Search Documents

By S. J. Schatzel, J. D. Addis, V. Gangrade, L. L. Chasko, C. A. Hollerich

"A ventilation study using tracer gas was conducted at a western US coal mine. The objective of the study was to evaluate the movement of longwall face air exchanges between the face and worked-out area and to document the presence or absence of face airflow pathways between these locations. The mine operator uses a bleederless longwall ventilation system with a back return and a blowing mine ventilation system. The study was conducted on an active panel and included both underground and surface monitoring sites. The study used sulfur hexafluoride (SF6) released as a slug on the longwall face and in the front of the gob inby the face. The velocity of the tracer gas movement in the gob was 0.019 m/s (3.7 fpm). The rate of movement for the overall tracer gas slug averaged about 0.0091 m/s (1.8 fpm). A separate tracer gas test initiated with the release of SF6 into the legs of the first shield showed the existence of more than one pathway of face air in the general direction from the headgate towards the tailgate corner. Maintaining adequate ventilation air on longwall faces is important for worker safety and for the dilution of methane emitted from the face and caved gob. A more detailed characterization of longwall system air and gas movement allows a mine to better assess its ventilation design for controlling gas on the face and in the gob. INTRODUCTION During a series of stakeholder meetings, a near unanimous concern was expressed related to maintenance of effective ventilation airflow on longwall faces. There was a strong interest expressed regarding the impacts of face length and caving characteristics on the ability to maintain adequate face airflow levels. This study seeks to understand and improve a mine operator’s ability to monitor and control ventilation and methane concentrations across the longwall face by assessing airflow variations in terms of roof caving characteristics and face length. National Institute for Occupational Safety and Health (NIOSH) researchers seek to identify flow paths of ventilation airflow on longwall panels with variations in roof caving characteristics and longwall face lengths. The project research aims to develop an understanding of the role of gas dynamics in variable broken rock, interactions with ventilation airflow and methane concentrations across the longwall face area. The research also addresses continuous ventilation monitoring along the shield line to provide early detection of gas exchanges between face and gob, and thus improve a mine operator’s ability to monitor and control ventilation and methane concentrations around the face. In the context of this paper, the longwall gob refers to the pillared area behind the shields. This work reports on results from one project task to conduct field based research using a tracer gas to describe face air and gob area gas movement in a bleederless longwall ventilation system that incorporated a back return."

Jan 1, 2017

By F. Ansheng

Though it becomes increasingly important with the valuable minerals in their deposits tending to be fine and poor, the solid and liquid separation remains difficult especially when the particles are of micrometer size and of low density. Almost of all conventional thickeners result in that fine particles lose into overflows which often costitutes a loss of potentially valuable resources as well as an environmental hazard. The addition of flocculations may improve the settling of solids but may also not work well for the final removal of fine particles from the overflows (Ref.1).

Jan 1, 1990

By D. G. Hartley

The major copper loss at Mount Lyell is in the coarsest particles presented to flotation. An analysis of data collected from the five primary and six secondary ball mill circuits showed that grinding was limited by low breakage rates in secondary mills, possibly due to oversize balls. For 5 months, the make-up ball size for one secondary mill was reduced from 50 to 30 mm. Frequent steady-state tests indicated that overall average breakage rates could be increased by about 70% using smaller balls. A mathematical simulation of the whole circuit with increased breakage rates showed that the resultant finer grind was likely to improve copper recoveries by about 22.

Jan 1, 1981

By G. H. Harris

The flotation behavior of two high sulfur coals using a non-ionic surfactant as collector from two series of compounds containing oxygenated functional groups was studied in detail using a 2-liter Denver flotation cell. The performance of these reagents was compared with that of an oily collector, namely dodecane. The results showed that at the same coal recovery, a much lower dosage of these non-ionic surfactants was required as compared with that of dodecane. More import was the performance of these compounds as promoters for oxidized as well as un oxidized coal. Mechanisms of interaction of these compounds with the coal are suggested.

Jan 1, 1993

By L. L. Probert

A three-year project focusing on the depth profiling of respirable coal mine dust particles using scanning electron microscopy coupled with energy dispersive x-ray analysis resulted in the development of statistically classified particle-behavior models. The models depict the changing silicon fraction for 5-, 7-, 9-, and 11-keV accelerating voltages, thereby giving a clear indication of the nature of various types of particles. This paper will focus on the results for respirable quartz particles that occur in underground coal mines across the U.S. The relationship between the amount of surface-available quartz and coal seam rank is well established for Pennsylvania

