Search Documents

By A. A. Berk

Other Federal agencies have been coming to the Bureau of Mines for help with the purchase and utilization of fuel, largely coal, almost since the day the Bureau was created in 1910. The requests covered a wide range of fuel-economy problems and included boiler-water treatment after it became apparent that water-formed deposits on heating surfaces acted as insulators, decreasing heat transfer and impairing fuel efficiency. Dr. Ralph E. Hall, a Bureau of Mines physical chemist determined the reactions that cause adhering scale to form in boilers (7)2 and went on to introduce scientific principles into water treatment for scale prevention (8). Widespread publicity of these achievements increased the requests for help from Federal steam-generating plants. Since no other Federal agency (even those which were more directly concerned with testing water) wanted to provide boiler-feedwater service, the Bureau decided to continue to give requested help to Federal agencies, Later, the Congress endorsed such agency cooperation as an economy measure,

Jan 1, 1963

By T. W. Beck

Drilling into coal mine roof strata to install roof bolts has the potential to release substantial quantities of respirable dust. Due to the proximity of drill holes to the breathing zone of roof bolting personnel, dusts escaping the holes and avoiding capture by the dust collection system pose a potential respiratory health risk. Controls are available to complement the typical dry vacuum collection system and minimize harmful exposures during the initial phase of drilling. This paper examines the use of a bit sleeve in combination with a dust hog-type bit to improve dust extraction during the critical initial phase of drilling. A twisted-body drill bit is also evaluated to determine the quantity of dust liberated by comparison to the dust hog-type bit. Based on these laboratory tests, the bit sleeve may reduce dust emissions by one-half during the initial phase of drilling before the drill bit is fully enclosed by the drill hole. Because collaring is responsible for the largest dust liberations, overall dust emissions can also be substantially reduced. The use of a twisted-body bit has minimal improvement on dust capture compared to the commonly used dust hog-type bit.

Feb 27, 2013

"The McArthur River uranium deposit is the single richest uranium ore body developed in the world to date. The ore body’s average grade is 15% U3O8. Proven reserves are in excess of 450 million pounds. The grinding circuit is located underground. The ground ore is pumped to a surface facility where the slurry is thickened and loaded into containers for shipping to the Key Lake mill 78 kilometers to the south.The paper will briefly describe the mining method employed. The underground ore handling and grinding circuit, and surface facilities including slurry load out, wastewater treatment and the freeze plant will be described in detail. The paper will emphasize radiation and safety procedures that are followed to minimize operator exposure to radiation risks.LOCATIONThe McArthur River mine is located 78 kilometres north of the Key Lake mill. It is located at latitude 57’ N in northern Saskatchewan, within the southern boundary of the Athabasca formation. The nearest town is Pinehouse, located 320 kilometres to the south. Access to the mine is by an all weather road and by a private airstrip.HISTORYThe McArthur River Operation is jointly owned by Cameco Corporation (69.805%) and Cogema Resources Inc. (30.195%). Exploration for uranium in the McArthur River area started in 1980 by the Saskatchewan Mining Development Corporation, a predecessor company of Cameco.In 1984, a 12-kilometre long basement conductor was identified at a depth exceeding 500 metres. Systematic exploration drilling of this conductor resulted in the discovery of the P2 North deposit. Subsequent surface drilling programs from 1989 to 1992 delineated a narrow ore zone over a strike length of 1700 meters at a depth of 500 to 600 metres. At this time, geological reserves for the deposit were estimated to be 2.4 million tonnes at a grade of 5.0% U3O8 for a uranium content of 260 million pounds U308"

Jan 1, 2001

By Djavid Mohammad

Over the next several years, the storage capacity of the Metropolitan Water Reclamation District of Greater Chicago?s Tunnel and Reservoir Plan will be increased by 14.8 billion gallons through the addition of two large off-line reservoirs: the McCook and Thornton Reservoirs. The Thornton Reservoir will be constructed at the terminus of Calumet TARP System. The constructed TARP system will be connected to the Thornton Reservoir via connecting tunnels and gates systems. The connecting tunnels will comprise of: an upgradient transition tunnel, steel lined bifurcated tunnel for conveyance and control of flow, downdradient transition tunnel, and energy diffuser at tunnel portal. A large, approximately 250-foot-long, 69-foot-wide, and 40-foot-high, rock cavern will be excavated at an average depth of 320 feet to house the bifurcated tunnel system and associated six large control gates, each 12.5-ft by 28-ft wheel gate. Presented in this article are discussions about the TARP system, the Connecting Tunnels and gates Project, regional rock conditions, evaluation of reservoir?s wall stability for evaluation of tunnel penetration, and design challenges facing during design of the: rock cavern hosting the bifurcated tunnel system and gates and associated tunnels and shaft.

