Search Documents

By Zhang Libo, Wang Xin, Peng Jin-hui, Ju Shaohua, Guo Sheng-hui, Xu Lei, Huang Meng-yang

"China is lacking high grade titanium ores. This work intends to leach impurities such as Fe, Ca and Mg from a low grade titanium ore, to increase the grade. The original material contained 65% TiO2 , 16.12% Fe, 9.4% CaO + MgO, 4.2% SiO2, 1.25% A12O3, and the particle size is between 0.053-0.045mm. Microwave energy was used to enhance the leaching effect. The results showed that when normal heating was used to leach the mineral, the extraction of impurities Fe, Ca and Mg was very low. However, when microwave energy is introduced, the extraction of Fe, Ca and Mg increased dramatically. The optimized conditions are: relative power 5W/g, the ratio of concentrate to HC1 isl5%, leaching at 160°C for 20 min with a ratio of liquid to solid 12:1 mL/g. The material obtained under these conditions contains 92.73% TiO2, 0.207% Ca + Mg, 0.8% Fe, with 94.6% Ti recovery. The poduct meets with the quality for boiling chlorine.IntroductionThe resources of titanium are very abundant, and are distributed all over the world. There are almost 140 minerals containing TiO2 with a content of more than 1%. However, there are only several minerals which can be used for producing sponge titanium. They are mainly rutile and ilmenite. The grade of nature rutile concentrates is higher than 95% TiO2, and it is a high quality raw material. But the resources of nature rutile are relatively low; after mining for many years, its resources are exhausting gradually. Although ilmenite reserves are great, ilmenite cannot be used as a raw material because of its low content of TiO2, only 45-70%; also it has a high impurity content of Ca, Mg and Fe. In these years, there is a tendency for titanium industry to use high grade concentrate."

Jan 1, 2012

By Ruhi Bux, Akshay Verma, Mohini Saxena, P. Asokan

"Due to the colossal increment in the industrialization, the generation of wastes gathered as a result of different extraction, benefaction and generation processes is having an alarming problem for waste disposal. The best and most acceptable way is to use the waste in accordance to its potential for the generation of high value lucrative composite goods. The study in this paper elucidates the potential of several industrial wastes like fly ash, red mud and marble slurry dust for the production of different wood substitute products like doors, windows, roofing sheets and instant houses for the rehabilitation on the sites of catastrophes. Wastes were initially characterized for the physical, chemical and mineralogical properties and then used in different formulations with binder like Polymer along with natural fiber like Jute to intensify the physical as well as mechanical properties of the resultant composite. The study also reveals that these composites have better mechanical properties than the available ones like teak, medium density board, Rice husk board etc. Also, the fly ash and red mud composites have better mechanical properties than marble slurry based composites. The results fosters the implementation of natural fiber with the industrial waste in the generation of eco-friendly and non-hazardous composites.IntroductionOver the last few decades, there has been a tremendous increase in the generation of industrial wastes gathered as a result of various extractions, benefaction and generation processes. The condition worsens even, when it comes to high quantum generated wastes like Fly ash, Red mud and Marble slurry dust. The primordial motif behind the incorporation of industrial wastes as filler in the development of composites is primarily composed of two main objectives; Firstly waste management, the colossal waste dissemination in the environment has disturbed the ecological balance by polluting land, surface water, ground water, air, natural resources and even disturbing the public health [1]. Secondly, to act as a perfect substitute for the conventionally existing building materials, this will aid in dwelling places to many with the least incorporation of exhaustive natural resources as woods quid pro quo."

Jan 1, 2008

By Caisa Samuelsson, Fredrik Engström, Bo Björkman, Margareta Lidström Larsson

"Large amounts of by-products are generated by the Swedish steel industry each year. The EAF-process generates about 400 000 ton of slag, from which 80% is deposit. An alternative to deposit is to use slag as road construction material. However, metal content in the slag can be a problem, due to the leaching. The aim of this work was to investigate how stable these materials are when ageing and kept outside. Five different EAF-slags from domestic steel plants were used in this study. The materials were characterised after 0, 6, 12, 18 and 24 month to evaluate the ageing process. Scanning electron microscope (SEM), x-ray diffraction pattern (XRD) and a standard test for leaching were used. The changes in behaviour differ between the five materials. The total leachability decreases with time for all samples. CaCO3 is formed on slag surfaces as CaO reacts with moister and CO2 in the air. Introduction The slag generation in the Swedish steel industry is about 1.5 million tonnes annually, of which more than 500 000 ton is generated in EAF (Electric Arc Furnace), AOD- (Argon Oxygen Decarburization) converters and during the refining of steel in the ladle metallurgy. Some of the slags are used in different applications, but most of the steelmaking slags produced in Sweden are landfilled today. The chemistry, mineralogy and physical characteristics of slags make it a suitable material in construction, replacing for example, gravel and rock [1]. In some respects, in road construction, it may even be technically superior to virgin material. Slag from scrapbased steelmaking is used for road construction in Europe. The reason for the low utilization in Sweden is mainly due to potential leaching of harmful elements, legislations and competition with easily available natural raw materials. Except the potential leaching, the technical obstacles for not using some slags in construction include:"

