Search Documents

By T. Shi, Q. Yuan, S. P. Vanka, B. G. Thomas

"The quality of continuous cast steel is greatly affected by fluid flow in the mold region, especially involving transient phenomena. Mathematical models are being applied to investigate many different aspects of these phenomena, but their accuracy must be validated before they can be applied with confidence. As part of a long-term effort to develop and apply comprehensive models of the continuous casting process, this work evaluates the relative accuracy of models of three different fluid flow phenomena in continuous casting through comparison with measurements.Firstly, transient flow simulations of velocities in the mold region are compared with digital particle image velocimetry (PIV) measurements in a single phase water model. Large-eddy simulations (LES) are found to reasonably match the flow measurements, including transient flow variations, except at long time scales, which could not be modeled owing to the excessive computation costs. The standard K-e model produced very good agreement with time-averaged velocities for relatively little computation time, although it is inaccurate at predicting the transient variations. Secondly, particle trajectory calculations are compared with water model measurements to study the distribution and flotation removal of inclusion particles. The LES model was able to match the measurements both qualitatively and quantitatively. Thirdly, steady, multi phase flow computations are compared with flow patterns observed in both a water model and an operating steel caster with argon gas injection. For the same conditions, the water model and steel caster produced very different flow behavior. The computational model was able to match the measured flow patterns in both cases.This work suggests that computational flow modeling has the potential to match real processes as well or better than water models, especially when complex related phenomena such as particle motion and multiphase flow are involved. Much work is still needed to further improve the models and to apply them in parametric studies."

Jan 1, 2001

By Albert F. S. Seboukens

A 5;6 MVA pyrometallurgical demonstration-scale pilot plant was commissioned at Mintek, South Africa, in 1994, using lead blast-furnace slag and coke as raw materials. The plant included a.d.c. power. supply, two plasma-arc furnaces' and an ISP lead-splash condenser. Slags containing typically 12 per cent zinc oxide and 3 per cent lead oxide are produced as a waste during the smelting of lead in a blast furnace. These slags are a potential: resource for the recovery of lead and zinc. During 1994, about 600 t of lead blast-furnace, slag was proceced through the pilot plant using the Enviroplas process. Zinc and lead oxides were reduced to their respective metals, volatilized, and collected in an. ISP lead splash condenser. Prime Western grade zinc and slags disposable in accordance with current US legislation, were produced. Zinc condensation efficiencies of about 80 per cent were achieved.

Jan 1, 1995

By Jingyuan Wang, Hengyi Zhang, Peng Lan, Ruitian Zhang, Jiaquan Zhang, Yang Li

"For the determination of mould taper and wall thickness, a 3-D numerical model of ingot-mould-hot top system has been made to evaluate the related ingot solidification process and the final soundness. The effect of mould wall thickness and the taper of its hot faces on the thermal history and the as cast structure of steel ingot has been revealed through the numerical simulation. It is shown that the ingot soundness can be improved remarkably by increasing the mould wall thickness, which is possibly beneficial to the mould life as well owning to an improved mould thermal state. The mould taper is vital to the ingot soundness but much less coherent to the mould temperature profiles. Under given casting situations, a larger mould taper can lead to a less intensity of the shrinkage porosities at the top part of ingot.IntroductionIngot casting is still one of important processes for steel production, which is adopted especially for the supply of large-sized semi-products of high quality special steels. The understanding to the solidification process is vital to both the yield improvement of casting production and the quality control of steel ingots, such as their soundness and homogeneity.The ingot processing and service performance are closely related to its defects, such as porosities and pipes[1,2], which are the most common but serious defects during ingots casting. In the late 1960s, Mahadevan and Murthy et al.[3], Irani and Kondic[4] began to analyze criteria for the prediction of shrinkage porosities in light metal casting. In 1980s, Niyama and Uchida[5], Hansen and Sahm[6,7] et al have successfully presented some related porosities and pipes criteria for steel casting. At the same time, numerical solidification simulation was well developed and applied to ingot quality studies[8-10]. However, due to the quick development of continuous casting, less emphasis has been given to the further study on ingot casting process. There leaves much work to be made for the comprehensive understanding to ingot quality improvement and the mould design by the aid of modern solidification technology[11, 12]. In this paper, the effects of mould taper and wall thickness on its thermal history, ingot solidification and the final soundness are numerically studied through solidification simulation, which has been adopted in mould design and industrial production of both the mould and its steel ingot."