Jan 1, 2008

By D. E. Poole

Injury Prevention: Dependent, Independent and Interdependent In recent years, management-directed (dependent)safety programs have lost ground to the more successful self-directed (independent) programs, where employees take responsibility for their own safety. Today, with the growth of the team concept in industry, a mutual-caring (interdependent) approach to workplace safety is gaining wide acceptance. This presentation compares characteristics and results of the three progressive levels of safety responsibility and explains how to develop a successful interdependent program. The presentation will also detail the common principals that are necessary for safety excellence under any of the management styles.

Jan 1, 2000

By Douglas B. Silver

Traditional cycle theory would postulate that if you have a supply shortage relative to demand, the price will increase because buyers will incrementally increase the price they are willing to pay to ensure that their needs are fulfilled. As prices rise, more supply will be brought on and will eventually exceed demand. This supply excess will cause the price to decline as producers have to lower their prices to sell their goods. What is interesting is that cycles are simply volatility over time. Without the time factor, volatility simply goes up and down. When we add the time element, a cycle is created. This cycle can be big or small. In mining?s case, we are talking about a Super Cycle ? a big cycle. But a Su-per Cycle can be formed in two ways. It can form by either increasing the wavelength or the volatility. If these two elements are combined, a Super Cycle is formed. It is bigger than the normal cycle in terms of time duration and extent of volatility. A recent study (Fig. 1) conducted by Cuddington and Jarrett showed an interesting proof of Super Cycles and suggests that these cycles last between 15 and 30 years. So, what causes a Su-per Cycle? Is it a convergence of unrelated events or a consequence of related events? In a global community everything is related. Equilibrium theory would also take the position that a Super Cycle is a consequence of events.

Jan 1, 2008

By Sashir Estela De la Cruz

Actualmente la informática como herramienta aplicada al sector minero nacional, es importante -en tanto su empleo adecuado y racional implica alcanzar los objetivos planteados en forma más rápida y con mayor calidad. En este sentido, el presente texto describe el sistema informático que genera soporte al trabajo de modelamiento geológico para la estimación de reservas mineras, de forma que reduce el tiempo y personal empleado en dicha labor. Este sistema se divide en dos partes: estadístico y gráfico y determina la explotación de un prospecto de yacimiento minero.

May 25, 1998

By Paul J. Axtell

Two new railroad bridges in Kansas City, Missouri are founded on drilled shafts embedded into the soil and underlying shale. The uncertainty arising from the non-homogeneous, anisotropic nature of most shales, and the variability of shales across the U.S., makes it a difficult material to assign appropriate design properties. As was the case on this project, the uncertainty of foundation performance in shale can lead to overly conservative designs, particularly with drilled shaft foundations. An extensive Statnamic axial testing program was performed to verify that the load-settlement behavior of the drilled shafts would be acceptable for the intended railroad traffic. Axial Statnamic testing was applied in three increasing cycles of 927 kips, 1007 kips, and 3177 kips, respectively. The maximum movements recorded at the shaft head during each of the loadings were 0.052 inches, 0.062 inches, and 0.257 inches, respectively. The loads applied in each of the respective Statnamic tests were not sufficient to reach the capacity of the shaft; so direct comparison of measured and calculated capacities is not possible. However, evaluation of the estimated design capacity can be accomplished based on results from the Statnamic testing program by utilizing normalized load transfer relations presented by O?Neill and Reese (1999). Such comparisons necessarily require extrapolation of the data measured in the Statnamic tests following typical load-displacement response. Results indicate the Kulhawy and Phoon (1993) method for estimating side resistance in Pleasanton shale rock sockets, assuming a smooth socket, appears to agree well with observed behavior during Statnamic testing. Accordingly, the O?Neill and Reese (1999) method for estimating the toe resistance in intermediate geomaterials, assuming cohesive rock with Rock Quality Designation (RQD) between 70 and 100, appears to agree well with observed behavior during Statnamic testing. Finally, based on Statnamic testing at varying load magnitudes and normalized curves developed by O?Neill and Reese (1999), the contribution of side resistance to the capacity of a deep foundation can be determined assuming no load is transferred to the base of the foundation during lower magnitude testing. Furthermore, higher magnitude testing can provide a means to evaluate the accuracy of design end bearing calculations.

