Search Documents

By Sung Wng Kim

The binary antimonide compounds with the skutterudite structure have a potential for thermoelectric applications because of the high carrier mobility, high thermoelectric power, and relatively low thermal conductivity due to the complex crystal structure. However, the room temperature thermal conductivity of these skutterudite materials is as high as about IOW/mK with an estimated 80-90% contribution from the lattice thermal conductivity. Because the lattice thermal conductivity of related ternary skutterudite compounds can be substantially reduced due to the additional phonon scattering, a study of thermoelectric properties of these compounds is of interest. The binary IrSb3, ternary Ir1.xRuxSb3 and Ir(MxSb1.x)3(M=Ge, Sn) compounds were prepared by hot pressing of pre-reacted powders. We have measured the electrical resistivity, thermoelectric power, and thermal conductivity, in a temperature range from room temperature to 973K. The binary IrSb3 compound is found to have P-type electrical properties exhibiting a good Seebeck coefficient (up to 225µV/K around 773K), electrical resistivity(5x10-5Ohm M around 933K), and relatively low thermal conductivity(6W/mK around 950K). The lattice thermal conductivity, K[2] was calculated from the Wiedemann-Franz relationship.

Jan 1, 2002

By U. Meyer, A. Alonso, P. Banios

The sampling of cathodes has changed with the introduction of the ISA-process in copper refineries. A Jernkontoret joint working group of refineries and rod plants from both primary and recycled copper plants has been investigating whether the actual sampling of cathodes is representative for this type of cathodes. As a first stage, samples were sent to the members of the working group with the objective to find an easy basis for a comparison of the results of the next stages. All samples show the same tendency for nearly all elements. In some cases, there may exist differences in calibration and for some elements the detection limits are too high, especially when Optical Spectrometry is used. In the second stage, discs were compared with melted samples to answer the question whether the punching of discs is sufficient for the quality control of the cathode. The analyses of the discs represent fairly well the cathode quality. There are differences between cathodes from different crops. Three punches are sufficient to determine the cathode quality. Finally, samples from various lots of cathodes were compared with samples from the rod produced from these cathodes. The impurity content of the rod corresponds to the impurity content of the cathode.

Jan 1, 2000

By Keri Ledford, Stephanie Lin, Jason Nadler

Novel processes are being developed to fabricate thin copper thermal wick samples of a targeted porous microstructure. Structures of desired porosity, thisckness and pore size and distribution are achieved by tayloring the incorporation of sacrificial polymer beads in to slurry precursors. The thickness of the final structure is dictated by precisely controllable slurry application methods, such as spin coating. Ina subsequent heat treatment, th epolymer components thermally decompose and the remaining copper particles sinter to form a reticulated foam. The resulting microstructures are characterized in terms of porosity, permeability and specific surface area.

Jan 1, 2012

By David M. Beckwith

Increased globalization and outsource manufacturing complicate the procurement and enforcement of intellectual property rights on a worldwide basis. Recent legislative and case law developments in the United States highlight the importance of a multinational intellectual property strategy. IP lawyers David Beckwith and John Hankins will discuss planning and pitfalls in this rapidly changing trans-border environment. Topics to be discussed include harmonization with international patent laws, protecting your technology and market space with a comprehensive approach to IP, and patent enforcement issues relating to import/export of products and components in the United States.

Jan 1, 2006

By Yasumasa Hattori

Fluid flow in a flash furnace concentrate burner was investigated quantitatively in order to improve burner performance. Computational fluid dynamics was utilized for researching fluid flow in a burner port mathematically then its results were reviewed in the commercial flash furnace burner and its calculation results were found to be in good agreement with the actual measurement results. Based on those results, a mathematical fluid flow model for the Sumitomo flash furnace concentrate burner has been developed so as, to improve premixing and combustion efficiency of concentrate in the reaction shaft.

