Search Documents

By C. M. F. Vieira

The main characteristics and physical and mechanical properties of clays from the county of Campos dos Goytacazes, located at the northern part of the State of Rio de Janeiro, Brazil, are presented. The characterization included mineralogical composition, chemical composition and particle size distribution. The properties related to water absorption, linear shrinkage and flexural rupture strength were obtained in samples that were prepared by 20 MPa uniaxial pressing and fired at 950 and 1100oC. The results showed that the clays are predominantly kaolinitic with high percentage of clay minerals. The kaolinitic structure associated with a small amount of fluxes confers a refractory behavior which makes difficult the sinterization and impairs the ceramic consolidation.

Jan 1, 2009

By H. Fukuyama

The wetting behavior of single crystalline MgO by fayalite-type slag melts has been studied by the sessile drop technique incorporated with high temperature X-ray radiography. The experiments were performed under oxygen partial pressures of 10-6 and 10-4 Pa at 1473 K. Mass ratios of iron to silica, Fe/Si~, in the slag employed were 1.4 and 2.0. To investigate the interfacial reaction, experiments using high density MgO crucibles were also conducted. The reactions at the interfaces were examined by Electron Probe Microanalysis. The contact angles between the slag melts and the MgO substrates were found to be relatively low, ranging from 30 to 10 degrees. The surface tension of the slag was 0.4 N/m for a slag of Fe/Si02 = 2.0. Two phases, magnesiowiistite and olivine, were observed at the interface. Interdiffusivity in magnesiowiistite solid solution was determined as a function of iron oxide content. Phase relations between magnesiowilstite and olivine, and the growth rates of both phases, are also discussed

Jan 1, 1996

By N. Kanari

The thermal decomposition studies of two zinc basic carbonate samples were carried out up to 400 "C by thermogravimetric analysis, boat experiments and differential scanning calorimetry measurements 'DSC'. The initial samples and the solid decomposition products were analyzed by scanning electron microscopy, x-ray diffraction and laser particle size analyzer. The thermal decomposition of both samples started at about 150 "C and the rate of decomposition became significant at temperatures higher than 200 "C. The apparent activation energies 'Ea' in the temperature range 150-240 "C for sample decomposition were between 132 and 153 kJ1mole depending on the sample origin. The XRD analyses of the intermediately decomposed samples and the DSC results up to 400 "C suggest that the decomposition reaction probably occur in a single step.

Jan 1, 2002

By M. Misra, J. Nanor

The precipitation and removal of arsenic from process waters can be accomplished with addition of lanthanum chloride alone or in conjunction with ferric sulfate. The long term stability of these corresponding precipitated compounds is critical from the disposal stand-point. In this paper the characterization of ferric, lanthanum and lanthanum-ferric arsenate compounds formed at room temperature in acidic and alkaline pH is presented. The characterization techniques used included zeta potential, XRD and SEM. Zeta potential measurements of ferric and lanthanum hydroxides in the presence of arsenate indicate that oxyanions of arsenate are chemically adsorbed onto the positively charged surfaces of these hydroxides. In alkaline pH there is desorption of arsenate species from the ferric hydroxide surface, hence the product is thought to be unstable. On the contrary, lanthanum arsenate is stable in alkaline pH. XRD patterns show that the ferric arsenate formed in acidic and alkaline pH is amorphous, whereas lanthanum arsenate and lanthanum-ferric arsenate formed in acidic and alkaline pH are crystalline.

