Search Documents

By W. C. Smith

Even with conservative mine planning, rib instability can progress from a nuisance to a major safety hazard. This Bureau of Mines paper examines the mechanisms of progressive rib failure in high mine openings and discusses techniques to control rib slabbing. A field test site in a longwall mine was instrumented to investigate rib behavior during mining. While data analysis showed minor pillar dilation. sporadic zones of progressive rib instability were detected that culminated in eventual rib failure. The failure occurred despite conservative pillar dimensions and shallow depth. Models were used to demonstrate the mechanisms of rib failure and then evaluate the influence of support and other mine-related parameters on rib behavior.

Jan 1, 1991

By Hassan El-Shall

The results of laboratory and pilot plant testing of a newly developed process to dewater waste slurries from different industries are presented. Data indicate that an increase in solid contents from 6% to over 30% can be obtained in few minutes retention time in comparison to several years as required by currently used technologies. The economical as well as the environmental impacts of such process are discussed.

Jan 1, 1992

By K. A. Natarajan, K. S. N. Murthy

Growth of Thiobacillus ferrooxidans on pyrite mineral surfaces and in 9K leach media was studied through estimation of bacterial protein in the different phases. Bacterial attachment was found to be governed by particle size of the mineral, period of incubation and by stationary or agitation conditions used during incubation. Increased bacterial growth in the liquid as well as on the solid phase was observed with decreasing particle size and increasing incubation periods. Increased bacterial attachment to pyrite mineral surfaces was observed to promote iron dissolution.

Jan 1, 1993

By V. T. Vacariu, P. D. Georgescu, N. Tomus

To assess the potential for radioactive pollution unique to the environmental conditions of the Bacau phosphogypsum waste dump, surface samples were taken, drillings were performed on the entire waste dump's height, and the Ra226 distribution on the height and surface considered to contain a medium content of the radium of 0.57 Bq/gr was studied. Thus, the waste dump's radioactive potential was estimated at 30-40 Ci in equivalent Ra226. Also analyzed was the granulometric composition of the phosphogypsum and the distribution of Ra226 on granulometric orders, which indicated that the radium was concentrated in the very fine fractions. Parameters were set up for the classification by hydrocycloning to obtain a fine class (less than 41 microns) having a radium content of more than 0.9 Bq/gr and a coarse class having less than 0.37 Bq/gr. A chemical process was devised for removal of the radium from the phosphogypsum with the possibility for recovering the contained sulfur.

Jan 1, 1999

By Ronald B. DeDiemar

It is generally held that cone crusher application technology is strictly an art and thus subject to the vagaries of emphirical and/or trial and error judgments. While this is basically true, certain factors have been identified which, when properly defined, can significantly reduce the element of chance. This paper will bring out these factors as well as pointing out other technologies available to predict and/or analyze cone crusher performance.

Jan 1, 1977

By W. R. Hopkins

Over 95 percent of the world's refined copper is now produced by electrolytic processes. The bulk of this electrolytic copper comes via the conventional route for sulfide ores of concentration, smelting and electro-refining. A rapidly increasing percentage of world production is now achieved using hydrometallurgical routes involving dissolution of the copper values from minerals, purification of the resultant leach solution by solvent extraction and finally deposition as cathodes by electrowinning. The technology can now be considered mature and this paper endeavors to summarize recent developments which, from the authors' perspectives, are important.

Jan 1, 1989

By Joseph Cervik, Fred Garcia

Gob holes are routinely used by the mining industry to vent methane from gobs and to prevent it from entering the mine ventilation system. In some cases, flows from gob holes are measured by centering an anemometer on the end of the discharge pipe. These measurements are erroneous and tend to be high by as much as 30%. The Bureau of Mines determined correction factors (method factors) for anemometer measurements taken in this manner. Method factors for 10.2, 15.2, and 20.3 cm (4, 6, and 8 in) ID pipe are 0.68, 0.71, and 0.78, respectively. Comparisons between horizontal and vertical flows indicated no significant change in method factors. Consequently, the method factors for horizontal pipe flows can be applied to vertical upward flows.