Jan 1, 2008

By Manuel Alvarado, David Nemir, Jan Beck

"Thermoelectric generation using special N-doped and P-doped semiconductors is well known as a means for direct heat energy to electrical energy conversion without the need for moving parts. The technology is used today in niche markets for low level electricity production and has been proposed as a scalable means for capturing large scale energy from waste heat streams. The choice of geometry of the thermoelements and conductors is critical to the successful implementation of a waste heat recovery system in order to manage losses due to Joule heating and diffusive heat flows. This paper describes a simulation study to define the performance impact of different aspect ratios for the active thermoelements and the electrical interconnect. The use of a finite element model that incorporates the intercoupled heat and electrical energy flows highlights some of the issues impacting scalability.IntroductionThermoelectric phenomena arise out of the intercoupled electrical and thermal currents in a material. A two-element thermoelectric generator is depicted in Figure 1. It is constructed by connecting an N-type thermoelement and a P-type thermoelement in electrical series, with both elements in thermal parallel between a heat source and a heat sink. The electrical series connection is made by attaching conductors as shown. Ideally, these series connection elements will be both good thermal conductors and good electrical conductors.The two element generator in Figure 1 is disposed between two thermal reservoirs: the heat source, which furnishes heat energy; and the heat sink, which absorbs heat energy. Heat energy flux Q, flows from the heat source to the heat sink, driven by the temperature difference between the source and the sink. As depicted in Figure 1, when a resistive load, R, is attached, electrical current, I, may be extracted from the thermoelectric generator and furnished to the load. The N-type and P-type thermoelements, are the active portions that do the actual conversion of heat energy to electrical energy. Although thermoelements may be built using conductors such as bismuth and antimony, higher efficiency thermoelectrics are built using heavily doped semiconductors. Thermoelectric devices are generally formed by connecting many pairs (couples) of N and P type thermoelements in electrical series and in thermal parallel. A commercially available module having 127 couples (254 elements) is shown in Figure 2."

Jan 1, 2011

By Frank Field, Randolph Kirchain, Elisa Alonso, Richard Roth, Nathan Fleming

"High material prices and price uncertainty can be harmful to manufacturing firms. Increased use of recycled materials, industry-wide, can lower both material prices and price variability; moreover, increased recycling decreases the use of primary material, which mitigates price increases due to scarcity effects. These stabilizing and price lowering effects are explored using an Aluminum industry model. We show that (a) increased recycling leads to smaller price fluctuations in the presence of a primary metal supply perturbation, and (b) that the more substitutable the secondary metal is for the primary metal, the lower the overall material price is.IntroductionThe price of an industrial metal is expected to be a function of both the marginal cost of extraction and its scarcity[l-2]: where scarcity can be defined as the degree to which anticipated demand exceeds the known supply. Recycling end-of-life metal increases the apparent supply of the metal, or-in a functionally equivalent, but alternative conception-lowers the demand for primary metal; this lowers primary metal scarcity and should, theoretically, reduce its price. To the extent that this theoretical prediction holds true, recycling can provide benefits to consumers of industrial metals in the form of lower prices.Using a platinum industry model, prior work by Alonso[3] has shown that increased industrywide recycling can reduce metal price volatility because the secondary metal production (a) offsets virgin metal depletion, and (b) responds to supply-demand balance fluctuations more rapidly than the primary market. However, Platinum is not a typical industrial metal in the sense that secondary metal is perfectly substitutable for primary metal: Both primary and secondary platinum metal are functionally equivalent and have a common price. Other metals, such as secondary aluminum which is used as an example case in this study, contain varying degrees of other elements that were either intentionally added, or were inadvertently mixed in with the metal during the scrap recovery process. Consequently, different grades of scrap exist that have different profiles of elements in their composition. Depending on their particular profile of elements, more or less of a given grade can be used as a mass fraction of the final alloy-the secondary metal is not perfectly substitutable for the primary metal. For the purposes of this paper, the aluminum mass fraction of the final alloy that can be made up of secondary aluminum is termed the secondary substitutability of that grade in that alloy."

