles) with some type of hydrocarbon

Jan 1, 1959

By Clyde Orr

INTRODUCTION Cracks, crevices, holes, and fissures -- here collectively termed pores -- occur in all manner of substances in sizes from those evident to the unaided eye to those well below electron microscopic levels of detection. Naturally occurring materials having varying degrees of porosity are represented by wood, rock, soil, and mineral formations. Man-made materials that are porous include ceramics, sintered metals, catalysts, adsorbents, filters, and various compacted objects. The extent of their porosity greatly influences the hardness, rigidity, integrity, and general usefulness of such materials, and assessing both their pore volume and size is becoming increasingly necessary. Means by which this pore information can be obtained is the subject here. No attempt will be made to include all techniques and variations of them that have been suggested, but, hopefully, those of most general applicability will be described in sufficient detail to enable a potential user to judge their merit for a particular need. The results of pore measurements are made useful by relating them through other tests to performance criteria such as weatherability, water penetration, frost damage, oil recovery, strength, or thermal or electrical conductivity. These tests, of course, are outside the bounds for inclusion here. A pore is variously defined in dictionaries as "a minute opening", "a small interstice admitting passage of liquid", and "an interspace between particles". Clearly any object through which it is possible to find a continuous path from one side to the other either for a liquid or a gas must be regarded as porous. Passageways are not necessary for porosity to exist, however. There are so-called blind

Jan 1, 1980

By R. F. Shurtz

This paper relates geostatistical doctrine to classical statistical and mathematical concepts. It is not a contribution to geostatistics; it is a contribution about geostatistics. It uses descriptive and pictorial arguments to assist interested readers in forming an intuitive grasp of the recondite and difficult mathematical issues involved. The method chosen is to cite authoritative literature references from the two fields and trace connections between them. Four broad conclusions appear: first, geostatistics comprises a relabelled subset of concepts detached from classical statistics and mathematics; second, this relabelling artificially isolates geostatistics from the classical fields and restricts its scope; third, the classical fields still have much to offer to the mining industry but will remain fallow unless artifcial communication barriers are removed; and fourth, the unique advantages asserted for geostatistics are neither unique nor necessarily real. These findings should not be regarded as iconoclastic but rather as Pointing the way to a wider and more productive scope for those who evaluate mineral deposits.

Jan 1, 1983

By C. O. Fairchild

THE meaning of temperature control can be extended to cover not only the control of temperatures' but also the control of processes through a knowledge of the temperatures involved. In this sense it has a very wide interest. A list of the industries in which temperature control is used in one way or another would cover nearly the entire industrial field. This discussion will be confined to the field of high temperatures. In practically all industries involving operations at high temperatures, pyrometers are used or men are paid for their ability either to estimate temperatures or gage an operation by some physical or chemical change or condition dependent on temperatures. As progress is made in the development of instruments and of methods for measuring temperature, some of these highly skilled artisans are learning the use of a new tool. Many processes have been, in recent years, improved by means of exact measurement thus substituted for estimation, but in a great many industries the pyrometer has had practically no opportunity to demonstrate its usefulness. The perfecting of instruments must be accompanied with a dissemination of the knowledge that new instruments are available and can be economically used. The demand at present, however, is ahead of the supply, and many industries are handicapped by the want of pyrometers. One of the highest paid skilled tradesmen of the present time is the man in the steel rolling mill who knows when proper working temperatures are attained. The metallurgist in his development of steels is continually demanding closer adherence to given temperature ranges in the processes, and the pyrometer is rapidly becoming indispensable. Properties of the finished products are being correlated with working temperatures and so closely that in some cases even the pyrometer is taxed to give the required accuracy. The greatest progress has been made in those industries in which the lower temperatures are used, particularly below 500° C. In this lower range automatic control has been highly developed.