Jan 1, 1994

By G. Robson

"From monitoring gas levels and air quality in coal mines to protection from collisions for large vehicles at mine sites, SICK offers a wide range of sensors and systems to improve safety and to monitor potentially dangerous situations. SICK offers solutions for the analysis and monitoring of underground coal mining atmospheres. These systems supply the coal mine operator valuable safety and ventilation information, as well as data which identify and monitors atmospheres of those production areas within the mine which may or may not be worked, such as Goafs and sealed areas. Underground coal mines contain dangerous gases, which must be monitored and controlled in order to allow productive mining operations to take place and to minimize the risk of explosion. Underground mines are a potentially dangerous place for mine workers. These are the main reasons for using Tube bundle systems SICK has had great success in selling these systems into the Australian and New Zealand Markets and this is helped by the strong drive for mine safety from both the Mine Owners and the Regulatory bodies charged with the responsibility of ensuring Mine Regulations are met. The Australian mining industry uses Tube Bundle Systems at almost all underground sites, even after mining has ceases and the mine is placed in care and maintenance. Sick has been working in international markets for some time now but has had limited success in selling Tube bundle Systems to these markets. However in recent times there has been raised interest in Tube Bundle from China, India and Turkey as these countries strive to improve mine productivity and lessen the risk of explosion or Spontaneous Combustion. Our lack of penetration into International Coal markets has been very much based on the perceived cost of the system, not the benefits to safety and productivity. Unless a mine has had an event such as spon com or a Methane explosion they rarely consider the very low level measurement capability (20 PPM CO & 100 PPM CH4) or the long term trending benefits of the Tube Bundle system. It is only after a catastrophic event the System is considered. Real Time or electrochemical Sensors are commonly used to monitor the Mine Atmosphere, the real problems of methane build up or potential Spon Com in Goafs and sealed areas cannot be monitored using Real Time Sensors as the electrochemical cell deteriorates after approx. 12 months and in sealed areas these cells cannot be maintained or replaced. Whilst the Technique of Tube Bundle Systems is quite old SICK have spent many years redesigning the Tube Bundle System into a cost effective and real value for money product. The system uses state of the art sampling and highly accurate Infra-Red wide Spectrum Analysers."

Jan 1, 2016

By J. J. DeMull, B. A. Boster

Amax's Sleeper mine uses conventional cyanidation milling and heap leaching techniques to produce gold. Since milling operations commenced in March 1986, average ore processing rates have improved from the design rate of 455 t/d (500 stpd) to more than 720 t/d (795 stpd). Heap leaching was added to the process facilities in September 1986 at a design rate of 1.5 kt/d (1650 stpd) and current heap leaching rates exceed 2.7 kt/d (2950 stpd). Presented are descriptions of the Sleeper processing facilities with emphasis on the crushing and grinding circuits, a review of the selection of crushing and grinding equipment, and a summary of operating performance during the first 16 months of operations.

Jan 1, 1990

By R. S. Shoemaker

Environmental and regulatory authorities are increasingly requiring that precious metals heap leach piles be contoured before they are abandoned so they may present a more "natural" look to the eye. Depending on the ore type, many of these contoured heaps will be subject to substantial erosion by precipitation events, native plants will have difficulty in establishing themselves and slimes be washed onto surrounding areas or into watercourses. This paper presents the argument that the results of contouring heaps are counter to good environmental practice. Calculations which have been made demonstrate that leveling and berming the heap tops as well as berming the edge of each lift or setback will effectively prevent water erosion and promote the growth of native plant species.

Jan 1, 1993

By Davar Abi-Zadeh, Cillian Brown, Deepak Kandra

"Grout backfill strategy for a particular subsurface concrete tunnel (~4.9km long, 3.5m in diameter, carrying 20” gas pipeline) was based on achieving 1:100 slope of the fill in order to progressively fill the tunnel, in a series of 350m section. Grout rheology, particularly its non-Newtonian and thixotropic behavior, determines the final fill slope for given backfill strategy. The objective of this study was to simulate the two-phase grout mix backfill process using Computational Fluid Dynamics (CFD) and determine the slope of the fill to validate and optimize the backfill strategy. Three dimensional CFD study showed that for a 500m long tunnel section with a single injection point of grout, given its rheology, it will likely keep flowing without filling the 500m section height wise. Design optimization for filling was carried out using two dimensional studies to make the backfill process “slope independent” by incorporating a 2.5m high bulkhead at ~1,000m. INTRODUCTION As part of a gas field development a 20” onshore gas pipeline is required from the landfall site to the processing terminal some 8km inland. At the landfall site the gas pipeline is routed in a ~5km underground tunnel underneath a bay. For operational reasons and planning consents as well as to mitigate environmental impact based on an environmental impact study, once the gas pipeline and the associated services and spares have been installed, the subsurface gas tunnel will be fully grouted. There will be no permanent access to the tunnel after construction is completed and the site compounds have been reinstated once works are complete. One of the key requirements is that “full grouting of the tunnel” is desired. The grouting material used is a non-Newtonian and thixotropic fluid mixture of bentonite, cement, plasticizer, retarder/stabilizer and water. The tunnel is filled progressively in 350m sections using a combination of existing and new pipework assuming the grout rheology will yield a fill slope of 1:100 in a 350m section. The proposed grouting system used one pump at the grouting compound to pump the grout into the tunnel using the existing tunneling pipework. For the longer runs a second booster pump was used in series to pump the grout to its final discharge location. The filling process is controlled via a system of flow meters, pressure transmitters and a tunnel CCTV system."