Jan 1, 1987

By S. K. Kawatra, S. J. Ripke

Iron ore concentrates pellets are currently in duration heat hardened (sintered) under oxidizing conditions. Pellets produced from magnetite ore concentrate are completely oxidized during induration and finish as hematite pellets. These pellets then require a blast furnace to reduce the hematite to metallic pig iron. Partially reduced pellets would save energy and fuel during transportation and further reduction. It has been stated in the literature “the most important single factor responsible for the development of strength in fired magnetite pellets containing no additive is the oxidation of the magnetite to hematite and the subsequent recrystallization and grain growth of this constituent.” However experiments shown in this paper reveal that oxidation is not necessary to produce high-strength pellets. Magnetite concentrate pellets developed similar strength when indurated at 1350°C under either oxidizing (air) or inert (argon) atmosphere; the pellets sintered under argon remained magnetite. In addition, magnetite concentrate pellets indurated under reducing (CO) atmosphere also remained as magnetite, but required induration temperature of approximately 150°C less than the other pellets.

Jan 1, 2003

By Peter Ralph

All copper ore haulage at Isamine was transferred to the new 19 level haulage network by mid 1975. Previous experience together with design studies had indicated that a three train operation would be required to haul the scheduled ore production. The ore train with a gross weight of 600 tonne is made up of 15 bottom dumping trucks hauled by twin electric locomotives (Figure 1). Present train speeds reach 40 km/hr and, in the future, this speed could be increased to 55 km/hr. The planned operation on the restricted track network and the relatively high train speed meant that the train driver operated block light system would be inadequate on the grounds of haulage safety and meeting production targets. Some form of Centralised Train Control (CTC) system emerged as a necessity, and as an initial step, tenders were called for a relay control type CTC system. The high cost of these systems and the anticipated high maintenance costs and inflexibility of the offered systems led to the rejection of the tenders. It was decided to develop a CTC system locally and to use a digital computer to perform the basic track [ ] equipment interlocking tasks and monitor haulage operation.

Jan 1, 1979

By Simon W. Houlding

This paper summarizes recent developments in computer modelling and estimation technology. Significant improvements in computational and modelling efficiencies have advanced technical computing to the stage where, for the first time, it can be realistically applied to short-term mine planning and production control. Real-time interactive grade estimation of complex shapes, volumes and grade distributions, based on immediate turn-around of production sample grades, is now possible. An added benefit is the ability to produce complete geostatistical estimates which include confidence limits. These can be incorporated into the decision making and risk assessment processes of production control. Why the need for new technology? What is wrong with the conventional methods which have sufficed for the last thirty years? The response is manyfold. They suffer from inefficient computational processes and conflicts with geostatistical theory. They are responsible for constricting the flow of information between the disciplines involved in the mine production process. Finally, it is illogical to approximate irregular geological and mining volumes with orthogonal sets of rectangular blocks. Geological materials do not occur in block formation; and mining methods which excavate rectangular blocks have yet to be developed. Other computer based technologies have evolved out of the dark ages of rectangular approximations and have successfully dealt with irregular three-dimensional geometries. It is time for computing in the mining industry to follow this example and take full advantage of available technology. To provide the necessary background, consider the basic requirements for successful implementation of technical computing within the mine production process.

Jan 1, 1992

By Terry McNulty

There are many potential pitfalls in the commercialization of innovative technology. The failures often are remembered longer than the successes, thereby serving as deterrents to subsequent attempts. The mineral industry's future depends on effective innovation. So it is essential that the causes of failure are understood. Innovation can be examined equally well in the context of geophysics, geology or mining. However the author's experience has been in mineral processing and chemical engineering. So the following discussion is limited to processes and/or plants for producing mineral concentrates, metals or inorganic chemicals. More of what follows has to do with underachievement or failure than success. But this article demonstrates that there is a strong element of predictability in the former. Furthermore, it is a credit to the minerals industry and to the engineering profession that a very high percentage of projects succeed in achieving design capacity and forecast operating costs. Innovation means the introduction of something new. In this article, the words "innovative technology" are used broadly. They include new processes and novel combinations of established unit operations, as well as novel types of processing equipment or largest-ever equipment models. The discussion of project outcomes is based on personal experience or on published information. Citations are given for technical publications that provide either project information or insights into the methodology used to analyze project performance. However, specific projects have not been identified due to the rather negative connotations of some of the conclusions drawn about the less favorable outcomes.