Jan 1, 2002

By M. K. Patel, K. A. Pericleous, M. Molaei

"The future trading of carbon credits and increased financial cost necessitates substantial cuts in incidental C02 emissions in the production of metals (iron, steel, aluminum, zinc, lead). Although greener methods of production are being developed, in the short term the use of point-source C02 extraction using existing technology remains attractive. Accelerated natural carbonation, in a fluidized bed is a feasible technological route investigated in this research. CFD modelling has been used to study the efficiency of C02 capture in a fluidized bed reactor containing a CaO solid sorbent. A Lagrangian/Eulerian scheme describes describe CaO particle trajectories and exchange of mass, momentum and energy with the carrier gas, with a typical off-gas composition. Different reactor geometries are considered (with uniform, stepped and gradually expanding cross-section), to maximize conversion for a given particle loading and size distribution (100-200 microns). Removal efficiencies of up to 80% are demonstrated, making this a viable process.IntroductionBased on Intergovernmental Panel on Climate Change (IPCC) reports, the major cause of climate change and global warming is due to a high level of C02 concentration in the atmosphere resulting from fossil fuel combustion, particularly in coal-fired power plants [1]. Carbon capture and storage is therefore the most important action proposed to reduce C02 from combustion flue gases. In this process, carbon dioxide is captured and may then be regenerated as pure C02 and conducted to a permanent storage, or simply stored as a solid carbonate [2]. Capture and storage of C02 has an economic penalty and the main cost of this penalty is associated with the capture plant. Capturing C02 with a lime-based solid sorbent (CaO) is a very promising technique, due to the low cost and the wide availability of the reactant. In this process, the CaO reacts with C02 based on the following reaction in a reactor called a Carbonator:"

Jan 1, 2012

By David J. Howard, Christine Broadbridge, David C. Paine

"High pressure vapor/solid reactions offer an opportunity for novel synthesis and processing of thin film materials and structures for electronic, optical, and magnetic applications. In this paper we review the use of two high pressure techniques that operate from 25 to 1000 atm (2.5 to 100 MPa) to fabricate thin film oxide structures from Si1-xGex deposited on Si wafers. High pressure synthesis enables temperature-independent control of reaction rates in the oxidation of this multicomponent semiconductor system and hence offers the opportunity to form thennodynamically metastable Si1-xGex<h from the alloy. The thermodynamics of the Si-Ge-0 system are reviewed and a method is described that utilizes selective chemical reduction (via H2 gas) of Si1-xGcx<h to form Ge precipitates in an SiO2 matrix. IntroductionAlloys of Si1-xGex grown epitaxially on Si substrates by chemical vapor deposition (CYD) and molecular beam epitaxy (MBE) have been used to create high performance microelectronic devices1. These devices show improved performance over conventional Si technology because they exploit the Si/Si 1-xGex band-gap discontinuity and take advantage of higher hole mobilities in the Ge containing alloys. While a range of devices based on heteroepitaxial systems have been demonstrated, the Si1_xGex alloys are of particular interest because they are most closely compatable with standard Si device processing. One disadvantage of Si-based materials systems is that they are not typically useful emitters of light. This is important since the use of light (rather than electrons) for transmitting and processing signals into, out of, and within Si-based microelectronics would represent a major technological advance in microelectronics-based communication and computer technologies. Nevertheless, through the use of innovative processing techniques it may be possible to use the Si1_xGex/Si heteroepitaxial system in integrated microelectronic/light-wave technologies."

Jan 1, 1994

By Ko-ichiro Ohno

It is recently recognized that the iron reduction and melting as well as the slag separation of a composite of granular iron ore and coal are completed in a very short period of about IO minutes when the composite is rapidly heated up to approximately 1673K. These phenomena are expected to be applied to a new iron-making process. The mechanism of iron ore reduction and iron-slag separation during rapid heating has not yet been revealed and the fundamental research has just started. Carburization of the reduced iron is regarded as one of the most important steps in this process. In the present work, the composite was prepared from four kinds of coal or graphite as a carbon source and electrolytic iron powder as a completely reduced iron ore. The temperature at which the liquid formation and iron carburization occurred was monitored. Direct observation of smelting reduction behavior was made by a confocal laser-scanning microscope combined with the infrared image-heating furnace to clarify the effect of molten ash on iron carburization. It was found that the meltdown temperature of composite became lower as the melting temperature of coal ash decreased. From the observed result, it was presumed that the liquid slag would act as an important media for the carbon transfer from coal to iron. The carburization mechanism during the smelting reduction was estimated as follows. When slag containing iron oxide melted down and contacted carbon, iron oxide in the slag was reduced and the formation of the metallic iron particle as well as the its carburization occurred simultaneously at the slag-carbon interface. Carburized iron particle was carried from slag- carbon to slag-iron interfaces due to the slag convection flow caused by the difference of the interfacial tension between the carbon-slag and iron-slag interfaces. Carburization of reduced iron could proceed with a repeat of the above-mentioned process.