Jan 9, 1919

By E. A. Slover

THE usual reverberatory system of smelting cop--1- per concentrate or calcine has for its component parts a furnace and one or two waste heat boilers. These parts are operated on a basis of compromise, since the furnace can send gas to the boilers at too high a temperature and the boilers by plugging, due to dust or slag, can place a definite limit on the amount of fuel the furnace can burn. Over the years the copper concentrate smelting furnace has had few advances in design. The simple rules of design such as the flame should wipe the bath and the speed of the gases should be reasonably low for dust carrying purposes seem to cover the main features. In the construction of the individual furnaces some innovations are always being introduced. Among these are charging so that the work of smelting is a complete bath process, the use of suspended brick arches in place of sprung arches, the use of basic brick, not only in the crucible, but also in roof and sidewalls, the use of various means to feed the charge, the use of magnetite or other heavy material to construct the hearth, water cooling of bridgewall and slag skimming bay, the smelting of raw charge instead of calcine, the use of preheated air, and possibly the use of oxygen-enriched air for combustion. But the general outlines of the furnaces have not changed much except as to size. Furnaces at Hurley As shown on Fig. 1, the furnace at Hurley is 126 ft long between the longitudinal buckstays and 32 ft wide at the skewback plates. The foundation is a concrete retaining wall with piers at intervals that go deeper into the earth. Purposely the wall at the burner end of the furnace is not backed-up as tightly as the other parts of the foundation so that movement due to expansion may take place here rather than into the boiler foundations. Within these foundation retaining walls of concrete, the earth has been removed to allow the placement of the crucible brick base inside of which a silica hearth is laid 4 ft 6 in. in depth. No expansion is left in the brick base and crucible where they are in contact with the hearth. The hearth itself is of quartzite crushed to 1 in. size with fines left in the product. An 8 in. layer is laid and tamped with paving tampers to about 6 in. in thickness. Then a layer of silica flour is spread and vibrated into the hearth. This operation is repeated until a depth of 4 ft 6 in. is occupied by the silica mass onion-skinned in layers of approximately 6 in. Before firing the entire hearth is covered with broken slag to a depth of 4 in. so that a seal may be formed on the hearth. The crucible is completely faced with magnesite chemically bonded brick while the outside, against the foundation, is made of silica brick. The side-walls are carried up with silica brick in which expansion joints are left at intervals. Above the crucible the sidewall is corbelled to form a shelf on which the charge may build up along the side-walls, see Fig. 2. The arch of the furnace is sprung 20 in. silica brick, with the longitudinal centerline horizontal the length of the furnace, and some 9 ft in the center above the bath. Both straight and wedge brick are used in the construction and a thin silica mortar is troweled for joints. After the arch under heat has assumed its permanent shape, a silica slurry is spread over the arch to fill any cracks that have formed, thus giving bearing surface to the brick and preventing dust from entering the body of the arch to act as a future fluxing agent. The uptake of the furnace slopes up to the boiler entrance where a brick pilaster divides the gas stream for the two boilers. Over this flared uptake is a suspended flat arch of firebrick. The pilaster and sidewalls are constructed of firebrick but the bottom of the uptake is lined with silica brick and fettled through holes in the roof with siliceous fettling. Close to the entrance of each boiler is a brick covered slot through which water-cooled dampers may be lowered in event of boiler trouble. These water-cooled dampers are hung permanently in position ready to be lowered when needed. Flexible hoses to follow the dampers as they are lowered are connected at all times and individual chain blocks are used to lower the dampers. A pump supplying water is started before the dampers enter the heat. Charging of the furnace along the sidewalls for some 80 ft from the bridgewall is accomplished by electric vibrating conveyors fed by belt from charge storage bins above the furnace. These conveyors