Jan 1, 2011

By Teruo Bitoh, Shogo Izumi

"The effect of B203 flux melting on the structure and the soft magnetic properties of the (Feo.1sBo.20Sio.os)96Nb4 bulk metallic glasses prepared by casting has been investigated. The ringshaped bulk specimens were prepared by the B203 flux melting and copper mold casting. It was confirmed that the flux melting promotes the precipitation of the a-Fe(-Si) and Fe2B phases in the central region of the specimens. The ring-shaped bulk specimens show a flat hysteresis curve, indicating a good linear relationship between the magnetic induction and the applied magnetic field. These results show that it is possible to develop a new soft magnetic material that exhibits constant permeability, which is necessary for producing inductors and choke coils.IntroductionSince the success of forming Fe-based bulk metallic glasses (BMGs) with good soft magnetic properties, great attention has been developed to synthesis and properties of the BMGs [l, 2]. The BMGs have high glass-forming ability (GFA) and, therefore, they can be used to prepare bulk amorphous alloys with a thickness of the order of a few millimeters by casting. The soft magnetic properties of Fe-based BMGs are better than those of ordinary amorphous alloys; therefore, these BMGs have wider applications as soft magnetic materials [3-5]. It is often required for soft magnetic materials that the shape of the hysteresis curve is changed according to the demands of applications. For example, materials with ""flat hysteresis curves,"" which means the magnetic flux density (B) and the applied magnetic field (H) show a linear relationship up to rather high magnetic field, are necessary for producing inductors and choke coils. Flat hysteresis curves can be easily achieved by creating an air gap in the magnetic path. However, magnetic flux leakage generated in the air gap inhibits high-density packing of the electronic components. In order to achieve flat hysteresis curves without creating an air gap, Fe-based ordinary amorphous alloys are subjected to crystallization by annealing and transformed into thin surface layers of a-Fe; the crystallization results in the compression of the remained amorphous phase [6]. Another way to achieve flat hysteresis curves is the formation of secondary phase (such as Fe2B) that act as pinning site of magnetic domain wall displacements [7]."

Jan 1, 2013

By H. Kamiya, H. Hasegawa, M. Nojiri, S. Matsui, Y. Fukuda, M. Tsukada

"The present paper focuses on the action mechanism of anionic polymer dispersants in dense Si3N4 and SiC suspension. An atomic force microscope (AFM) was used to determine the relationship between the macroscopic suspension viscosity and the microscopic adsorbed structure of a polymer dispersant at the solid / liquid interface. The surface interactions within the suspensions were analyzed in various dispersant pH and additive conditions. The addition of an anionic polymer dispersant decreased Si3N4 and SiC suspension viscosity and increased electro-steric repulsion force on the non-oxide surface in solution at pH> 6 which was the isoelectric point of the materials. It was assumed that the increase of repulsive force was promoted by a hydrophobic adsorption of polymer dispersant on the non-oxide particles.IntroductionThe surface of silicon nitride and silicon carbide powders in a water suspension system has quite a complex molecular structure. In the case of Si3N4, hydroxyl and ammonium groups form on the surface and the pH of the suspension is increased from neutral to about 10 due to surface oxidation. The particle surface is negatively charged in alkaline solutions (pH=10), because the isoelectric point of silicon nitride exists in the pH range from 5 to 6. However, in spite of charging the negative surface charge, an anionic polymeric dispersant is generally used for the reduction in slurry viscosity.In dense SiC suspensions, an anionic polymer dispersant is generally used in order to disperse aggregates and reduce the suspension viscosity, too. Since an anionic dispersant is used in alkaline solutions higher than the isoelectric point of silicon carbide, the dispersant adsorbed on the negative charged surfaces of SiC.Few researchers have discussed and estimated the adsorption mechanism and structure of anionic polymeric dispersants on silicon nitride and silicon carbide surfaces. This is because it is difficult to observe the structure and measure the interaction at the solid/liquid interfuce directly. However, new developments in surface-force measurement technology have enabled the determination of non-DLVO type interaction for analyzing aggregation behavior2. The use of the AFM for analyzing the effects of various surfactants and co-polymers on colloidal dispersions and solid surfaces has also begun to rapidly expand to characterize the interaction between solid surfaces."