Jan 1, 2003

By Jean-Christophe Gebelin, Mark Jolly, Samantha Jones

"The de-waxing process in investment casting is truly a black art which is carried out in a black hole - the autoclave. The process involves exposing wax, coated by a porous ceramic shell, to steam at a pressure of 10 bar and a temperature of about 180°C. The processes which then occur are truly multi-media and multi-physics. Steam condenses in the porous ceramic, wax melts and flows, the shells expand and sometimes crack. Why the shells crack is one of the most difficult questions asked in the industry.Modelling and validating the de-waxing process is not simple. The IRC at the University of Birmingham is attempting to model this process using Physica+ a code developed in the UK. This paper will present the latest results in this attempt to model one of the casting industries most intractable problems.IntroductionThe de-waxing process using an autoclave involves the following physical phenomena:· Flow of the steam in the autoclave;· Heat transfer from the steam to the wax, possibly through the shell;· Melting and flow of the wax.At the same time, other phenomena may occur, such as the flow of the steam through the shell, the condensation of the steam on the shell surface and on the wax pattern surface, the flow of wax the through the shell, etc ...This shows how complex the de-waxing process is from a physical point of view. The main defect that appears during this process is the cracking of the shell. Previous modelling work carried out by Snow [1] has shown that it is possible to predict the stress in the shell, making numerous assumptions. In this paper, the modelling to predict the state of stress in the shell that is currently in development at the University of Birmingham is presented together with the presentation ofthe physical phenomena to model and the assumptions used. The parameters that are needed in such models will also be discussed, and some experimental work undertaken at the moment presented."

Jan 1, 2001

By LeRoy C. Prichard

The scrap based steel producers in the United States generate an estimated 650,000 tons of electric arc furnace (EAF) dust annually which is classified as hazardous waste, K061. These scrap based producers commonly referred to as mini-mills represented 39% of the steel produced in 1994. Based upon the EAF plants being installed or planned today, it is a reasonable projection to anticipate 50% of the steel produced in the United States will be by EAF&apos;s. Using a straight line projection of percent of steel produced to tonnage of EAF dust generated, this will result in 833,000 tons of dust being generated upon the completion of these new EAF producing plants, presumably by the year 2000. Because the United States is a capitalistic economy, a steel producer is in business to make a profit therefore dust management becomes a very important variable in the cost of making steel. An EAF mini-mill dust management program must consider at least three components. First the handling of the dust must be in accordance with the law; i.e., the Environmental Protection Agency rules and state and local municipalities guidelines governing K061. Second, it must be an economical solution that allows a company to manage its dust processing costs, a component of its total steel production costs while producing steel at a profit. Third, the dust management program should be one that is environmentally responsible; viz., the program should reclaim or recycle the dust constituents, as feedstock materials or saleable products. The first component, obedience of the law seems to be a relatively straight forward, common sense objective; however, as nearly every mini-mill operation will testify it has been a area of changing laws with confusing variations when it comes to K061. Even more frustrating is the fact that obedience or compliance today does not mean that the company will be considered law abiding in the future.The liabilities associated with

Jan 1, 1995

By Chu Bo-Yi

"This paper contains a comparison of creep-feed and shallow-cut grinding on ceramics with both neat oil and water-based grinding fluids. When a water-based grinding fluid was used in creep-feed grinding on ceramics the vertical forces and specific energies increased markedly fast with result that the wheel surface was damaged seriously. Creep-feed grinding on ceramics with neat oil not only produced much lower grinding forces and specific energies but also resulted in the wheel remaining in good condition and minimizing damage to the ground surface. This finding may lead to a deeper understanding of the behaviors of grinding fluids in grinding processes both on ceramics and metal as well.1. IntroductionAs advanced ceramics are obtaining more and more applications in the technical area, some machining processes are needed after the sintering to reach the accuracy and finish required by components. Because of higher hardness and brittle behaviors of modem ceramic many researches have been done in order to improve grinding efficiency and surface quality.In the grinding metals the concept of creep-feed grinding has been developed in industry as a real alternative to the normal method of shallow-cut grinding. In addition to the general economic advantages, dimensional accuracy and surface integrity are invariable improved using the creep-feed grinding technique.In grinding ceramics former studies have done many works on both creep-feed and shallow-cut grinding on ceramics with water-based grinding fluids since the water-based were thought to be better coolants than neat oil in most tests of grinding metals[l]. It was suggested that the specific grinding energies of ceramics are markedly higher in creep-feed grinding. The grinding force increases vary rapidly with time in the creep-feed case. In other words, so-called speed stroke grinding with high workpiece speed is considered more suitable for improving the grinding efficiency [2][3]."