Jan 1, 2016

By Dae Young Kim, Sim Bo Kyung, Ebrahim Farrokh, Ki Chang Hyun

"TBM cutter life evaluation in abrasive granitic rocks is a very important issue, especially in pressurized face tunneling with mixshield TBM for which the planning of costly interventions becomes crucial. This paper presents an overview of methodologies for cutter life evaluation in rock. A comparative study is performed to indicate the predictability of cutter life evaluation methods based on detail data from the NS3 tunnel project in Singapore. A new model is developed based upon the cutter wear information of eight TBM tunnels from around the world. New methods are proposed to evaluate the optimum intervention interval length and the number of worn-out disc cutters for a tunnel project. Finally, two new laboratory tests in the evaluation of disc cutter abrasion, including a full-scale and a small-scale test, are introduced, and their test results are discussed. INTRODUCTION The issue of wear evaluation for hard rocks has been extensively studied in drilling and pavement industry. In this regard, several tests and evaluation methods have been proposed to estimate or evaluate the state of tool life (e.g. bit life for drilling). In the case of TBM tunneling, tool wear may depend on several factors such as mineral composition, strength, or type of cutting, but as the abrasion is usually the major mechanism for the tool wear in hard rock, the developed methods for cutter wear or cutter life evaluation are mostly based on the abrasion indices such as Cerchar Abrasivity Index (CAI). This paper attempts to review the major methodologies for disc cutter wear and life evaluation and to propose new methods to evaluate cutter life and intervention interval evaluation based on detail information of a mixshield tunnel project in Singapore as well as general information of some other projects from Iran, Italy, South Africa, and France. As the laboratory tests are crucial in the process of evaluation, two new lab tests are developed and used to inspect suitability of the new proposed model for disc cutter wear evaluation."

Jan 1, 2016

Laboratory tests were conducted to evaluate the silica collection efficiency of flooded-bed scrubbers with six different filter panel designs and at two operating velocities. Test results indicated that reductions in filter density negatively impacted respirable dust collection. Silica collection efficiency for the least dense filter was as much as 33 % lower than the collection efficiency of the densest filter. At the low operating velocity, the least dense filter allowed over 40% of the respirable silica dust in the scrubber intake air to pass through the unit, where it would be discharged back into the mine environment. Operation of the scrubber at the higher test air velocity increased silica collection efficiency, regardless of the filter panel tested. The density of the filter panels also impacted the quantity of air that is moved through the scrubber, with higher density filters reducing scrubber airflow. For each filter, the relationship between dust collection efficiency and air moving capacity must be considered to determine overall effectiveness for specific mine applications.

Jan 1, 1998

By Rob Thomas

It is generally agreed that standing support should be installed in roadways that will for various reasons, be holed through with a longwall. Considering the magnitude of the associated abutment loading in conjunction with the need to ensure that the material used is cuttable, some form of cementitious support is often used.

By H. B. Oblad

Coal/pyrite fines were froth floated in a laboratory cell to examine the rate of pyrite recovery during conventional coal flotation. The effects of collector, particle size and carbon to total sulfur ratio on the kinetics of recovery were investigated. These data coupled with microscopic examination suggest that miniscule amounts of coal that remain attached to the pyrite surface affect the rate of flotation of pyrite.

Jan 1, 1985

By Miroslaw M. Hajdasinski

A project's rate of return (ROR) [The list of all the acronyms used in his text is provided at its end.], be it an internal or external one, usually needs to be approximated. The success and efficiency of an approximation procedure depend on the quality of the initiating parameters such as bounds or seed values (guesses). Current approximation procedures commonly use bounds and guesses dictated by intuition rather then by mathematical consideration. The paper presents three ROR-bounding and six ROR-guessing approaches and examines their suitability on the examples of the typical project cash flow patterns.

Jan 1, 1996

By S. K. Kawatra

Outokumpu Electronics has designed a new on-line coal slurry ash analyzer, based on an instrument developed at Michigan Technological University. The primary goal was to build an accurate instrument at the lowest possible cost. The instrument determines ash content from measurements of x-ray backscatter, iron Ka fluorescence, and low-energy y-ray absorption. It is capable of measuring the ash content with a standard error of 1.1% ash over an analysis range of 9-21% ash and 7-22% solids. The analyzer was tested on coals from United States, Poland, Great Britain and the USSR.