Jan 1, 2000

By Tugba Basargan Çagatay Morall, Gülhayat Nasun-Saygili

"The aim of this study is to prepare the apatitic material using colemanite mineral (2CaO.3B2O3.5H2O) which was obtained from Eastern Anatolia, Turkey. For this purpose, colemanite mineral was reacted with different phosphate sources, namely, dipotassiumhydrogen phosphate, ammoniumhydrogen phosphate and ortophosphoric acid at various temperatures and time periods. Experiments were run in batch system. The apatitic material was prepared by a wet method and followed by heat treatment at various temperatures. Structure of the samples was analyzed by XRD, FTIR, XRF and SEM. The particle size analysis was also made for the result product. The experiments showed that reaction temperature, contact time and heating temperature are important parameters to transform the colemanite into apatitic structure. Reaction of colemanite with dipotassiumhydrogen phosphate and ammoniumhydrogen phosphate results in amorphous, non-stoichiometric hydroxyapatite type structure, while acid based phosphate source gives brushite and monetite type product before and after heat treatment, respectively.IntroductionBoron which has properties intermediate between metals and non-metals is a member of semiconductor group of elements. Its atom is very small and has three valence electrons. Boron exists in Earth's crust (from 5 mg/kg in basalts to 100 mg/kg in shale) and in the oceans (4.5 mg/l) [1]. Turkey has 60% of world's boron reserves which is mostly in the form of colemanite (2Ca0.3B203.5H20). Colemanite is the most important calcium containing commercial borate mineral with 5 mol of crystal water [2].Calcium phosphate cements are very useful for bone repair applications because of its chemical structure. They are injectable, easy to shape and can be maintained locally. Because of those reasons calcium phosphate cements are very effective to fill bone defects with an irregular shape [3]. Hydroxyapatite (Ca10(PO)6(OHh) is the major component of the bone (70 wt%). However, hydroxyapatite stoichiometry, composition and crystallinity differ in human skeleton system [4, 5].The main objective of the present work was to study the transformation of colemanite to apatitic material using different phosphate solutions at several time spans and temperatures. The experiments were run in a batch system, change in pH and also weight loss were measured after the experiments. Several analysis methods were used to investigate the chemical and structural changes."

Jan 1, 2012

By Emilia Visileanu, Eftalea Carpus

"The strategy of developing the Romanian textile industry sub-sectors envisages the achieving of certain superior production indices, from a physical and value point of view, in 2010, a quantitative increase of textile wastes by 14% in 2010 as compared to 2000, implicitly. The percentage of the turned-to-profit wastes will have an increasing tendency, from 53.6% in 2000 to 74.7% in 2010. The article synthetically presents the innovative elements of the technology of processing the industry textile wastes.1. Introduction“People will need to re-adopt this sense of rarity that has been forgotten over the last two centuries. Humans need to collect, sort, recover, going back to the old ideal of alchemists: complete the material cycle, turn waste into resource, reduce all forms of predatory behaviour as much as possible”Irrespective of the historical period, geographical positioning, economic power or employed technologies, wastes resulted and will result in a bigger or smaller quantity as long as life and activity on Earth go on. The negative effects of these over the environment factors and implicitly over population health are well known all over the world and not approaching this matter enough may have catastrophic consequences over life. Having in view these aspects, finding solutions for diminishing the general waste quantity and limiting the negative effects of those products is important, by effecting the reusing of the recyclable ones in the production processes as secondary raw materials, and by ecologically treating and storing those than cannot be reused.2. Experiments and researchesThe textile industry affects the environment by the high water, energy and chemical consumption, as well as by the high quantity of wastes that are the result of using an impressive number of chemical substances and technological processes.The development strategy of the Romanian textile industry sub-sectors foresees, for 2010, the achieving of certain higher production indices as compared to 2000, both in terms of materials (as merchandise) and in terms of value, which implicitly leads to a quantitative increase of wastes.The flexible, economic and ecologic technologies which include systems of waste preliminary preparing (cutting, opening) and conventional or non-conventional system of processing the recovered fibres lay at the basis of substantiating the activity of implementing the notion of zero wastes."