Jan 1, 1999

By Mark Jolly, Xiaojun Dai

"Foundry engineers in the traditional foundry usually regard the quality of casting component as the most important issue and leave the energy saving or energy efficiency as the subsidiary one. This frequently causes disproportionate energy consumption as a result of the inefficient casting processes used and increases the production costs. This paper presents the novel CRIMSON aluminium casting process and compares its facility and melting process with traditional melt furnaces and aluminium alloy melting process. A real example is investigated to demonstrate quantitatively how the traditional foundry wastes energy and what the improvement of energy efficiency can be achieved using the new CRIMSON method. The results of this investigation will help the foundry engineer recognize the importance of energy saving and demonstrate how to use this new technology to reduce production costs and carbon footprint without decreasing the quality of the cast component.IntroductionAluminium melting in metal casting industry is an energy intensive process where it is estimated that the energy consumption is in the order of 1,700 ~ 4,700 kWh tonne-1 in using crucible and natural gas [1]. Different countries may use different energy resources for aluminium melting: in US the main energy resources are natural gas, electricity and coke [2] and in UK most of the foundry use electricity, gas and oil as energy resources [3]. Due to the pressure of rising energy price and the strict environment law, it is anticipated that under the right socioeconomic conditions, the efficiency optimisation of industrial process can be an important step toward increased industrial sustainability [4]. In metal casting industry the energy efficiency of a casting facility depends largely on the efficiency of its melting and heat treating performance. In association with the two performances, over 60 % of the total process energy costs are represented in a typical casting facility [5] where there are huge opportunities for metal casting industry to adopt the best energy practices for potential energy saving. How to ameliorate the current processes for increasing energy efficiency will have a vital effect on reducing the production costs and increasing the competitiveness. For instance, by implementing some state of the art technologies such as the CRIMSON method in aluminium alloy casting will make use of such opportunities."

Jan 1, 2011

By Merete Tangstad, Fei Li

This paper studies the quartz and carbon black pellets at elevated temperature with varying temperature and gas atmosphere. High-purity quartz and commercial ultra-pure carbon black was mixed (carbon content wt.15%), and then pelletized into particles of 1-3mm in diameter. The stoichiometric analysis of the pellet during heating is studied in thermogravimetric analysis (TGA) furnace at different temperature in CO and Ar atmosphere. The microstructure, phase changes and element content of sample before/after heating is characterized by X-ray diffraction, scanning electron microscope, X-ray fluorescence and LECO analyzer. The reaction process can be divided into two stages. Higher temperature and argon atmosphere are the positive parameters for SiC formation.

Jan 1, 2016

By Shigehito Deki

"A new wet process has been developed for the synthesis of various kinds of oxide thin films on various kinds of substrates, even which have complex surface morphology, from aqueous solution. The process was named as the LPD, Liquid Phase Deposition, method, which has some advantages over the conventional dry processes. This process can be applied to an on-site synthesis of advanced materials in the thin film technology. In this paper, some current topics on the synthesis of the composite thin oxide films by the LPD method, are presented.IntroductionGenerally, metal oxide thin films have been made by different preparative processes such as r.f. sputtering, chemical vapor depositon, CVD, laser ablation and sol-gel method, etc [1-3]. Each method has it own advantages and disadvantage. In some cases, the process is not suitable for the preparation of thin film on substrate with large surface area or complex surface morphology, and makes the deposition apparatus complicated and expenisve. By using Liquid Phase Deposition, LPD, method which overcomes some of those problems, metal oxide or hydroxide thin film can be formed on the substrate with large surface area and complex surface morphology, which are immersed into the aqueous solution only at ambient temperature and under atmosphere without any special equipments and high energy. And also, multicomponent oxide thin films can be formed readily by mixing solutions containing the objective metal ions, because it is performed in the aqueous solution which is typically a homogeneous mixing system. This process utilizes ligand-exchange, hydrolysis, equlibrium reaction of metal-fluoro complex species, MF x (x-2n>-, and F consumptive reaction. In the aqueous solution, MFx<x-2n>-is hydrolyzed with water to release F ions by a ligand exchange equilibrium reaction as following;"

Jan 1, 2000

By J. Borlée, J. P. Birat

"ULCOS is a large European program launched by a consortium of 48 partners led by arcelor and a core group of steel producers, which was started in 2004 with the support of the European Commission (RFCS and 6FP programs) to search for breakthrough process routes that could, in the future, when fully developed, demonstrate the potential of large cuts in CO2 emissions for the production of steel from iron ore.The timescale for commercial implementation is the post-Kyoto period, i.e. 15 to 20 years from today.The present paper presents the progress made in the first 2 years of this 5 year program.Several concepts are being investigated in parallel: re-engineering of the blast furnace to incorporate CCS in the core of the process, smelting reduction with CCS capabilities, massive use of natural with more CO2-lean technologies than today, hydrogen steelmaking and electrolysis of iron ore. Biomass also offers very attractive perspectives, while raising major challenges.None of these new steelmaking routes are ""no regret"", which means that the European Steel Industry has already incorporated extensive energy saving steps in its present process technology and is working as close to thermodynamics limits as is cinematically and economically feasible, and that decreasing GHG emissions further means introducing breakthrough technologies that add significant costs to the operation of the Steel Mills.They will also require much research and development before they can be proven and implemented commercially.IntroductionThe ULCOS program (Ultra Low CO2 Steelmaking) is a large research program of the European Steel Industry and its industrial and research partners launched in September 2004 to investigate steelmaking technologies that have the potential of reducing the CO2 emission of the Industry by a large amount, typically in the order of 50%. It is supported in the European Community by the 6th Framework and the RFCS programs through 3 complementary European projects [1,2].The present paper summarizes the work carried out in the phase 1 of ULCOS and in framing the program of phase 2."