Jan 1, 1998

By Z. Abdel-Khalek, Hassan El-Shall, S. Farrah, C. Boice

Selective adsorption and surface modification of minerals by surfactants is the primary step in the process of separating certain minerals with similar physical and chemical characteristics in the flotation process. In this study, microorgan- isms are used as surface modifiers for francolite and dolomite. Results of adsorption experiments with francolite and dolomite show that the microbes selectively adsorb to one of the minerals under specific operating conditions. In preliminary flotation experiments, it is found that the microorganisms enhance or depress flotation of the minerals leading to an increase in the efficiency of separation between the francolite and dolomite. The conditions leading to selective adsorption (surface modification) and subsequently to possible efficient separation of these two minerals are discussed in this paper.

Jan 1, 2002

By Michael L. Maniocha

Most magnesia (MgO), whether of natural or synthetic origin, is used in the dead-burned or periclase form as refractory linings for the production of steel. Continued research in refractory science, combined with good refractory maintenance and improvements in steel-making processes, have resulted in decreased use of magnesia. To make up for this loss of business, producers of synthetic magnesia have started to manufacture a variety of magnesium-based chemicals that are used in many industries. There are three primary methods of producing MgO. The first involves the calcination of naturally occurring minerals species. Most of the magnesia produced by this method uses the rhombohedra1 carbonate mineral magnesite, MgCO,. To a lesser extent, the mineral brucite, Mg(OH), is calcined to magnesia. Magnesia produced by the calcination of minerals is called natural magnesia. The second production method uses magnesium-rich brines, or sea water reacting with lime or calcined dolomite to produce magnesium hydroxide. The magnesium hydroxide is subsequently calcined to magnesia. Material produced in this way is called synthetic magnesia. The third major method of production uses saline lake brines to produce magnesium chloride. Magnesium chloride brine is sprayed into a reactor where it thermally decomposes into MgO and HCl. The magnesia is purified by slaking to magnesium hydroxide followed by calcination. Magnesia produced in this manner is also know as synthetic magnesia (Duncan and McKracken, 1994). The degree to which the magnesium minerals or the synthetically prepared magnesium hydroxide is calcined governs the physical properties of the resulting MgO. It is the physical properties that dictate the end use for the product. The terms used to describe magnesia vary along with the degree of calcination. Table 1 summarizes the terminology used when discussing the various forms of magnesium oxide.

Jan 1, 1997

By G. A. Dawe, E. G. Kelly

Because of the nature of the breakage in the Barmac vertical spindle impactor, the 80% reduction ratio is very small, so that when an energy efficiency is calculated from Bond's method, it appears to be very low. However, the product size distribution contains a high proportion of fines. It is argued that the production of these fines accounts for the high energy consumption, and Bond's method is modified to account for this, by considering the crusher to be, effectively, a number of smaller crushers in parallel, each having a different reduction ratio.

Jan 1, 1990

By M. Galetakis

The difficulties that rise during the evaluation of multiple-layer lignite deposits come from the deposit structure (alternating lignite layers with intercalated material of varying thickness), as well as from the limitations of the applied selective mining. Thin layers of lignite and interbedded waste layers are grouped under specified assumptions regarding thickness and ash content, to form the exploitable blocks. However, in practice the decision for excavating a block is made under subjective constraints of different importance or by using uncertain data. Advances in Fuzzy Inference Systems (FIS) have provided a new approach to the evaluation of multiple-layer lignite deposits. FIS have the ability to handle imprecise or incomplete or linguistically ambiguous information and to incorporate them into decision-making processes. In the developed FIS (Mamdani type) new linguistic variables, concerning with working conditions, operators? experience and production were involved. The FIS was used for the estimation of quality characteristics and reserves of the exploitable lignite produced from Southern Field mine, Ptolemais (Greece).

Jan 1, 2005

By Chris J. Conway, Bruce W. Atkinson, Graeme J. Jameson

The flotation of coal in the fie and coarse particle size ranges presents particular problems. Fine or ultra-fine coal less than 100 microns presents a challenge to conventional flotation machines because the rate of capture of the coal particles can be very low, so longer residence times are needed. Also, conventional mechanical cells are not normally designed with froth properties in mind. Froth drainage may be inadequate, leading to excessive entrainment of ash. The upper limit of flotation of coal is normally put at about 500 um (30 mesh). It appears that, in mechanical cells, coarser particles tend to be torn away from bubbles in the turbulent environment created by the impeller. In this paper, results are presented from plant trials of a high-intensity flotation column of novel design, namely the Jameson cell. Extensive trials have been conducted on coal slurries with a top size of around 1 mm. Size-by size analysis shows that it is possible to achieve high yields of low ash product over the whole particle size range.