Jan 1, 2012

By R. Steven Izatt

Green chemistry principles will be discussed, and examples will be given of the use of Molecular Recognition Technology (MRT) to selectively separate specialty metals such as cobalt, nickel, bismuth, rhenium, molybdenum, indium and germanium from various primary and secondary feed streams. Recovery of these metals has numerous advantages including (i) conservation of valuable resources, (ii) prevention of environmental damage, and (iii) elimination of capital and operating expenses due to re-processing or disposal of metal-bearing streams.

By M Philip Schwarz

"This paper reviews the status of computational modelling of a variety of common metals reduction processes, namely the blast furnace, rotary kiln and fluidised bed, and one new process not yet commercialised, namely smelting-reduction as in the HIsmelt Process. In each case, the last decade has seen the emergence of the capability to simulate the processes using multi-phase reacting computational fluid dynamics techniques. In some cases this capability is still in the process of being developed, and the next few years will see the maturing of the modelling techniques. As they become established, it will be possible to apply them to further refine the older technologies such as blast furnaces and rotary kilns, and assist in the optimisation, commercialisation and acceptance of the newer technologies such as fluidised bed and molten bath reduction. The development of a computational fluid dynamic model of bath smelting-reduction is described in some detail to illustrate how a large number of complex and interacting phenomena can be successfully simulated within a CFD framework. IntroductionPyrometallurgical reduction processes, such as the iron blast furnace, have become increasing more sophisticated through the centuries, so that today they are often highly efficient. There are continuing pressures, however, to refine existing processes and develop new ones. The imperatives are often economic, given that the long-term trend in the price of metals is always downward. In recent times, there has been the additional need to improve the environmental impact of metal production. Given that they almost inevitably require the use of carbon, metal reduction processes are large sources of greenhouse gases, and even a relatively small improvement in efficiency can be valuable in reducing CO2 production. Local environmental issues, such as the need to control of particulate emissions, are also driving incremental improvements in equipment.In addition to the economic and environmental drivers mentioned above, new process development is also being driven by the need to process new ores, and the need to produce unrefined metal in a form more compatible with alternative routes for downstream processing. An example of the latter is the production of DR! (Direct Reduced Iron) as a feed for EAF Electric Arc Furnace) in mini-mills.Further improvement of processes that have already been honed by continual plant experimentation over many years is not an easy task. To deliver further gains in efficiency, throughput, or product quality requires a highly sophisticated tool: one such tool· is computational modelling."

Jan 1, 2001

By Yuanbing Ling

Keywords: Calcium sulfate, Sulfuric acid, Phase transformations, Thermodynamic analysis As part of a boarder research project, seeking the development of a cost-effective process for direct production of the high value material, -calcium sulfate hemihydrate, from sulfuric acid at atmospheric as opposed to elevated pressure conditions, the fundamental work presented here has been undertaken. This includes experimental monitoring of phase transformation reactions and thermodynamic analysis of the relationships among the various phases, namely, calcium sulfate dihydrate, hemihydrate and anhydrite in aqueous sulfuric acid solution at temperatures ranging from 20oC to boiling point.

Jan 1, 2004

By M. W. Kennedy

Prediction of the thermal duties of copper coolers in freeze lined furnaces is challenging. Where copper coolers are immersed in liquid slag the heat transfer is often defined by a natural convection cell immediately adjacent to the wall, in the absence of other factors producing forced convection. Slag coolers are typically not fully immersed, slag temperature, liquidus and superheat can vary, and bath levels may change significantly with batch tapping, leading to substantial variations in radiation heat fluxes. Radiation heat transfer is discussed with reference to the non-obvious impact of slag liquidus on radiation losses in the exposed cooler sections. Reference is made to literature and the results of analytical and FEM models.

By Takahiko Okura

Japanese non-ferrous industry introduced large-scale smelting plants along seashores for overseas concentrates with increasing demand of metals around 1970s. Although serious environmental pollution became obvious, with economic growth, the industry got rid of pollution by installing new processes and improving operation technologies. At present, over 99.8% of sulfur input to smelters is fixed as stable compounds. Through those decades Japan had steep rises of oil prices, sudden change of exchange rate, and inadequate treating charges, we were faced to consider the closure of smelters. The industry has survived by increasing productivity, saving energy and reducing manpower. Furthermore the industry made great effort to recycle valued metals from scraps and wastes for the resources-recycling society. Academic research also contributes to support these individual technologies. Thus the industry has fostered world-acclaimed technologies in terms of efficiency and energy conservation. This paper presents technology development and environmentally-benign sulfide smelting processes.