Jan 1, 2008

By Riyad N. Ahmad-Bita, Shadia J. Ikhmayies

"SnO2:F/CdS:In structures were prepared by the spray pyrolysis technique on glass substrates at a substrate temperature Ts = 450°C. NH4F and HF were both tried as the sources of fluorine in the precursor solution of SnO2:F. A comparison between the properties of structures obtained by using the two doping compounds was performed. X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmittance measurements were used to characterize the films. The structures prepared by using HF as a fluorine source were found to have more ordered crystal growth, larger grain size and sharper absorption edge. From the inspection of the first derivative of the absorbance it is expected that more interdiffusion on the SnO2:F/CdS:In interface takes place in the structures made by using HF. These results confirm that these films are better as forecontacts for CdS/CdTe solar cells.IntroductionThin film CdS/CdTe solar cells built in the superstrate geometry rely on transparent conducting oxides (TCOs) to make the front contact The investigation of combined CdS-TCO films has recently been developed owing to the great interest of better understanding the effect of these bilayers on the absorbers [1]. Usually SnO2 is utilized as a front contact for these solar cells. Optimizing the properties of the SnO2/CdS structures is an important step on the way to get high performance CdS/CdTe solar cells.There are different methods to prepare SnOz thin films, such as reactive sputtering [2], evaporation [3], chemical vapour deposition [3, 4], dip coating [5] and spray pyrolysis [6-9]. At the same time CdS thin films can be prepared by different techniques such as chemical bath deposition [10], thermal evaporation [11], screen printing [12] and spray pyrolysis [7, 13]. However, the spray pyrolysis technique is a very low cost and simple technique that enables intentional doping and getting large area and uniform thin films [14]. For these reasons it is choused to prepare SnOz and CdS thin films in this work. To improve the properties of these compound semiconductors, SnOz was doped with fluorine and CdS was doped with indium where such doping is well known for these compounds."

Jan 1, 2012

By Adam Gesing, Paul Marchwica, Jerry Sokolowski, Sharon Lackie

"Often referred to as SEM-EDX, energy-dispersive spectroscopic analysis of characteristic fluorescence x-ray is a standard technique for semi-quantitative elemental composition analysis in scanning electron microscopy. It is quick and extremely useful for identification of phases in the sample microstructure, as long as the constituents are significantly larger than the probe volume from which the fluorescence x-rays originate. The probe volume ranges from a few to several microns, depending on the electron beam spot size and the acceleration voltage. We report on a new variant of an EDX technique developed to overcome this limitation and allow quantitative elemental analysis of smaller phase constituents, down to a size of several nanometers. This variant involves the calculation of compositions of individual phases from multiple analyses of areas containing phases of interest. This significantly increases the usefulness of EDX for quantitative analysis of new nano-structured materials.IntroductionIn any elemental micro-analytical method, the sample material is illuminated by a probe beam that excites an interaction volume of a sample to emit a characteristic signal. This signal in turn interacts with the sample material through absorption and fluorescence mechanisms before a portion of it is collected by a suitable detector and analyzed for elemental composition. The spatial resolution of the method depends on the minimum interaction volume between the probe beam and the sample material.Laser light beams can be tightly focused to a spot size limited by the photon wavelength and can be used to sample the surface of any material. In micro-LIBS (laser-induced plasma spectroscopy) a focused laser beam ablates and vaporizes a small volume of material from the sample surface, creating a plasma spark. Spectral analysis of the light emission from the plasma spark allows the semi-quantitative determination of the elemental composition of the material removed from the sample surface. The smallest reproducible craters achieved are ~ 3mm in diameter and a few nanometers in depth. [l]Particle probe beams of ions or electrons can be focused to a diameter of a few nanometers at the point of impact on the sample. Ions sputter the sample atoms from the point of impact, and the sputtered ionized material is analyzed by mass spectroscopy in a secondary ion mass spectrometer (SIMS). [2] This gives SIMS resolution in a nanometer range. SIMS equipment, however, is expensive and not readily available."

Jan 1, 2013

By B. Boryczko, J. Norwisz, Jose Escobedo Bocardo, Z. Kolenda, A. Holda

"Classical thermodynamic analysis of any thermal and chemical process is usually based on the first law of thermodynamics. Such an approach is not sufficient when deeper understanding of the nature of each elementary process is required. The use of the first and second law of thermodynamics together is necessary to solve practical process more effectively. Enthalpy and exergy balances allow to enhance our understanding of thermal processes especially when cumulative consumption of energy and exergy is calculated. To ensure reliability of such an analysis the least squares method for adjustment of mass balances of principal chemical elements has been applied and described in detail. Numerical analysis has been carried out to compare two different processes of copper production – shaft furnace and flash smelting.IntroductionClassical thermodynamic analysis of any technological process is usually based on the First Law of Thermodynamics in the form of energy (enthalpy) balances. Such an approach is useful in engineering practice as it makes analysis easier in the global scale neglecting modeling of the elementary processes, allows calculation of the thermal efficiency and makes possible to control quality of the measurement results. Additionally, graphical presentation of the energy balance is simple in the form of Sankey diagram.In the case of aluminum electrolysis process, design of the new electrolyzer or its modernization is always based on the enthalpy balance.However, deeper thermodynamic analysis leads to the conclusion that such an approach is not sufficient. The First Law of Thermodynamics guarantees the exact equivalence of the various forms of energy (allowing all forms to be measured in the common unit such as joules) but it does not guarantee interconversibility. Thermal energy (heat) is in a peculiar and unique position, for whereas all other forms can be completely converted into thermal energy, the reverse process id impossible, only a portion of the heat can be converted into mechanical energy. Explanation comes from application of exergy balances. As we know exergy expresses the amount of mechanical work necessary to produce a material in its specified state from components common in the natural environment, in a reversible way, heat being exchanged only with environment [1]. Consumption of exergy connected with the fabrication of some considered product appears not only in the plant manufacturing the product, but also in all plants delivering raw materials for the final production process"