Jan 1, 2006

By Frederic Benard

PRIOR to 1936, the Ontario Refining Co. received all incoming blister copper from The International Nickel Company's smelter in the usual form of 460-lb. cakes, or slabs. These were received in open cars in lots of 250 pieces. At the refinery the cakes were unloaded onto narrow-gauge cars, for convenient handling and pickup by charging cranes. In March 1936, an investigation was started on the feasibility of transferring converter copper in the molten state from the smelter to the refinery anode furnaces, a distance of 1 ¼ miles. Although common in steel practice, the transportation of blister copper in this form had not previously been attempted and a preliminary study of the various factors involved was therefore necessary. For this purpose, a series of experiments was made in which molten copper, removed at different stages during the furnace cycle, was held in a small portable holding furnace. This vessel was essentially a refractory-lined steel cylinder provided with ports for filling and emptying, heated by an oil burner. Dimensions of the steel shell were 3 ft. 10 in. diameter by 7 ft. 3 in. long, and thickness of refractories depended on the design and combination used for the particular experiment. The vessel was filled with approximately 2 ½ tons of copper at a predetermined temperature, the lining having been preheated to a definite point by means of an oil burner. All openings were well luted and temperature readings were made every 15 min. by means of an immersion-type thermocouple. In this manner the rate of heat loss resulting with different refractory design could be developed. The ratio of exterior surface to weight of metal was taken into consideration in comparing the experimental results with what might be expected for a full-sized unit, and observations were also made on type and degree of slag accretion. It was not possible to get as much information on this latter point as desirable, but all evidence showed that the problem would be control of slag build-up rather than attack on refractories. From the information derived, and in consultation with the engineering staff of the supplying company, an order was placed for the first

Jan 1, 1938

By Tony Moore, Peter Riccio

"MMG (Minerals and Metals Group) operates the LXML Sepon’s mineral processing facility located 40 kilometers north of the town of Sepon, in the Savannakhet Province, Lao PDR. The Sepon copper plant produces 70,000 tons/year of LME grade A copper cathode using leachautoclave- SX/EW-flotation technology (Baxter et al., 2003). Pyrite recovery in the flotation circuit is critical to the operation, as it is used to generate acid and soluble ferric ion for the leach circuit. Low pyrite recovery has been an on-going challenge in the flotation circuit. Final tailings characterization work done by Ian Wark Research Institute (Bassell et al., 2006) showed that the pyrite losses to the tailings are made up of a combination of coarse liberated particles and finer particles that have been coated by clay fines.In December of 2005, a joint Cytec-MMG technical program was initiated to address the pyrite recovery issue. A series of diagnostic tests were performed in the Cytec Stamford Research Facility using synthetic plant water showing that the collector was precipitating as a metal salt and was unavailable for mineral attachment. The tests also identified several collector chemistries that would likely be robust in the low pH (< 1), high dissolved metal ion environment and will not complex with metal ions in solution. With the support of the Sepon on-site engineers, an extensive, successful laboratory program was completed, which was subsequently followed by on-plant testing that showed a step wise improvement in pyrite recovery.INTRODUCTIONLow pyrite recovery has been an ongoing problem in the flotation circuit at Sepon. Sulfur recovery (indirect measure of pyrite) was improved from 40% to 65%-75% in mid-2005 when on site laboratory work confirmed that AERO® 8045 Promoter was a more effective collector then AERO® 407 Promoter. However, sulfur recoveries above 65% could never be achieved. Sepon requested the Ian Wark Research Institute to complete a surface analysis study using Scanning Electron Microscopy, X-ray Photoelectron Spectroscopy, and Time-of-Flight Secondary Ion Mass Spectroscopy to determine if clay coated pyrite played a role. It was concluded that the pyrite losses to the tailings are made up of a combination of coarse (+ 100µm) liberated particles and finer (-74µm) particles that have been coated by clay fines. The majority of the losses appear to be due to the former. In December of 2005, a series of diagnostic tests were performed in Stamford using synthetic plant water in order to identify what chemistries would likely be robust in the slimy low pH and high dissolved metal ion solution environment. Results showed that several chemistries would not complex with ferric, ferrous or copper in solution and therefore should perform well in the Sepon flotation. The incumbent collector, AERO® 8045 Promoter was complexing with metal ions in solution. This resulted in the collector not being available for adsorption onto pyrite."