Jan 1, 2008

By Sharif Jahanshahi

Calcium ferrite slags are often associated with Professor Yazawa due to his pioneering work on the thermodynamics of this type of melts. Over the past years CSIRO has invested some effort in studying physico-chemical properties of such melts to fill in some gaps in our knowledge and explore opportunities for application of the understanding developed. These investigations cover thermodynamics, transport properties of calcium ferrite based slags, as well as the kinetics of reactions of such slags with refractories. The present paper provides an overview of some of these studies and highlights some of the interesting behavior of such melts. The oxidation state of copper and arsenic in calcium ferrite based slags are predominantly Cu+ and As3+, respectively, at oxygen potentials below 10.1 atm. The concentration ofCu2+ in such slags becomes significant at oxygen potentials of greater than 10&apos;1 atm at 1300 ?C. The activities of CuOo.s and AsOl.S in calcium ferrite slags show strong deviations from the Raoultian Law, while that of CoO is very close to ideal behaviour with respect to pure solid CoO. Addition of Si02 to calcium ferrite slags can have significant effects on the activities of FeO and Fe2O3 and hence the stability of magnetite phase. Transfer of oxygen in calcium ferrite slags is fast with diffusivity of 2xlO?3 cm2/s at 1350 °C and activation energy of 16 kcal/mol Presence of solid phases, such as magnetite, has pronounced effect on the viscosity of calcium ferrite slags. The observed dependence on solid loading and shear rate indicates deviation from Newtonian behaviour. The interfacial tension between copper mattes and calcium ferrite slags is strongly dependent on the matte grade, with the determined values being much lower than the corresponding ones for interfacial tension between similar mattes and iron silicate slags. MgO, Cr2O3 and MgCr2O4 have low solubility in calcium ferrite slags and their solubility increases with increasing copper oxide content of the slag at 1300 °c. The oxidation state of the slag has strong effects on phase transformation, dissolution rate and disintegration of refractories in calcium ferrite slags. Other key factors with major impact on slag-refractory interactions include viscosity and surface tension of slags as well as the contact angle between slag and refractory material.

Jan 1, 2003

By J. L. Jambor

Previous crystal-structure determination of magnesian annabergite (Ni,MgMAsO4)2 8H2O indicated that ordering of Ni and Mg occurs in non-equivalent octahedral sites; such ordering supports the possibility of miscibility gaps on the Ni3(AsO4)2 8H2O -MgiAs04)2 8H2O. (annabergite-hornesite) join. In a predecessor study based on analyses of natural specimens, it was proposed that solid solution is incomplete both for annabergite-hornesite and annabergite-erythrite [Co, (AsO4)2 8H2O]. In the current study, syntheses by use of a slow-addition technique and aging of the precipitates indicated that the annabergite-erythrite solid solution is complete, and that no miscibility gap is present on the annabergite-hornesite join to at least 58 mol % Mg. Thus, interpretation of the compositions of these phases in oxidized mill-tailings impoundments can be done with the normal precautions for homogeneity, and without the added concern of the possible presence of miscibility gaps in the ternary system.