Jan 1, 1992

By Tim Cleary, Steve Skelhorn

The 9th Line / 16th Ave tunnels are part of a $700 million expansion of the York Durham Sewage System, north of Toronto. The 15 km of tunnels presented many challenges, including glacial and postglacial deposits, at depths up to 55 m. Due to high hydrostatic heads, the Owner specified EPB tunnelling, however, an alternate was proposed utilising rib and lagging tunnels, combined with a de-watering scheme. State of the art technology was utilised with a new Lovat TBM, incorporating PLC control, soft start water-cooled motors and a head designed to tackle the mixed ground expected. The 9th Line tunnels were completed in 2002. Subsequently the second section of tunnel along 16th Avenue has been awarded to the Joint Venture. This paper presents a case history of the soft ground tunnelling, including design elements, tunnel systems and TBM operations.

Jan 1, 2003

By Jafar Safarian, Leiv Kolbeinsen, Stian Seim, Hossein Salehi

The present work aims to investigate the link between the oxidation and reduction of a weathered ilmenite concentrate in terms of phase transitions, microstructural changes, and element distribution. An ilmenite concentrate sample was pelletized and fired at 1000 °C in air, and as a result, the pellets were oxidized. The oxidized pellets were reduced by hydrogen gas at 1000 °C, which yielded almost complete metallization of the iron content of the pellets. The ore and the pellets were characterized in each step by XRD and SEM techniques, and distribution of elements and phases were investigated. Ilmenite, pseudorutile, and rutile were the main phases detected in the ilmenite concentrate sample, and depending on the weathering degree of the particles, different fractions of the phases were identified in their microstructure. It was found that irregular rutile grains dispersed in a pseudobrookite matrix is the morphology of the oxidized ilmenite phase. However, increasing microcracks and porosities were the only microstructural changes in the pseudorutile phase after oxidation in air. Studying the specific types of the ore particles and their oxidized and reduced forms indicated that the phase distribution in the ilmenite ore particles dictates the phase distribution in the oxidized and reduced ones. Results show that the morphology of the reduced particles includes a titanium (III) oxide matrix in which reduced iron globules are dispersed.

Feb 8, 2021

By J. V. Bymark

It is the intent of this paper to discuss the autogenous grinding circuit at Hibbing Taconite. The scope of the presentation includes; a brief history, the process flowsheet and the steps taken to improve mill productivity, availability and metallurgical performance. Hibbing Taconite is located near the center of the Mesabi Range in Northern Minnesota 100 miles from the Canadian border and 80 miles north of the Lake Superior Port Cities of Duluth and Superior. A 105 mile railroad connects us with the port of Superior, Wisconsin, where our pellets are loaded into lake carriers for lower lake destinations. It is worthy to mention the Mesabi Range's most famous landmark which is immediately to the south of our mine area. This is the Hull Rust Mahoning Mine which operated until the mid-1970's producing more than 700 million tons of red ore between 1893 and 1973.

Jan 1, 1985

By Alexander N. Winchell

The cities of St. Paul and Minneapolis are located side by side on a double loop in the Mississippi River near the eastern boundary of Minnesota. Both cities lie on both sides 'of the Mississippi River, which in this region describes an S-shaped curve. The two cities together have a population of over 600,000 people, gathered in an area which has grown to be a single urban district inasmuch as the two cities have expanded until they occupy all the territory formerly between them, though the business centers are ten miles apart. St. Paul is located at the head of navigation on the Mississippi River and Minneapolis, farther upstream, at the Falls of St. Anthony. A recent water¬power development below the Falls of St. Anthony, constructed by the Federal Government, has at the same time made possible navigation to the foot of St. Anthony Falls through a lock around the dam which replaces the former rapids. Minneapolis, in 1920, had a population of 380,000 people, and St. Paul, 235,000. The two cities occupy land at an elevation of 700 to 900 feet above sea level. The average elevation is slightly less at St. Paul. Minneapolis has nearly 4,000 acres of parks and park¬ways, while St. Paul has nearly 2,000.

Jan 1, 1920

By David G. Kidd

The principles of Ore Sorting in general and photometric sorting in particular are discussed with detailed reference to the Model 16 machine. The operating principles and design of the Model 16 are discussed and a case study presented to demonstrate the use of sorters to process an industrial mineral. In addition, an economic study is presented, to highlight the benefits of ore sorting, by evaluating the increased revenue that can be achieved using an ore sorter to process a particular ore body.

Jan 1, 1983