By K. Lillkung, O. Forsen, J. Aromaa

"The dissolution rates of Pt, Pd and Rh in 250 g/L NaCl solution were calculated from the current densities determined by polarization curves and potentiostatic measurements measured with wire electrodes at atmospheric pressure. The results achieved with the two methods were similar. The dissolution rates at the corrosion potential were in the order of few nanometers per hour. The polarization curves indicated that to achieve dissolution rates required for economical operation on an industrial scale, the samples need to be polarized to higher potentials. When polarized to higher potentials, the metal dissolution rates were in the order of micrometers per hour. As the Tafel slopes of the metal dissolution region are fairly steep, the potential affects the dissolution rate greatly. Based on the activation energies, the dissolution reactions were controlled by a charge transfer step.IntroductionPlatinum group metals (PGM) have some very unique properties such as their inertness, giving excellent corrosion resistance, and a high melting point. At the same time, these factors make the refining of these metals very challenging. The main applications where PGMs are used are different catalytic converters, mostly in automotive catalysts. The used catalysts are also an attractive secondary source of PGMs. The exact concentrations of PGMs in catalysts vary widely depending on the manufacturer, the age and the capacity of the catalyst. The concentration of Pt in a new catalytic converter range from 300 to 1000 ìg/g, Pd from 200 to 800 ìg/g and Rh from 50 to 100 ìg/g [1]. Precious metal catalysts usually consist of a coat of the metal supported on ã- alumina. The recovery of metals from automotive catalysts has received much attention during the last few years [1-3]. In the near future, the use of PGMs in fuel cells is predicted to increase the amount of secondary PGMs available [4]."

Jan 1, 2012

By José R. Parga

In some parts of the Comarca Lagunera with population of about 2.5 million people, situated in the central part of northern México, chronic arsenic poisoning is endemic and severe adverse effects attributed to As exposure have been reported. Lifetime exposure to arsenic will develop classical symptoms of arsenic poisoning such as skin pigmentation changes, gastrointestinal disturbances and neurological changes. There are several methods available for removal of arsenic from well water in large conventional treatment plants, however a very promising electrochemical treatment technique that does not require the addition of chemicals or regeneration is Electrocoagulation (EC). The EC operating conditions are highly dependent on the chemistry of the aqueous medium, especially conductivity and pH. In this study, Powder X-ray Diffraction (XRD), Scanning Electron Microscope (SEM), and Transmission Mössbauer Spectroscopy (TMS) were used to characterize the solid products formed at iron electrodes during the EC process. This study will provide an introduction to the fundamental concepts of the EC method. Finally the results of this study suggest that the presence of maghemite and magnetite particles can be used to remove arsenic (III) and arsenic (V). In the field pilot plant scale study more than 99% removal of As species from groundwater is achieved.

Jan 1, 2005

By Jay S. Gunasekera

Metal parts are traditionally processed by either filly-liquid (e.g., casting) or filly-solid (e.g., forging) state. Semi-solid metal forming incorporates elements of both casting and forging. In 1991, Gunasekera(5) developed a model illustrating the influence of flow stress by the liquid fraction. The result fits Kiuchi's (1979)(7) experimental data quite well. This model assumed the liquid part is surrounded by solid as small pockets inside the material, which is opposite to the real practical situation. Since the melting usually first happens at the grain boundary, it is better to treat the semi-solid material as small metal crystal surrounded by liquid.

Jan 1, 1997

By Mikko Loponen

Outotec has developed an operator training simulator (OTS) platformsuitable for various hydrometallurgical processes. The complete solution is run in the cloud, where virtual client instances can be managed on-demand. The aim is to build a generalizable model that produces coherent results even when operating outside of ideal parameters, allowing the operator to train in unsteady state conditions such as start-up and shutdown. Complex software products are commonly associated with significant development time and cost. Utilizing modular software architecture, only the control system and processmodel are tailored for theOTS,whereas modules such as user administration and cloud-based client machine spawning can be imported, shortening development time. A generic acidic pressure oxidation process (POX) operator training simulation consisting of feed preparation, autoclave, dual-stage flash evaporation and off-gas scrubbing is described. Process is simulated using Outotec HSC Sim 9 process simulator and controlled by Siemens Simatic PCS7 control system.