Jan 1, 2008

By Daniel Kim, Michael Free, Justin McAllister, Urian Marshall, Shijie Wang

"Cathode impurity levels of electrorefined copper were evaluated based on 1/10* scale laboratory electrorefining tests. Cathodes were evaluated near the top, mid-section, and bottom sections of cathodes on both the set and mold sides and strip and scrap cycles. Slime weights were measured, and slime and electrolyte samples were also evaluated for impurities. Results from these tests have been compiled and compared to evaluate the effects of changes in operating conditions and electrode location on cathode impurities.IntroductionMany types of impurities are commonly found in commercial copper electrorefining anodes. The smelter operations that produce the anodes process concentrates that contain a wide variety of impurities that vary based on the mineralogy of the ore. Most anode impurities are removed during electrorefining. However, a portion of the anode impurities is incorporated into the copper cathode product. The mechanisms by which impurities are transported from the anode to the cathode are not well understood. Some impurities can be transported as anode slime particles to the cathode where they are incorporated into the cathode. Other impurities can be transported as dissolved species that are electrochemically reduced with the copper to become part of the cathode. Although research has been performed on anode slimes and impurities [1-4], there is a need for additional information regarding the relationships associated with electrorefining cycles, electrode faces, local electrode positions, anode impurities and specific cathode impurities. The objective of this study was to evaluate lead, arsenic, and antimony cathode impurity trends associated with electrorefining cycles, electrode faces, local electrode positions, and anode impurities. A variety of techniques including electrolyte filtering, anode heat treatment, high electrolyte arsenic concentration, high arsenic and/or lead in anodes, flocculation of slime particles, and appropriate current density control were used to vary cathode impurity levels. Each test was performed only once for a strip cycle and once for a scrap cycle. Consequently, the results for the individual conditions are preliminary and are not the focus of this study. However, the collective set of data with varying impurity modifying techniques provides a broad range of impurity levels, and the associated trends with respect to lead, arsenic, and antimony are discussed in this paper. Approximately 180 analyses of copper cathode were used to track the antimony, arsenic, and lead impurities. Eighteen anode slime samples were also analyzed for antimony, arsenic, and lead."

Jan 1, 2012

By N. Verbaan, E. Bourricaudy, M. Dry

"Starfield Resources is developing a novel circuit for the recovery of nickel, copper, cobalt, iron oxide, sulphuric acid and precious metals from the Ferguson Lake deposit in Nunavut, Canada. In this deposit, pentlandite is too finely disseminated in pyrrhotite for the production of a smelter-grade nickel concentrate at an acceptable nickel recovery, so established technology is not applicable and a novel chloride-based circuit is under development. The enabling aspect of this circuit is the hydrolysis of ferric chloride to hematite, releasing gaseous hydrochloric acid that is recycled. Conventional steps are used for separating and recovering the valuable metals from the chloride solution generated. This paper briefly outlines the circuit and presents the results of experimental work on the enabling steps, viz. the oxidation and hydrolysis of iron chloride to hematite and gaseous hydrochloric acid.IntroductionThe Ferguson Lake bulk sulphide ore body in Nunavut, Canada, owned by Starfield Resources Inc., contains significant amounts of base and precious metals but its mineralogy is such that it is not amenable to conventional processing. Pentlandite, for example, is too finely disseminated in pyrhhotite for even modem techniques such as fine grinding and improved flotation reagents to be effective [ 1] and extracting the value requires processing the entire bulk sulphide, including the pyrrhotite. To give the project a total green footprint, in terms of both carbon emissions and acid rock drainage, Starfield imposed the following requirements:• No reactive tailings to generate acid rock drainage.• No gaseous emissions other than normal atmospheric constituents.• No liquid effluents.• No regular consumption of fossil fuel.• High recoveries of all the valuable metals."