Jan 1, 1954

By P. W. Bennett, E. M. Elkin

A new technique for the recovery of palladium and platinum and sludge from go12 electrolyte eliminates many of the drawbacks of the zinc-dust cementation process. In the electrolytic refining of gold by the Wohwill method, the electrolyte contains about 100 gpl gold as AuCl, and 100 gpl free hydrochloric acid. Any palladium and platinum contained in impure gold dissolve and accumulate in the electrolyte. When their concentration approaches that of gold, it becomes desirable to discard the electrolyte and to recover the gold and the palladium and platinum. As practiced at Canadian Copper Refiners until recently, discarded electrolyte was treated with sulfur dioxide to precipitate the gold. 2AuCl3 + 6H2O + 3SO2 —2Au + 6HC1 + 3H2SO4 The gold precipitate was filtered off, washed with water, and melted with scrap anodes. The wash water was added to the gold-free filtrate and treated with zinc dust to cement the palladium and platinum. PdCl2 + Zn — Pd + ZnCl2 PtCl4 + 2Zn—Pt + 2ZnCl2 The precipitate was separated and sold as Pd-Pt concentrate, and the barren filtrate and wash water were discarded. The receipts of palladium and platinum at this company were too small to warrant their refining. The process suffered from a number of disadvantages. Handling the gold-free solution was disagreeable, as it was laden with sulfur dioxide even after blowing with air overnight. Subsequent treatment with zinc dust was also troublesome. A large excess of zinc dust was required. Spray, acid mist, and vigorous evolution of hydrogen accompanied the reaction. The Pd-Pt precipitate was grossly contaminated with occluded unreacted zinc and with yellow granules of sulfur, thought to be formed by the reduction of sulfur dioxide and its derivatives. Repeated boiling of the precipitate with hydrochloric acid and washing with water decreased somewhat, but did not eliminate, the zinc. After drying overnight, the precipitate hardened to a clinkerlike mass that was difficult to grind. Grinding, handling, and packing created heavy dusting. Even weighing in an analytical balance generated dust, indicating that the powder was easily charged with static electricity. The total palladium and platinum content of the powder varied from 56 to 72 pct, with an average of 65 pct. The powder dissolved in aqua regia with difficulty, leaving a small amount of insoluble residue. However, the main drawback of the process was the strongly hygroscopic Pd-Pt product. The powder showed a marked though erratic increase in weight and a corresponding decrease in assay on exposure to air, even during the course of laboratory analysis. Such changes were the source of disagreement between Canadian Copper Refiners and the buyers of concentrate. The cause of the change in weight is believed to be hydrogen, liberated by the action of zinc dust on hydrochloric acid. Some of this hydrogen was adsorbed so strongly by the precipitate that it could not be driven off during the drying. On exposure to air it oxidized catalytically, forming water. Experiments soon showed that the entire process of treatment of discarded electrolyte then in use would have to be changed. A small quantity of apparatus was moved into the gold room, and experimentation was held to a minimum compatible with the development of a new process. PALLADIUM AND PLATINUM PRECIPITATION It was thought that zinc could be replaced with a reagent other than a hydrogen-evolving metal. Semiquantitative experiments showed that platinum and palladium could be precipitated completely from the gold-free solutions with such well-known reagents as sodium formate, formic acid, formaldehyde, and paraformaldehyde. Sodium formate was the preferred reagent, since the other three are volatile and somewhat toxic. The gold-free solutions used were those saturated with sulfur dioxide, partly freed of sulfur dioxide by aerating overnight, completely freed by boiling, as well as strongly and weakly acidic, neutral, and alkaline solutions. The reactions are complex and can be represented by these over-all equations: PdC1, + HCOONa — Pd + NaCl + HC1 + Co2 PtCl4 + 2HCOONa — Pt + 2NaCl + 2HC1 + 2CCX, Strongly acidic solutions required as much as five times the theoretical amount of sodium formate as did solutions neutralized to pH 4.5. Increasing the pH decreased the consumption of

Jan 1, 1965

By E. C. Carris

THE loading of bituminous coal mechan¬ically was recognized about the year 1900, but during the following 28 years less than 5 per cent of the bituminous pro¬duction in the United States was loaded by mechanical means. During the past i6 years, however, the usage of some form of mechanical loader has had a very rapid and accelerated growth, until at present production of bituminous coal by mechanical means has reached an all¬time high of approximately 46 per cent, and is still increasing. This rapid growth in the use of the mechanical loader has been supplemented by an increase in mechanical cleaning. The importance of mechanical cleaning of coal was recognized many years before the mechanical loader was introduced, because of the impossibility of cleaning manually the sizes below 2 in., and the increasing competition from other fuels. Utilization of mechanical loaders without mechanical cleaning on the surface for at least one or more sizes is the exception, rather than the rule. One exception is a mine that employs caterpillar-mounted mobile loaders exclusively, and mines the entire seam without any selectivity, and yet loads and ships six grades of coal of the very highest quality without mechanical cleaning. Such a fortunate situation can exist only where mining conditions are ideal, where top and bottom are exceptional and there are no impurity partings, and where there is loader height. The conversion from hand loading to mechanical loading has definitely intro¬duced many problems in the preparation plant of yesterday and in the modern streamline plant as well. Many of these problems have been solved by good, sound, conscientious initiative on the part of the plant personnel, with minor expendi¬tures; the solution taking the pattern of rearranging and improving the equipment at hand. Other problems have caused, and are causing, considerable concern and difficulty. LARGE IMPURITIES The removal of large quantities of large impurities from the lump coal, and their handling and disposal, is definitely a troublesome and costly problem. The cost of manually removing the impurities from the picking table alone, based on the actual recovered lump coal, can reach a cost of 42 cents per ton or more. In the design of future plants it would be wise to give this phase of preparation considerably more time and thought, particularly if the seam of coal contains one or more heavy partings and the mining procedure is all seam. This same caution applies to seams that may not contain heavy partings but have poor and heavy draw-slate top, which falls with the coal during the mining cycle. One of the more recent of the modern preparation plants has answered this problem by installing a rock crusher under the picking table in such a manner that the impurities can be diverted by gravity directly to the crusher. This reduces the