By Guan-Yong SHI, Cong Wang, Zhi-he DOU, Ting-an ZHANG, Shi-gang FAN

Based on the pre-works, this paper proposed a new short stage process of the intensify aluminothermy reduction by the stage to prepare high titanium ferroalloy with low O and Al contents. We investigated the effects of Al and Ca and Si combination reduction agent, slag type and step-up reduction conditions on the Al content and distribution in the alloy. The results show that the step-up reduction can not only reduce effectively the oxygen content in the alloy, but also reduce effectively Al content. For instance, the oxygen content in high titanium ferroalloy is within 1%~4%, and the Al content is within 1%~5%. Its quality reaches the requirement of high titanium ferroalloy prepared by remelting process.

Jan 1, 2015

By E. W. Lithgow

Commercial volumes of nickeliferous laterite ores overlie part of a 90 km long belt of peridotites in central Dominican Republic. Protores are serpentinized harzburgites and dunites, with lesser serpentinite. The ore mineralogy consists mostly of goethite, serpentine-group minerals, quartz and poorly crystallized, x- ray amorphous materials. Minor constituents are hematite, gibbsite, olivine and enstatite. In the Ore Dressing plant the mine feed is subjected initially to proper sizing and blending to produce a homogenized mix. Subsequent drying and upgrading, by selective crushing and screening of rock fragments through a Barmac circuit, complete preparation of the ore for pyrometallurgical processing.

Jan 1, 1993

By S. M. I Kytö, J .. K. Mäkinen, K. Saarhelo

"At the Outokumpu Oy Harjavalta Copper Smelter the control philosophy of the flash smelting process has been changed from the slow feed-back control to feed-forward control. This is important as the fluctuations in the flash smelting furnace matte grade and slag temperature are desired to be minimized.The system is based on a specially designed automatic sampling device and the Outokumpu Courier 20 on-stream X-ray fluorescence analyzer. A microcomputer-based Analyzer Operator Station (AOP) controls the system and calculates the process parameters for the furnace from the analyzed chemical composition and other existing data.A considerable reduction in the deviation of the matte grade and slag temperature has been gained. This has resulted in conservation of energy and refractories, lower copper losses and higher through-put in the flash smelting furnace and converters.1.0 IntroductionThe flash smelting technology for copper concentrates was developed at the Outokumpu Oy Harjavalta Smelter soon after the World War II. The incentive for this development was shortness and high price of any form of energy. The fact that smelting can be carried out autogenously, without external energy by utilizing the latent heat of sulfide combustion was known decades before, but Outokumpu Oy was the first company to take the advantage of this knowledge in practical operation. A further advantage of this technology was that the SO2 containing gases suited well for sulfuric acid production, thus minimizing the detrimental effects on the environment (1).The very heart of the flash smelting process is the reaction shaft of the flash smelting furnace (see Appendix I). Heating up of the dried feed mixture, dissociation of several compounds, ignition and oxidation of the feed take place very intensively in the reaction shaft during 2 - 3 seconds, which the fine grained particles reside in the reaction shaft. A very accurate control of the amounts of the feed materials as well as of oxidizing gases, fuel, etc. is of primary importance."

Jan 1, 1989

By Jagdish C. Agarwal

Although copper ranks very low in the order of abundance of elements in the crust of the earth, it has been one of the first metals utilized by mar, at his emergence from the Stone Age, about 10,000 years ago. Use of copper for weapons, tools, utensils and ornaments dates back to the twilight of history, 6,000-5,000 B.C. Native copper outcrops and the malleability of the metal explain its very early use by the cave-dwellers. The working, melting and extraction of copper from its minerals are among the oldest metallurgical achievements of the human race. The oldest complete smelting installations for the extraction of copper from its minerals, dated about the fourth millenium B.C., were recently discovered in the Timna Valley, Wadi Arabah, Israel. (1) The history of the developments of the extractive metallurgy of copper has been adequately reviewed recently. (2,3) The center of copper production migrated from the Eastern Mediterranean to Northern Europe (Mansfeld, Germany, Swansea, Wales) towards the end of the Middle Ages (1500 A.D.). The production of the metal was boosted tremendously in North America since the end of the nineteenth century (Fig. 1).