Jan 1, 2011

By G. K. Jorgenson, S. H. Chung

"IntroductionThe SABREX Blast Modelling Program was developed jointly by the companies of the ICI Explosives Group, of which C-I-L Inc. is a member. SABREX (Scientific Approach to Breaking Rock with Explosives) is a modular computer program which incorporates new technology with a number of tested programs that have been in use world wide.SABREX predicts the performance of blasts in terms of (I) fragment size and distribution; (2) muckpile profile and face velocity; (3) grade fracture; (4) collar breakage; (5) a rupture envelope which depicts crack penetration behind and beneath blastholes; and (6) a complete cost analysis including explosives, drilling and accessory costs. The predicted blast results are displayed as dynamic colour graphics and in tabular form.SABREX uses data on the detailed geometry of the drilled and loaded pattern, detonation characteristics of the explosives and the dynamic properties of the rock to generate blast predictions. SABREX blasting calculations take into account the effects that shock and quasi-static pressures exert on the rock around the blastholes. While physical effects occur very rapidly in rock blasting, it is possible to view and model the sequence of events as discrete sections.The program can be run on a microcomputer and is currently operated by C-I-L technical service staff in Canada for the use of drilling and blasting operators.Figure I is a diagram representing the modules of the program and associated technology that is used to complement the program.Any, or all, of the modules may be used in a particular study or blast optimization. Because the BOBCAT module of the SABREX program has been described in previous papers(7.8.9), this discussion will concentrate on the newer modules: CRACK, HEAVE, RUPTURE ENVELOPE and to a limited extent, KUZ-RAM, which present a more detailed picture of the blasting process.Each of these modules is discussed in terms of the information they offer the operator in analyzing the blast. Specific examples of recent usage in Canadian mining situations are included to illustrate the ability of the model to produce practical results that can assist in optimizing actual blasting operations or solving problems that do exist."

Jan 1, 1987

By J Wallis

The stability of a raise bore is often assessed using the rock mass classification system published by McCracken and Stacey as a modification of the Q system. Often the assessment is done using a spreadsheet to manipulate geotechnical log(s) of boreholes. This paper discusses the inherent difficulties with this approach. Recent work by others to provide guidelines to the classification system is discussed. A recent example of the design and raise bore performance at Macraes Gold Mine, New Zealand is presented. A key issue is that a visual assessment of the drill core and/or core photographs is necessary to æground-truthÆ the classification.

Jan 1, 2008

By JeffreyS. Vipperman, Daniel R. Babich, EricR. Bauer

In response to the continuing problem of noise induced hearing loss NIHL among mine workers, the National Institute for Occupational Safety and Health NIOSH has conducted numerous noise surveys in coal preparation plants. The research, consisting of worker dose monitoring, task observations, and equipment noise profiling, was completed in eight separate preparation plants. Worker dose monitoring was conducted for three shifts in most cases. Workers experiencing higher than allowable doses were task-observed for one full shift to correlate dose to noise source(s). Finally, noise levels on all floors, and in lunchrooms and control rooms, were characterized. Results indicate that only workers who routinely spend a significant portion of their shift in the plants (away from the control rooms) are susceptible to overexposure from noise. Certain pieces of equipment (screens, centrifuges, sieve bends) are the loudest primary noise sources responsible for the worker noise exposures.