Jan 1, 1946

By I. C. White

ONLY two factors appear to be directly responsible for the geographic distribution of sulfur in the coal fields of West Virginia, these, are the FIG. 1. stratigraphic position of the coals in question., and the eastward or westward location of the deposits. There appears to be a progressive increase in the sulfur content of West Virginia coals from the oldest Pennsylvanian deposits in the Pocahontas, New River, and Kanawha Groups of the Pottsville Series up through the Allegheny, Conemaugh, and

Jan 9, 1919

By Karl L. Fetters

In the process of making steel in the open-hearth furnace the refining of the metal during the working period of the heat is largely accomplished through the agency of the slag. From the birth of the process until the present day steelmakers have recognized the importance of the slag in determining the composition of the metal and the quality of the product. The general relationships between slag composition and metal analysis have long been known, at least in a qualitative or approximate fashion. For examples, the iron oxide content of the slag is higher on lower carbon heats; the more basic slags are higher in iron oxide for a given carbon content; certain amounts of iron oxide and lime arc required for phosphorus removal and a high lime-silica ratio is needed if the sulphur content of the metal is to be diminished. In recent years a number of quantitative relationships involving these and other variables have been developed through plant and laboratory studies by numerous investigators in this country and abroad. The direct comparison of laboratory and open-hearth data involves the question of the degree to which each approaches the conditions of chemical equilibrium, a question which, from the open-hearth standpoint, we are scarcely yet in position to answer. And, although a considerable body of dependable equilibrium data has been obtained in the laboratory, this work has not yet been extended to cover the ranges of slag composition encountered in basic open-hearth practice. In the present study we shall not attempt to draw comparisons between data from the two sources; nor do we attempt to draw conclusions as to the approach to chemical equilibrium in the open-hearth furnace. Many of the operating variables that are likely to be erratic or unrecorded during the earlier stages of the heat become more consistent and arc more readily subject to observation and control during later stages. For example, undigested lime or ore gradually goes into solution, the rate of carbon drop levels off, and the temperature of the metal is brought under control. For these and other reasons a greater degree of self-consistency is likely to be found among data obtained during the

Jan 1, 1940

By Karl L. Fetters

In the process of making steel in the open-hearth furnace the refining of the metal during the working period of the heat is largely accomplished through the agency of the slag. From the birth of the process until the present day steelmakers have recognized the importance of the slag in determining the composition of the metal and the quality of the product. The general relationships between slag composition and metal analysis have long been known, at least in a qualitative or approximate fashion. For examples, the iron oxide content of the slag is higher on lower carbon heats; the more basic slags are higher in iron oxide for a given carbon content; certain amounts of iron oxide and lime arc required for phosphorus removal and a high lime-silica ratio is needed if the sulphur content of the metal is to be diminished. In recent years a number of quantitative relationships involving these and other variables have been developed through plant and laboratory studies by numerous investigators in this country and abroad. The direct comparison of laboratory and open-hearth data involves the question of the degree to which each approaches the conditions of chemical equilibrium, a question which, from the open-hearth standpoint, we are scarcely yet in position to answer. And, although a considerable body of dependable equilibrium data has been obtained in the laboratory, this work has not yet been extended to cover the ranges of slag composition encountered in basic open-hearth practice. In the present study we shall not attempt to draw comparisons between data from the two sources; nor do we attempt to draw conclusions as to the approach to chemical equilibrium in the open-hearth furnace. Many of the operating variables that are likely to be erratic or unrecorded during the earlier stages of the heat become more consistent and arc more readily subject to observation and control during later stages. For example, undigested lime or ore gradually goes into solution, the rate of carbon drop levels off, and the temperature of the metal is brought under control. For these and other reasons a greater degree of self-consistency is likely to be found among data obtained during the