Jan 1, 2011

By Binxu Zeng, Mark Jolly, Xiaojun Dai

"The traditional investment casting foundries use batch melting and chunky running systems to produce casting components. This method leaves the energy saving issue as subsidiary one. In our research project, one of the partners, the AEROMET international PLC provides the thin wall aluminium component ""filter housing"" for test. The AERO MET uses traditional casting route to produce the filter housing, which only gives 5% --10% yield. In this paper, numerical simulation method is used to analyse filling and solidification of the casting running system. The CRIMSON running system of the filter housing is designed by using casting simulation software, MAGMAS and Flow3D. By working with AEROMET, various configurations of the casting running systems were tested and analysed. Using them ultiple life cycle approach, the energy content of new process is compared with traditional one. It indicates that the CRIMSON process only uses 36% of energy consumed by the traditional route.IntroductionThe investrnent casting is a metal for ming process using expendable patterns, which is a standard casting technique and is widely used to produce quality parts. Its accuracy, versatility and integrity tie itself to important and precious engineering components in Aerospace industry. However, traditional investrnent casting process usually uses chunky runner system and gravity filling method. It not only reduces the casting yield of the product but also causes the pouring defect during the casting. As author's previous research showed that gravity filling method pouring basin and down sprue are two main resources of entraimnent defects generation. No matter how good the running system is, entraimnent defects such as double oxide films (DOF) and bubbles will I get into the casting to cause problem."

Jan 1, 2013

By Kinya Atsumi, Kanjana Khunathai, Hisaya Kato, Hidetka Kawakita, Keisuke Ohto, Katsutoshi Inoue

"Crosslinked microalgae were prepared from the residue generated in the production of biofuel, by crosslinking-condensation in concentrated sulfuric acid. These microalgae were tested for adsorption of various metal ions in hydrochloric acid medium. The crosslinked microalgae exhibited high selectivity for Au(III) over other precious and base metal ions. From an isotherm experiment, the maximum adsorption capacity was evaluated to be 3.25 mol/kg of dry gel for Au(III) which was many times higher than that of the original microalgae residue. SEM and X-ray diffraction confirmed the formation of metallic gold particles, suggesting the occurrence of a redox reaction between surface functional groups on the gel surface and trivalent gold ion.IntroductionSubstantial quantities of precious metals are being used by the electronic industry because of their excellent electrical conductivity and resistance to corrosion. In recent years, recovery of precious metals from secondary sources such as electronic scrap [1,2 ], and leach liquors is being favored because of environmental concerns. Of course, recovery is only practical, if its cost is lower than the value of the metals (gold, platinum and palladium) recovered.Traditional methods of separation and refining do not fulfill this requirement. In order to overcome this problem, attempts have been made in recent years to develop new processes including total leaching in hydrochloric acid containing chlorine gas or hypochlorite, followed by solvent extraction and ion exchange [3]. In the new processes, new solvent extraction reagents or ion exchange resins with high selectivity and high loading capacity are used to simplify the process and to reduce the operating costs."

Jan 1, 2011

By Chikabumi Yamauchi, Mitsuru Tanahashi, Jutaro Miura, Takaharu Iwadachi, Toshiharu Fujisawa

"Tue oxidation behavior of molten Cu-Be alloys was investigated by exposing· the molten Cu-Be alloys to various Ar-O2 atmospheres to control the oxygen partial pressure, PO2 = 10 ~105 Pa at 1423 K. The following results were obtained:• The oxygen · partial pressure in gas phase affects the morphology of the oxide formed on the surface of the alloy and · the oxidation rate of beryllium.• At lower oxygen partial pressure, a molten Cu-Be alloy is covered with a homogeneous and compact internal layer of BeO. Thus, the beryllium oxidation rate can be minimized.• By adding a small amount of calcium or zirconium into the molten Cu-0.5 mass% Be alloy, a protective BeO layer is formed even at higher oxygen partial pressure. Thus, the beryllium oxidation rate can be reduced.IntroductionCopper-beryllium (Cu-Be) alloys are well recognized for their unique properties, such as high electrical conductivity, high strength, high fatigue strength, excellent properties at elevated temperatures, good formability and good corrosion resistance. .This extraordinary collection of properties are the reasons why Cu-Be alloys are expected to be ""Key-materials"", which are necessary to further advance science and technology and to be applied in.various fields such as electronic devices, machine parts, repeater housings of undersea optical fiber communication cables, etc.However, a large amount of beryllium is oxidized to BeO in melting stage of the current Cu-Be alloy production process, because beryllium is a highly reactive element. This is one of the ·main factors that negatively affect the production yield and th_e product quality."