Jan 1, 1995

By R. V. Ramani

Control is a vital management function by which operations are brought into compliance with predetermined standards to achieve the goals of an enterprise. Events that are characterized by a low degree of expectation, avoidability, and intent necessarily have a low degree of control. Such events are difficult not only to predict but to control as well. Fortunately, very few industrial situations fall into that category of events. It is an axiom of control technology that in order to control, one must first measure; further to measure, one must know the characteristics of the subject (or environment) upon which the measurement must be made. Finally, if measurements are to be made reliably, the influences that affect the measurement must be known and, if possible, understood. The complete control cycle therefore consists of the following: (1) defining the objective, (2) planning to achieve the objective, (3) putting the plan into practice with appropriate instructions, (4) measuring variables or parameters of interest, (5) transmitting and transforming the measurements to analyze the system's status and to predict the future outcome, (6) comparing these with the defined objective, and (7) determining and taking corrective actions to bring the actual results closer to the objective. The management principle underlying the control cycle is the principle of management by exception. The application of the principle and the frequency with which corrective actions are taken vary according to the purposes of the review and control. For example, the control of a machine operation (e.g., truck on a haul road) may require adjustments and therefore data, analysis, and decisions, in intervals of seconds whereas the review for ore-grade control may take several hours. Reviews, on the other hand, for cost control may be done in intervals of weeks or months. In any case, three specific purposes of the control cycle are: (1) to correct the operation so that it follows the accepted plan closely, (2) to evaluate the operation and predict future outcomes in light of changes in the environment or of more experience, and (3) to review the objectives and modify these to be reasonable and realistic.

Jan 1, 1979

By S. D. Thompson, L. Adler

This study reviews and analyzes the empirical methods available for designing the capacities of coal mine gathering belts. The analyses lead to recommendations concerning the application and implementation of each empirical method. Operations research techniques, mainly simulation models, are also briefly mentioned, and a few recommendations are made concerning their selection and application. The objective of the study is to provide a reliable basis for the practicing engineer to properly select, apply, and implement a capacity design method.

Jan 1, 1988

By Steve Wirch, Robert Jankowski

The issue of dust control in underground coal mines has been extensively studied by both government and industry. This research work has resulted in many techniques which control the dust or help miners avoid it. Control techniques either prevent the dust from becoming airborne or cleanse the air before it can be inhaled. Avoidance measures minimize the exposure of miners to the airborne dust by blowing the dust away from work areas or making it unnecessary for a miner to occupy a dusty region. One of several successful dust control measures in continuous miner sections is the use of a machine mounted scrubber which cleanses the air and helps to prevent the contaminated air from reaching areas frequented by mine personnel. Research on the application of scrubbers on longwall shearers began in the 1970s and continued into the 1980s. The most successful projects showed only moderate improvement when a scrubber system was mounted on a longwall shearer, and the less successful projects actually increased worker dust levels. There are many reasons that scrubbers have not been successfully applied on longwalls. The most significant of these is that longwalls have across the face ventilation and generally have high face air flows. Scrubbers tend to work best when they are the primary cause of ventilation. Therefore, their capture efficiencies on longwalls tend to suffer because of the exposure of the drums to the primary airflow. Other reasons scrubbers have not been implemented on longwall s include the successful application of an excellent water spray system, effective cutting techniques, and dispersion of dust sources. These techniques can help control drum generated dust, increase production, and limit the relative effectiveness of a scrubber.

Jan 1, 1995

By K. H. McDaniel

This paper describes the development of a Windows-based interactive mine ventilation simulation software program at the Waste Isolation Pilot Plant (WIPP). To enhance the operation of the underground ventilation system, Westinghouse Electric Corp. developed a program called WIPPVENT. While WIPPVENT includes most of the functions of the commercially available simulation program VNETPC from Mine Ventilation Services Inc. and uses the same subroutine to calculate airflow distributions, the user interface was completely rewritten as a Windows application with screen graphics. WIPPVENT is designed to interact with WIPP ventilation-monitoring systems through the sitewide central monitoring system. Data (e.g., air quantity and differential pressure) can be continuously collected from the underground ventilation remote-monitoring and control system and from the mine's weather stations (psychrometric data). Furthermore, WIPPVENT incorporates regulator characteristic curves specific to the site. The program utilizes this data to create and continuously update a real-time ventilation model. This paper discusses the design, the key features and the interactive capabilities of WIPPVENT.

Jan 1, 1997