Jan 1, 1940

By John Porter

(Cleveland Meeting, October, 1912.) Iv taking up this subject it is first necessary to define our terms. Efficiency, in its engineering usage, means the ratio between actual and theoretical results, and efficiency-records thus involve the use of scientifically determined standards with which all results are compared. Scientific management is the methods used in increasing efficiency, and includes the use of efficiency-records. Effeciency-records do not alone constitute scientific management, but they are necessary to it, and any so-called system of management which is not based upon standards and standardization is fundamentally wrong. An efficient management and efficiency-methods in management are not the same thing. There are some people who have an instinctive genius for management and accomplish results without exactly knowing how they do it. Such a manager may obtain a very high efficiency without the aid of scientifically determined standards. On the other hand, it sometimes happens that poor results will accompany the use of efficiency-records, clue to a weak or indifferent management, which fails to make use of the information acquired. Efficiency-records are only a tool, and like other tools are worthless unless used. The ordinary cost, sheet and production-statement do not go far enough. They tell what has been done, but give no information as to how well it has been done. It is true that the man who is familiar with the industry and the plant in question may draw inferences and form a general idea of good work or bad work, but it can only be a very general and hazy idea. Comparisons with previous records or records of other plants are unsatisfactory, since there is nothing to show the cause of the differences.

Jan 4, 1913

By Zay Jeffries

In this paper, it is proposed to outline a method for the determination of melting points of those metals and alloys having high fusion temperatures. The application of the method as used to determine the melting points of alloys of tungsten and molybdenum will be given. It will be seen from these results that tungsten and molybdenum form a completely isomorphous series. This is also verified by the accompanying photomicrographs. Tungsten and molybdenum have been found to crystallize in the same system namely, isometric, and the crystal units are cubes. These determinations were made by examining etching pits in the pure metals.

Jan 1, 1917

By C. W. Phillips, D. N. Frey

A commercial Ti-Fe-Cr alloy, Ti-150, exhibits a martensitic transformation on cooling and two nucleation and growth reactions, one above and one below the Mg-Mf region, on isothermal holding below the single-phase ß temperature range. The reactions were followed by metallographic, X-ray diffraction, and microhardness methods. THE rapidly expanding engineering application of titanium and its alloys makes increasingly urgent an adequate knowledge of the effect of heat treatment on this material. The work herein reported is an attempt to determine certain aspects of the behavior of a commercially available alloy, Ti-150, during heat treatment. The alloy, with a nominal composition of 2.7 pct Cr, 1.3 pct Fe, 0.25 pct 0, 0.02 pct N, and 0.02 pct C, was received in the as-rolled condition as a 3/4 in. round. Slugs 0.11 to 0.12 in. thick were cut under a coolant using a silicon carbide wheel. Preliminary work established that the alloy consists of two phases, a (hexagonal close-packed) and /3 (body-centered cubic), at temperatures below 1750" to 1775"F, and of only /3 phase at higher temperatures. The slugs were heated for 1 hr in air at 1800°F to form a single-phase /3 matrix, then transferred to molten tin (1250° to 1650°F) or lead (1150°F and below) for isothermal holding. Holding temperatures ranged from 700° to 1650°F, times from 0.001 to 23 hr. The treated slugs were then sectioned, one part for metallographic examination and diamond pyramid hardness, the other, after deep etching to remove the high oxygen surface,' for comparative lattice parameter determination and X-ray phase identification. Hardness measurements were taken on the lightly etched surfaces of the metallographic specimens; a 1000 g load on a 136° diamond pyramid was used. Five impressions on each sample were made and the average of the hardness calculated. The use of microhardness measurements to follow the course of an isothermal transformation reaction is undesirable because of the possibility of wide differences in microconstituent hardness.' They were used in this case, however, because of the small amount of material available. At the higher transformation temperatures, where the above-mentioned objection was apparent, the readings were proportioned to correspond to the estimated ratio of transformed and untransformed constituents present. At lower temperatures, resulting in much finer microconstituents, the microhardness measurements were more uniform. The standard deviation of the mean of five impressions calculated from these latter values was 4.2 DPH. Employing 2a limits (probability 0.95) the experimental error of the hardness measurements averages was 8.4 DPH. The etchant used was composed of one part glyc-erol and one part 48 pct hydrofluoric acid." Of a number of etches tried, this one appeared most satisfactory. All micrographs were taken at 500X magnification and with oblique lighting to permit easier identification of the acicular structure resulting from rapid cooling. No advantage was gained by using polarized light for metallographic examination. Phase identification and lattice parameter measurements were made with a North American Philips high angle spectrometer in conjunction with a recording potentiometer. Considerable difficulty was encountered with some of the lattice parameter measurements because of the extreme broadness of the few diffraction lines obtained from samples consisting mainly of strained, untempered, quenched structures.