Jan 1, 1998

By Laura Garcia H, Juan Carlos Gonzalez Islas, Luis Garcia Lechuga, Pedro Alberto Ramirez Ortega

"Electrochemical studies were performed to silver recovery from industrial wastes (radiographic films) on litanium flat electrode using a filter press-type electrochemical reactor with vertical orientation (known as REOV-01), as counter electrode was used a mesh-type DSA. Voltammetric studies were employed to fmd the current range under which silver reduction occurs. Using chronopotentiometric studies with controlled current, homogeneous deposits were obtained on the surface of the Ti electrode, to a current of -210 mA during 120 minutes to a constant linear flow velocity of 15 Lmin-1 was achieved 97% of silver recovery from industrial wastes. Scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy studies corroborated the presence of silver on Ti flat electrode. In addition, the silver concentration in the solution after the experiments was 1 ppm below environmental requirements. This indicates the viability of a filter press-type electrochemical reactor with vertical orientation (REOV-01) for silver recovery from radiographic filmsIntroductionIn recent years, the industrial sector has shown an increase in the use of silver due to new applications in different areas. In sectors such as photography, the consumption of silver has declined as a result of the boom in digital photography. However, the use of silver in radiographic applications has not shown greater variation (47.16 Moz), as the image quality is essential for diagnosis in various fields, such as medicine. All the silver used in photographic applications is discarded completely (solid or in effluent). At the present, several countries have been involved in silver recovering from industrial wastes due to the economic value and environmental impact they represent. The main source of silver recovery is the wastes generated by the photographic sector. Various technologies have attempted to recover silver contained in these wastes. However, they have not fully satisfied the requirements of maximum recovery, nor environmental level (less than 5 ppm) of silver in effluents [1,2]."

Jan 1, 2014

By Leijun Li, M. M. Mahapatra

"A three-dimensional finite element model with moving heat source was developed for pulsed-laser powder deposition (PLPD) process. Experiments were conducted to study the repair of superalloy components using the PLPD process. During the experiments, IN 625 powder was deposited on a superalloy substrate similar to IN 738. The process was modeled using three-dimensional finite element analysis. Element birth and death technique was used in the finite element model for simulating the deposition of powder layer on the substrate. A moving distributed heat source was used in the thermal model for realistic simulation of the process. Temperature dependent thermal material properties including enthalpy were used for the powder and the substrate in the transient thermal analyses. The fusion zones and peak temperature distributions of the deposits were predicted from the transient thermal analyses.IntroductionPoor weldability is a critical issue of superalloy repairing. The microstructural directionality of the superalloy components are disrupted when repaired by the fusion welding processes. Currently there is no widely accepted method to economically and reliably repair directionally solidified superalloys components. Pulsed laser powder deposition process (PLPD) is a promising repairing technique as the substrate is not severely affected by the heat source.In this study PLPD technology is used as the tool for superalloy repairing. In most of the land based turbine engines the directionally solidified nickel based superalloy similar to IN 738 [1] is used as the bucket material. The turbine engine blade tips are subjected to a combination of extreme operating conditions and corrosive environment. The tip of the nickel based turbine engine blades can be repaired using IN 625 material as suggested in the literature [1-2]. IN 625 is considered to be ductile and strong enough for the purpose of Ni based turbine engine blade tip repair[1-2]. During the present PLPD investigation, IN 625 powder was used as the deposit material on an experimental super alloy substrate similar to IN 738 superalloy used as the cast superalloy for the turbine engine blades."