Jan 1, 1995

By R. E. Brewer

Pilot scale flotation tests were conducted with a l?ft-diam column at the Barrick Resources (USA) Mercur mine, Tooele County, UT, to scavenge unleached (0.01 to 0.018 oz/st) gold values from the tailings of a carbon-in-leach (CIL) circuit. The optimal recovery was 35 pct of the unamenable-to-leaching gold, at a grade of 0.353 ounces of gold per short ton, using a mixture of dithiophosphate, xanthate, and diesel fuel as a collector. This was achieved by floating approximately 1.6 wt pet of the CIL tailings. The gold values are believed to be contained in arsenic-bearing minerals, attrited carbon, and carbonaceous material in the ore. Redox potentials were measured with a gold electrode during the conditioning stage prior to flotation. The correlation between flotation recovery and redox potential values could be used to control reagent additions. Treatment of a previously leached and weathered tailings material, averaging about 0.055 ounces of gold per short ton, was also investigated. The tailings were first water leached at approximately 60? C, and the water-leached tailings, containing approximately 0.03 ounces of gold per short ton, were then fed to the column flotation unit. The effects of pH&apos; and sodium sulfide addition on gold flotation recovery and redox potentials were examined. Maximum gold flotation recovery, 36 pct, was achieved at pH 8,5 with a sodium sulfide addition of 0.18 Ib/st. Overall gold recovery by leaching and flotation was in the range of 70 to 80 pet.

Jan 1, 1989

By Zhang Duomo

A novel homogenous precipitation method, including microwave heating, solution conductivity controlling and freeze drying, was developed for the preparation of US nanoparticles. The effects of the precipitation conditions on the structure and morphology of CdS particles were discussed individually. It was found that under the experimental conditions the particle sizes were controllable in the range of 14nm to 100nm. Blend-type CdS was obtained from nitrate or sulphate solution and the more stable wurtzite-type US was obtained from chloride solution, which was ascribed to the coordination of C1 and Cd2+ altering the supersaturation of the solution as well as the different growth units and their connecting patterns, In the precipitation process the surface of US nanoparticles were surface modified with CH3CHSCOOH. The results demonstrate that the bifunctional thiols of thioglycolic acid modified the surface through Cd-S coordination bonding and the induced counter ion AOT-SO3 as the balance charge further increased the stability and dispersity of US nanoparticles. This surface-modified US nanoparticles had been used to prepare nonlinear optics and self-assemble catalysts.

Jan 1, 2003

By Hsing Kuang Lin

Extraction of zinc from chloride solution with dibutyl butylphosphonate (DBBP) in Escaid 110 has been investigated. The distribution coefficient of zinc was found to be independent of equilibrium pH. This independence indicates that the mechanism of the extraction may be solvation. Slope analysis for the system of dilute zinc chloride solution reveals that two moles of DBBP react with one mole of zinc. A series of tests were conducted to bring DBBP to its full loading capacity and the analysis of the results confirms this stoichiometric factor of 2. Extraction isotherms were established by varying either the AIO ratio or the concentration of zinc in the aqueous feed. Both curves were found to be identical.

Jan 1, 1990

By Zhenglong Li

A process has been developed to recover titanium from a blast-furnace slag which contains about 20-25% Ti02 and 12% Fe. In this process. "hot" slag from the blast furnace is directed to a separate furnace where it is reheated with additives to form two simple slag phases: one is titanium enriched anosovite (Ti3O5) and the other is a titanium lean non-crystal glass phase. The modified slag is then processed by conventional beneficiation techniques to produce a marketable titanium concentrate and a usable slag material. This paper focus on separating anosovite from glass by electrostatic separation and froth flotation.

Jan 1, 1996

By Marco Zurco, Claudia M. Mendez, Alicia E. Ares, Carlos E. Schvezov, Carlos M. Rodriguez

"Zinc-Tin alloys were solidified in horizontal form and the obtained results were analyzed. During solidification the distribution of temperatures were measured by using thermocouples located strategically along the length of the samples. From the measured temperatures the following parameters were derived; the local temperature gradient, the cooling rate and the velocities of the liquid and solids fronts. Comparing the structure of the samples and the values of these parameters it was found that the temperature gradient reaches minimum values of as low as - 0.6 °C/cm, and velocities of the fronts of around 0.1 cm/s. In addition, the grain size was measured along the samples. The results are presented and discussed in the frame of the results previously obtained for other alloys.IntroductionGenerally solidification leads to two types of grain morphologies: columnar and equiaxed. The origin of each one has been the subject of numerous theoretical and experimental researches in the field of metallurgy for many years [1-7]. The columnar-to-equiaxed transition, CET, is considered as an object of high technological relevance with respect to the directional solidification of metallic alloys. This structure transition may be sharp or gradual and it has been reported to be dependent on thermal conditions associated with the casting process, including melt convection, heat transfer coefficients at the metal-mold interface, growth rates, thermal gradients, cooling rates, transport of solute, alloy composition, melt superheat, mold temperature, mold design, casting size, casting geometry, and the concentration of nucleating particles. As a consequence, it is critical for industrial applications to understand the physical mechanisms which control this transition during solidification. Many studies highlight the importance of the relative growth of the equiaxed and columnar grains and develop expressions or numerical procedures to describe a criterion for the CET. A number of experimental investigations reported in the literature suggest that the CET occurs when GL in the melt reaches a minimum critical value [5-7]."