Jan 1, 1953

By G. R. Purdy, J. A. Malcolm

The isothermal dendritic precipitation of y in p CuZnSn is compared with the isothermal formation of Widmanstatten a plates in p CuZn. Although both precipitates are evidently bounded by semicoherent interfaces, the dendritic shape of y evolves through smooth "sinuoidal" shape perturbations, while a-p interfaces tend to be strictly planar, or rnicroscopically faceted. An estimate of the average inter-facial free energy of cube-oriented y in p through the Mullins-Sekerka analysis indicates that it is low (of the order of 50 ergs per sq cm). Interface mication is apparently controlled by volunle dij'usion, and the observed anisotropy in growth probably results from anisotropy of inter facial free energy. Studies of the grain boundary precipitation of y in p indicate that the precipitate can grow in both $ grains, but becomes unstable with respect to the grain with which it shares a mobile semicoherent interface. Facets observed at the tips of Kurdjumov-Sacks-oriented Wid-manstatten a plates correspond to variants of an irrational hahit, near (231)0. Comparison with Hu and Smith's determination of relative interfacial free energies of a-(3 boundaries suggests that this system possesses an extremely deep o cup, which results in an ej'ective low-o zone. The possible effects of such a cup on the stability of a-p interfaces are discussed, a needles, grown during rapid continuous cooling, possess microscopically smooth interfaces, and are characterized by a high degree of' damage in the region of the boundaries. These boundaries, induced to move on tempering at 200"C, become faceted as equilibrium is approached, which seems to indicate that boundary structure and mobility in this system are dependent on the local degvee of departure from equilibrium MULLINS and sekerkal have elucidated the phase boundary stabilizing effect of surface tension. a factor not taken into account in previous treatments of morphological development. Their analysis applies to the isothermal growth of a pure spherical precipitate (planar in the limit of infinite radius) in a slightly supersaturated solution, under conditions of inter-facial local equilibrium and isotropy of interfacial free energy. More recently, several other factors which might tend to stabilize planar interfaces have received attention. These are: i) interface diffusion;4"8 and ii) slow interfacial reaction. cahn7 included a slight anisotropy in interfacial free energy, and showed that it has no stabilizing effect, but forces shape perturbations to reflect the anisotropy. shewmon4 noted that dendritic morphologies are rarely observed in solid-solid systems, and, in particular, postulated that slow interfacial reaction occurs at all boundaries between proeutectoid ferrite and austenite, except those which propagate parallel to {11 l)y planes (for Kurdjumov-Sachs [K-S] related phases). Previously, Aaronson~ had proposed interfacial reaction at the broad faces of Widmanstatten plates, and expected that the lateral motion of high-mobility incoherent ledge edges would produce planar precipitates bounded by law-mobility semi-coherent interfaces. The problem of interfacial reaction during the dif-fusional formation of precipitates has often been ignored, although it is apparent that a small component of chemical reaction must exist at any moving interface." Further, all solutions of the diffusion equations for boundary conditions corresponding to isothermal growth predict infinite growth rate at time zero, so that elements of interfacial reaction would be most easily detected at early times. However, reported deviations from diffusion control are comparatively rare," and the local-equilibrium diffusion-control model appears adequate for the description of many isothermal growth systems.'2"9 Cahn14 has treated the problem of migration of an interface which is able to reach positional energy minima, and concluded that such an interface, if subjected to a high local ther-modynamic "driving force", may migrate normal to itself without the benefit of ledges. As local equi-

Jan 1, 1968

By R. F. Slack, J. C. Draper, J. A. Younkins

In 1959, the Duquesne Light Co. was faced with the problem of moving more than 40 million tons of bituminous coal in Greene County, Pa. The coal had to travel a distance of about 4 ½ miles from a new mine portal in Rocky Run Valley to the company preparation plant and loading facilities on the Monongahela River. After careful study of this immense transport problem, Duquesne decided that the belt conveyor system described in the following pages offered the best solution. This system, now in operation, is probably one of the four or five longest permanent overland conveyor systems in existence. The general layout of the entire system is shown in Fig. I. A detailed description of the salient features of the system is presented below. THE MINE The valley of Rocky Run where the system begins is very, very narrow and very steep. It was chosen as the site of Duquesne's new mine portal because it was the only place on this particular property where the Sewickley coal seam cropped out. The valley also had two other advantages. First, it fronted on a state road and, second, it offered a site where some 4 million gallons of water could be stored for use in dust-allaying sprays needed in the mine. The company elected to construct a drift mine in the valley because this would require neither the hoisting time of a shaft mine nor the walking time of a slope mine. As part of the mine construction project, the valley was leveled by relocating its stream and filling its center with material cut from each side.

Jan 11, 1966