Jan 1, 2012

By Michael S. Moats, Jan D. Miller, Wlodzimierz W. Zmierczak

"For many, hydrogen in a pure hydrogen economy would be like natural gas in today’s energy economy. Unfortunately, hydrogen’s physical properties are unsuited to the energy market’s requirements in terms of packaging, storage, transfer, and delivery. In this paper, a hybrid energy economy that packages hydrogen chemically on carbon atoms from various sources including recycled carbon dioxide is introduced and discussed. For this new hybrid energy economy to become a sustainable reality, the ability to recycle carbon dioxide and use hydrogen to create an appropriate energy product, such as dimethyl ether (DME), is needed. DME is recognized as a potential next generation, “beyond-petroleum”, environmentally benign commodity for energy storage and distribution. It is expected that to maximize the sustainability of the proposed hybrid energy economy, “green” hydrogen will be utilized. The “green” hydrogen would be created by the electrolysis of water powered by renewable energy sources, such as solar, wind or geothermal heat.IntroductionWith the growing concerns surrounding trends in global warming and increasing concentrations of “greenhouse” gases, such as CO2 and CH4, efforts to mitigate the emission of these gases from industrial sources are growing. With respect to CO2, the demonstrations of various capture and sequestration methods are underway around the world.The sequestration of CO2 is mainly focused on storing the gas underground or deep in the ocean. The Intergovernmental Panel on Climate Change (IPCC) estimates that 2000 Gtonnes of CO2 can be stored underground in depleted oilfields, un-minable coal beds and other geologic features [1]. Additionally CO2 may be stored at the bottom of the ocean. The lure of storing carbon dioxide in depleted oilfields or un-mineable coal seams is that an economic benefit (enhanced oil or methane recovery) can offset the costs of gas capture, transportation and storage. Unfortunately, all of these storage methods have potential for the release of CO2 or CH4 back into atmosphere or creating environmental damage (mobilizing heavy metals, disrupting deep sea ecology)."

Jan 1, 2008

By Lijuan Li, Zheng Lu, Xin Xia, Qijie Zhai, Qingchun Li

"Pulsed current and pulsed magnetic field have been applied to the bainite transformation of Cr5 steel. Three groups of experiments were conducted. In the first group, ordinary resistance furnace was used for heat treatment. The Cr5 specimens were rapidly heated up to austenitization temperature 940 °C, held for 20 min, air cooled to bainite transformation temperature 350 °C, held for 10, 20, or 40 min and then air cooled to room temperature. The second and the third group shared the same temperature-time curve with that of the first group, but their heat resources came from the Joule heat produced by pulsed current. 1.5 T pulsed magnetic field was exerted on the third group specimens when they were held at 350 °C, but the second group specimens did not undergo the treatment of magnetic field. It was found that both pulsed current and pulsed magnetic field obviously retarded the bainite transformation. The phenomena were discussed in terms ofliterature results.IntroductionApplying pulsed current and pulsed magnetic field technology are very pronnsmg ways to change the microstructure of materials by affecting the phase transformation process. People had found that pulsed current dramatically influences the behaviors of materials, for example, electromigration effect [l], the solidification of metals and alloys [2, 3], electroplasticity [4, 5], crystallization of amorphous alloys [6], healing of metal materials [7] and so on. As to pulsed magnetic field technology, a lot of effort had been spent on grain refinement in solidification of metals [8, 9], recrystallization of cold-worked metals and alloys [10] and Fe-based alloys solid-state phase transformation [11, 12]. Though application of pulsed current and pulsed magnetic field technology have proliferated in recent years, investigation on their effects on solid/solid phase transformation, especially bainite transformation, is lacking. The aim of this paper is to show the effects of pulsed current treatment (C-T) and the combined treatment of pulsed current and pulsed magnetic field (CM-T) on bainite transformation of commercial Cr5 steel"