Jan 1, 2000

By Zheng Wei, Jian Cheni, Zhenliang Weng, Wei Liang, Hongbo Zhu, Jinhui Peng, Linqing Dai, Qianxu Ye

"By testing the dielectric constant and the dielectric loss factor of concentrated Dahongshan, mill scale, anthracite and light-burned dolomite in different frequency and temperature, and by studying the temperature-rising characteristics of the materials in the microwave field of 2.45GHz in frequency, the research in the paper shows that to reach at 1250°C under the same condition -2KW the microwave power and 30g the mass --the time concentrated Dahongshan takes is 330s, whereas the millscale is 855s and the anthracite is 820s. About the last one, the higher the temperature is, the stronger the absorptivity is. After the temperature has rose to 400°C, the anthracite's absorptivity increases dramatically. The result of the research would serve as the foundation of the further study on making direct reduced iron by microwave heating.1. IntroductionUnder the microwave fields, materials' dissipation of dielectric bodies would generate thermal effect. Therefore, the dielectric constant and the dielectric loss factor are closely related to materials' ability of absorbing microwave energy-the larger the dielectric constant and the dielectric loss factor are, the stronger the material's ability of absorbing microwave energy is, and the better the thermal effect would be[1-2]. In order to research how to make reduced iron from iron ore fines by microwave heating deeply and systematically, the test of raw materials' dielectric constants and dielectric loss factors are of the essence. What's more, because a mineral' conductivity is influenced by its components and crystal structure[3], it is necessary to study different materials' different temperature-rising characteristics; hence such studies would provide theoretical foundation of further research."

Jan 1, 2012

By Padmavathy Mahadevan, Samir Chefai, Eduard Guerra

"Electrocoagulation is a technique for treating wastewater streams from metallurgical plants whereby electrodes are corroded to generate gases (most notably oxygen at the anode and hydrogen at the cathode) and solid particulates which acts as substrates for coprecipitation of impurities. The performance of electrocoagulation reactors, in terms of their efficiency for removing a particular impurity, is highly dependent on several factors, most notably: the nature of the electrodes, the spacing between electrodes, the current density, the height of the electrodes, the solution flow rate, and application of periodic current reversal. Because these variables have complex interactions, in order to ensure reliable scale-up of laboratory results, experiments should be conducted under conditions that closely match those that would be employed at an industrial scale. To that end, this article describes the design and commissioning of a versatile laboratory scale electrocoagulation reactor that allows for the control of all the aforementioned variables along with the ability to measure the instantaneous spatial distribution of current within the reactor.IntroductionArsenic is often removed from metallurgical waste streams in stirred tank reactors by coprecipitating it with ferric ions as an arsenical ferrihydrite [ 1]. Electrocoagulation is an electrolytic technology that can accomplish the same task, but has not yet been widely adopted to treat metallurgical waste streams [2]. The electrocoagulation process involves the use of an external DC power supply to drive the dissolution of a relatively non-toxic metal into the wastewater stream, usually either iron or aluminum, which then largely precipitates as oxyhydroxide phases that adsorb undesired impurities [l]. At the anode, the metal is dissolved and oxygen is often evolved, lowering the local pH and enhancing metal ion solubility."

Jan 1, 2012

By Tanm Engin, Ali Riza Tarakcilar, Derya Dispinar

"Nowadays, the casting industry is developing parallel with the information technologies (IT). Particularly the casting simulation software is being frequently used in foundry floors for casting quality control and optimisation. In this study, the filling and solidification analysis of a rolling roll manufactured by spherical graphite cast iron were carried out by Vulcan casting simulation software. The appropriate defect relieving suggestions were presented by anticipation of defects that may form during the casting process.IntroductionThe optimisation of a casting process has long been the most focused area in manufacturing plants. Many of the work involve not only the process itself but the cost as well. When it comes to the process, it is important to be able to control the defects that may form during casting.The casting process begins with the melting of a charge; followed by pouring into the mould cavity. One of the most important factors is the difference in the liquid/solid density which may lead to porosity. On the other hand, turbulence during filling is another significant factor in casting operations [1].During solidification, due to the density difference between liquid and solid, porosity might form which leads to crack-like defects. There are several other factors that may determine the quality of a casting such as segregation, inclusions, grain size and etc. However, porosity is one of the first parameters that can be easily determine and controlled by the help of simulation software. Simulation is a cost-effective tool in the optimization of process parameters and castings can be visually observed. Time loss and economic expenses could be minimized [2]."

Jan 1, 2012