By Dunlop GA

Pilot Plant confirmatory testing of the treatment route developed in the Metallurgical Laboratory is an essential factor in the development of complex ore bodies. Objectives should be well defined to permit the efficient planning and cost effective operation of the pilot plant project. The primary objective for the pilot plant should be to confirm the viability of the developed flowsheet on a continuous basis, examining only major variables such as ore types, quantum changes in grind, comparison between bulk and sequential flotation circuits, use of flotation columns, evaluation of autogenous grinding and production of samples of concentrates for market evaluation. Secondary objectives may include the collection of engineering design data and the production of a comprehensive report to Bankable Document standards to provide technical support for capital financing. The complexity of the ore body and the scale of the final operating project together with the pilot plant objectives will determine the extent of the pilot plant operations. The level of expenditure associated with a pilot plant can vary, in total cost and as a percentage of the total development capital investment required to take the prospect from exploration to a producing mine. Factors contributing to expenditure are discussed. Associated with cost considerations is the level of confidence mining company investors can have that their capital investment will return dividends.

Jan 1, 1990

By S. E. Phillipson

During the course of evaluations by the Mine Safety and Health Administration’s Roof Control Division, the controls on ground instability were investigated at surface and underground limestone mines throughout the eastern and southern United States. Structural geologic features, including joints and faults, were identified by basic geologic mapping as primary controls on highwall and back instability in surface and underground limestone mines. By comparing the spatial orientation of discontinuities and internal angle of friction with the orientation of highwalls on a stereonet, the potential for sliding, toppling, and raveling failures was evaluated in a semi-quantitative fashion. Structural geologic mapping identified faults and joints, which dismembered the back and were associated with ground instability, in underground mines. This paper documents the importance of recognizing structural geologic controls on ground stability in limestone mines, advocates basic geologic mapping as a critical component of ground control programs at surface and underground limestone mines, and provides examples of simple stability evaluations using the stereonet method.

Jan 1, 2006

By M. Ayhan

Drums of a modern longwall shearer are manufactured to include various constructional features conveying extracted material onto the face conveyor as efficiently as possible. Designing a drum with a conical shell or with reduced vane length, consequently with a stepper vane angle, is the most widely employed method in an attempt to increase loading efficiency. This study compares loading performances of two such drums, one having a conical shell with modified loading vanes, the other with a cylindrical shell with reduced vane length. Firstly, the loading performances of drums are predicted and the maximum haulage rate attainable with the drums are calculated. Then the performances of drum are compared by long-term comprehensive underground trials with coal shearers under similar conditions during the production operation of Park Termik Cayirhan coalmine in Turkey. Although higher loading performance is predicted for cylindrical drums, the in situ trials point out that Globoid drums have a slightly higher loading performance than cylindrical drums. Furthermore, the relationship between operational variables, i.e. extraction height, sumping depth, haulage rate and in situ loading performance, were investigated statistically on the basis of data gathered during the underground trials. Keywords: longwall mining, shearer drums, loading performance.

Jan 1, 2006

This paper presents an analysis of the production data for the period 1861 - 1953 from hydrothermal gold-silver deposits of the Hauraki Goldfield. To directly compare the metal content of the deposits a figure of ounces of gold equivalents (oz gold equivalent) is calculated from the value of the gold-silver bullion produced from each deposit. Frequency distributions for ore tonnage and oz gold equiv. appear to be lognormal and show a high proportion of very small deposits, with 90 per cent less than 100 000 tonnes. The deposits when plotted in order of size fall roughly on a smooth curve which suggests that the size distribution is not random. A large proportion (68 per cent) of the total gold-silver extracted from the Hauraki district was contained in the largest deposit&nbsp;û Waihi. A technique used for predicting undiscovered mineral resources is ZipfÆs law, which relates the size of an item to its rank order. The figures for ounce gold equivalents from the major Hauraki deposits fit ZipfÆs law remarkably well. Taking Waihi at 6.8 million oz gold equivalent as the rank one deposit, Thames is number five and Karangahake number seven. A Zipf plot indicates that down to rank 100 (68 000 oz gold equivalent) only 28 per cent of the total gold-silver resource in the Hauraki Goldfield has been extracted. A further 72 per cent or 25.4 million oz gold equivalent, including the deposits of rank 2, 3, 4, 6, 8, 9 and 10, are undiscovered. However, since some deposits will be deeply buried under younger rocks and others will be under the sea only a proportion of the total resource will be discoverable.