Jan 1, 2014

By Muhlis Nezihi Saridede, Burak Birol

"Plastic wastes become a huge problem day after day due to the growth of plastic industry. Hence, plastic wastes are used as a raw material for other industries to eliminate this problem. Polyethylene Terephthalate (PET), which is a commonly used for plastic bottles, may be used as a reductant for iron production because of its C and H content. In this study, composite pellets containing iron ore concentrate, flux and reductant were prepared. Crystallized PET bottles and coke were used as reductant after ground. The prepared pellets were reduced at 1400°C for 30 min. and iron nuggets were produced successfully. Usage of waste PET purely as reductant in composite pellets gives a higher metallization degree and proper carbon content than coke or PET and coke mixture.IntroductionPlastics can be seen everywhere, especially at packaging industry in our common life. The increase of plastic usage ends up with an important problem, the increase of plastic wastes. Many studies have been carried out about usage of plastics as reductant in blast furnace such as Ogaki et al.[1], Heo and Baek [2], Saridede [3], Minoru et al.[4], etc. Besides, Kato et al. [5], Nomura and Kato [ 6] and Rongfang et al. [7] have pointed out the use of plastics in coke ovens regarding to its calorific content. In EAF steelmaking, a mixture of coal/coke and plastics can be used as an energy resource instead of only coal or coke. [8] Also, the usage of PET and PC in self-reducing composite pellets increased the reduction rate. [12]PET (Polyethylene terephthalate ), which is commonly used for soft drink plastic bottles, is an important municipal waste due to its C and H content. Its molecular formula is (C10H8O 4)n. Demir and Dincer showed that PET can be crystallized at 250°C to have the ability to be ground to a size of -100 µm. [11]"

Jan 1, 2011

By Spencer Peng, Larry Wasik, Akram Alfantazi, Michael Mahon

A dynamic simulation of a zinc tankhouse is a potential tool to improve tankhouse production and cost efficiencies. A fully dynamic simulation has potential uses in the design of new tankhouses as well as in the optimization of existing facilities. Equations from previously validated models of a single cell have been adapted to the industrial dynamic process simulation software, CADSTM Plus. Based on the inlet concentration, current density, and electrode setup, the simulation can predict many parameters, including outlet concentrations, flow rates, current efficiency and energy consumption. Multiple cells have been simulated simultaneously, allowing for an entire hypothetical tankhouse to be modeled. The simulation can be used to dynamically predict the conditions in a zinc tankhouse throughout an operation time scale. Further applications of this model include, tracking impurity buildup, modeling of recycle streams and the development of new flow regimes within the tankhouse.

Jan 1, 2012

By C. Allen

A series of zinc chloride electrowinning tests was carried out in a laboratory scale cell to evaluate the effect of temperature, current density, electrolyte composition, gas sparging and additives on the performance of the cell with respect to current efficiency, voltage, specific energy consumption and deposit morphology. The anode material was DSA for chlorine evolution and the cathode was made of aluminum. At 400 A/m2 current density, a current efficiency of 90.9%, a voltage of 3.4 V and an energy consumption of 2.78 kWh/kg were observed. Air sparging was found beneficial but was not pursued for health and safety reasons. Various additives in the same chemical family as tetrabutyl ammonium chloride (TBAC1) were tested. Both TBAC1 and tetrabutyl ammonium bromide were found to be equally effective. Attempts to carry out the electrolysis at 1200 A/m2 were not as successful.

Jan 1, 2000

By S. S. Chabot, S. E. James

A recent survey of major steel companies worldwide revealed the importance of recycling zinc units from electric arc furnace (EAF) dust, mill scale, blast furnace dust and other zinc containing streams within the steel industry. Many processes have been developed and installed in response to this challenge. The most successful approach involves the production of a crude zinc oxide and its sale to primary zinc producers to recover the metal values. The problem with this process is the high concentration of halides in the crude oxide. This type of material cannot be processed directly in an electrolytic zinc plant because of the corrosion problems it will cause in electrolysis. In 1999, Big River Zinc installed a zinc oxide receiving and washing plant to minimize the impact of halides in its electrolysis circuit. A description of the washing plant and the initial operating results are presented in this paper.

Jan 1, 2000

By Wantae Kim

In order to establish the optimized recovery process for heavy minerals from Korean beach sand, we investigated the several physical separation methods such as gravity and magnetic separation followed by mineralogical characterization. There was clear relationship between the particle size and heavy mineral content that heavy minerals were mostly concentrated in the particles below 100mesh. Gravity separation using the spiral and shaking table separators made it possible to concentrate heavy minerals by rejecting the light and coarse particles consist mainly of quartz and other non-valuable minerals. The high-intensity magnetic roll separator and subsequent induced magnetic separator were applied to fractionate magnetic particles according to their magnetic susceptibility. The content of TiO2 of high susceptible ilmenite-rich fraction was 43.98wt.% while those of ZrO2 of non-magnetic and magnetic residue were 6.78wt.% and 3.11wt.%, respectively.

Jan 1, 2006