Jan 1, 2012

By J. T. I. Poijärvi

The smelter off-gas cleaning and the weak acid treatment at Outokumpu Harjavalta Metals Oy are presented and described in this paper. The smelter consists of the copper and nickel smelters and the acid plant of three separate acid plants two of which are double contact and one single plant and of one liquid sulphur dioxide plant. The preliminary cooling and flue dust separation of the smelter off....,gases from the copper ?and nickel flash smelting furnaces and converters? in the waste heat boilers and in the hot electrostatic precipitators are described. The final cooling and cleaning of the gases in the scrubbers at the sulphuric acid plant and the treatment of the weak acid in the vacuum and in the submerged combustion evaporators for the removal of impurities are presented as well as the treatment of the condensates from the evaporators. The attention is paid to the generation of sulphur trioxide in the smelter off-gas.and to the treatment of that in the weak acid bleed-off and to the utilization of the treated acid.

Jan 1, 1992

By J. T. I. Poijärvi

The smelter off-gas cleaning and the weak acid treatment at Outokumpu Harjavalta Metals Oy are presented and described in this paper. The smelter consists of the copper and nickel smelters and the acid plant of three separate acid plants two of which are double contact and one single plant and of one liquid sulphur dioxide plant. The preliminary cooling and flue dust separation of the smelter off-gases from the copper and nickel flash smelting furnaces and converters in the waste heat boilers and in the hot electrostatic precipitators are described. The final cooling and cleaning of the gases in the scrubbers at the sulphuric acid plant and the treatment of the weak acid in the vacuum and in the submerged combustion evaporators for the removal of impurities are pre¬sented as well as the treatment of the condensates from the evaporators. The attention is paid to the generation of sulphur trioxide in the smelter off-gas and to the treatment of that in the weak acid bleed-off and to the utilization of the treated acid.

Jan 1, 1992

By Sunil G. Warrier

A rapid infrared forming technique has been developed to fabricate titanium matrix composites. This technique applies infrared heating to infiltrate titanium alloys into carbon and silicon carbide prepregs. The entire process typically takes 1-2 minutes in an inert atmosphere. The advantages of this technique are that the process is fast, simple, does not require a vacuum or a high external pressure. The process is very economical both in energy conservation and operation costs. This technique has been used to produce void free composites with limited, well controlled fiber-matrix reactions and mechanical properties comparable to currently available titanium matrix composites.

Jan 1, 1993

By Ningchuan Feng

A biosorbent, the chemically modified orange peel, was prepared from hydrolysis of the grafted copolymer, which was synthesized by interacting methyl acrylate with cross-linking orange peel, and FT-IR spectroscopy was used for determining the structure of the biosorbent. Adsorption characteristics and effects of various factors of the biosorbent on Cu (II) were investigated including pH, adsorption time and initial concentration of Cu (II). Experiment results show that when pH was 6.0 and the initial concentration of Cu (II) was 50mg·L-1, the removal rate was 91.7% after 3 h adsorption. After four cycles being reused, 85.3% removal rate could be obtained by the biosorbent.

Jan 1, 2008

By Zhigeng Xu

Pressure leach of a Yunnan marmatite concentrates with adding coal as the elemental sulfur disperser was investigated. The experimental results show that the coal with carbon content higher than 70% is incapable of dispersing elemental sulfur from minerals and cannot improve the leaching of zinc. The coal with low carbon content (lignite coal) can act as excellent sulfur-disperser in the pressure leaching at 423K. The mechanism of lignite coal as sulfur disperser was further discussed by ultraviolet, infra-red spectrum and mass spectrum.

Jan 1, 2008