Jan 1, 1981

The Hill 50 Gold Mine is situated at Boogardie, 3 miles on a bearing of 295 degrees from; Mount Magnet township. Mount Magnet lies 300 miles north-north-east of Perth, Western Australia (Fig. 1).The older workings of the mine may be identified with those of Sirdar, Gold Mining Lease 696M The Sirdar had been worked before 1902 though no records remain, and irom 1903 to 1912 about a thousana tons at a grade of 6&apos; 2 dwt. was extracted annually; by the end of 1918 6,225 oz. of gold had been obtained from the milling of 17,852 tons of ore. In view of these yields, and the length and width of the lode, this mine was early recognized as one of the most promising in the district. From 1919 to 1924 the ground,including G.M.L. 1282M, was held as Mt. Zion G.M.L. 1183M.The Hill 50 Gold Mine N.L. company took up the workings as Hill 50 G.M.L. 1282M in 1934 and have continued operations to the date of writing. To the end of 1956 the Hill 50 Gold Mine had yielded 982,106 tons of ore for a return of 448,&apos;602 fine oz. of gold.The mine has been described by: J utson (1915), Feldtmann (1920), Johnson (1949), and Finucane (1953). Finucane (1953) details the mine structure to a depth of 414 ft. The author was able to examine the mine to a depth of 1305 ft. Detailed main level mapping to the 1060 level and a detailed surface examination have revealed aspects of the structure which were previously obscure.

Jan 1, 1960

By C. G. Anderson

"As demand for copper and precious metals continues to grow, the need to develop new supplies increases. In the imminent future, the new large global ore bodies are more complex, with enargite, tennantite and tetrahedrite as the abundant contained mineralogy. These resources also contain considerable gold and silver. As such, direct treatment by conventional smelting is prohibitive due to the potential environmental impacts and copper quality issues. This paper outlines the effective application and associated economics of industrially proven Alkaline Sulfide Leaching (ASL) hydrometallurgical technology to an enargite concentrate for selective removal and recovery of arsenic, antimony, gold and silver, leaving a clean high-grade copper concentrate. The fundamentals behind the technology are described, along with those of hydrometallurgical arsenic fixation and stabilization. Flowsheets and unit operations are elucidated, along with an in-depth economic analysis. INTRODUCTION Hydrometallurgical methods can be employed for treatment of gold-, arsenic-, antimony-, tin- and mercury-containing materials, concentrates and ores, as well as complex ones containing any number of metals (Conner & Anderson, 2013). The alkaline sulfide leaching (ASL) system is one of these. It is essentially a mixture of sodium sulfide and sodium hydroxide with other meta-stable alkaline species as required. This is a unique hydrometallurgical system beause it is a very selective lixiviant for the distinct leaching of tin, gold, antimony, arsenic, tellurium, silver and mercury (Anderson, 2000, 2001a, 2001b, 2002, 2003, 2012, 2014; Anderson & Twidwell, 2008a, 2008b, 2010; Anderson et al., 2004, 2005; Glazkov & Tseft, 1961; Gnatyshenko & Polyvyanni, 1961; Nadkarni et al., 1975; Nadkarni & Kusik, 1988; Polyvyanni, 1963). Worldwide, ASL technology has been employed industrially in the former CIS, China and the United States for the production of antimony (Anderson et al., 1992, 1994; Anderson & Krys, 1993; Holmes, 1944; Kaloc, 1967; Nordwick & Anderson, 1993; van Stein, 1971)."

Jan 1, 2015

By D. A. Bruce

The Deep Mixing Method is a very valuable tool for combating problems related to in situ soil treatment, improvement, and retention. Many different variations are used throughout the world, and there is a correspondingly rich technical literature on the testing and properties of the treated soil. This paper provides a synopsis of these aspects.

Jan 1, 2001