Jan 1, 1976

By W. D. Keller

Scanning electron microscopy (SEM) accompanied by X-ray energy dispersive analysis (XES) is a useful tool in process clay mineralogy. The texture of kaolin, illustrated by SEM, gives a clue to its mode of genesis and probable industrial application. One type of kaolin, originating dominantly by weathering, has an open texture, slakes readily, and is used for filling and coating paper. Another type, in contrast, originates by diagenesis of Al-silicate sediments, and spectacularly resists slaking, thereby enabling it to maintain its bulk density and controlled size and shape of particles after crushing and moistening; this meets an important requirement for the manufacture of refractories. Ratios of elemental Al:Si that may be rapidly determined by SEM and XES yield information on the origin and purity of bauxite and bauxitic clays, and aid in quality control and processing of them. SEM of dissimilar textures of quartz, as in chert and novaculite, are evidence for geothermometry on a stratigraphic scale that is potentially useful in delimiting thermally favorable or unfavorable areas for hydrocarbon exploration, and possibly for unexposed metallic ore deposits.

Jan 1, 1982

By M. T. Thomas

Sufficient development of the X-Ray Photoelectron Spectroscopy (XPS), the Auger Electron Spectroscopy (AES), and the Secondary Ion Mass pectroscopy (SIMS) has made these instruments ideal for solving problems related to mineral processing -particularly gold ore processing. XPS can determine both the surface composition and chemistry of ores and tailings, and the various phases within either of them. AES can also determine surface composition with the further advantage of having greater spatial resolution so the surface chemistry associated with specific minerals in the ore can be identified. This identification helps to clarify why some minerals pass through a chemical process unaffected, while others can be successfully treated. SIMS has an elemental sensitivity from one to four orders of magnitude greater than XPS or AES which makes it useful for detecting the presence of some elements in very low concentration (parts per million).

Jan 1, 1981

By Jilai Xue, Jun Zhu, Baisong Li

"TiB2-C/C Function Gradient Materials (FGM) is used in cathode materials to improve aluminum wettability and melt penetration in aluminum electrolysis. In this investigation, FGM was tested for use as part of the cathode materials, where a 10 mm thick TiB2-rich layer was on the top as an Al-wettable surface, the TiB2-C layers in the middle as a gradient layer and the carbon on the bottom as a base. Electrical resistances ofFGM were determined in the temperature range of25- 9600C in argon atmosphere. The results show that the present of TiB2-C gradient layer can reduce the open porosity and the electrical resistance of the cathodes materials at elevated temperatures. The cathode samples after aluminum electrolysis usually demonstrates an increase in electrical resistance, but the application of FGM layer can compensate such an increase for certain extend due to less variation in porosity and lower the level of melts penetration.IntroductionCarbon is still used for aluminum reduction cathodes dominantly, but it has a poor wetting properties by liquid aluminum and the anode-cathode distance has to be kept about 4-5cm with an additional 1.3-2.0 V voltage drop [l]. TiB2 has better wettability by liquid aluminum with higher electrical conductivity and stronger chemical resistance to the electrolyte attack. And the wettability ofTiB2-C composites cathode on liquid aluminum can be also improved, while liquid aluminum can completely wet the cathode surface ifTiB2 content exceeds 27% [2-4]. However, during the process of TiB2-C composites cathodes preparation and aluminum electrolysis, the deformation by temperature variation or sodium penetration are great disparity between TiB2 and carbon due to their physical properties difference. This will accelerate the cathodes cracking and deterioration."

Jan 1, 2013

By Nathan A. Tiner

Sulfuric acid anodizing process is extensively used in many industrial and consumer products to provide corrosion resistance to aluminum alloys. The anodic coatings produced consist of amorphous alhnum oxide with a pornus structure which is easily sealed and colored with dyes. The coatings may contain defects due to surface flaws, canposition and microstructure of the aluminum alloy, and/or due to the anodizing process conditions. This paper will describe the techniques used in anodizing process, various defects which may be produced in anodic coatings and the methods to control them.

Jan 1, 1992